Influence of nozzle geometry on polystyrene degradation in convergent flow

Polymer degradation is readily observed in flows where the extensional component surpasses the rotational component of the velocity gradient. This type of flow is conveniently obtained by pushing a liquid into a convergent channel across an orifice. Kinetics of chain scission is sensitive to subtle modification of the coil conformation, which in turn depends on the details of the pervading flow field. By changing the orifice diameter and the conical angle of the inlet, it is possible to modify the spatial distribution of the velocity gradient, and hence, the residence time of a fluid element in the high strain-rate region. Degradation yields, measured under -conditions in decalin by Gel Permeation Chromatography, showed a strong dependence on the fluid velocity at the orifice, but not on the magnitude of the strain-rate. This result is contrary to the common belief that assumes viscous friction, proportional to the strain-rate, is the determining factor for the scission rate of a bond under stress. Rather, experimental findings tend to indicate that the driving force for chain scission was provided by the energy accumulated in the coil during the flow-induced deformation process. The sharp propensity for mid-chain scission was maintained regardless of the nozzle geometry.Dedicated to Prof. W. R. Pechhold on the occasion of his 60th birthday     

Temperature dependence of the non-Newtonian viscosity of elongated micellar solutions

We report in this work new results of the study on the non-Newtonian viscosity of aqueous micellar solutions of cetyltrimethylammonium bromide (CTAB) in the presence of potassium bromide (KBr), in the concentration range where the elongated micelles overlap. The experiments have been performed as a function of the surfactant concentration, temperature and shear rate by use of a Couette-viscosimeter.In the non-Newtonian range, at relatively low surfactant concentration (0.25 M/l), our results show that the flow curves obtained at different temperatures converge to a single liner curve with a characteristic slope varying with the surfactant concentration. These same data can be superposed on a master curve when appropriate reduced variables are used. The shape of the flow curves obtained at different temperatures for a sufficiently high surfactant concentration is similar to that obtained for monodisperse polymer solutions at different molecular weights. The slope obtained of about –1 is also predicted by Graessley's model in the theory of microviscoelasticity based on the concept of entanglement for polymer solutions. However, at surfactant concentration higher than 0.25 M/l our results show an unusual behavior. Above some critical shear rate it is possible to obtain an increase of the apparent viscosity with temperature. One possible explanation of this effect can be found in the increase of the entanglement with concentration coupled with the temperature and direct now effects on scission and recombination rate of the micelles.     

Estimation of the critical micelle concentrations and the aggregation numbers of sodium alkyl sulfates by capillary-type isotachophoresis

The analytical procedure for the separation and quantification of bulk and micellar phases for sodium alkyl sulfates has been investigated by a capillary-type isotachophoresis using a potential gradient detector. Monomer solutions were distinguished from micellar solutions at pH 5.5–6.0; hydrochloric acid — L-Histidine mixture was used as the leading electrolyte and 2-(N-Morpholino) ethanesulfonic acid as the terminating electrolyte.The potential unit value (PU value) due to the monomer solutions was larger than that due to the micellar solutions. The zone length due to monomer solutions increased with increasing concentration of surfactant until a given concentration (CMC); beyond this point the values became constant. On the other hand, the zone length due to micellar solutions increased from this point. We report an applicability of capillary-type isotachophoresis to determination of the CMC's and aggregation number for various sodium alkyl sulfates.     

Self-diffusion of polystyrene in solution 1. Experimental results of the NMR pulsed field gradient technique

We report self-diffusion measurements for polystyrene dissolved in benzene and chloroform using the NMR pulsed field gradient technique. The observed echo attenuations point to dynamic exchange processes or cluster formation in the semidilute solution. The experimental results are compared with theoretical predictions from the reptation mechanism and the blob theory. There is qualitative agreement, but a more comprehensive analysis of the data and results from experiments with polymer mixtures show that polymer self diffusion in semidilute solutions cannot be explained by the reptation mechanism in its simple form.     

Interfacial tension of gelatin/sodium dodecylsulphate solutions against air,toluene, and diethylphthalate

The adsorption isotherms between aqueous solutions of sodium dodecylsulphate and gelatin against air, toluene, or diethylphthalate were determined using the spinning drop method. The results qualitatively and quantitatively agreed with those found by surface tension measurements on sodium dodecylsulphate/gelatin solutions using the ring method in the version of Du Noüy. Interaction between gelatin and the surfactant will yield complexes which are more interfacially active than the components by themselves. The saturation of the interfaces occurs at lower concentrations than in solutions of the single components.     

CPS LG 315 Correlation between the phase behavior of ternary systems and removal of oil in the washing process

The correlation between the phase behavior of aqueous solutions of nonionic surfactants and the removal of oil from fabrics has been determined. Model washing experiments with pure and technical grade nonionic surfactants indicated that, in the dispersion ranges of liquid crystals, oil removal is substantially more temperature-dependent compared to micellar or surfactant liquid phases. In this phase region, interfacial tension does not seem to play a substantial role. The results are discussed in terms of the macroscopic properties of mesophases.The publications on which this report is based were promoted with funds of the Federal German Ministry of Research and Technology (No. 03 C 219 2). However, the authors alone are responsible for its contents.     

Equilibrium properties of ternary polymer solutions as explained by the renormalization group

In this paper we present a full account of renormalization group theory as applied to equilibrium properties of ternary polymer solutions containing two different polymer species and one solvent. We use a carefully constructed renormalization group mapping incorporating the screening effect by a proper choice of the renormalized segment size. The scaling functions reproducing observable quantities are calculated to tree approximation. We have evaluated a series of experiments on ternary solutions in this approximation and observe remarkably good agreement.     

Theoretical investigation of the segment-segment correlation in topological constrained networks

We study the influence of harmonic-like configurational constraints on the segment orientation correlation in polymer networks. The investigation uses the continuous Edwards-chain model. We show that all effects of the special chain model (as well as the constraints) are reflected by an intensive parameter in the distribution function of cos, where is the angle between a segment orientation and the fixed end-to-end distance vector of a network chain. In the case of vanishing constraints the second momentM ₂ yields the classical Kuhn-Gruen-result of the freely rotating chain. Starting with the phantom limit, the functionM ₂ first decreases with increasing constraints and increases by approaching the reference result in the case of strong constraints. Our results are compared with some experimental (²H NMR) findings.     

Physical gels from PVC: molecular structure of pregels and gels by low-angle neutron scattering

In this paper we report on investigations into the short-range molecular structure of pregels (aggregates formed in dilute solutions) and gels as a function of ageing time, temperature and solvent type. In some solvents (diethyl oxalate and bromobenzene) it is found that the structure of the pregels is cylinder-like or ellipsoid-like. The structure is seen to be the same for the gels and the pregels in the investigated range of transfer momentum which leads us to conclude that the gels are probably fiber-like, a statement in agreement with the morphology observed by Yang and Geil. The fiber section is also about the same order of magnitude as that reported by these authors. Also, further evidence is given for the existence of a second type of physical knot, different from those formed by the more syndiotactic sequences. The validity of the molecular structures deduced from these experiments is discussed in the light of macroscopic properties such as compression modulus and swelling.     

The behaviour of drag-reducing cationic surfactant solutions

The behaviour of two types of drag reducing surfactant solutions was studied in turbulent flows in pipes of different diameters. Our surfactant systems contained rod-like micelles; they consisted of equimolar mixtures ofn-tetradecyltrimethylammonium bromide,n-hexadecyltrimethylammonium bromide, and sodium salicylate. The structure of the turbulence was studied using a laser-Doppler anemometer in a 50 mm pipe. In the turbulent flow regime both surfactant solutions exhibited characteristic flow regimes. These flow regimes can be influenced by changing the amount of excess salt, the surfactant concentration, or the temperature. Shear viscosity measurements in laminar pipe and Couette flows show the occurrence of the so-called shear-induced state, where the viscosity increases and the surfactant solution becomes viscoelastic. The shape of the turbulent velocity profile depends on the flow regime. In the turbulent flow regime at low Reynolds numbers, velocity profiles similar to those observed for dilute polymer solutions are found, whereas at maximum drag reduction conditions more S-shaped profiles that show deviations from a logarithmic profile occur. An attempt is made to explain the drag reduction by rod-like micelles by combining the results of the rheological and the turbulence structure measurements.     

Crsslinking effect of ultrahigh molecular weight polyethylene-low molecular weight polyethylene blend films produced by gelation/crystallization from solutions

Polyethylene-polyethylene blend films were prepared by gelation/crystallization from semidilute solution by using ultrahigh molecular-weight (mw) polyethylene (UHMWPE) (mw=6×10⁶) and low molecular weight polyethylene (LMWPE) (mw=4×10⁴). The UHMWPE/LMWPE compositions chosen were 50/50, 67/33, and 91/9. Elongation was carried out in a hot oven at 115–130°C. The drawn films were exposed to an electron beam under nitrogen flow. Radiation doses chosen were 10, 20, 40, and 100 Mrad. crosslinking caused a significant effect in improving high temperature resistance for the blend film with draw ratio of 20 in the case of irradiation doses less than 20 Mrad. The elongation beyond 20 times and high doses beyond 20 Mrad hampered the crosslinking effect and the specimens were easily torn manually. This is thought to be due to the fact that the excess irradiation dose causes main chain scission apart from crosslinking.     

The spinnability of viscoelastic solutions of tetradecyl- and hexadecyl-trimethylammonium salicylates

The spinnability was measured for aqueous viscoelastic solutions of tetradecyl- and hexadecyltrimethylammonium salicylates (C₁₄TASal, C₁₆TASal) in the absence and presence of sodium salicylate (NaSal) and sodium bromide (NaBr). The spinnability is classified into two types, D and C. While the intrinsic drawing length in type D is proportional to the drawing velocity, the drawing intrinsic length in type C decreases with the drawing velocity or is independent of it. The spinnability changes from type D to C, as the drawing velocity and the surfactant concentration increase, and the temperature lowers. The effect of salt is different between NaSal and NaBr. It can be assumed that a pseudo-network structure composed of rod-like micelles is formed in viscoelastic and spinnable surfactant solutions. Then, the spinnability depends on the balance between the elasticity and the viscosity in which the structure results.     

Role of ionic species and valency on the steady shear behavior of partially hydrolyzed polyacrylamide solutions

Polyacrylamides are anionic polymers with a large number of charges along the polymer chains. The rheological properties of aqueous polyacrylamide solutions can be significantly modified by varying the solvent environment with the addition of salt. The presence of cations substantially reduces the inter- and intra-molecular interactions of the macroions. It was found that the valency of the cation has a strong effect on the rheological behavior of polyacrylamide solutions, but the size and type of salt have a negligible effect.The reduction in the solution viscosity with di-valent salts (e.g., CaCl₂, MgCl₂, BaCl₂, and MgSO₄) can be as high as an order of magnitude compared with mono-valent salt (KI, KC1, NaCl, and NaBr), depending on the salt concentration and shear rate. An identical viscosity function can be obtained for different types of polyacrylamide solutions by varying the salt content in solution. This interesting feature provides a useful means in the development and preparation of certain ideal fluids for simulation studies of complex flow problems.     

The influence of surfactants on the structure of transparent gelatin films

The interference image of cold-dried transparent gelatin films containing different surfactants was determined in the conoscopic ray of monochromatic light. From the results obtained the order of the structure of gelatin in the film was characterized. Unlike the ionic surfactants (sodium dodecyl sulfate and hexadecyltrimethyl ammonium bromide), which lead to a reduction of the ordered structure, the addition of nonionic and amphoteric surfactants [ethoxylized octylphenole and a technical C₁₂/C₁₄-dipoly(oxyethylene)ammoniopropane sulfonate] causes an increase of the ordered structure of gelatin. The results quantitatively agree with those found for the influence of surfactants on the secondary structure of gelatin in diluted gelatin solutions. The influence is independent of the gelatin/surfactant ratio and has been explained by gelatin/gelatin interaction competing with the gelatin/surfactant interaction if the gelatin concentration becomes sufficiently high.     

Study of the thermodynamics of adsorption of hydrolyzed modified polyacrylnitrile

The thermodynamics of adsorption has been studied of hydrolyzed modified polyacrylnitrile (HMP) in water solutions with a concentration ranging from 0.25 g/l to 2.00 g/l on bleached sulphate and unbleached and bleached sulphite celluloses at temperatures of 0, 20, 40, and 60 C.It has been established that with the rise in temperature, the amount of adsorbed polymer —(HMP) decreases. The values of the enthalpy change are negative and show a linear decrease with the increase in the amount of adsorbed polymer. The adsorption equilibrium is defined by the logarithmic isotherm of Tjumkin, valid for uniform heterogeneous surfaces.With the increase in the amount of adsorbed HMP the values of the entropy change become negative and linearly decrease. A compensation effect has been noticed which results from the simultaneous action of the entropy and energy factors.The values of the change of the chemical potential for the three types of cellulose are negative and linearly decrease with the increase in the amount of adsorbed HMP and with the rise in temperature.     

Characteristics of rodlike micelles of cetyltrimethylammonium chloride in aqueous NaCl solutions: Their flexibility and the scaling laws in dilute and semidilute regimes

Static light scattering has been measured for aqueous NaCl solutions of cetyltrimethylammonium chloride (CTAC) at 25 °C. While spherical micelles are formed above the critical micelle concentration for 0–1.5 M NaCl solutions, rodlike micelles are formed at NaCl concentrations higher than 1.18 M.The aggregation number of rodlike micelles increases markedly with increasing NaCl concentration, and it is as large as 11400 in 4.0 M NaCl. Long rodlike micelles are semiflexible and behave like wormlike chains. Their contour length and persistence length have been calculated as 630 and 46.4 nm, respectively, in 4.0 M NaCl.Rodlike micelles overlap and entangle together to form a network in semidilute solutions above a threshold micelle concentration. The radius of gyration of the blob can be scaled for its molecular weight with the exponent, 0.55, coinciding with that for isolated rodlike micelles in dilute solutions. The scaling laws for the reciprocal envelope of light scattered in the semidilute regime and for the molecular weight and the radius of gyration of the blob are also discussed with reference to the micelle concentration.     

Conductivity of alkaline earth metal soaps in methanol

The conductance of the solution of calcium, strontium and barium butyrates in methanol has been measured at 35–50 °C (± 0.05 °C) in order to determine the CMC, dissociation constant, molecular conductance at infinite dilution, and thermodynamic parameters viz. enthalpy, free energy, entropy changes for both dissociation and association processes. The results show that these soaps behave as a weak electrolyte in methanol and Debye-Huckel-Onsager's equation is not applicable to the solutions of these soaps.     

Fluorescence and viscometry study of complexation of poly(acrylic acid) with poly(acrylamide) and hydrolysed poly(acrylamide)

Interpolymer complexation of poly(acrylic acid) with poly(acrylamide) and hydrolysed poly(acrylamide) was studied by fluorescence spectroscopy and viscometry in dilute aqueous solutions. Changes in chain conformation and flexibility due to the interpolymer association are reflected in the intramolecular excimer fluorescence of pyrene groups covalently attached to the polymer chain. Both poly(acrylamide) and hydrolysed poly(acrylamide) form stable complexes with poly(acrylic acid) at low pH. The molecular weight of poly(acrylic acid) and solution properties such as pH and ionic strength were found to influence the stability and the structure of the complexes. In addition, the polymer solutions mixing time showed an effect on the mean stoichiometry of the complex. The intrinsic viscosity of the solutions of mixed polymers at low pH suggested a compact polymer structure for the complex.     

The viscoelasticity of spinnable solutions of alkyltrimethylammonium salicylates

The viscoelasticity has been measured for aqueous solutions of tetradecyl-and hexadecyltrimethylammonium salicylates (C₁₄TASal, C₁₆TASal). The aqueous solutions of C₁₄TASal without salt displayed the gel-like behavior at 10.0×10^–2 g cm^–3, but those more dilute than 3.2×10^–2 g cm^–3 presented the viscoelasticity similar to that of a Maxwell liquid. The Maxwell-like behavior was converted to the polymer-like one on the addition of (0.1–0.2) M NaBr or (0.02–0.2) M NaSal. The gel-like viscoelasticity can be connected with the spinnability of cohesive fracture failure, and the Maxwell-like and polymer-like viscoelasticities are concerned with the spinnability of ductile failure. The gel-like and Maxwell-like viscoelasticities originate in the pseudo-network formed by the pseudo-linkages between rodlike micelles, while the polymer-like viscoelasticity is caused by the entanglement of long rodlike micelles in semidilute and concentrated solutions. The aqueous solutions of C₁₆TASal behaved very similar to those of C₁₄TASal.