Multi-functional nanopatterned optical films fabricated using capillary force lithography

We demonstrate anisotropic optical films based on liquid crystalline polymer (LCP) using a capillary force lithography (CFL). The fabricated optical films can be used as both an optical component and a self-aligning capability of liquid crystal molecules introduced on the film. Additionally, HA or PA LC can be induced on same material by controlling the water repellency of LCP surface. Moreover, surface anchoring transitions could be controlled by variation of pattern sizes and surface treatment. In this point of view, one thin optical film can act both retarder and alignment layer and then shows good retardation, LC alignment, and transmittance at the same time.     

UV-driven switching of chain orientation and liquid crystal alignment in nanoscale thin films of a novel polyimide bearing stilbene moieties in the backbone

A novel photosensitive polyimide, poly(4,4'-stilbenylene 4,4'-oxidiphthalimide) (ODPA-Stilbene PSPI) was newly synthesized. The most surprising feature of this PSPI is that the PSPI films irradiated with linear polarized ultraviolet light (LPUVL) can favorably induce a unidirectional alignment of liquid crystals (LCs) in contact with the film surface and further switch the director of the unidirectionally aligned LCs from a perpendicular direction to a parallel direction with respect to the polarization direction of LPUVL by simply controlling the exposure dose in the irradiation process. These LPUVL-irradiated films were found to provide high anchoring energy to LCs, always giving very stable, homogeneous cells with unidirectionally aligned LCs regardless of the LC alignment directions. In the films, the PSPI polymer chains were found to undergo favorably unidirectional orientation via a specific orientation sequence of the polymer chain segments led by the directionally selective trans-cis photoisomerization of the stilbene chromophore units in the backbone induced by LPUVL exposure. Such unidirectionally oriented polymer chains of the films induce alignment of the LCs along the orientation direction of the polymer chains via favorable anisotropic molecular interactions between the oriented polymer chain segments and the LC molecules. In addition, the PSPI has an excellent film formation processibility; good quality PSPI thin films with a smooth surface are easily produced by simple spin-coating of the soluble poly(amic acid) precursor and subsequent thermal imidization process. In summary, this new PSPI is the promising LC alignment layer candidate with rubbing-free processing for the production of advanced LC display devices, including LC display televisions with large display areas.     

Alignment of liquid crystals using Langmuir‒Blodgett films of unsymmetrical bent-core liquid crystals

ABSTRACT

The properties of the thin films of liquid crystal (LC) molecules can be governed easily by external fields. The anisotropic structure of the LC molecules has a large impact on the electrical and optical properties of the film. The Langmuir monolayer (LM) of LC molecules at the air–water interface is known to exhibit a variety of surface phases which can be transferred onto a solid substrate using the Langmuir?Blodgett (LB) technique. Here, we have studied the LM and LB films of asymmetrically substituted bent-core LC molecules. The morphology of LB film of the molecules is found to be a controlling parameter for aligning bulk LC in the nematic phase. It was found that the LB films of the bent-core molecules possessing defects favour the planar orientation of nematic LC, whereas the LB films with fewer defects show homeotropic alignment. The defect in LB films may introduce splay or bend distortions in the nematic near the alignment layer which can govern the planar alignment of the bulk LC. The uniform layer of LB film facilitates the molecules of nematic to anchor vertically due to a strong van der Waals interaction between the aliphatic chains leading to a homeotropic alignment.     

Factors in liquid crystal photoalignment on polymer films: photoorientation versus self-assembly

We demonstrate that photostimulated self-assembly, running in parallel with molecular photoorientation in the top layer of the aligning polymer film, breaks the bulk molecular order mainly determined by the symmetry of irradiation. This may substantially modify liquid crystal (LC) alignment. Depending on the chemical composition of the liquid crystal, the self-assembled layers may influence either homeotropic or planar LC alignment with extremely weak azimuthal anchoring. Effective self-assembly occurs in polymers having side chain chromophores with flexible spacers and polar terminal groups.     

The effect of surface polarity of glass on liquid crystal alignment

The effects of the surface polarity of a glass substrate on the orientation of nematic liquid crystals (LCs) were studied using the polarised optical microscope and Fourier-transform infrared spectroscopy. On the surface of oxygen plasma treated glass, a homeotropic alignment of LCs was induced for LCs with negative dielectric anisotropy. This suggests that vertical orientation of LCs could be induced on a polar glass substrate without using an LC alignment layer. Upon cooling towards the isotropic–nematic transition, E7 with positive dielectric anisotropy changes its LC arrangement to isotropic, homeotropic, planar orientations in order. The nematic LC anchoring transition of E7 was interpreted by considering the competition between van der Waals forces and dipole interactions that control the alignment of LC molecules on a polar glass surface.     

Vertical alignment of liquid crystal on tocopherol-substituted polystyrene films

We synthesised a series of vitamin-based and renewable tocopherol-substituted polystyrene (PTOC#, # = 20, 40, 60, 80 and 100), where # is the molar content of tocopherol moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a higher molar content of tocopherol side group showed vertical LC alignment behaviour. The vertical alignment (VA) behaviour was well correlated with the surface energy value of these polymer films. For example, VA was observed when the surface energy values of the polymer were smaller than about 35.22 mJ/m² generated by the nonpolar tocopherol moiety having long and bulky carbon groups. Good electro-optical characteristics, such as voltage holding ratio and residual DC voltage, and aligning stabilities at 200°C and ultraviolet irradiation of 10 J/cm² were observed for the LC cells fabricated using PTOC100 as a LC alignment layer. Therefore, it was first found that the renewable tocopherol-based materials can produce an eco-friendly vertical LC alignment system.     

Electro-optical effects of anchoring transition in polymer dispersed liquid crystal films

Two groups of polymer dispersed liquid crystal films have been studied, one with a fixed cell thickness but varying liquid crystal (LC) concentrations and the other with a fixed LC concentration but varying cell thicknesses. A sudden decrease in transmittance with increasing temperature was observed for films whose LC domain sizes were comparable to their cell thicknesses. In particular, spontaneous alignment of LC directors was observed below ∼20°C when LC domains were formed spanning the space between upper and lower indium tin oxide-coated glass substrates. With increasing temperature, this axially aligned homeotropic configuration changed gradually into homogeneous configurations. We believe that the sudden decrease in transmittance originated from the anchoring transition at the glass substrates and polymer walls. In addition, it has been found that the intensity of ultra violet irradiation has a strong effect on the director configuration of LC domains, and that the cure temperature affects the anchoring transition temperature significantly.     

Weak surface anchoring energy of 4-cyano-4'-pentyl-1,1'-biphenyl on perfluoropolyether Langmuir-Blodgett films

Functional director alignment layers are needed for high performance liquid crystal displays (LCDs). Reported herein is a novel polymer material for LC alignment, namely, perfluoropolyether (PFPE), which exhibits a weak surface anchoring energy for bend deformation and is amenable to simple fabrication of grooved surfaces by soft lithography, a surface topography desired for multistable LCDs. Liquid crystal optical cells fabricated using Langmuir-Blodgett films of PFPE (of variable thickness) exhibited weak surface anchoring energies on the order of 10(-5) Jm2 for the nematic liquid crystal 4-cyano-4'-pentyl-1,1'-biphenyl with no dependence on film thickness.     

Homogeneously aligned liquid crystal molecules on unidirectional buckle pattern of polyurethane films

We present the fabrication of an anisotropic structure on a polyurethane (PU) film for aligning liquid crystal (LC) molecules with ion beam (IB) irradiation at an incident angle. The obtained anisotropic structure assembles the LC cells in a layer that aligns LC molecules uniformly. Polarised optical microscopy images of an LC cell fabricated with IB-irradiated PU were captured to confirm the LC alignment state and compared with those fabricated with non-treated PU. To analyse the effects of the IB irradiation, X-ray photoelectron spectroscopy and field-emission scanning electron microscopy were used to investigate the chemical and morphological modifications, respectively. IB irradiation modifies the chemical structure of PU, which indicates that a new skin layer is formed on the PU films. This skin layer generates an in-plane compressive strain, thereby creating buckles on the PU films. Simultaneously, the physical collision of the reactive Ar⁺ ions during IB irradiation induces a directional strain on the surface, thereby forming a unidirectional structure of buckles along the direction of IB irradiation. The PU film annealed at 200°C showed the high average transmittance of 88.9%, which is appropriate as an alignment layer.     

Preliminary communication Investigation of pretilt angle generation in nematic liquid crystal with oblique non-polarized UV light irradiation on polyimide films

We investigated new rubbing-free techniques for liquid crystal (LC) alignment with non- polarized ultraviolet (UV) light irradiation on plates coated with two kinds of the polyimide (PI) films. It was found that monodomain alignment of nematic (N) LC is obtained in the cell having a PI surface without a side chain. We successfully observed that the generated pretilt angle of the NLC is about 3 with an angle of incidence of 70 on the PI surface without side chains. This pretilt angle generation is attributed to interaction between the LC molecules and the polymer surfaces; the uniform alignment of NLC is attributed to anisotropic dispersion force effects due to photo-depolymerization of polymer on PI surfaces.     

Analysis of the rewriting time of liquid crystal optical rewritable e-paper

Theoretical and experimental analysis of the rewriting time of liquid crystal (LC) optical rewritable (ORW) e-paper was conducted. The equations of rewriting time of alignment molecule SD1 film with and without interaction with LC based on diffusion model were derived, which shows that the rewriting time of LC ORW e-paper could be shortened by enlarging light intensity or decreasing azimuthal anchoring energy. The rewriting time of pure SD1 films and LC ORW cells was measured under different light intensities. And LC ORW cells with different azimuthal anchoring energy were prepared for rewriting time measurement. A good agreement between experimental and theoretical results was obtained, which indicates that using larger light intensity and making LC cell with smaller azimuthal anchoring energy, ORW rewriting time could be decreased to the amount suitable for practical use.     

The characteristics of SnPc-doped ferroelectric liquid crystal cells

Tin phthalocyanine (SnPc)-doped polymer films were used to align ferroelectric liquid crystals (FLC). A stripe-shaped domain structure was obtained spontaneously in the initial alignment of the surface-stabilized cells. Atomic force microscopy (AFM) was introduced to investigate the aligning films. It was discovered that the modified aligning films show a polymer aggregate chain structure oriented along the rubbing direction that may play an important role in the FLC alignment. The stability, memory capability and response time of the cell were improved and enhanced through the doping process.     

Bent-core liquid crystal-functionalised flexible polymer substrates for liquid crystal alignment

ABSTRACT

A transparent flexible polymer film is chemically functionalised with a bent-core liquid crystal (BCLC) compound for effective alignment of the bulk BCLC sample at the substrate–LC interface. The surface attachment was achieved via a simple procedure which involved pre-treatment of the polymer film (commercial name: over head projector film) using piranha solution followed by chemically attaching the BCLC compound through silane condensation reaction. Surface characterisation of the unmodified and BC-modified flexible films was carried out through X-ray photoelectron spectroscopy (XPS), attenuated total reflectance fourier transform infrared (ATR-FTIR) spectroscopy, contact angle (CA) and atomic force microscopy (AFM) techniques. The BC-modified flexible substrates are analysed for their efficiency to orient the bulk LC sample. Remarkably, the chemically modified polymer substrates are highly efficient in vertically aligning both the BC and rod-like LC samples at the substrate–LC interface, in comparison to their unmodified counterparts. The described method is simple, reproducible, surface modified substrates are highly stable and more importantly reusable. The demonstrated method for the alignment of BCLCs advances a step forward towards the realisation of applications proposed for these fascinating compounds.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Control of anchoring of nematic fluids at polymer surfaces created by in situ photopolymerization

In situ photopolymerization of alkyl acrylate monomers in the presence of a nematic fluid provides a cellular matrix of liquid crystalline droplets in which the chemical structure of the encapsulating polymer exerts control over the alignment (anchoring) of the liquid crystalline molecules. Control is obtained by variation of the alkyl side chains and through copolymerization of two dissimilar monofunctional acrylates. For example, among a series of poly(methylheptyl acrylate)s, the 1-methylheptyl analogue prefers planar anchoring of a nematic (TL205) over the temperature range studied. However, the polymers of other methylheptyl side chains display a homeotropic-to-planar anchoring thermal transition temperature similar to that of the n-heptyl analogue. Copolymerization of two monofunctional acrylates with opposing tendencies of aligning liquid crystal leads to tunability of anchoring behavior over a wide temperature range. The broad anchoring transitions we observed provide a way of achieving highly tilted anchoring.     

Homogeneous liquid crystal alignment on poly(vinylidene fluoride-trifluoroethylene) films subjected to ion-beam irradiation

We demonstrate homogeneous and uniform liquid crystal (LC) alignment on poly(vinylidene fluoride-trifluoroethylene) [PVDF-TrFE] films using ion-beam (IB) irradiation and a performance improvement of twisted nematic (TN) cells using IB-irradiated PVDF-TrFE films. Spontaneous ferroelectricity of the PVDF-TrFE films was modified by IB irradiation, which affected the LC alignment properties. The variation in the pre-tilt angles of the LC molecules on the IB-irradiated PVDF films is attributed to surface reformation, including defluorination and oxidation because the pre-tilt angles of LC molecules can be controlled by adjusting the fluorine content. The results of contact angle measurements supported this phenomenon. A 58% reduction in the switching voltage was observed for TN cells, indicating that the IB-irradiated PVDF-TrFE films are a promising candidate for use as an alignment layer.     

The effect of polymerizable surfactants on morphology and electro-optical of PDLCs films based on epoxy acrylate system

Polymer dispersed liquid crystals (PDLCs) have been extensively studied for various excellent electro-optical applications. The anchoring interaction of liquid crystals (LCs) molecules on the surface of the polymer cavity surrounding an LCs droplet has a crucial effect on the electro-optical performance of the PDLCs. The effect of polymerizable surfactants on the electro-optical properties of PDLCs films was studied in detail. The active double bonds were polymerized with prepolymer to stabilize the performance of polymer matrix. The experimental results showed that polymerizable surfactants could effectively reduce the driving voltage. The speed of polymerization was monitored by real-time transmittance. The electro-optical properties of PDLC films were measured by Polarimeter (PerkinElmer Model 341). The driving electric field was reduced from 3.9 V/μm to about 2.8 V/μm for doping undec-10-enoic acid at curing temperature 80?°C. The surfactants containing polymerizable functional groups, polarity, and alkyl chain weakened the surface anchoring between LCs droplets and polymer interface. The morphologies of PDLCs films were also investigated by polarizing optical microscopy (POM) and Fourier transform infrared (FTIR) images. The LC droplets were encapsulated by polymerizable surfactant according to FTIR images.     

Anchoring properties of a nematic liquid crystal on anisotropic hydroxypropylcellulose films

Thin solid films of hydroxypropylcellulose (∼15-30 µm) prepared from liquid crystalline and isotropic aqueous solutions are used as liquid crystal alignment layers. Using the standard nematic liquid crystal 5CB we measured the interface properties of these solid films as a function of the polymer concentration in the aqueous precursor solution, expressed in terms of zenithal and azimuthal anchoring orientations and extrapolation lengths. The hydroxypropylcellulose thin films are found to induce a planar orientation of 5CB independently of the polymer concentration, with the alignment along the polymer backbone. The zenithal anchoring strength is found to be strong and essentially independent of the temperature far from the nematic-isotropic transition, with an extrapolation length ξ_θ≈50 nm. The zenithal anchoring becomes weaker near the nematic-isotropic transition, as expected. The azimuthal anchoring strength is found to be intermediately weak and strongly dependent on the polymer concentration, with an extrapolation length varying from ξ_θ≈250 nm to ξ_ϕ≈500 nm. These films are particularly interesting since their surface topography and morphology may be tuned by varying a few parameters in the film preparation process, such as the polymer concentration in the aqueous solution.