Development of an enantioselective membrane from cellulose acetate propionate/cellulose acetate,for the separation of trans-stilbene oxide

This paper reports the characterization of new synthesized chiral polymeric membranes, based on a cellulose acetate propionate polymer. The flux and permselective properties of the membrane were studied using 50 % ethanol solution of (R,S)-trans-stilbene oxide as feed solution. Scanning electron microscopy revealed the asymmetric structure of these membranes. The roughness of the surface was measured by atomic force microscopy. The resolution of over 97 % enantiomeric excess was achieved when the enantioselective membrane was prepared with 18 wt% cellulose acetate and 8 wt% cellulose acetate propionate in the casting solution of dimethyl formamide/N-methyl-2-pyrrolidone/acetone, at 20 °C and 55 % humidity, and a water bath at 10 °C for the gelation of the membrane. The operating pressure and the feed concentration of the trans-stilbene oxide were 275.57, 345.19, and 413.84 kPa and 2.6 mM, respectively.     

Chiral separation of (R,S)-2-phenyl-1-propanol through cellulose acetate butyrate membranes

As the cellulose acetate butyrate possessed multichiral carbon atoms in its molecular structure unit, enantioselective membrane was prepared using cellulose acetate butyrate as membrane material. The flux and permselective properties of membrane using aqueous solutions of (R,S)-2-phenyl-1-propanol as feed solution was studied. The top surface and cross-section morphology of the resulting membranes were examined by scanning electron microscopy. When the membrane was prepared with 15 wt.% cellulose acetate butyrate and 20 wt.% DMF in the casting solution, and the operating pressure and feed concentration of racemate were 2 kgf/cm² and 5 mmol/L, respectively, over 98% of enantiomeric excess (e.e.) was obtained. This is a report, for the first time, that the cellulose acetate butyrate is used as optical resolution membrane material for isolating the optical isomers of (R,S)-2-phenyl-1-propanol.     

Is the electrocatalytic epoxidation of stilbene isomers using manganese (III) tetradentate Schiff bases complexes stereoselective?

Three manganese (III) complexes were obtained with H₂Salen derivatives and used as catalysts in the epoxidation reactions of E- and Z-stilbene isomers. The preparative electrolyses were carried out at 25 °C in acetonitrile solution containing 0.1 M TBAP, 10⁻³ M complex, 10⁻² M 2-methylimidazole and 0.1 M benzoic anhydride plus stilbene as substrate. Our results showed clearly that E-stilbene was totally converted to Z-stilbene oxide whereas Z-stilbene leads to a mixture in which the benzaldehyde was the major by-product. In our experimental conditions, the turnovers recorded for different experiments were located in the 3.7–6.6 range.     

4-trans-Amino-proline based di- and tetrapeptides as organic catalysts for asymmetric C–C bond formation reactions

4-trans-Amino-proline based di- and tetrapeptides have been successfully applied as chiral organocatalysts in the enantioselective conjugate addition of nitroalkanes to cyclic enones and the direct aldol reaction. Two 4-trans-amino-proline residues were shown to be sufficient enough to catalyze the conjugate addition reactions with up to 88% ee and up to 100% yield. It has been demonstrated that 4-trans-amino-proline based di- and tetrapeptides are significantly more active than l-proline (at 30 mol %) and can catalyze the direct aldol reaction with good yield and enantioselectivity within 3 h and at lower catalyst loading (5 mol %).     

Separation performance of polyimide composite membrane prepared by dip coating process

The effects of the preparation conditions in a dip coating process on polyimide composite membranes have been investigated. Polyimide precursor obtained from pyromellitic dianhidride (PMDA) and 4,4′-oxydianiline (ODA) was mixed with triethylamine and poly(amic acid)tri-ethylamine salt (PAA salt) was made. An asymmetric polyimide membrane (PI-2080) as a supporting membrane was dipped in a PAA salt (concentration 0–5 wt.%) methanol solution. The coating layers of PAA salt were converted to these of polyimide by annealing at 200°C for 3 h in an ordinary vacuum oven.The performance of the polyimide composite membrane was evaluated by gas permeation (N₂, O₂, CO₂, at 1 kg/cm²) and pervaporation (feed: a 95 vol.% ethanol aqueous solution at 30–60°C). The composite membranes prepared using a coating solution of 5 wt.% PAA salt showed the CO₂/N₂ selectivity of over 25 on gas permeation, and separation factor α (H₂O/EtOH) of over 800 with a total flux of 0.21 kg/m² h on pervaporation.     

Novel chiral copper complexes of N,P-ferrocenyl ligands with central and planar chirality as efficient catalyst for asymmetric addition of diethylzinc to imines

A new type of chiral copper complexes of N,P-ferrocenyl ligands with central and planar chirality as efficient catalyst was applied to the enantioselective addition of diethylzinc to N-diphenylphosphinoylimines. The (R)- and (S)-enantiomers of the addition reaction were obtained for this transformation. In the presence of 6 mol % of bidentate ligand 1 and 12 mol % of Cu(OTf)₂, the asymmetric addition process affords N-diphenylphosphinoylamides in up to 97% ee and 95% yields.     

Separation of linear hydrocarbons and carboxylic acids from ethanol and hexane solutions by reverse osmosis

In this study, asymmetric cellulose acetate membranes with moderate NaCl rejection (85.5%) were prepared and used to study the influence of the chemical nature of organic solutes in different organic solvents. The solute rejection and the solvent flux of linear hydrocarbons (M_w=226–563 g/mol) and linear carboxylic acids (M_w=228–340 g/mol) in ethanol and hexane were studied as a function of the molecular weight, the feed concentration and the transmembrane pressure.The ethanol flux was three times higher than the hexane flux. The rejection coefficients for both types of solute were quire acceptable (R=60–90%), when ethanol was the solvent. In hexane the linear hydrocarbons showed a rejection of 40–60%, while all carboxylic acids reached a negative rejection of −40 to −20%. This negative “observed” rejection can be attributed to accumulation of carboxylic acid at the membrane; the solute concentration at the membrane becomes much higher than in the bulk solution, due to a higher affinity of the solute with the membrane in hexane than in ethanol. Sorption experiments support this hypothesis.Furthermore, it was found that the rejection increases with increasing molecular weight and the rejection and flux are hardly affected by the feed concentration.     

Enantioselective rhodium-catalyzed hydroacylation to access the four stereoisomers of anti-rodent difenacoum

An efficient asymmetric synthesis of the four stereoisomers of difenacoum, an anticoagulant currently used as a rodenticide in racemic form, is performed using a key step of rhodium catalyzed enantioselective intramolecular hydroacylation. Optimization of the last step, condensation of 4-hydroxycoumarin with chiral 3-([1,1′-biphenyl]-4-yl)-1,2,3,4-tetrahydronaphthalen-1-ol, is also discussed. After chromatographic separation of the cis and trans diastereoisomers, the four stereoisomers were all obtained with excellent enantioselective and diastereoselective excess (ee ≈ 96% and de >96%).     

Asymmetric nitroaldol reaction catalyzed by a chromium(III)–salen system

Chiral chromium(III)–salen-type complexes derived from 1,2-diaminocyclohexane and 1,2-diphenylethylenediamine were found to catalyze the enantioselective Henry reaction. Various arylaldehydes, trans-cinnamaldehyde, and cyclohexanecarbaldehyde reacted with nitromethane in the presence of (i-Pr)₂NEt and salen–CrCl (2 mol %) to give the corresponding adducts in 40–76% ee and in moderate to good yields.     

Enantioselective hydrolysis of styrene oxide with the epoxide hydrolase of Sphingomonas sp. HXN-200

The soluble bacterial epoxide hydrolase (EH) from Sphingomonas sp. HXN-200 catalyzed the enantioselective hydrolysis of racemic styrene oxide to give (S)-styrene oxide with an enantiomeric ratio (E) of 21–23 in aqueous buffer, better than any reported native EHs. The ring opening of the styrene oxide with this EH was only at the terminal position for the (S)-enantiomer and at the terminal and benzylic position in an 87:13 ratio for the (R)-enantiomer. Enzymatic hydrolysis of the styrene oxide in a two-liquid phase system significantly reduced autohydrolysis, thus improving the E to 26–29. Hydrolysis of 160 mM styrene oxide with cell-free extract (CFE) of Sphingomonas sp. HXN-200 (10 mg protein/mL) in aqueous buffer and n-hexane (1:1) for 30.7 h afforded 39.2% (62.7 mM) of (S)-styrene oxide in >99.9% ee. The lyophilized CFE was proven to be stable, while the rehydrated lyophilized CFE powder was successfully used for the hydrolysis of 320 mM styrene oxide in the two-liquid phase system, yielding 40.2% (128.6 mM) of (S)-styrene oxide in >99.9% ee after 13.8 h. No inhibitory effect of the diol product on the hydrolysis was observed when the diol concentration was lower than 476 mM, suggesting a straightforward process for the hydrolysis of up to 1 M styrene oxide.     

Thermodynamic properties of CO2 absorption in hydroxyl ammonium ionic liquids at pressures of (100–1600) kPa

Solubility of CO₂ in six hydroxyl ammonium ionic liquids 2-hydroxyethanaminium acetate [hea], bis(2-hydroxyethyl)ammonium acetate [bheaa], 2-hydroxy-N-(2-hydroxyethyl)-N-methylethanaminium acetate [hhemea], 2-hydroxyethanaminium lactate [hel], bis(2-hydroxyethyl)ammonium lactate [bheal], 2-hydroxy-N-(2-hydroxyethyl)-N-methylethanaminium lactate [hhemel] at temperatures (298.15, 313.15, and 328.16) K and pressures ranging from (100 to 1600) kPa was determined. From the experimental solubility data, the Henry’s constant of CO₂ for each hydroxyl ammonium ionic liquids was estimated and reported as a function of temperature. Furthermore, enthalpy and entropy of absorption were obtained from estimated Henry’s constant. The results showed that the solubility increase with increasing pressure and decrease with increasing temperature and the solubility of CO₂ in these six hydroxyl ammonium ionic liquids was in sequence: [hea] > [bheaa] > [hel] > [bheal] > [hhemel] > [hhemea].     

The wet phase separation: the effect of cast solution thickness on the appearance of macrovoids in the membrane forming ternary cellulose acetate/acetone/water system

We report on novel observations on the appearance of macrovoids in the ternary cellulose acetate (CA)/acetone (ACE)/water membrane forming system. The membranes are prepared by the wet phase separation whereby the cast solution is composed of ACE and polymer, and the coagulation bath is pure water only. It is found that the macrovoid formation in a 12.5 wt.% cast solution strongly depends on the cast solution thickness: macrovoids appear at the thickness of 500 μm but not at 150 and 300 μm.     

Chemical modification of cellulose extracted from sugarcane bagasse: Preparation of hydroxyethyl cellulose

Cellulose was extracted from sugarcane bagasse by alkaline extraction with sodium hydroxide followed by delignification/bleaching using sodium chlorite/hexamethylenetetramine system. Factors affecting extraction process, including sodium hydroxide concentration, hexamethylenetetramine concentration and temperature were studied and optimum conditions for alkaline extraction were found to be boiling finely ground bagasse under reflux in 1 N sodium hydroxide solution and then carrying out the delignification/bleaching treatment at 95 °C using 5 g/l sodium chlorite together with 0.02 g/l hexamethylenetetramine. The extracted cellulose was used in the preparation of hydroxyethyl cellulose through reaction with ethylene oxide in alkaline medium. Factors affecting the hydroxyethylation reaction, like sodium hydroxide concentration during the alkali formation step, ethylene oxide concentration, reaction temperature and reaction duration were studied. Optimum conditions for hydroxyethylation reaction were using 20% NaOH solution and 200% ethylene oxide (based on weight of cellulose), carrying out the reaction at 100 °C for 60 min.     

Enantioselective transesterification of (RS)-1-chloro-3-(3,4-difluorophenoxy)-2-propanol using Pseudomonas aeruginosa lipases

Lipases from the bacterial strain, Pseudomonas aeruginosa, isolated from the soil by enrichment techniques, are assessed for the enantioselective transesterification of (RS)-1-chloro-3-(3,4-difluorophenoxy)-2-propanol (rac-CDPP) to (R)-1-chloro-3-(3,4-difluorophenoxy)-2-propanol, a key intermediate in the synthesis of the chiral drug (S)-Lubeluzole. The lipases produced by the organism yielded the (S)-ester and the (R)-alcohol as the remaining substrate with an excellent yield (>49.9%) and almost complete enantioselectivity (ee >99.9%) in the presence of vinyl butyrate as an acyl donor in an organic medium. In contrast, purified and expensive commercially available lipases of Candida rugosa and porcine pancreas achieved much lower conversion with enantioselectivities of 15% and 5%, respectively. A well-mixed (∼1000 rev min⁻¹) batch reactor having the aqueous phase finally dispersed in hexane was used in these studies. The parameters of the transesterification reaction were optimized and the optimal concentrations of rac-CDPP and vinyl butyrate were found to be 5 and 150 mM at 30 °C. A preparative-scale reaction yielded the (S)-ester at 42% conversion and ee >99%.     

Effect of separating layer in pervaporation composite membrane for MTBE/MeOH separation

The composite membranes with polyvinylalcohol (PVA) as separating layer material and polyacrylonitrile (PAN) or cellulose acetate (CA) as supporting layer material were prepared for separating methyl tert-butyl ether (MTBE)/MeOH mixture by pervaporation (PV). The results showed that PV performance of the composite membrane with PVA membrane as separating layer was superior to that with CA membrane as separating layer, and the PV performance of PVA/CA composite membrane with CA membrane as supporting layer was better. The parameters to prepare the composite membrane remarkably affected PV performance of the composite membrane. The permeate flux of both composite membranes of PVA/PAN and PVA/CA was over 400 g/m² h, and the concentration of MeOH in the permeate reached over 99.9 wt.% for separating MTBE/MeOH mixture.     

Benign synthesis of N-(8-quinolyl)pyridine-2-carboxamide) ligand (Hbpq), and its Ni (II) and Cu (II) complexes. A fluorescent probe for direct detection of nitric oxide in acetonitrile solution based on Hbpq copper(II) acetate interaction

The ligand Hbpq = N-(8-quinolyl)pyridine-2-carboxamide) has been prepared using tetrabutylammonium bromide (TBAB) as an environmentally friendly reaction medium. Four new complexes of this ligand, [M(bpq)X] (M = Cu(II), X = SCN̄ (1), N₃̄ (2); M = Ni(II), X = SCN̄ (3), N₃̄ (4)), have also been synthesized and fully characterized. The crystal and molecular structures of [Cu(bpq)(NCS)]_n (1) have been determined by X-ray crystallography. Copper(II) ion adopts a distorted square pyramidal (4 + 1) coordination in this complex. Hbpq ligand shows a strong emission at 500 nm in acetonitrile solution. The emission is quenched in the presence of copper(II) acetate, apparently because of the formation of [Cu(L)(OAc)(H₂O)] complex. Introduction of nitric oxide (NO) into the acetonitrile solution at room temperature induces an increase in the fluorescence intensity, presumably due to the reduction of Cu(II) to Cu(I). This process is reversible and can form a basis for direct detection of NO.     

Transformation of racemic ethyl 3-hydroxybutanoate into the (R)-enantiomer exploiting lipase catalysis and inversion of configuration

Racemic ethyl 3-hydroxybutanoate rac-1 was transformed into ethyl (R)-acetoxybutanoate (ee = 92%) with 85–90% chemical yields using enantioselective acylation with isopropenyl acetate in the presence of Candida antarctica lipase B (CAL-B, Novozym 435) under solvent-free conditions, followed by mesylation of the unreacted (S)-alcohol in the reaction mixture and inversion of configuration with cesium acetate in DMF in one pot. When the (R)-acetoxybutanoate was subjected to alcoholysis with ethanol and CAL-B, enantiopure (R)-1 (ee >99%) was produced.     

Liquid–liquid equilibrium in ternary systems N,N-dimethylformamide + 2-methylpentane + methanol and N,N-dimethylformamide + methylcyclohexane + methanol

In the present paper, a study of temperature behaviour of the liquid–liquid equilibrium in ternary systems N,N-dimethylformamide + 2-methylpentane + methanol and N,N-dimethylformamide + methylcyclohexane + methanol. The analysis of critical curves of the liquid–liquid equilibrium by means of the regular solution model was carried out. The acquired predictions were subsequently verified experimentally.     

Asymmetric conjugate addition of thioglycolate to a range of chalcones using tetrahydroisoquinoline (TIQ) N,N′-dioxide ligands

A series of novel TIQ based N,N′-oxide ligands were synthesised and screened for their catalytic activity in the enantioselective conjugate addition of thioglycolate to chalcones. Bulky groups on the side chain of the TIQ backbone provided the highest enantioselectivity of up to 88% with 10 mol % catalyst loading. It was also observed that these reactions proceeded optimally in the presence of dichloromethane as a solvent. Screening of various metals emphasized La(OTf)₃ as the ideal pre-catalyst for this particular reaction.     

Argon and nitrogen beams influencing membrane permeate fluxes and microbial growth

Porous cellulose and dense chitosan membranes were bombarded with argon and nitrogen-ion beams using two energy levels, 30 and 120 keV, of the same fluency of 5×10¹⁴ ions/cm² for a comparison study. The results revealed that both beam types reduced the hydraulic permeability of the membranes. Using a NaCl solution of 4000 ppm concentration as feed, the ability to reject salt of dense chitosan membrane was reduced only if it was pretreated with 120 keV nitrogen-ion beams. A Fourier Transform Infrared Spectroscopy study showed that molecular weight of chitosan was possibly decreased after the bombardment with 120 keV beams. The analysis of the cellulose membranes revealed that a dense structure was created without affecting the OH functional groups. This study found that only chitosan membranes possessed an anti-fungi property if being implanted with positive charges of nitrogen or argon ions of 120 keV.