A new type of a spectrometric microtitration set up

A spectrometric microtitrator was developed from a spectrometer with a microreaction chamber and a tri-colour light-emitting diode (LED) as the light source. A novel, vertical, optical geometry of the spectrometric microtitration chamber was introduced and tested. This novel geometry also required a new method for mixing the titrated solution. A laboratory-made 50 μl syringe pump was used for the addition of the titration reagent. The 10-channel module for light effects, which makes possible a low-cost hardware approach to changing the titration protocols, was used for coordinating the operation of the microtitration set up. The system, with 10 channels and a regulated speed of operation, is flexible enough to allow an operator to generate different titration protocols. The performance test showed that the speed of titration-reagent addition can be regulated in the range from 0.87 to 21.8 μl min⁻¹. The smallest achievable volume addition is equal to 35 nl. The mixing rate can be continuously regulated by an electrical pulse that initiates the mixing cycle. The quickest rate is every 1.6 s, and the slowest rate is every 4.8 s. The spectrometric microtitration set up was successfully tested for several different real-life spectrometric titrations, including an iodometric titration, a determination of CO₂ in deionised water, and EDTA titrations of copper(II) ions with no indicator. The volume of the examined solution can be as small as 220 μl. The titration-reagent consumption is usually between 10 and 35 μl. Coefficients of variation of the end point volume determination (n = 5) at different experimental conditions and different average volumes of consumed reagents (7.06, 12.17 and 22.88 μl) were 2.4, 1.3 and 1.2%, respectively. The novel geometry of the spectrometric microtitration chamber proved to be useful for real-life applications.     

Pulsed multi-wavelength excitation using fiber-in-capillary light emitting diode induced fluorescence detection in capillary electrophoresis

A novel instrument was developed using a multi-wavelength pulsed LED array with in-column optic-fiber induced fluorescence detection by capillary electrophoresis. The light from 2 different wavelength LEDs (450 nm and 480 nm) was pulsed for short intervals at high intensity. The beam from each LED was collimated and reshaped with the gradient index (GRIN) lens group to achieve a highly effective coupling between LED light source and an optical fiber. The optical fiber was placed inside the capillary for in-capillary LED-induced fluorescence detection. The advantages of this system were validated by the simultaneous determination of vitamin B2 and fluorescein. Detection limits for vitamin B2 and fluorescein were estimated to be 5 nM and 0.29 nM (S/N = 3), respectively. The relative standard deviations (RSDs, n = 6) of the both compounds for migration time and peak area were better than 0.83%, 2.20% and 1.21%, 2.75%, respectively. The method was applied to the determination of vitamin B2 in commercial tablets and fluorescein in fluorescein sodium injection and the recoveries obtained were in the range of 96.6-102.0% and 99.9-102.8%, respectively. It was also applied to human serum, where the recoveries were found to be in the range of 94.4-97.0% and 92.6-96.4%, respectively. The system has been successfully applied in separation and determination of the both biological samples with acceptable analytical performance.     

Speciation of chromium in natural waters by micropumping multicommutated light emitting diode photometry

A simple and sensitive multicommutated flow procedure, implemented by employing a homemade light emitting diode (LED) based photometer, has been developed for the determination of chromium (VI) and total chromium in water. The flow system comprised a set of four solenoid micro-pumps, which were assembled to work as fluid propelling and as commutating devices. The core of the detection unit comprised a green LED source, a photodiode and a homemade flow cell of 100 mm length and 2 mm inner diameter. The photometric procedure for the speciation of chromium in natural waters was based on the reaction of Cr (VI) with 1,5-diphenylcarbazide. Cr (III) was previously oxidized to Cr (VI) and determined as the difference between total Cr and Cr (VI). After carrying out the assays to select the best operational conditions the features of the method included: a linear response ranging from 10 to 200 μg l⁻¹ Cr (III) and Cr (VI) (r = 0.999, n = 7); limits of detection of 2.05 and 1.0 μg l⁻¹ for Cr (III) and Cr (VI), respectively; a relative standard deviation lower than 2.0% (n = 20) for a typical solution containing 50 μg l⁻¹ Cr; a sampling throughput of 67 and 105 determinations per hour for total Cr and Cr (VI), respectively, and recovery values within the range of 93-108% for spiked concentrations of the order of 50 μg l⁻¹.     

Micropumping multicommutation turbidimetric analysis of waters

A micropumping multicommutation manifold to perform turbidity determinations in waters is described. The procedure is based on the use of a combination of hydrazine sulfate and hexamethylenetetramine, to obtain an external standard of nephelometric turbidity units (NTU), which could compare the absorbance measurements at high wavelengths for samples with a calibration line obtained from a concentrated formazine standard diluted on-line. To minimize sample and reagent consumption and waste generation, the flow system was designed with two solenoid micro-pumps, one of them for the alternative introduction of the formazine standard and samples and the other one for the water carrier. The multicommutation approach makes possible the on-line dilution of a single standard to obtain the external calibration. The linear response was ranged up to 160 NTU. The coefficient of variation was estimated as 1.6 and 3.2% for 10 and 100 mm flow cell, respectively, for solutions containing 40 NTU (n = 10). Approximately, 60 determinations can be carried out per hour with limit of detection values of 1 and 0.1 NTU, consuming only 160 or 240 μL formazine solution and generating 1.8 or 2.0 mL waste per determination, using measurement cells of 10 and 100 mm optical pathlength, respectively. The procedure was successfully applied to 11 different water samples. Recovery studies were carried out and results obtained were between 97.5 ± 0.2 and 100 ± 1%. The development of a homebuilt light emitting diode (LED)-based portable flow analysis instrument was checked for in situ turbidimetric measurements, providing this equipment a LOD value of 0.09 NTU working with a blue LED at 464 nm and a LOD value of 0.1 NTU working with an IR LED.     

Fibre coupled micro-light emitting diode array light source with integrated band-pass filter for fluorescence detection in miniaturised analytical systems

In this work, a new type of miniaturized fibre-coupled solid-state light source is demonstrated as an excitation source for fluorescence detection in capillary electrophoresis. It is based on a parabolically shaped micro-light emitting diode (μ-LED) array with a custom band-pass optical interference filter (IF) deposited at the back of the LED substrate. The GaN μ-LED array consisted of 270 individual μ-LED elements with a peak emission at 470 nm, each about 14 μm in diameter and operated as a single unit. Light was extracted through the transparent substrate material, and coupled to an optical fibre (OF, 400 μm in diameter, numerical aperture NA = 0.37), to form an integrated μ-LED-IF-OF light source component. This packaged μ-LED-IF-OF light source emitted approximately 225 μW of optical power at a bias current of 20 mA. The bandpass IF filter was designed to reduce undesirable LED light emissions in the wavelength range above 490 nm. Devices with and without IF were compared in terms of the optical power output, spectral characteristics as well as LOD values. While the IF consisted of only 7.5 pairs (15 layers) of SiO₂/HfO₂ layers, it resulted in an improvement of the baseline noise as well as the detection limit measured using fluorescein as test analyte, both by approximately one order of magnitude, with a LOD of 1 × 10⁻⁸ mol L⁻¹ obtained under optimised conditions. The μ-LED-IF-OF light source was then demonstrated for use in capillary electrophoresis with fluorimetric detection. The limits of detection obtained by this device were compared to those obtained with a commercial fibre coupled LED device.     

An integrated light emitting diode-induced fluorescence detector for capillary electrophoresis

An integrated light emitting diode (LED)-induced fluorescence detector was described and evaluated. The LED and its related components including lens and interference filter, the optical fiber used to collect fluorescence, and the capillary column are integrated into a substrate block, which eliminates the need of align procedure of the fiber and the capillary. Forty-fold enhancement of sensitivity was obtained compared with our previous work and the detection limit for fluorescein was 5 nM. Application of the detector for the analysis of FITC-labeled Ephedrine extract was demonstrated.     

Fast transient infrared studies in material science: development of a novel low dead-volume, high temperature DRIFTS cell

A prototype DRIFTS flow reaction chamber was designed and developed in order to find analytical application in the study of heterogeneous catalysts operating at high temperatures under fast transient gas feed conditions. Minimisation of dead-volumes allows gas replacement in 8-10 s at 10 mL min⁻¹ total flow. To overcome problems related to the reactivity of the cell walls under alternating oxidizing/reducing gases, the cell was built with Inconel 600™, which was tested to be very inert even at high temperatures. The sample holder, which was developed to closely resemble a micro plug-flow reactor, poses some problems in terms of heat transfer to the outer body of the cell (limiting then the maximum reachable temperature) and of the correct measurement of the actual sample temperature. These problems were solved with a careful re-design of the upper part of the cell. The second prototype thus derived is able to reach temperatures up to 803 K and allows gas replacement in less than 4 s at 10 mL min⁻¹. The cell is inserted in a MCT-FT-IR, which allows to collect high quality spectra with a 1 s time-resolution. The downstream flow can be analysed by a quadrupole mass spectrometer equipped with an enclosed source and by a commercial GC. The performances of this prototype cell are presented showing some tests carried out with ceria-zirconia (Ce_xZr_1−xO₂) catalysts for CO abatement under real operando conditions.     

An integrated portable hand-held analyser for real-time isothermal nucleic acid amplification

A compact hand-held heated fluorometric instrument for performing real-time isothermal nucleic acid amplification and detection is described. The optoelectronic instrument combines a Printed Circuit Board/Micro Electro Mechanical Systems (PCB/MEMS) reaction detection/chamber containing an integrated resistive heater with attached miniature LED light source and photo-detector and a disposable glass waveguide capillary to enable a mini-fluorometer. The fluorometer is fabricated and assembled in planar geometry, rolled into a tubular format and packaged with custom control electronics to form the hand-held reactor. Positive or negative results for each reaction are displayed to the user using an LED interface. Reaction data is stored in FLASH memory for retrieval via an in-built USB connection. Operating on one disposable 3 V lithium battery >12, 60 min reactions can be performed. Maximum dimensions of the system are 150 mm (h) × 48 mm (d) × 40 mm (w), the total instrument weight (with battery) is 140 g. The system produces comparable results to laboratory instrumentation when performing a real-time nucleic acid sequence-based amplification (NASBA) reaction, and also displayed comparable precision, accuracy and resolution to laboratory-based real-time nucleic acid amplification instrumentation. A good linear response (R² = 0.948) to fluorescein gradients ranging from 0.5 to 10 μM was also obtained from the instrument indicating that it may be utilized for other fluorometric assays. This instrument enables an inexpensive, compact approach to in-field genetic screening, providing results comparable to laboratory equipment with rapid user feedback as to the status of the reaction.     

The development of a multi-nitroimidazole residue analysis assay by optical biosensor via a proof of concept project to develop and assess a prototype test kit

An assay based on optical biosensor technology has been developed to detect a broad range of nitroimidazole drug residues and their metabolites (dimetridazole (DMZ), metronidazole (MNZ), ronidazole (RNZ), hydroxymetronidazole (HO-MNZ) and hydroxydimetridazole (HO-DMZ)) in chicken muscle. The detection limit for the procedure was determined as 0.5 ppb for DMZ and detection capabilities (CCβs) ranged from <1 ppb for DMZ, MNZ and RNZ to <2 ppb for HO-MNZ and HO-DMZ. Intra-assay variation (n = 6) was calculated as 11.6% at a concentration of 1 ppb DMZ and 4.7% at a concentration of 2 ppb DMZ. Inter-assay variation (n = 3) was determined to be 14.2% at a concentration of 1 ppb DMZ and 3.5% at a concentration of 2 ppb DMZ.A prototype kit based on this assay was produced and a multinational study was undertaken to independently evaluate its performance. The resulting data showed that the kit can be implemented with little difficulty in laboratories of varying expertise and is sensitive enough to meet the standards required by international law. Feedback from this study led to the incorporation of some minor improvements to the kit. The commercial partner in the project, XenoSense Ltd., was consulted with regards to producing a commercial test kit based on the prototype assay. As feedback from the collaborative study had been positive with respect to speed, ease of use and performance of the kit, the decision to commercialise the kit was taken. In conclusion, the prototype nitroimidazole kit was shown to offer numerous advantages over existing analytical techniques.     

Photoactivation by visible light of CdTe quantum dots for inline generation of reactive oxygen species in an automated multipumping flow system

Quantum dots (QD) are semiconductor nanocrystals able to generate free radical species upon exposure to an electromagnetic radiation, usually in the ultraviolet wavelength range. In this work, CdTe QD were used as highly reactive oxygen species (ROS) generators for the control of pharmaceutical formulations containing epinephrine. The developed approach was based on the chemiluminometric monitoring of the quenching effect of epinephrine on the oxidation of luminol by the produced ROS. Due to the relatively low energy band-gap of this chalcogenide a high power visible light emitting diode (LED) lamp was used as photoirradiation element and assembled in a laboratory-made photocatalytic unit. Owing to the very short lifetime of ROS and to ensure both reproducible generation and time-controlled reaction implementation and development, all reactional processes were implemented inline by using an automated multipumping micro-flow system. A linear working range for epinephrine concentration of up to 2.28 × 10⁻⁶ mol L⁻¹ (r = 0.9953; n = 5) was verified. The determination rate was about 79 determinations per hour and the detection limit was about 8.69 × 10⁻⁸ mol L⁻¹. The results obtained in the analysis of epinephrine pharmaceutical formulations by using the proposed methodology were in good agreement with those furnished by the reference procedure, with relative deviations lower than 4.80%.     

Integrated chemical sensor array platform based on a light emitting diode, xerogel-derived sensor elements, and high-speed pin printing

We report a new, solid-state, integrated optical array sensor platform. By using pin printing technology in concert with sol-gel-processing methods, we form discrete xerogel-based microsensor elements that are on the order of 100 μm in diameter and 1 μm thick directly on the face of a light emitting diode (LED). The LED serves as the light source to excite chemically responsive luminophores sequestered within the doped xerogel microsensors and the analyte-dependent emission from within the doped xerogel is detected with a charge coupled device (CCD). We overcome the problem of background illumination from the LED reaching the CCD and the associated biasing that results by coating the LED first with a thin layer of blue paint. The thin paint layer serves as an optical filter, knocking out the LEDs red-edge spectral tail. The problem of the spatially-dependent fluence across the LED face is solved entirely by performing ratiometric measurements. We illustrate the performance of the new sensor scheme by forming an array of 100 discrete O₂-responsive sensing elements on the face of a single LED. The combination of pin printing with an integrated sensor and light source platform results in a rapid method of forming (∼1 s per sensor element) reusable sensor arrays. The entire sensor array can be calibrated using just one sensor element. Array-to-array reproducibly is <8%. Arrays can be formed using single or multiple pins with indistinguishable analytical performance.     

Determination of nitrate in mineral water and sausage samples by using a renewable in situ copper modified electrode

A new approach for in situ electrodeposition of a renewable copper layer onto a copper electrode is reported. The active surface was obtained by anodic dissolution of a copper electrode at an appropriate potential and further redeposition of copper ions still remaining at the diffusion layer. Under optimal experimental conditions the peak current response increases linearly with nitrate concentration over a range of 0.1-2.5 mmol L⁻¹. The repeatability of measurements for nitrate was evaluated as 1.8% (N = 15) and the limit of detection of the method was found to be 11 μmol L⁻¹ (S/N = 3). Nitrate contents in two different samples (mineral water and sausages) compared well with those obtained from using the standard Griess protocol at a 95% of confidence level measured by the t-student test. The interference from chloride on the nitrate analysis and the possibility of simultaneous determination of nitrite were also examined.     

Application of thiophene-2-carbaldehyde-modified mesoporous silica as a new sorbent for separation and preconcentration of palladium prior to inductively coupled plasma atomic emission spectrometric determination

A new and efficient method was described for an easy synthesis of functionalized mesoporous silica (MCM-41) using thiophene-2-carbaldehyde. This new chemically bonded analytical reagent was used as an effective sorbent for the solid phase extraction of palladium(II) ion from aqueous solutions. Conditions for effective adsorption of trace levels of palladium concentration were optimized with respect to different experimental parameters in batch process. Thiourea solution could efficiently elute adsorbed palladium(II) ion from the surface of the sorbent which then was determined by inductively coupled plasma atomic emission spectrometer (ICP-AES).Common coexisting ions did not interfere with the separation and determination. The preconcentration factor was 100 (1 ml elution volume) for a 100 ml sample volume. The limit of detection of the proposed method is 0.2 ng ml⁻¹. The maximum sorption capacity of sorbent under optimum conditions has been found to be 5 mg of palladium per gram of sorbent. The relative standard deviation under optimum conditions was 3.2% (n = 10). Accuracy and application of the method was estimated by using test samples of natural and synthetic water spiked with different amounts of palladium(II) ion.     

Highly selective determination of methylmercury with methylmercury-imprinted polymers

In this paper a new prototype of solid phase microextraction-ion mobility spectrometry (SPME-IMS) system was developed to effectively couple the extraction efficiency of SPME with the detection capability of IMS. The main component of this system was the transfer line/desorber, which was a low-thermal-mass (ca. 0.15 g) silicosteel coatings stainless steel tube. The transfer line/desorber was designed to rapidly desorb and transfer the analytes extracted by SPME to IMS. A custom-made temperature controller with a proportional-integral-differential (PID) was used to maintain the temperature of the transfer line/desorber stable and avoid overheating or oscillating. The low thermal mass of this interface allowed it to be rapidly heated and cooled with much less electrical power and could substantially reduce the demand for high capacity batteries. The operational characteristics of this system were demonstrated through the analysis of camphor vapour. The precision of reduced mobility and the peak amplitude of camphor were good (R.S.D. 0.62%, n = 10; R.S.D. 2.5%, n = 10, respectively). SPME-IMS system was also shown to be capable of on-site measurement by monitoring the biogenic volatile organic compounds (BVOCs) emitted from eucalyptus citriodora leaves. In addition, this system was applied to quantitation of diazepam and cocaine in aqueous solution. Limits of detection were 10 ng/mL for diazepam and 50 ng/mL for cocaine with the reported experimental conditions. This SPME-IMS system exhibits considerable promise as a robust, simple, rapid, energy-saving fieldable approach for on-site analysis of analytes in various matrix.     

Enhancement of signal-to-noise level by synchronized dual wavelength modulation for light emitting diode fluorimetry in a liquid-core-waveguide microfluidic capillary electrophoresis system

The signal-to-noise level of light emitting diode (LED) fluorimetry using a liquid-core-waveguide (LCW)-based microfluidic capillary electrophoresis system was significantly enhanced using a synchronized dual wavelength modulation (SDWM) approach. A blue LED was used as excitation source and a red LED as reference source for background-noise compensation in a microfluidic capillary electrophoresis (CE) system. A Teflon AF-coated silica capillary served as both the separation channel and LCW for light transfer, and blue and red LEDs were used as excitation and reference sources, respectively, both radially illuminating the detection point of the separation channel. The two LEDs were synchronously modulated at the same frequency, but with 180°-phase shift, alternatingly driven by a same constant current source. The LCW transferred the fluorescence emission, as well as the excitation and reference lights that strayed through the optical system to a photomultiplier tube; a lock-in amplifier demodulated the combined signal, significantly reducing its noise level. To test the system, fluorescein isothiocyanate (FITC)-labeled amino acids were separated by capillary electrophoresis and detected by SDWM and single wavelength modulation, respectively. Five-fold improvement in S/N ratio was achieved by dual wavelength modulation, compared with single wavelength modulation; and over 100-fold improvement in S/N ratio was achieved compared with a similar LCW-CE system reported previously using non-modulated LED excitation. A detection limit (S/N = 3) of 10 nM FITC-labeled arginine was obtained in this work. The effects of modulation frequency on S/N level and on the rejection of noise caused by LED-driver current and detector were also studied.     

Microfluidic liquid-liquid extraction system based on stopped-flow technique and liquid core waveguide capillary

In this work, a miniaturized liquid-liquid extraction system under stopped-flow manipulation mode with spectrometric detection was developed. A Teflon AF liquid-core waveguide (LCW) capillary was used to serve as both extraction channel for organic solvent flow and adsorption detection flow cell. Gravity induced hydrostatic pressure was used to drive the organic and aqueous phases through the extraction channels. During extraction process, a stable organic and aqueous phase interface was formed at the outlet of the capillary, through which the analyte in the flowing aqueous stream was extracted into the stationary organic solvent in capillary. The absorbance of the analyte extracted into the organic solvent was measured in situ by a spectrometric detection system with light emitting diode (LED) as light source and photodiode as absorbance detector. The performance of the system was demonstrated in the determination of sodium dodecyl sulfate (SDS) extracted as an ion pair with methylene blue into chloroform. The precision of the measured absorbance for a 5 mg L⁻¹ SDS standard was 6.1% R.S.D. (n = 5). A linear response range of 1-10 mg L⁻¹ SDS was obtained with 5 min extraction period. The limit of detection (LOD) for SDS based on three times standard deviation of the blank response was 0.25 mg L⁻¹.     

Immuno-capture and in situ detection of Salmonella typhimurium on a novel microfluidic chip

The new method presented in this article achieved the goal of capturing Salmonella typhimurium via immunoreaction and rapid in situ detection of the CdSe/ZnS quantum dots (QDs) labeled S. typhimurium by self-assembly light-emitting diode-induced fluorescence detection (LIF) microsystem on a specially designed multichannel microfluidic chip. CdSe/ZnS QDs were used as fluorescent markers improving detection sensitivity. The microfluidic chip developed in this study was composed of 12 sample channels, 3 mixing zones, and 6 immune reaction zones, which also acted as fluorescence detection zones. QDs–IgG–primary antibody complexes were generated by mixing CdSe/ZnS QDs conjugated secondary antibody (QDs–IgG) and S. typhimurium antibody (primary antibody) in mixing zones. Then, the complexes went into immune reaction zones to label previously captured S. typhimurium in the sandwich mode. The capture rate of S. typhimurium in each detection zone was up to 70%. The enriched QDs-labeled S. typhimurium was detected using a self-assembly LIF microsystem. A good linear relationship was obtained in the range from 3.7 × 10 to 3.7 × 10⁵ cfu mL⁻¹ using the equation I = 0.1739 log (C) − 0.1889 with R² = 0.9907, and the detection limit was down to 37 cfu mL⁻¹. The proposed method of online immunolabeling with QDs for in situ fluorescence detection on the designed multichannel microfluidic chip had been successfully used to detect S. typhimurium in pork sample, and it has shown potential advantages in practice.     

Fingerprint analysis of Dioscorea nipponica by high-performance liquid chromatography with evaporative light scattering detection

High-performance liquid chromatographic method (HPLC) with evaporative light scattering detection (ELSD) coupled with microwave-assisted extraction (MAE) as an efficient sample preparation technique has been developed for fingerprint analysis of Dioscorea nipponica. The samples were separated with an Agilent C8 column using water (A) and acetonitrile (B) under gradient conditions (0-10 min, linear gradient 20-40% B; 10-12 min, linear gradient 40-42% B; 12-25 min, isocratic 42% B) as the mobile phase at a flow rate of 1 mL min⁻¹ within 22 min. The ELSD conditions were optimized at nebulizer-gas flow rate 2.7 L min⁻¹ and drift tube temperature 90 °C. Precision experiments showed relative standard deviation (R.S.D.) of peak area and retention time were better than 2.5%; inter-day and intra-day variabilities showed that R.S.D. was ranged from 0.78% to 4.74%. Limit of detection was less than 50 μg mL⁻¹ and limit of quantification was less than 80 μg mL⁻¹. Accuracy validation showed that average recovery was between 97.39% and 104.07%. The method was validated to achieve the satisfactory precision and recovery. Relative retention time and relative peak area were used to identify the common peaks for fingerprint analysis. There are nine common peaks in the fingerprint. The quality of seven batches of D. nipponica samples was evaluated to be qualified or unqualified by the parameters “difference” and “total difference” of common peaks. Furthermore, the contents of important medicinal compounds (dioscin, prodioscin and gracillin) in different batches of D. nipponica samples were determined simultaneously using the developed HPLC-ELSD method. The results indicated variation of the herb quality which might be related to different producing area, growing condition, climate, harvest time, drug processing and so on. The developed analytical procedure was proved to be a reliable and rapid method for the quality control of D. nipponica.     

Capillary scale liquid core waveguide based fluorescence detectors for liquid chromatography and flow analysis

A versatile, simple, liquid core waveguide (LCW)-based fluorescence detector design is described for capillary systems. A Teflon AF coated fused silica capillary serves as the LCW. The LCW is transversely excited. The light source can be a conventional or high power (HP) light emitting diode (LED) or a laser diode (LD). The source can be coupled to the LCW directly or via an optical fiber. Fiber coupling is convenient if a high power (necessarily heat sink mounted) emitter is used. The LCW is concentrically placed within a slightly larger opaque jacket tube and the LCW terminates just short of the jacket terminus, which is sealed with an optical window. The influent liquid thus exits the LCW tip, flows back around the LCW through the jacket annulus to exit via an aperture on the jacket tube. The problem of coupling the emitted light efficiently to the photodetector is thus solved by placing the tip of the annular tubular assembly directly on the detector.For excitation wavelengths of 365 nm (LED/HPLED) and 405 nm (LD), the tris(8-hydroxyquinoline-5-sulfonic acid (sulfoxine)) chelate of aluminum (λ_em,max ∼ 500 nm) and Coumarin 30 were respectively used as the model analyte. For source-detector combinations comprising (a) a UV LED (∼1.5 mW @ 15 mA) and a photodiode, (b) a LD (∼5 mW, abstracted from a “Blu-Ray” recorder) and a miniature photomultiplier tube (mPMT), and (c) a high power (210 mW @ 500 mA) surface-mount HPLED-mPMT, the S/N = 3 LODs were, respectively, 1.7 pmol Al, 3-100 fmol Coumarin 30 (depending on laser intensity and integration time), and 4 fmol Al. In the last case, the relative standard derivation (R.S.D.) at the 20 fmol level was 1.5% (n = 10).     

Cadmium (II) imprinted 3-mercaptopropyltrimethoxysilane coated stir bar for selective extraction of trace cadmium from environmental water samples followed by inductively coupled plasma mass spectrometry detection

Cd(II) imprinted 3-mercaptopropyltrimethoxysilane (MPTS)-silica coated stir bar was prepared by sol–gel technique combining with a double-imprinting concept for the first time and was employed for stir bar sorptive extraction (SBSE) of trace Cd(II) from water samples followed by inductively coupled plasma mass spectrometry (ICP-MS) detection. A tetramethoxysilane (TMOS) coating was first in situ created on the glass bar surface. Afterward, a sol solution containing MPTS as the functional precursor, ethanol as the solvent and both Cd(II) and surfactant micelles (cetyltrimethylammonium bromide, CTAB) as the template was again coated on the TMOS bar. The structures of the stir bar coating were characterized by FT-IR spectroscopy. Round-bottom vial was used for the extraction of Cd(II) by SBSE to avoid abrasion of stir bar coatings. The factors affecting the extraction of Cd(II) by SBSE such as pH, stirring rate and time, sample/elution volume and interfering ions have been investigated in detail, and the optimized experimental parameters were obtained. Under the optimized conditions, the adsorption capacities of non-imprinted and imprinted coating stir bars were found to be 0.5 μg and 0.8 μg bar⁻¹. The detection limit (3σ) based on three times standard deviations of the method blanks by 7 replicates was 4.40 ng L⁻¹ and the relative standard deviation (RSD) was 3.38% (c = 1 μg L⁻¹, n = 7). The proposed method was successfully applied for the analysis of trace Cd(II) in rain water, East Lake and Yangtze River water. To validate the proposed method, certified reference material of GSBZ 50009-88 environmental water was analyzed and the determined value is in a good agreement with the certified value. The developed method is rapid, selective, sensitive and applicable for the analysis of trace Cd(II) in environmental water samples.