Magnetic and magnetoresistive properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–Sr<Subscript>2</Subscript>FeMoO<Subscript>6–δ</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoheterostructures

A method has been developed for fabricating nanoporous matrices based on anodic aluminum oxide for the deposition of ferromagnetic nanoparticles in them. The modes of deposition of strontium ferromolybdate thin films prepared by the ion-plasma method have been worked out, and the magnetic and magnetoresistive properties, structure, and composition of the films have been investigated. It has been revealed that the microstructure and properties of the strontium ferromolybdate films deposited by ionplasma sputtering depend on the deposition rate and the temperature of the substrate. Based on the measurement of the electrical resistivity of nanoheterostructures in a magnetic field, it has been found that the magnetoresistance reaches 14% at T = 15 K and B = 8 T, which is due to the manifestation of tunneling magnetoresistance.     

Electrical switching in the MoO<Subscript>3</Subscript>–WO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> and MoO<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

High field electrical switching on blown films of MoO₃(60%)–P₂O₅(40%), MoO₃(50%)–WO₃(10%)–P₂O₅(40%), and MoO₃(45%)–WO₃(15%)–P₂O₅(40%) having different thicknesses was studied and compared. Switching was observed using two terminal samples. S-type current–voltage characteristic (current-controlled negative resistance—CCNR) with memory was observed in molybdenum–phosphate glasses, but N-type characteristic (voltage-controlled negative resistance—VCNR) with threshold in tungsten–molybdenum–phosphate glasses was observed. The important observation was that with the addition of WO₃ to binary MoO₃–P₂O5 led to a change of I–V characteristic from CCNR with memory to VCNR with threshold. The measurements of density and molar volume showed linear relation between MoO₃ content and density which decreased with the increase of MoO₃ content. The samples’ thickness had no significant effect on threshold voltage. The attained results also indicated that the electrode material had no effect on switching property of devices. The switching behavior of the devices did not show any dependence on the polarity of the applied voltage. In terms of the effect of heat on the switching behavior of molybdenum–phosphate glasses, it was found that threshold voltage decreases with increasing of temperature. Finally, the switching phenomenon was explained by thermal (formation of crystalline filaments) and electronic models.     

Elastic properties of TeO<Subscript>2</Subscript>–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–Ag<Subscript>2</Subscript>O glasses

A series of glasses [(TeO₂) _x (B₂O₃)_1−x ]_1−y [Ag₂O] _y with x = 70 and y = 10, 15, 20, 25 and 30 mol% were synthesised by rapid quenching. Longitudinal and shear ultrasonic velocity were measured at room temperature and at 5 MHz frequency. Elastic properties, Poisson's ratio, microhardness, softening temperature and Debye temperature have been calculated from the measured density and ultrasonic velocity at room temperature. The experimental results indicate that the elastic constants depend upon the composition of the glasses and the role of the Ag₂O inside the glass network is discussed. Estimated parameters based on Makishima–Mackenzie theory and bond compression model were calculated in order to analyse the experimental elastic moduli. Comparison between the experimental elastic moduli data obtained in the study and the calculated theoretically by the mentioned above models has been discussed.     

Sol–gel synthesis and characterization of Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite solid electrolytes

Composite solid electrolytes in the system (1???x)Li₂CO₃–xAl₂O₃, with x?=?0.0–0.5 (mole), were synthesized by a sol–gel method. The synthesis carried out at low temperature resulted in voluminous and fluffy products. The obtained materials were characterized by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy/energy-dispersive X-ray, Fourier transform infrared spectroscopy and AC impedance spectroscopy. Structural analysis of the samples showed an amorphous feature of Li₂CO₃ and traces of α-LiAlO₂, γ-LiAlO₂ and LiAl₅O₈. The prepared composite samples possess high ionic conductivities at 130–180 °C on account of the presence of lithium aluminates as well as the formation of a high concentration of an amorphous phase of Li₂CO₃ via this sol–gel preparative technique.     

High-Temperature Heat Capacity of Zn<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>–Cu<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript> Solid Solutions

Differential scanning calorimetry has been used to study the influence of temperature on the heat capacity of synthesized vanadates Zn₂V₂O₇, (Cu_0.56Zn_1.44)V₂O₇, and (Cu_1.0Zn_1.0)V₂O₇. It is found that dependences C_p = f(T) have extremes. The thermodynamic properties of Zn₂V₂O₇ have been determined.     

Deep metastable eutectic nanometer-scale particles in the MgO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

Laboratory vapor phase condensation experiments systematically yield amorphous, homogeneous, nanoparticles with unique deep metastable eutectic compositions. They formed during the nucleation stage in rapidly cooling vapor systems. These nanoparticles evidence the complexity of the nucleation stage. Similar complex behavior may occur during the nucleation stage in quenched-melt laboratory experiments. Because of the bulk size of the quenched system many of such deep metastable eutectic nanodomains will anneal and adjust to local equilibrium but some will persist metastably depending on the time–temperature regime and melt/glass transformation.     

O<Subscript>2</Subscript> photodesorption from AuO<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack> and Au<Subscript>2</Subscript>O<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack>

Using time-resolved photoelectron spectroscopy, the decay channels of AuO₂⁻ and Au₂O₂⁻ following photoexcitation with 3.1-eV photons have been studied. For AuO₂⁻, a state with a rather long lifetime of 30 ps has been identified. Its decay path could not be determined but photodesorption can be excluded. For Au₂O₂⁻, the spectra indicate O₂ desorption after 3.1-eV photoexcitation on a time scale of 1 ps. While comparing these results on Au _n O₂⁻ with analogous data on Ag _n O₂⁻ clusters, a discernible pattern emerges: for dissociatively bound O₂(AuO₂⁻, Ag₃O₂⁻), there are long-living excited states which do not decay by oxygen desorption, while for molecular chemisorption (Au₂O₂⁻, Ag₂O₂⁻, Ag₄O₂⁻, Ag₈O₂⁻), the 3.1-eV photoexcitation triggers fast O₂ desorption with a high quantum yield.     

Study of the KNO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system by differential scanning calorimetry

The structural and the thermodynamic properties of potassium nitrate KNO₃ and its composites with nanosized aluminum oxide Al₂O₃ have been studied by differential scanning calorimetry. It has been found that an amorphous phase forms in composites (1–x)KNO_3–xAl₂O₃. The thermal effect corresponding to this phase has been observed at 316°C. It has been found that the phase transition heats of potassium nitrate decreased as the aluminum oxide fraction increased.     

Microwave dielectric properties of the 5.5Li<Subscript>2</Subscript>O–Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>–7TiO<Subscript>2</Subscript> ceramics

A new Li₂O–Nb₂O₅–TiO₂ (LNT) ceramic with the Li₂O:Nb₂O₅:TiO₂ mole ratio of 5.5:1:7 was prepared by solid state reaction route. The phase and structure of the ceramic were characterized by X-ray diffraction and scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The microwave dielectric ceramic has low sintering temperature (∼1075°C) and good microwave dielectric properties of ε _r=42, Q×f=16900 GHz (5.75 GHz), and τ _f =63.7 ppm/°C. The addition of B₂O₃ can effectively lower the sintering temperature from 1075 to 875°C and does not induce degradation of the microwave dielectric properties. Obviously, the LNT ceramics can be applied to microwave low temperature-cofired ceramics (LTCC) devices.     

Dielectric response of SrTiO<Subscript>3</Subscript>–SrMg<Subscript>1/3</Subscript>Nb<Subscript>2/3</Subscript>O<Subscript>3</Subscript> solid solutions in the terahertz–infrared range

The reflection and transmission spectra of ceramic samples of SrTiO₃–SrMg_1/3Nb_2/3O₃ solid solutions have been measured in the frequency range of 5–5000 cm^–1 and in the temperature range of 5–370 K. Based on these spectra, the spectra of the real ε'(ν) and imaginary ε''(ν) parts of the complex permittivity ε*(ν) have been simulated by the method of dispersion analysis. It has been found that the temperature evolution of the dielectric constant is entirely determined by the behavior of the soft mode.     

Influence of Matrix Nature on the Structural Characteristics of In<Subscript>2</Subscript>O<Subscript>3</Subscript>–CeO<Subscript>2</Subscript> and SnO<Subscript>2</Subscript>–CeO<Subscript>2</Subscript> Composites Fabricated by the Impregnation Method

The structural characteristics, valence states, and distribution of cerium ions between the components in In₂O₃–CeO₂ and SnO₂–CeO₂ nanocomposites fabricated using the impregnation method were studied. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were used to show that, during impregnation, cerium ions are not included into In₂O₃ crystals and are disposed only on their surface in the form of nano-sized crystallites or amorphous clusters. On the other side, under the contact of CeO₂ clusters with a surface of SnO₂ matrix crystals, cerium ions penetrate into the surface layer of these crystals. In contrast to an In₂O₃–CeO₂ system, where the addition of CeO₂ does not affect the conduction activation energy, where cerium oxide is added to SnO₂, the observed increase in the resistance of a SnO₂–CeO₂ composite is accompanied by a sufficient increase in activation energy. These data and the XPS spectra confirm the modification of the surface layers of conductive SnO₂ crystals as, a result of the penetration of cerium ions into these layers.     

AC Conductivity,XRD and transport properties of melt quenched PbI<Subscript>2</Subscript>–Ag<Subscript>2</Subscript>O–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Composite materials used for electrode and electrolyte materials have been intensely studied in view of their advantages such as higher conductivity and better operational performance compared to their single-phase counterparts. The present work aims at studying the electrical and structural characteristics of a new composite electrolyte namely, (PbI₂) _x  − (Ag₂O–Cr₂O₃)_100−x where x = 5, 10, 15, 20, and 25 mol%, respectively, prepared by the melt quenching technique. The room temperature X-ray diffraction spectra revealed certain crystalline phases in the samples. AC conductivity analysis for all the prepared samples was carried out over the frequency range 1 MHz–20 Hz and in the temperature window 297–468 K. The room temperature conductivity values were calculated to be in the order of 10⁻⁵–10⁻³ Scm⁻¹. An Arrhenius dependence of temperature with conductivity was observed, and the activation energies calculated were found to be in the range 0.27–0.31 eV. Furthermore, the total ionic transport number (t _i) values obtained for all these indicated the ionic nature of this system. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Particle speciation during PEG–Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> hybrid nanoparticle self-assembly on Si(Ti)O<Subscript>2</Subscript>

The kinetics of assembly of polyethylene glycol (PEG)-coated superparamagnetic Fe₃O₄ nanoparticles in aqueous suspension on planar Si(Ti)O₂ surfaces have been determined using high-resolution optical waveguide lightmode spectroscopy (OWLS). Analysis of the results revealed that the initially uniform population was spontaneously transformed into two types of particles with significantly different adsorption behaviour.     

KF-doped BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> ferroelectric ceramics by solid-state reaction of KF and sol–gel-derived BaTi<Subscript>2</Subscript>O<Subscript>5</Subscript> powders

We report KF-doping work on the recently found ferroelectric material BaTi₂O₅. The ceramic samples, Ba_1-xK_xTi₂O_5-xF_x, were synthesized by solid-state reaction of mixed KF and sol–gel-derived BaTi₂O₅ powders at 1150 °C. An almost pure phase was obtained for nominal composition x≤0.097, while electron probe microanalysis indicated that the real incorporated K and F contents were less than half of the nominal values. It was observed that KF-doping is beneficial in enhancing the ceramic density to some extent, which is a key issue in sol–gel-derived BaTi₂O₅ ceramics, due to a possible liquid-phase sintering mechanism through the presence of melted KF at the sintering temperature. Scanning electron microscopy images showed that these porous ceramic samples are composed of sub-micron-sized powder aggregates which, with increasing KF-doping, undergo further agglomeration. Dielectric measurement from room temperature to ∼ 560 °C showed a broad ferroelectric phase transition, with T_C ∼ 430 °C for the undoped sample. As KF-doping increases, T_C decreases, and the magnitude of the dielectric constant maximum also displays a decreasing trend. The strongly reduced dielectric response can be partly understood by regarding the porous ceramic sample as a composite material composed of bulk BaTi₂O₅ and air, where the porosity has a significant influence on the effective dielectric constant. PACS 77.84.-s; 77.84.Dy; 81.20.Fw     

Luminescence centers in α-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics

Luminescence photoexcitation spectra of α-Bi₂O₃ ceramics are investigated. Luminescence spectra were deconvoluted into fundamental components using the Alentsev-Fok method. It is established that the luminescence spectra of α-Bi₂O₃ ceramics consist of three fundamental bands with maxima at 2.75, 2.40, and 1.97 eV. A comparison of the results with those from an investigation of luminescence of various modifications of bismuth oxide and bismuth germanates suggests that luminescence of these compounds is caused by radiation processes that occur in structural complexes that contain the bismuth ion in a nearest oxygen environment. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 5, pp. 672–676, September–October, 2008.     

Synthesis of cubic Li<Subscript>7</Subscript>La<Subscript>3</Subscript>Zr<Subscript>2</Subscript>O<Subscript>12</Subscript> by modified sol–gel process

Polycrystalline cubic Li₇La₃Zr₂O₁₂ (LLZ) with garnet-related type structure has been synthesized at 700 °C by modified sol–gel processes using citric acid as organic complexing agent and butan-1-ol or propan-2-ol as surface active agent. Thermal analysis (thermogravimetric/differential thermal analysis) indicated that the gel must be annealed at around 700 °C to completely remove the organic solvent. X-ray powder diffraction, X-ray fluorescence, and scanning electron microscopic investigations revealed that Al may not be essential to form cubic-phase LLZ; however, the addition of Al₂O₃ led to enhanced sintering of LLZ.     

μSR study of Eu<Subscript>0.8</Subscript>Ce<Subscript>0.2</Subscript>Mn<Subscript>2</Subscript>O<Subscript>5</Subscript> and EuMn<Subscript>2</Subscript>O<Subscript>5</Subscript> multiferroics

A comparative μSR study of ceramic samples of the EuMn₂O₅ and Eu_0.8Ce_0.2Mn₂O₅ multiferroics is performed in the temperature range from 15 to 300 K. It is found that the Ce doping of the EuMn₂O₅ sample slightly reduces the temperature of the magnetic phase transition from T _N = 45 K for the EuMn₂O₅ sample to T _N = 42.5 K for the Eu_0.8Ce_0.2Mn₂O₅ sample. Below the temperature T _N for both samples, there are two types of localization of a thermalized muon with different temperature dependences of the precession frequency of the magnetic moment of the muon in an internal magnetic field. The higher frequency in both samples refers to the initial antiferromagnetic matrix. The behavior of this frequency in Eu_0.8Ce_0.2Mn₂O₅ follows the Curie–Weiss law with the exponent β = 0.29 ± 0.02, which differs from the value β = 0.39 standard for 3D Heisenberg magnetics and is observed in EuMn₂O₅, because of the strong frustration of the doped sample. The temperature-independent low frequency is due to the presence of Mn³⁺–Mn⁴⁺ ferromagnetic pairs located along the b axis of the antiferromagnetic matrix and in the regions of phase separation, which contain such ion pairs and e _g electrons recharging them. In both samples, polarization losses are the same (about 20%) and are associated with the formation of Mn⁴⁺–Mn⁴⁺ + Mu complexes near Mn³⁺–Mn⁴⁺ ferromagnetic pairs. In the temperature interval from 25 to 45 K, the separation of the Eu_0.8Ce_0.2Mn₂O₅ structure into two fractions where the relaxation rates of polarization of muons differ by an order of magnitude is revealed. This effect is due to a change in the state of regions of phase separation (1D superlattices) at the indicated temperatures. Such effect in EuMn₂O₅ is significantly weaker.     

Metal–insulator phase transition in hydrogenated thin films of V<Subscript>2</Subscript>O<Subscript>3</Subscript>

Temperature dependences of the electrical conductivity of thin vanadium sesquioxide V2O3 films obtained by using the laser sputtering technique have been studied. A significant decrease (by four–five orders of magnitude) in the electrical conductivity has been observed below 150 K as a result of a metal–insulator phase transition. It is shown that hydrogenation of films lowers the temperature of this phase transition.     

Effect of mixed glass formers on the crystallization kinetics in AgI–Ag<Subscript>2</Subscript>O–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–MoO<Subscript>3</Subscript> glassy superionic system

The crystallization and glass transition kinetics using differential scanning calorimetry (DSC) in 50AgI–33.33Ag₂O–16.67[(V₂O₅)_1−x –(MoO₃) _x ] superionic glassy system is discussed. Thermal stability of glass, studied using various criteria, does not vary significantly with glass former variation. However, the activation energies for structural relaxation (E _s) at glass transition temperature and crystallization (E _c) obtained using Moynihan and Kissinger, Matusita-Sakka formulations found to exhibit interesting trends with MoO₃ substitution in the glass matrix. It is noticed that the electrical conductivity (σ)–temperature (T) cycles obtained at a typical heating rate of 1 °C/min do exhibit significant thermal events. The conductivity after first heating cycle at room temperature is found to be increasing with MoO₃ content and maximum for x = 0.3 (~10⁻³ Ω⁻¹ cm⁻¹ at 30 °C) which is comparable to that of the host 50AgI–33.33Ag₂O–16.67V₂O₅ glassy system. The parameters obtained from σ–T plots and DSC scans do complement each other in a particular range of composition.