A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Nanocomposite of manganese ferrocyanide and graphene: A promising cathode material for rechargeable lithium ion batteries

A nanocomposite of potassium manganese ferrocyanide and graphene (12% C, 88% K_1.8Mn_1.1Fe(CN)₆∙ 0.27H₂O) was prepared by ball milling of graphene oxide powder and nanoparticles of manganese–iron Prussian Blue. It exhibits enhanced electrochemical performance compared to pure Prussian Blue with a specific capacity of 150 mAhg^− 1 at average 3.8 V vs. Li⁺/Li and a good cyclability. The nanocomposite can be considered as competitive to standard cathode materials of present rechargeable lithium ion batteries like cobalt oxide, iron phosphate or NMC.     

Preparation of a poly(methyl methacrylate)-reduced graphene oxide composite with enhanced properties by a solution blending method

Poly(methyl methacrylate) (PMMA)/graphene nanocomposites were prepared by a simple solution blending method. The glass transition temperature of the produced PMMA/graphene composite was increased by 37 °C with 1.0 wt.% RGO content, which is approximately 40% of improvement compared to that of pure PMMA. The thermal expansion coefficient (TEC) decreased by 68% with as low as 0.1 wt.% RGO loading. The electrical conductivity of the nanocomposites reached up to 0.037 S/m even with only 2.0 wt.% RGO, which increased by more than twelve orders of magnitude. The resulting nanocomposites showed that a stable colloidal suspension of graphene dispersion in organic solvent before blending with PMMA is necessary to fabricate the nanocomposites with enhanced properties.     

Facile one-pot synthesis of fluorinated graphene oxide for electrochemical sensing of heavy metal ions

Doping and functionalization could significantly assist in the improvement of the electrochemical properties of graphene derivatives. Herein, we report a one-pot synthesis of fluorinated graphene oxide (FGO) from graphite. The surface morphology, functionalities and composition of the resulting FGO have been studied using various surface characterization techniques, revealing that layer-structured nanosheets with ~ 1.0 at.% F were formed. The carbon bound F exhibited semi-ionic bonding characteristic and significantly increased the capacitance of FGO compared to GO. Further, the FGO has been employed for the simultaneous detection of heavy metal ions Cd^2 +, Pb^2 +, Cu^2 + and Hg^2 + using square wave anodic stripping voltammetry; and a substantial improvement in the electrochemical sensing performance is achieved in comparison with GO.     

Novel core–shell SDC/amorphous Na2CO3 nanocomposite electrolyte for low-temperature SOFCs

Novel core–shell SDC (Ce_0.8Sm_0.2O_1.9)/amorphous Na₂CO₃ nanocomposite was prepared for the first time. The core–shell nanocomposite particles are smaller than 100 nm with amorphous Na₂CO₃ shell of 4–6 nm in thickness. The nanocomposite electrolyte shows superionic conductivity above 300 °C, where the conductivity reaches over 0.1 S cm⁻¹. Such high conductive nanocomposite has been applied in low-temperature solid oxide fuel cells (LTSOFCs) with an excellent performance of 0.8 W cm⁻² at 550 °C. A new potential approach of designing and developing superionic conductors for LTSOFCs was presented to develop interface as ‘superionic highway’ in two-phase materials based on coated SDC.     

Multilayer graphene nanoribbons exhibit larger capacitance than their few-layer and single-layer graphene counterparts

This article demonstrates that it is not always beneficial to exfoliate graphitic structures to single-layer graphene to achieve maximum electrochemical performance. Using electrochemical impedance spectroscopy, we show that multilayer graphene nanoribbons with cross sections of 100 × 100 nm provide larger capacitance (15.6 F/g) than do few-layer graphene nanoribbons (14.9 F/g) and far larger capacitance than single-layer graphene nanoribbons (10.9 F/g) with the same cross section.     

Chemical bath deposition of CdS quantum dots on vertically aligned ZnO nanorods for quantum dots-sensitized solar cells

Formation of CdS quantum dots (Q dots) on the vertically aligned ZnO nanorods electrode was carried out by chemical bath deposition. The diameter and thickness of ZnO nanorods are ～100–150 nm and ～1.6 μm, respectively, and CdS Q dots on ZnO nanorods have a diameter of smaller than 15 nm. In application of the Q dots-sensitized solar cells, composite film exhibited a power conversion efficiency of 0.54% under air mass 1.5 condition (80 mW/cm²), and incident-photon-to-current conversion efficiency showed 18.6%.     

Short aspect ratio gold nanorods prepared using gamma radiation in the presence of cetyltrimethyl ammonium bromide (CTAB) as a directing agent

The synthesis of short aspect ratio gold nanorods using gamma radiation method by incorporating cetyltrimethyl ammonium bromide (CTAB) as a directing agent is reported in this communication. The radiolysis of Au⁺, in the presence of 2.5 nm Au seeds and 0.1 mol dm^?3 isopropanol, results in the formation of Au spheres as evident from surface plasmon resonance band at 527 nm. However, by carrying out radiolysis at lower radiation dose rate, short aspect gold nanorods having surface plasmon bands at 513 and 670 nm have been prepared. The formation of rods at low radiation dose rate was observed to be governed by the kinetics of particle growth. The TEM of as-synthesized nanoparticles confirmed the formation of uniform sized nanorods having an aspect of 2.4.     

Flexible free-standing graphene-silicon composite film for lithium-ion batteries

Flexible, free-standing, paper-like, graphene-silicon composite materials have been synthesized by a simple, one-step, in-situ filtration method. The Si nanoparticles are highly encapsulated in a graphene nanosheet matrix. The electrochemical results show that graphene-Si composite film has much higher discharge capacity beyond 100 cycles (708 mAh g^? 1) than that of the cell with pure graphene (304 mAh g^? 1). The graphene functions as a flexible mechanical support for strain release, offering an efficient electrically conducting channel, while the nanosized silicon provides the high capacity.     

Nanorods of transition metal oxalates: A versatile route to the oxide nanoparticles

A versatile route has been explored for the synthesis of nanorods of transition metal (Cu, Ni, Mn, Zn, Co and Fe) oxalates using reverse micelles. Transmission electron microscopy shows that the as-prepared nanorods of nickel and copper oxalates have diameter of 250 nm and 130 nm while the length is of the order of 2.5 μm and 480 nm, respectively. The aspect ratio of the nanorods of copper oxalate could be modified by changing the solvent. The average dimensions of manganese, zinc and cobalt oxalate nanorods were 100 μm, 120 μm and 300 nm, respectively, in diameter and 2.5 μm, 600 nm and 6.5 μm, respectively, in length. The aspect ratio of the cobalt oxalate nanorods could be modified by controlling the temperature.The nanorods of metal (Cu, Ni, Mn, Zn, Co and Fe) oxalates were found to be suitable precursors to obtain a variety of transition metal oxide nanoparticles. Our studies show that the grain size of CuO nanoparticles is highly dependent on the nature of non-polar solvent used to initially synthesize the oxalate rods. All the commonly known manganese oxides could be obtained as pure phases from the single manganese oxalate precursor by decomposing in different atmospheres (air, vacuum or nitrogen). The ZnO nanoparticles obtained from zinc oxalate rods are ～55 nm in diameter. Oxides with different morphology, Fe₃O₄ nanoparticles faceted (cuboidal) and Fe₂O₃ nanoparticles (spherical) could be obtained.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

Electrochemical synthesis of Au/polyaniline–poly(4-styrenesulfonate) hybrid nanoarray for sensitive biosensor design

Au/polyaniline (PANI)–poly(4-styrenesulfonate) (PSS) hybrid nanoarray is fabricated for biomolecular sensing in neutral aqueous solutions. Firstly, an array of one-dimensional Au nanorods (diameter = ca. 200 nm, length = ca. 3 μm) is formed by a template-electrodeposition method using a porous anodic alumina membrane, and then a thin PANI–PSS composite layer is electropolymerized on the surface of the Au nanorods. The resulting Au/PANI–PSS hybrid nanoarray exhibits a quasi-reversible redox electrochemical process at ca. +0.11 V and electrocatalytic oxidation of reduced β-nicotinamide adenine dinucleotide (NADH) is attained with a detection limit of 0.3 μM in a neutral solution.     

Electrografting of amino-TEMPO on graphene oxide and electrochemically reduced graphene oxide for electrocatalytic applications

4-Amino-2,2,6,6-tetramethyl-1-piperridine N-oxyl (4-amino-TEMPO), an electroactive nitroxide radical, was attached to the surface of graphene oxide (GO) and electrochemically reduced graphene oxide (ERGO) modified glassy carbon electrode by a simple, rapid and green electrografting method. The electroactive interfaces were analyzed by X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). The calculated surface coverage for 4-amino-TEMPO is up to 1.55 × 10^− 9 mol·cm^− 2. The modified electroactive interface exhibited excellent electrocatalytic activity towards the electro-oxidation of reduced glutathione (GSH) and hydrogen peroxide (H₂O₂).     

Graphene and carbon quantum dots electrochemistry

Graphene and carbon quantum (QDs) dots exhibit interesting and well-defined properties owing to their quantum confinement. In this work, graphene QDs (G-QDs) and carbon QDs of size ~ 6 nm and ~ 2 nm, respectively, were prepared and their potential uses in electrochemistry and electrochemical sensing were subsequently investigated. It was discovered that the C-QDs surface displayed a faster electron transfer rate compared to the G-QDs following analyses with the ferro/ferricyanide redox probe. Studies were also carried out with redox biomarkers such as uric acid (UA) and ascorbic acid (AA), and it was found that while the C-QDs displayed electrocatalytic properties toward the oxidation of both UA and AA, the G-QDs seemed to only have an impact on AA, from the decrease in the oxidation peak potential. This work provides direct electrochemical comparison of the two latest frontiers of carbon nanomaterials and opens the way for their electrochemical sensing applications.     

Optical and electrical conducting properties of Polyaniline/Tin oxide nanocomposite

Polyaniline(PANI)/Tin oxide (SnO₂) hybrid nanocomposite with a diameter 20–30 nm was prepared by co-precipitation process of SnO₂ through in situ chemical polymerization of aniline using ammonium persulphate as an oxidizing agent. The resulting nanocomposite material was characterized by different techniques, such as X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infrared spectroscopy (FT-IR) and Ultraviolet–Visible spectroscopy (UV–Vis), which offered the information about the chemical structure of polymer, whereas electron microscopy images provided information regarding the morphology of the nanocomposite materials and the distribution of the metal particles in the nanocomposite material. SEM observation showed that the prepared SnO₂ nanoparticles were uniformly dispersed and highly stabilized throughout the macromolecular chain that formed a uniform metal-polymer nanocomposite material. UV–Vis absorption spectra of PANI/SnO₂ nanocomposites were studied to explore the optical behavior after doping of nanoparticles into PANI matrix. The incorporation of SnO₂ nanoparticles gives rise to the red shift of π–π¹ transition of polyaniline. Thermal stability of PANI and PANI/SnO₂ nanocomposite was investigated by thermogravimetric analysis (TGA). PANI/SnO₂ nanocomposite observed maximum conductivity (6.4 × 10^?3 scm^?1) was found 9 wt% loading of PANI in SnO₂.     

Characterization of thin InP anodic oxide layers: Correlation of morphological investigations with chemical and electrical properties

Depending on the applied electrochemical parameters, various oxide films can be grown onto InP in aqueous media. In this work, two oxide layers have been grown in borate buffer solution at pH = 9 by applying a low (0.2 mA cm⁻²) or a high (30 mA cm⁻²) current density, but a similar coulometric charge. Capacitance–voltage measurements performed before and after the anodic processes have been made to investigate the electrical properties of new interfaces, while X-ray photoelectron spectroscopy (XPS) analysis and atomic force microscopy (AFM) observations were used to access to the chemical and topographic aspects of the two oxidized surfaces. It is demonstrated that AFM observations coupled with electrochemical and XPS measurements is a good probe for the study of thin oxide on InP. A correlation between the anodization parameters and the resulting electrical and morphological aspects of the anodic layers is clearly evidenced.     

Li2ZnTi3O8 nanorods: A new anode material for lithium-ion battery

Spinel Li₂ZnTi₃O₈ nanorods were first synthesized using titanate nanowires as a precursor. The synthesized nanorods are highly crystalline and used as an anode material in a rechargeable Li-ion battery. A large capacity of 220 mA h g^? 1 was kept after 30 cycles at a current density of 0.1 A g^? 1, which is close to the theoretic capacity. The electrochemical measurements indicate that the anode material made of spinel Li₂ZnTi₃O₈ nanorods displayed a highly reversible capacity and excellent cycling stability.     

Electrodeposition of highly alloyed quaternary PtPdRuOs catalyst with highly ordered nanostructure

Introducing palladium to traditional platinum-based alloy electrocatalysts offers a novel approach to develop highly efficient anode electrocatalysts for direct methanol fuel cells. In this communication, we report the preparation of thin-wall mesoporous quaternary PtPdRuOs alloy catalyst via electrochemical co-reduction of their chloride precursors all dissolved in aqueous domains of the liquid crystalline phases of an oligoethylene oxide surfactant. Scanning electron micrographs (SEM) reveal that the deposit is composed of uniform nanospheres with an average diameter of around 120 nm and the average mole composition of the metal elements is Pt₃₇Pd₃₃Ru₂₂Os₁₀. Transmission electron micrographs (TEM) disclose that the nanospheres have an ordered nanostructure which is characterized by periodic pores of 3.6 ± 0.4 nm in diameter separated by walls of 2.4 ± 0.4 nm in thickness. X-ray diffraction studies signal a highly alloying degree for the four metal components in the deposit. The specific electrochemical surface area of the nanostructured powder assessed using underpotential deposited Cu stripping technique is as high as 105 m² g^–1, much higher than that of unsupported precious metal catalysts prepared using standard techniques. These characters suggest that the quaternary PtPdRuOs alloy materials with high surface area and thin-wall mesoporous structure would be a novel class of promising electrocatalysts for direct methanol fuel cells.     

Electrochemical and FTIR spectroscopic study of CO2 reduction at a nanostructured Cu/reduced graphene oxide thin film

Here we report a facile approach to synthesize a novel nanostructured thin film comprising Cu nanoparticles (NPs) and reduced graphene oxide (rGO) on a glassy carbon electrode (GCE) via the direct electrochemical reduction of a mixture of cupper and graphene oxide (GO) precursors. The effect of the applied potential on the electrochemical reduction of CO₂ was investigated using linear sweep voltammetric (LSV) and chronoamperometric (CA) techniques. Carbon monoxide and formate were found as the main products based on our GC and HPLC analysis. The electrochemical reduction of CO₂ at the Cu/rGO thin film was further studied using in situ ATR-FTIR spectroscopy to identify the liquid product formed at different applied cathodic potentials. Our experimental measurements have shown that the nanostructured Cu/rGO thin film exhibits an excellent stability and superb catalytic activity for the electrochemical reduction of CO₂ in an aqueous solution with a high current efficiency of 69.4% at − 0.6 V vs. RHE, promising for the efficient electrochemical conversion of CO₂ to valuable products.