Studying the mechanism of thioketone‐mediated polymerization via electrospray ionization mass spectrometry

The polymeric product spectrum generated in thioketone‐mediated free radical polymerization (TKMP) was analyzed via electrospray ionization mass spectrometry. Poly(n‐butyl acrylate) samples were synthesized in the presence of the (commercially available) thioketone 4,4‐bis(dimethylamino)thiobenzophenone under variable reaction conditions in toluene solution at 80 °C. To unambiguously assign the mass spectra, the samples are prepared under variation of the monomer (going from n‐butyl acrylate to ethyl acrylate) as well as by employing variable thermally decomposing initiators [i.e., 2,2′‐azoisobutyronitrile and azobis(cyclohexanecarbonitrile)]. In all mass spectra, significant amounts of the expected cross‐termination product, formed via bimolecular termination of propagating macroradicals with the dormant thioketone radical adduct (consisting of a propagating chain and the mediating thioketone) alongside conventional termination products can be identified. As the study was carried out on acrylate polymers, acrylate‐specific reaction products arising from intramolecular transfer reactions followed by β‐scission of the generated mid‐chain radicals are also identified in the mass spectra. In addition, a species congruent with the dormant thioketone radical adduct itself (oxidized to its cationic state) was identified. Products that could potentially be formed via a chain transfer mechanism cannot be identified. The results presented here thus support the earlier suggested TKMP mechanism involving a highly stabilized adduct radical which undergoes significant cross‐termination reactions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1864–1876, 2009     

Chain‐transfer reaction in the radical polymerization of di‐n‐butyl itaconate at high temperatures

Radical polymerizations of di‐n‐butyl itaconate were investigated. Unexpected resonances (C resonances) were observed in ¹³C NMR spectra of C?O of poly(di‐n‐butyl itaconate)s [poly(DBI)s] obtained at temperatures higher than 60 °C, although two kinds of carbonyl groups showed splittings due to triad tacticities in the spectra of polymers obtained at lower temperatures. The poly(DBI)s formed by the different kinds of initiators or formed in the presence of chain‐transfer agents showed hardly any changes in the intensities of the C resonances; this indicated that the C resonances were not due to the structures formed through initiating and terminating reactions. The poly(DBI)s obtained at different yields showed only a slight increase in the intensities of the C resonances with the yield, which suggested that the C resonances were not attributable to the intermolecular chain‐transfer reaction to the monomer and/or polymer. However, the intensities of the C resonances significantly increased with a decreasing feed monomer concentration; this suggested that intramolecular chain‐transfer reactions took place at high temperatures. Furthermore, a Cu complex‐catalyzed atom transfer radical polymerization mechanism was revealed to be effective for suppressing the intramolecular chain‐transfer reaction at 60 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2415–2426, 2002     

Block copolymer preparation by atom transfer radical polymerization under emulsion conditions using a nanoprecipitation technique

Living‐radical polymerization of acrylates were performed under emulsion atom transfer radical polymerization (ATRP) conditions using latexes prepared by a nanoprecipitation technique previously employed and optimized for the polymerization of styrene. A macroinitiator of poly(n‐butyl acrylate) prepared under bulk ATRP was dissolved in acetone and precipitated in an aqueous solution of Brij 98 to preform latex particles, which were then swollen with monomer and heated. Various monomers (i.e. n‐butyl acrylate, styrene, and tert‐butyl acrylate) were used to swell the particles to prepare homo‐ and block copolymers from the poly(n‐butyl acrylate) macroinitiator. Under these conditions latexes with a relatively good colloidal stability were obtained. Furthermore, amphiphilic block copolymers were prepared by hydrolysis of the tert‐butyl groups and the resulting block copolymers were characterized by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The bulk morphologies of the polystyrene‐b‐poly(n‐butyl acrylate) and poly(n‐butyl acrylate)‐b‐poly(acrylic acid) copolymers were investigated by atomic force microscopy (AFM) and small angle X‐ray scattering (SAXS). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 625–635, 2008     

Modeling and Experimentation of RAFT Solution Copolymerization of Styrene and Butyl Acrylate,Effect of Chain Transfer Reactions on Polymer Molecular Weight Distribution

Chain transfer reactions widely exist in the free radical polymerization and controlled radical polymerization, which can significantly influence polymer molecular weight and molecular weight distribution. In this work, the chain transfer reactions in modeling the reversible addition–fragmentation transfer (RAFT) solution copolymerization are included and the effects of chain transfer rate constant, monomer concentration, and comonomer ratio on the polymerization kinetics and polymer molecular weight development are investigated. The model is verified with the experimental RAFT solution copolymerization of styrene and butyl acrylate, with good agreements achieved. This work has demonstrated that the chain transfer reactions to monomer and solvent can have significant impacts on the number‐average molecular weight (M_n) and dispersity (Ð).     

Synthesis of poly(n‐butyl acrylate) containing multiblocks with a narrow molecular weight distribution using cyclic trithiocarbonates

The polymerization of n‐butyl acrylate in the presence of two cyclic trithiocarbonates (CTTCs) and the synthesis of multiblock poly(n‐butyl acrylate) have been investigated. The CTTCs not only can be stepwise incorporated into the polymer chain via reversible addition–fragmentation chain transfer (RAFT) but also can be polymerized into polytrithiocarbonate, which functions as a macro‐RAFT agent in turn. Through two kinds of mechanisms, multiblock poly(n‐butyl acrylate) containing narrow‐polydispersity blocks can be prepared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6600–6606, 2006     

Preparation of gradient copolymers via ATRP in miniemulsion. II. Forced gradient

A series of forced gradient copolymers with different controlled distribution of monomer units along the copolymer backbone were successfully prepared by atom transfer radical polymerization in miniemulsion. The newly developed initiation technique, known as activators generated by electron transfer, was beneficial for forced gradient copolymers preparation because all polymer chains were initiated within the miniemulsion droplets and the miniemulsion remained stable throughout the entire polymerization. Various monomer pairs with different reactivity ratios were examined in this study, including n‐butyl acrylate/t‐butyl acrylate, n‐butyl methacrylate/methyl methacrylate, and n‐butyl acrylate/styrene. In each case, the added monomer diffused across the aqueous suspending medium and gradient copolymers with different forced distributions of comonomer units along the polymer backbone were obtained. The shape of the gradient along the backbone of the copolymers was influenced by the molar ratio of the monomers, the reactivity ratio of the comonomers as well as the feeding rate. The shape of the gradient was also affected by the relative hydrophobicities of the comonomers. Copolymerizations exhibited good control for all feeding rates and comonomer feeding ratios, as evidenced by narrow molecular weight distribution (M_w/M_n = 1.20–1.40) and molecular weight increasing smoothly with polymer yield, indicating high initiation efficiency. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1413–1423, 2007     

Atom transfer radical polymerization of acrylates in an ionic liquid: Synthesis of block copolymers

Atom transfer radical polymerization (ATRP) of acrylates in ionic liquid, 1‐butyl‐3‐methylimidazolium hexaflurophospate, with the CuBr/CuBr₂/amine catalytic system was investigated. Sequential polymerization was performed by synthesizing AB block copolymers. Polymerization of butyl acrylate (monomer that is only partly soluble in an ionic liquid forming a two‐phase system) proceeded to practically quantitative conversion. If the second monomer (methyl acrylate) is added at this stage, polymerization proceeds, and block copolymer formed is essentially free of homopolymer according to size exclusion chromatographic analysis. The number‐average molecular weight of the copolymer is slightly higher than calculated, but the molecular weight distribution is low (M_w/M_n = 1.12). If, however, methyl acrylate (monomer that is soluble in an ionic liquid) is polymerized at the first stage, then butyl acrylate in the second‐stage situation is different. Block copolymer free of homopolymer of the first block (with M_w/M_n = 1.13) may be obtained only if the conversion of methyl acrylate at the stage when second monomer is added is not higher than 70%. Matrix‐assisted laser desorption/ionization time‐of‐flight analysis confirmed that irreversible deactivation of growing macromolecules is significant for methyl acrylate polymerization at a monomer conversion above 70%, whereas it is still not significant for butyl acrylate even at practically quantitative conversion. These results show that ATRP of butyl acrylate in ionic liquid followed by addition of a second acrylate monomer allows the clean synthesis of block copolymers by one‐pot sequential polymerization even if the first stage is carried out to complete conversion of butyl acrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2799–2809, 2002     

The Effect of Hydrogen Bonding on Intramolecular Chain Transfer in Polymerization of Acrylates

Propagation rate coefficients (k_p) for 2‐hydroxyethyl acrylate (HEA) have been determined by pulsed‐laser polymerization (PLP) combined with size‐exclusion chromatography (SEC) between 20 and 60 °C using pulse repetition rates of 50 and 100 Hz. The success of PLP–SEC under these conditions suggests that HEA is not subjected to the intramolecular chain transfer to polymer (backbiting) reactions dominant for other acrylates; ¹³C NMR analysis shows that the quaternary carbon observed in PLP‐generated poly(butyl acrylate) (pBA) samples is not observed in pHEA. These results are related to H‐bonding in the system, as it is shown that the introduction of H‐bonding by addition of n‐butanol to BA suppresses backbiting, and the disruption of H‐bonding by addition of dimethylformamide to HEA leads to an increased level of backbiting.

     

Influence of the isomeric structures of butyl acrylate on its single‐electron transfer‐degenerative chain transfer living radical polymerization in water Catalyzed by Na2S2O4

The aim of this work is to the study the influence of the isomer structures of butyl acrylate monomer on the single‐electron transfer/degenerative chain transfer mediated living radical polymerization (SET‐DTLRP). The kinetic of isobutyl acrylate is determined for the first time by SET‐DTLRP in water catalyzed by sodium dithionite. The plots of number‐average molecular weight versus conversion and ln([M]₀/[M]) versus time are linear, demonstrating a controlled polymerization. The influence of the isomer t‐butyl, i‐butyl, and n‐butyl on the kinetics, properties, and stereochemistry of the reactions was assessed. To the best of our knowledge, there is no previous report dealing with the synthesis of PiBA by any LRP approach in aqueous medium. The results presented in this work suggest that the stability provided by the acrylate side group has an important influence in the polymerization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6542–6551, 2008     

Reaction control in radical polymerization of di‐n‐butyl itaconate utilizing a hydrogen‐bonding interaction

We have reported that intramolecular chain‐transfer reaction takes place in radical polymerization of itaconates at high temperatures and/or at low monomer concentrations. In this article, radical polymerizations of di‐n‐butyl itaconate (DBI) were carried out in toluene at 60 °C in the presence of amide compounds. The ¹³C‐NMR spectra of the obtained poly(DBI)s indicated that the intramolecular chain‐transfer reaction was suppressed as compared with in the absence of amide compounds. The NMR analysis of DBI and N‐ethylacetamide demonstrated both 1:1 complex and 1:2 complex were formed at 60 °C through a hydrogen‐bonding interaction. The ESR analysis of radical polymerization of diisopropyl itaconate (DiPI) was conducted in addition to the NMR analysis of the obtained poly(DiPI). It was suggested that the suppression of the intramolecular chain‐transfer reaction with the hydrogen‐bonding interaction was achieved by controlling the conformation of the side chain at the penultimate monomeric unit of the propagating radical with an isotactic stereosequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4895–4905, 2004     

Living syndiospecific polymerization of propylene promoted by C1‐symmetric titanium complexes activated by dried MAO

A series of C₁‐symmetric titanium complexes with both salicylaldiminato and β‐enaminoketonato as the ligands have been synthesized and investigated as the catalysts for propylene polymerization. In the presence of dried methylaluminoxane (dMAO), the complex with bulky substituent tert‐butyl ortho to alkyl oxygen can promote living polymerization of propylene with improved catalytic activity at ambient temperature, producing high molecular weight syndiotactic polypropylenes (rrrr 90.2%) with narrow molecular weight distributions (M_w/M_n = 1.07–1.22), via a propagation of 1,2‐insertion of monomer and chain‐end control of stereoselectivity. The propagation of polymer chain is completely different from that mediated by FI catalysts (the titanium complexes with phenoxy‐imine chelate ligands) which favor 2,1‐insertion of monomer. The interaction between a fluorine and a β‐hydrogen of a growing polymer chain, negligible chain transfer to monomer and dMAO without any free AlMe₃ were responsible for the achievement of living propylene polymerization. The substituent ortho to alkyl oxygen determined the stereo structure of the resultant polypropylene. In the case of less steric congested complexes with two nonequivalent coordination positions, the growing polymer chain might swing back to the favorite coordination position (site‐epimerization), forming m dyads regioirregular units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of polynorbornene‐poly(tert‐butyl acrylate) nanoparticles with original morphologies by tandem ROMP and ATRP in microemulsion

Composite latex particles based on homopolymers and graft‐copolymers composed of polynorbornene (PNB) and poly(tert‐butyl acrylate) (PtBA) were synthesized in microemulsion conditions by simultaneous combination of two distinct methods of polymerization: Ring‐opening metathesis polymerization (ROMP) and atom transfer radical polymerization (ATRP). Only one commercial compound (first generation Grubbs catalyst) was used to initiate the ROMP of norbornene (NB) and activate the ATRP of tert‐butyl acrylate (tBA). Well‐defined nanoparticles with hydrodynamic diameters smaller than 50 nm were prepared with original morphologies depending on the monomer compositions, the type of combination (polymer blend or graft‐copolymer), and the conditions of microemulsion polymerizations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Polyolefin graft copolymers via living polymerization techniques: Preparation of poly(n‐butyl acrylate)‐graft‐polyethylene through the combination of Pd‐mediated living olefin polymerization and atom transfer radical polymerization

Poly(n‐butyl acrylate)‐graft‐branched polyethylene was successfully prepared by the combination of two living polymerization techniques. First, a branched polyethylene macromonomer with a methacrylate‐functionalized end group was prepared by Pd‐mediated living olefin polymerization. The macromonomer was then copolymerized with n‐butyl acrylate by atom transfer radical polymerization. Gel permeation chromatography traces of the graft copolymers showed narrow molecular weight distributions indicative of a controlled reaction. At low macromonomer concentrations corresponding to low viscosities, the reactivity ratios of the macromonomer to n‐butyl acrylate were similar to those for methyl methacrylate to n‐butyl acrylate. However, the increased viscosity of the reaction solution resulting from increased macromonomer concentrations caused a lowering of the apparent reactivity ratio of the macromonomer to n‐butyl acrylate, indicating an incompatibility between nonpolar polyethylene segments and a polar poly(n‐butyl acrylate) backbone. The incompatibility was more pronounced in the solid state, exhibiting cylindrical nanoscale morphology as a result of microphase separation, as observed by atomic force microscopy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2736–2749, 2002     

Mechanisms of n‐butanol formation in butyl acrylate latexes

The mechanisms involved in the formation of n‐butanol during the synthesis of butyl acrylate containing latices were investigated. The experimental results showed that neither the hydrolysis of butyl acrylate nor of the ester bond in the butyl acrylate segments of the polymer played a major role in the formation of n‐butanol, which was mainly generated from the polymer backbone, by transfer reactions to polymer chain followed by cyclization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5838–5846, 2007     

Single electron transfer–degenerative chain transfer living radical polymerization of N‐butyl acrylate catalyzed by Na2S2O4 in water media

Living radical polymerization of n‐butyl acrylate was achieved by single electron transfer/degenerative‐chain transfer mediated living radical polymerization in water catalyzed by sodium dithionate. The plots of number–average molecular weight versus conversion and ln[M]₀/[M] versus time are linear, indicating a controlled polymerization. This methodology leads to the preparation of α,ω‐di(iodo) poly (butyl acrylate) (α,ω‐di(iodo)PBA) macroinitiators. The influence of polymerization degree ([monomer]/[initiator]), amount of catalyst, concentration of suspending agents and temperature were studied. The molecular weight distributions were determined using a combination of three detectors (TriSEC): right‐angle light scattering (RALLS), a differential viscometer (DV), and refractive index (RI). The methodology studied in this work represents a possible route to prepare well‐tailored macromolecules made of butyl acrylate in an environmental friendly reaction medium. Moreover, such materials can be subsequently functionalized leading to the formation of different block copolymers of composition ABA. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2809–2825, 2006     

Atom Transfer Radical Polymerization with Polypeptide Initiators: A General Approach to Block Copolymers of Sequence‐Defined Polypeptides and Synthetic Polymers

Summary: A novel two‐step polymerization strategy allowing the integration of sequence‐defined oligopeptides into synthetic polymers has been demonstrated by the successful synthesis of an oligopeptide‐block‐poly(n‐butyl acrylate) copolymer. The approach utilizes a solid‐phase supported synthesis of an oligopeptide macroinitiator (SPPS) followed by solution‐phase atom transfer radical polymerization (ATRP) initiated by the oligopeptide macroinitiator. The resulting block copolymer exhibited a low (1.19) and a controllable .

Poly(n‐butyl acrylate)‐block‐oligopeptide.     

Atom transfer radical polymerization of n‐butyl acrylate from silica nanoparticles

This article reports the synthesis of atom transfer radical polymerization (ATRP) of active initiators from well‐defined silica nanoparticles and the use of these ATRP initiators in the grafting of poly(n‐butyl acrylate) from the silica particle surface. ATRP does not require difficult synthetic conditions, and the process can be carried out in standard solvents in which the nanoparticles are suspended. This “grafting from” method ensures the covalent binding of all polymer chains to the nanoparticles because polymerization is initiated from moieties previously bound to the surface. Model reactions were first carried out to account for possible polymerization in diluted conditions as it was required to ensure the suspension stability. The use of n‐butyl acrylate as the monomer permits one to obtain nanocomposites with a hard core and a soft shell where film formation is facilitated. Characterization of the polymer‐grafted silica was done from NMR and Fourier transform infrared spectroscopies, dynamic light scattering, and DSC. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4294–4301, 2001     

Kinetic studies on the n-alkyl acrylate polymerization

Kinetic studies on the polymerization of n-butyl acrylate and n-octadecyl acrylate in toluene at 70°C with benzoyl peroxide as initiator are reported. High monomer orders of 1.55 and 1.75 were obtained for n-butyl and n-octadecyl acrylates, respectively. Though the initiator order in butyl acrylate polymerization was 0.5, the octadecyl acrylate polymerization showed less than square root initiator order. The activation energy for the polymerization of both the acrylates was determined. Autoacceleration was found even at low conversions. The autoacceleration was influenced by both monomer and initiator concentration. Molecular weight data was presented in support of the gel effect. © 1992 John Wiley & Sons, Inc.     

Synthesis and characterization of block copolymers containing poly(di(ethylene glycol) 2‐ethylhexyl ether acrylate) by reversible addition–fragmentation chain transfer polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization has emerged as one of the important living radical polymerization techniques. Herein, we report the polymerization of di(ethylene glycol) 2‐ethylhexyl ether acrylate (DEHEA), a commercially‐available monomer consisting of an amphiphilic side chain, via RAFT by using bis(2‐propionic acid) trithiocarbonate as the chain transfer agent (CTA) and AIBN as the radical initiator, at 70 °C. The kinetics of DEHEA polymerization was also evaluated. Synthesis of well‐defined ABA triblock copolymers consisting of poly(tert‐butyl acrylate) (PtBA) or poly(octadecyl acrylate) (PODA) middle blocks were prepared from a PDEHEA macroCTA. By starting from a PtBA macroCTA, a BAB triblock copolymer with PDEHEA as the middle block was also readily prepared. These amphiphilic block copolymers with PDEHEA segments bearing unique amphiphilic side chains could potentially be used as the precursor components for construction of self‐assembled nanostructures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5420–5430, 2007     

Organosoluble star polymers from a cyclodextrin core

Well‐defined star polymers were synthesized with a combination of the core‐first method and atom transfer radical polymerization. The control of the architecture of the macroinitiator based on β‐cyclodextrin bearing functional bromide groups was determined by ¹³C NMR, fast atom bombardment mass spectrometry, and elemental analysis. In a second step, the polymerization of the tert‐butyl acrylate monomer was optimized to avoid a star–star coupling reaction and allowed the synthesis of a well‐defined organosoluble polymer star. The determination of the macromolecular dimensions of these new star polymers by size exclusion chromatography/light scattering was in agreement with the structure of armed star polymers in a large range of predicted molecular weights. This article describes a new approach to polyelectrolyte star polymers by postmodification of poly(tert‐butyl acrylate) by acrylic arm hydrolysis in a water‐soluble system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5186–5194, 2005