Washing effects on the anchoring energy and surface order parameter on rubbed polymer surfaces containing the trifluoromethyl moiety

The washing effects on liquid crystal (LC) alignment capability in a NLC, 4-n-pentyl-4'-cyanobiphenyl (5CB), on a rubbed polyimide (PI) surface containing the trifluoromethyl moiety were studied. The extrapolation length d_e of 5CB on the rubbed PI surface decreases with the rubbing strength RS. Also, the large extrapolation length d_e of 5CB for washing with IPA was measured at RS=114 mm. The polar anchoring energy of 5CB on the rubbed PI surface was decreased by the washing process; it increased with the rubbing strength RS on the PI surface. The surface order parameter S_S of 5CB for all the washing processes is smaller than for the non-washing process. Consequently, the polar anchoring energy and surface order parameter S_s in 5CB are largely attributed to washing effects.     

Synthesis of a liquid crystalline azobenzene monomer for photoalignment of ferroelectric liquid crystals

A liquid crystalline dimethacrylate-based monomer containing an azobenzene group was synthesized. The miscibility of the azo monomer and its crosslinked polymer network with ferroelectric liquid crystals (FLCs) was improved by the liquid crystallinity of the monomer. By performing thermal polymerization of the azo monomer dissolved in a FLC host under linearly polarized visible light irradiation, following a pre-irradiation with unpolarized UV light at room temperature, bulk alignment of the FLC could be induced in the absence of surface orientation layers, as a result of the photo-orientation of azobenzene moieties related to the reversible trans-cis photoisomerization of the chromophore. The optical and rubbing-free alignment of a FLC could be achieved with as few as 0.5 wt % of the azo polymer network. This represents a step toward the preparation of uniform samples of photoaligned FLC by reducing the amount of the azo polymer network that may be phase-separated from the FLC host.     

Photoreactive main‐chain liquid‐crystalline polyesters: Synthesis,characterization, and photochemistry

Three series of semiflexible and rigid main‐chain polyesters containing photoreactive mesogenic units derived from p‐phenylenediacrylic acid (PDA) and cinnamic acid have been synthesized by high‐temperature polycondensation. The thermal and mesomorphic properties of the polymers have been determined. The photochemical behavior of polymer P‐[1]‐T, which contains a PDA unit, has been studied both in solution and in films. In solution, [2+2] photocycloaddition, E/Z photoisomerization, and photo‐Fries rearrangement can take place. In contrast, the dominant process in spin‐coated films is the [2+2] photocycloaddition reaction, which causes crosslinking of the polymer. In films, the photochemistry and induction of anisotropy are strongly influenced by the aggregation of the PDA phenylester unit. A dichroism of about 0.2 has been induced in films by irradiation with linearly polarized UV light, and thus the capability of these films to induce optical anisotropy and align liquid crystals has been demonstrated. Liquid‐crystalline cells have been made with polarized irradiated films of P‐[1]‐T as aligning layers. A commercial liquid‐crystalline mixture has been used for this study, and a similar liquid‐crystalline order determined by polarized Fourier transform infrared to a commercial cell with rubbed polyimide as an aligning layer has been detected. Because of crosslinking of the irradiated P‐[1]‐T photoaligning layer, the photoinduced anisotropy is stable at high temperatures, and the liquid‐crystalline molecules are insoluble in the irradiated polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4907–4921, 2005     

Zigzag defect-free alignment of surface stabilized ferroelectric liquid crystal cells with a polyimide irradiated by polarized UV light

Zigzag defect-free surface stabilized ferroelectric liquid crystal (SSFLC) cells were prepared using a photodegradable polyimide (PI) having a cyclobutane ring in the backbone. The PI layers were irradiated by polarized ultraviolet light (PUVL) at normal incidence to the surface, and characterized by UV and FTIR spectroscopy. The anisotropy originates from preferential cleavage of PI chains oriented parallel to the polarization direction of the irradiating PUVL. After the polarized UV light irradiation, the PI surface was much flatter than that after rubbing, but it induced a similar order parameter of dye-doped nematic LC molecules to that for a rubbed cell. Alignment of both the FLC molecules and the layer structure is important in SSFLC. After 40 min irradiation, the FLC molecules were well aligned homogeneously, and the FLC cells showed a uniform texture without zigzag defects which also indicates a well aligned layer structure. Zigzag defect-free alignment may result from the flatter surface, the much smaller and more constant pretilt angles, and the bigger cone angle than those achieved by rubbing.     

Zigzag defect-free alignment of surface stabilized ferroelectric liquid crystal cells with a polyimide irradiated by polarized UV light

Zigzag defect-free surface stabilized ferroelectric liquid crystal (SSFLC) cells were prepared using a photodegradable polyimide (PI) having a cyclobutane ring in the backbone. The PI layers were irradiated by polarized ultraviolet light (PUVL) at normal incidence to the surface, and characterized by UV and FTIR spectroscopy. The anisotropy originates from preferential cleavage of PI chains oriented parallel to the polarization direction of the irradiating PUVL. After the polarized UV light irradiation, the PI surface was much flatter than that after rubbing, but it induced a similar order parameter of dye-doped nematic LC molecules to that for a rubbed cell. Alignment of both the FLC molecules and the layer structure is important in SSFLC. After 40 min irradiation, the FLC molecules were well aligned homogeneously, and the FLC cells showed a uniform texture without zigzag defects which also indicates a well aligned layer structure. Zigzag defect-free alignment may result from the flatter surface, the much smaller and more constant pretilt angles, and the bigger cone angle than those achieved by rubbing.     

Photoinduced anchoring transitions in a nematic doped with azo dyes

Recently, we reported on a light-induced anchoring transition of an azobenzene nematic from planar to homeotropic alignment. In the proposed model of the transition, the changes in shape of the liquid crystal molecules and of their net dipole moment, due to the photoisomerization, were considered to play a vital role in the occurrence of the transition. In order to assess the validity of this model, a study of the anchoring behaviour of nematic guest-host liquid crystal mixtures containing two photochromic dyes, 3,3'- and 4,4'-substituted azobenzenes, was carried out. The dyes have very similar molecular structures to that of the azobenzene nematic previously studied, and their molecules, having a linear shape in the trans-form, maintained this shape after photoisomerization in the case of the 3,3'-azo dye, and changed it to bent in the case of the 4,4'-azo dye. The dyes possessed similar net dipole moments that increased substantially after photoisomerization, resulting in a preferential adsorption of their cis-isomers on the solid substrate. However, only the mixture containing the 4,4'-azo dye exhibited an anchoring transition from planar to homeotropic alignment upon illumination with unpolarized UV light, a behaviour in excellent agreement with the prediction of the model for the light-induced anchoring transition. An anchoring transition from random planar to uniform planar alignment was found to take place in the mixtures when linearly polarized UV light was used, requiring, however, a different exposure time for the two dyes.     

Photoinduced anchoring transitions in a nematic doped with azo dyes

Recently, we reported on a light-induced anchoring transition of an azobenzene nematic from planar to homeotropic alignment. In the proposed model of the transition, the changes in shape of the liquid crystal molecules and of their net dipole moment, due to the photoisomerization, were considered to play a vital role in the occurrence of the transition. In order to assess the validity of this model, a study of the anchoring behaviour of nematic guest-host liquid crystal mixtures containing two photochromic dyes, 3,3'- and 4,4'-substituted azobenzenes, was carried out. The dyes have very similar molecular structures to that of the azobenzene nematic previously studied, and their molecules, having a linear shape in the trans-form, maintained this shape after photoisomerization in the case of the 3,3'-azo dye, and changed it to bent in the case of the 4,4'-azo dye. The dyes possessed similar net dipole moments that increased substantially after photoisomerization, resulting in a preferential adsorption of their cis-isomers on the solid substrate. However, only the mixture containing the 4,4'-azo dye exhibited an anchoring transition from planar to homeotropic alignment upon illumination with unpolarized UV light, a behaviour in excellent agreement with the prediction of the model for the light-induced anchoring transition. An anchoring transition from random planar to uniform planar alignment was found to take place in the mixtures when linearly polarized UV light was used, requiring, however, a different exposure time for the two dyes.     

Influence of the washing process on the aligning capability of a nematic liquid crystal on polymer surfaces

The influence of washing processes on the liquid crystal (LC) aligning capability on rubbed polyimide (PI) surfaces containing the CONH moiety were investigated. The induced optical retardation from a non-washing process on a rubbed PI surface is larger than when the washing processes are included. The pretilt angles in 4-n-pentyl-4'-cyanobiphenyl (5CB) were decreased by the washing process. The polar anchoring energy of 5CB was decreased by the washing processes on a weakly rubbed PI surface. The surface order parameter S_S of 5CB strongly depends on the rubbing strength and washing materials. Consequently, the LC aligning capability may be strongly attributed to the polymer characteristics and the washing processes.     

Photo‐aligning of polyimide layers for liquid crystals

A series of soluble and highly transparent semi‐alicyclic polyimides (PIs) with designed flexible linkages have been synthesized derived from an alicyclic aromatic dianhydride (1,2,3,4‐cyclobutanetetracarboxylic dianhydride, CBDA) and various aromatic ether‐bridged diamines. The semi‐alicyclic PIs were evaluated as the photo‐alignment layers of liquid crystal (LC) molecules in liquid crystal display (LCD). Experimental results indicate that the photo‐alignment characteristics of LC molecules induced by the photo‐aligned PI layers and the electro‐optical (EO) properties of the LC cell devices are closely related with PI backbone structures. The retardation of the photo‐aligned PI layers is correlated with the ultraviolet (UV) absorption intensity of PI at 220 to approximately 330 nm. The higher UV absorption intensity PI has, the higher retardation and lower pre‐tilt angle the photo‐aligned PI layer exhibits. The defect‐free and photo‐aligned PI layer could result into the uniform LC texture, which is highly desired for in‐plane switching (IPS) mode LCD devices. In comparison, PI layer containing trifluoromethyl moiety shows poor photo‐aligning performance because of the strong electronic withdrawing effect of the fluorinated linkage.     

2,4-二硫代尿嘧啶的紫外吸收光谱和共振拉曼光谱

硫代嘧啶碱基是光动力疗法潜在的重要光敏剂,其最低单重激发态的光物理研究已有广泛报道。然而,其较高激发态的跃迁性质和反应动力学研究较为稀少。因此,本文采用共振拉曼光谱和密度泛函理论计算方法研究2,4-二硫代尿嘧啶的紫外光谱和几个较高单重激发态的短时结构动力学。首先,基于共振拉曼光谱强度与电子吸收带振子强度f的关系,将紫外光谱去卷积成四个吸收带,分别为358 nm(f=0.0336)中等强度吸收带(A带),338 nm(f=0.1491)、301 nm(f=0.1795)和278 nm(f=0.3532)强而宽的吸收带(B、C和D带)。这一结果既吻合密度泛函理论计算结果,又符合共振拉曼光谱强度模式对紫外光谱带的预期。据此,去卷积得到的四个吸收带被分别指认为S0→S2跃迁、S0→S6跃迁、S0→S7跃迁和S_0→S_8跃迁。同时,分别对B,C和D带共振拉曼光谱进行了详细的指认,获得了短时动力学信息。结果表明,S_8态短时动力学的显著特征是在Franck-Condon区域或附近发生了S8(ππ~*)/S(nπ~*)势能面交叉引发的、伴随超快结构扭转的非绝热过程。S7和S6态短时动力学的主要特征是反应坐标的多维性,它们分别沿C_5C_6/C_2S_8/C_4S_(10)/N_2C_3+C_4N_3H_9/N_1C_2N_3/C_2N_1C_6/C_6N_1H_7/C_5C_6H_(12)和C_5C_6/N_3C_2/C_4S_(10)/C_2S_8+C_6N_1H_7/C_5C_6H_(12)/C_5C_6N_1/C_5C_6H_(12)/C_2N_1C_6/N_1C_2N_3/C_4N_3H_9/N_1C_2N_3等内坐标演化。     

一种聚醚型芳香偶氮高分子染料

芳香偶氮聚合物是一类新型的高分子染料。本工作从对-N,N-二甲基苯胺出发,经重氮化和偶联反应,再与环氧氯丙烷缩合制备单体,最后用阳离子聚合方法得到了聚醚型芳香偶氮高分子染料——聚(对-N,N-二甲氨基偶氮苯基)缩水甘油醚。用元素分析,红外光谱和¹³C核磁共振确定了聚合物的结构,并测定了它的熔点,分子量等物理化学常数。 上述染料高分子与偏氯乙烯-丙烯酸甲酯共聚物组成光敏材料,测定了它的紫外感光特性。结果表明,高分子染料具有光敏成象性能,并能稳定地结合在光敏层内。     

A coloured ferroelectric side chain polymer

Coloured ferroelectric liquid-crystalline side chain copolymers containing 5 per cent and 15 per cent of an azo dye were synthesized and characterized by DSC, GPC and optical microscopy. Order parameters, S, of the azo compound exceeding 0·8 were measured in the frozen smectic phase for the 5 per cent copolymer. The copolymers exhibit fast electrooptic switching in the range of a few hundred microseconds to milliseconds in the S_c* phase. Both linear (i.e. electroclinic-like) and ferroelectric switching have been observed. Tilt angles of ∼19° and spontaneous polarization of ∼300nC cm^-2 have been recorded in the S_c* phase.     

Photo-dimerization of a chalcone-based side chain polymer for the alignment of ferroelectric liquid crystals

The alignment and optical properties of ferroelectric liquid crystal cells, having alignment films of a chalcone-based side chain polymer treated by linearly polarized UV irradiation were investigated. The long absorption band of the UV/Vis spectra gradually decreased and the FTIR spectra shifted as the irradiation times increased, indicating that cyclo-addition and isomerization reactions of the chalcone-based side chains occurred. UV dichroism demonstrated anisotropic changes in the alignment films, with a maximum at low exposure energy (0.5 J cm^-2). Liquid crystal molecules were aligned perpendicular to the polarization direction of the linearly polarized UV radiation. The azimuthal anchoring energy of liquid crystal E7 on a chalcone-based side chain polymer surface increased with exposure energy. Well aligned defect-free cells and high contrast ratio were achieved with irradiation of longer than 5 min; the geometric conditions for a stable C2 structure may be satisfied at low temperature with slowly cooling.     

Dynamic behaviour at a nematic liquid crystal-rubbednylon interface using evanescent wave photon correlation spectroscopy

Photon correlation spectroscopy of light scattered by director fluctuations from an evanescent optical wave propagating in the nematic liquid crystal 5CB is used to study the interfacial dynamic behaviour of the liquid crystal. The intensity correlation function of light scattered by interfacial orientation fluctuations is measured by illuminating to give a short optical penetration depth within the nematic. These surface scattering correlation functions strongly differ from the bulk correlation function and are interpreted in terms of a nematic surface orientation mode arising from the coupling between the director field and the fluid velocity. It is shown that the analysis of the surface mode gives a method for measuring anchoring energies in liquid crystals. The anchoring energy obtained for rotation of the director away from the rubbing direction about an axis normal to the surface for 5CB at a rubbed nylon surface is 7.14±0.7 × 10-² ergcm-².     

Synthesis and liquid crystal alignment properties of new cinnamate-based photocrosslinkable polymers

Because optical buffing can achieve aligning patterns with different azimuthal angles of the liquid crystal directors, photoalignment appears to be a very hopeful technique for designing complex LCD structures. Until recently, most photopolymers provided low anchoring and/or low tilt angles which are unsuitable for industrial applications. In this work, four new photocrosslinkable polymers based on biphenyl and naphthalene moieties have been prepared and characterized. These photopolymers have been irradiated with linearly polarized UV light, and liquid crystal cells have been made. The tilt angles generated by oblique irradiation have been measured as well as the anchoring energies. Finally, the stability of the liquid crystal alignment properties have been studied.     

Synthesis and liquid crystal alignment properties of new cinnamate-based photocrosslinkable polymers

Because optical buffing can achieve aligning patterns with different azimuthal angles of the liquid crystal directors, photoalignment appears to be a very hopeful technique for designing complex LCD structures. Until recently, most photopolymers provided low anchoring and/or low tilt angles which are unsuitable for industrial applications. In this work, four new photocrosslinkable polymers based on biphenyl and naphthalene moieties have been prepared and characterized. These photopolymers have been irradiated with linearly polarized UV light, and liquid crystal cells have been made. The tilt angles generated by oblique irradiation have been measured as well as the anchoring energies. Finally, the stability of the liquid crystal alignment properties have been studied.     

A spectral approach to determine location and orientation of azo dyes within surfactant aggregates

The UV–vis absorption properties of azo dyes are known to exhibit a variation with the polarity and acidity of the dye environment. The spectral properties of a series of anionic azo dyes were characterized to further probe the interaction of these dyes with two types of surfactant aggregates: (1) the spherical micelles formed in aqueous solution by alkyltrimethylammonium bromide (C_nTAB) surfactants with n = 10–16 and (2) the unilamellar vesicles spontaneously formed in water from binary mixtures of the oppositely-charged double-tailed surfactants cationic didodecyldimethylammonium bromide (DDAB) and anionic sodium dioctylsulfosuccinate (Aerosol OT or AOT). The observed dye spectra reflect the solvatochromic behavior of the dyes and suggest the location and orientation of the dye within the surfactant aggregates. Deconvolution of the overall spectra into sums of Gaussian curves more readily displays any contributions of tautomeric forms of the azo dyes resulting from intramolecular hydrogen bonding. The rich variation in UV/vis absorption properties of these anionic azo dyes supports their use as sensitive tools to explore the nanostructures of surfactant aggregates.     

Morphological and structural characteristics of diazo dyes at the air-water interface: in situ Brewster angle microscopy and polarized UV/vis analysis

A morphological analysis is presented for Langmuir films of the diazo dyes Sudan 4 (S4), Sudan 3 (S3), and Sudan red (SR), using Brewster angle microscopy. Stable nonmonomolecular structures are formed at the air-water interface denoted as a plateau in the pressure-area isotherms. Monolayer domains are evident by the contrastless image even before the pressure onset, which grow in size until it reached a condensed monolayer. This behavior resembles that of Langmuir films from simple aromatic fatty acids. Films from all the azo dyes display similar features, according to the surface potential isotherms and in situ polarized UV/vis spectroscopy except for the larger area per molecule occupied by S4 and SR. This is attributed to the presence of CH(3) groups that cause steric hindrance modifying the organization of diazo dye molecules at the air-water interface. UV/vis polarized absorption spectroscopy showed preferential orientation of S4 and S3 on the water surface, while SR molecules lie isotropically. For these three diazo dyes, film absorption was negligible at very large areas per molecule, becoming nonzero only at a critical area coinciding with the onset of surface potential. The critical area is ascribed to the formation of a H-bonded network between water molecules and diazo dye headgroups.     

Tris-chelate complexes with chiral ligands: In search of diastereoisomeric selectivity with remote stereogenic centres

The chiral ligands, 4,4′-bis{(1S,2R,4S)-(−)-bornyloxy}-2,2′-bipyridine, (1S,2R,4S)-1, and 4,4′-bis{(1R,2S,4R)-(+)-bornyloxy}-2,2′-bipyridine, (1R,2S,4R)-1, have been prepared and characterized by spectroscopic techniques and, for (1S,2R,4S)-1, by single crystal X-ray diffraction. Despite the use of enantiomerically pure ligands, the formation of the complexes [Fe((1S,2R,4S)-1)₃]²⁺, [Ru((1S,2R,4S)-1)₃]²⁺, [Ru((1S,2R,4S)-1)(bpy)₂]²⁺ and [Ru((1R,2S,4R)-1)(bpy)₂]²⁺ proceeds without preference for either the Δ or Λ-diastereoisomers.