Adhesion of biologically inspired vertical and angled polymer microfiber arrays

This paper proposes an approximate adhesion model for fibrillar adhesives for developing a fibrillar adhesive design methodology and compares numerical simulation adhesion results with macroscale adhesion data from polymer microfiber array experiments. A technique for fabricating microfibers with a controlled angle is described for the first time. Polyurethane microfibers with different hardnesses, angles, and aspect ratios are fabricated using optical lithography and polymer micromolding techniques and tested with a custom tensile adhesion measurement setup. Macroscale adhesion and overall work of adhesion of the microfiber arrays are measured and compared with the models to observe the effect of fiber geometry and preload. The adhesion strength and work of adhesion behavior of short and long vertical and long angled fiber arrays have similar trends with the numerical simulations. A scheme is also proposed to aid in optimized fiber adhesive design.     

Encasement of metallic cardiovascular stents with endothelial cell‐selective copolyetheresterurethane microfibers

Cardiovascular metallic stents established in clinical application are typically coated by a thin polymeric layer on the stent struts to improve hemocompatibility, whereby often a drug is added to the coating to inhibit neointimal hyperplasia. Besides such thin film coatings recently nano/microfiber coated stents are investigated, whereby the fibrous coating was applied circumferential on stents. Here, we explored whether a thin fibrous encasement of metallic stents with preferentially longitudinal aligned fibers and different local fiber densities can be achieved by electrospinning. An elastic degradable copolyetheresterurethane, which is reported to selectively enhance the adhesion of endothelial cells, while simultaneously rejecting smooth muscle cells, was utilized for stent coating. The fibrous stent encasements were microscopically assessed regarding their single fiber diameters, fiber covered area and fiber alignment at three characteristic stent regions before and after stent expansion. Stent coatings with thicknesses in the range from 30 to 50 µm were achieved via electrospinning with 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFP)‐based polymer solution, while a mixture of HFP and formic acid as solvent resulted in encasements with a thickness below 5 µm comprising submicron sized single fibers. All polymeric encasements were mechanically stable during expansion, whereby the fibers deposited on the struts remained their position. The observed changes in fiber density and diameter indicated diverse local deformation mechanisms of the microfibers at the different regions between the struts. Based on these results it can be anticipated that the presented fibrous encasement of stents might be a promising alternative to stents with polymeric strut coatings releasing anti‐proliferative drugs. Copyright © 2015 John Wiley & Sons, Ltd.     

Degradation behavior of electrospun microfibers of blends of poly(lactide-co-glycolide) and Pluronic F-108

Electrospun poly(dl-lactide-co-glycolide) (PLGA) microfibers have been explored as extra cellular matrix mimicking scaffolding systems for tissue engineering application. However, the hydrophobic nature of PLGA can be limiting in terms of protein adsorption. Hence, blending of PLGA with a hydrophilic polymer (Pluronic^®) prior to electrospinning has been explored as a potential strategy to impart hydrophilicity to PLGA microfibers. In this study, PLGA (85/15) was blended with small quantities (0.5-2% w/v) of Pluronic^® F-108 (PF-108) and electrospun into microfibers. Blending of PF-108 demonstrated a significant decrease in the surface hydrophilicity of microfibers as was evidenced by an increase in wetting tension. Surface analysis using XPS indicated the presence of PF-108 in the bulk of the fibers in addition to the surface of the fibers. The results of the water uptake studies indicated that the water uptake capacity and consequential fiber swelling was significantly increased in the presences of PF-108. The in vitro degradation studies demonstrated that the trend in molecular weight loss was not significantly influenced by the presence of small quantities of PF-108. Therefore, blending of PLGA with PF-108 could be an effective technique for surface modification of electrospun PLGA microfibers without compromising on the other advantages of PLGA.     

Si(111)-7×7表面上C60多层膜的生长及其纳米摩擦学性质

在超高真空(UHV)条件下,用分子束外延(MBE)方法,通过对生长过程中蒸发速率和衬底温度等参数的控制,可以避免C60分子在Si(111)-7×7重构表面多层生长时团聚岛的形成,得到了逐层生长的C60多层膜.同时利用超高真空扫描隧道显微镜(UHV-STM)对这种多层膜结构进行了观察并对这种现象产生的机理做了分析,测定了不同层数C60薄膜的黏附力和摩擦力曲线,发现分子层数对薄膜的摩擦性质有显著影响,随着沉积层数的增加,样品的摩擦力明显降低,摩擦系数也有降低的趋势.由于分子层数的增加导致C60分子转动程度增强,本文得出结论,摩擦力的降低是由C60分子的转动引起的,C60分子在这里充当了“纳米滚动轴承”,即C60分子的转动为微观结构提供了能量耗散通道.     

Chemical force spectroscopy in heterogeneous systems: intermolecular interactions involving epoxy polymer,mixed monolayers,and polar solvents

We used chemical force microscopy (CFM) to study adhesive forces between surfaces of epoxy resin and self-assembled monolayers (SAMs) capable of hydrogen bonding to different extents. The influence of the liquid medium in which the experiments were carried out was also examined systematically. The molecular character of the tip, polymer, and liquid all influenced the adhesion. Complementary macroscopic contact angle measurements were used to assist in the quantitative interpretation of the CFM data. A direct correlation between surface free energy and adhesion forces was observed in mixed alcohol-water solvents. An increase in surface energy from 2 to 50 mJ/m(2) resulted in an increase in adhesion from 4-8 nN to 150-300 nN for tips with radii of 50-150 nm. The interfacial surface energy for identical nonpolar surface groups of SAMs was found not to exceed 2 mJ/m(2). An analysis of adhesion data suggests that the solvent was fully excluded from the zone of contact between functional groups on the tip and sample. With a nonpolar SAM, the force of adhesion increased monotonically in mixed solvents of higher water content; whereas, with a polar SAM (one having a hydrogen bonding component), higher water content led to decreased adhesion. The intermolecular force components theory was used for the interpretation of adhesion force measurements in polar solvents. Competition between hydrogen bonding within the solvent and hydrogen bonding of surface groups and the solvent was shown to provide the main contribution to adhesion forces. We demonstrate how the trends in the magnitude of the adhesion forces for chemically heterogeneous systems (solvents and surfaces) measured with CFM can be quantitatively rationalized using the surface tension components approach. For epoxy polymer, inelastic deformations also contributed heavily to measured adhesion forces.     

Structure and nanomechanical characterization of electrospun PS/clay nanocomposite fibers

Electrospinning has been emerging as one of the most efficient methods to fabricate polymer nanofibers. In this paper, PS/clay nanocomposite fibers with varying diameters were electrospun onto solid substrates. The fiber diameters were adjusted from 4 microm to 150 nm by changing the solution concentration. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM) were used to characterize the fiber morphology. Shear modulation force microscopy (SMFM) was utilized to investigate the surface nanomechanical properties of electrospun fibers as a function of the fiber diameter and temperature. In the absence of clay, no change in T(g) was observed, even though a large increase of shear modulus below the glass transition temperature was found. This effect was postulated to result from the molecular chain alignment during electrospinning. The addition of functionalized clays to the spinning solution produced fibers with a highly aligned montmorillonite layer structure at a clay concentration of 4 wt %. Clay agglomerates were observed at higher concentrations. The existence of clay further enhanced the shear modulus of fibers and increased the glass transition temperature by nearly 20 degrees C.     

Microfiber Fabricated via Microfluidic Spinning toward Tissue Engineering Applications

Microfibers, a type of long, thin, and flexible material, can be assembled into functional 3D structures by folding, binding, and weaving. As a novel spinning method, combining microfluidic technology and wet spinning, microfluidic spinning technology can precisely control the size, morphology, structure, and composition of the microfibers. Particularly, the process is mild and rapid, which is suitable for preparing microfibers using biocompatible materials and without affecting the viability of cells encapsulated. Furthermore, owing to the controllability of microfluidic spinning, microfibers with well-defined structures (such as hollow structures) will contribute to the exchange of nutrients or guide cell orientation. Thus, this method is often used to fabricate microfibers as cell scaffolds for cell encapsulation or adhesion and can be further applied to biomimetic fibrous tissues. In this review, the focus is on different fiber structures prepared by microfluidic spinning technology, including solid, hollow, and heterogeneous structures, generated from three essential elements: spinning platform, fiber composition, and solidification methods. Furthermore, the application of microfibers is described with different structures in tissue engineering, such as blood vessels, skeletal muscle, bone, nerves, and lung bronchi. Finally, the challenges and future development prospects of microfluidic spinning technology in tissue engineering applications are discussed.     

Melting Temperature of Individual Electrospun Poly(vinylidene fluoride) Fibers Studied by AFM-based Local Thermal Analysis

Thermal properties such as melting temperature can well reflect the microstructure of the polymer material, and have practical implications in the application of nanofibers. In this work, we investigated the melting temperature of individual electrospun poly(vinylidene fluoride)(PVDF) nanofibers with diameters ranging from smaller than 200 nm to greater than 2 μm by the local thermal analysis technique. The PVDF fibers obtained under four different conditions were found to crystallize into α and β phases, and the fiber mats showed typical values in the crystallinity and T_m with no significant difference among the four. However, analyses at single fiber level revealed broad distribution in diameter and T_m for the fibers produced under identical electrospinning condition. The T_m of individual nanofibers was found to remain constant at large diameters and increase quickly when reducing the fiber diameter toward the nanoscale, and T_m values of 220-230 ℃ were observed for the thinnest nanofibers, much higher than the typical values reported for bulk PVDF. The T_m and molecular orientation at different positions along a beaded fiber were analyzed, showing a similar distribution pattern with a minimum at the bead center and higher values when moving toward both directions. The results indicate that molecular orientation is the driving mechanism for the observed correlation between the T_m and the diameter of the nanofibers.     

In situ polymerization of aniline in electrospun microfbers简

Conductive microfibers with an average diameter of ca. 1.0 mm were prepared by in situ polymerization of aniline, in which poly(vinylchloride-acrylonitrile)(PVC-AN) was used as the filament-material in electrospinning to form precursor microfibers and carry the aniline monomers. Fourier-transform infrared(FTIR) results demonstrated that PANi was successfully polymerized in the microfibers. The morphology of the PVC-AN-PANi microfibers was observed by scanning electron microscopy(SEM). Results of differential scanning calorimetry indicated that the polymer composite of PVC-AN-PANi formed via molecular interactions. Although the conductivity of PVC-AN-PANi microfibers was still limited(2.2 fi 10à8S/cm), this method provided an effective and convenient approach for preparing highly uniform and soft microfibrous electrodes.     

Single‐Step Electrospinning of Bimodal Fiber Meshes for Ease of Cellular Infiltration

Bimodal fiber meshes with fiber diameters differing by one order of magnitude, are electrospun in a simple one‐step process, using a standard single syringe electrospin setup. The nano‐ and microfiber meshes combine the benefits of nanofibers (cell adhesion, proliferation) with those of microfibers (open structure, large pore size) and are therefore interesting as scaffolds for cellular infiltration.

     

Study of the carbon fiber–poly(ether–ether–ketone) (PEEK) interfaces, 2: relationship between interfacial shear strength and adhesion energy

In the second part of this general study, the carbon fiber–PEEK interfacial shear strength is measured by means of a fragmentation test on single-fiber composites. Different thermal treatments (continuous cooling from the melt, isothermal treatments and long melting temperature time) are applied to these model composites prior to testing. The results are systematically compared with the previously determined reversible work of adhesion between carbon fiber and PEEK. It is shown that physical interactions at the interface determine, to a large extent, the magnitude of the interfacial shear strength between both materials. However, it appears that the magnitude of the stress transfer from the matrix to the fiber is affected either by the existence of an interfacial layer or by a preferential orientation of the polymer chains near the fiber surface. The results obtained on systems that have been subjected to isothermal treatments (isothermal crystallization of PEEK) seem to confirm the existence of a transcrystalline interphase, the properties of which are dependent upon the crystallization rate of the matrix and the interfacial adhesion energy.     

Field‐Driven Surface Segregation of Biofunctional Species on Electrospun PMMA/PEO Microfibers

The need to biofunctionalize polymer surfaces for targeted bio‐related applications continues to grow, and efforts designed to meet this need rely heavily on surface grafting or polymerization. In this study, we provide a viable alternative by demonstrating that the peptide segment of a polymer‐peptide conjugate can be selectively driven to the surface of polymer nano/microfibers during electrospinning due to contrast in polarizability. Judicious choice of the polymer sequence in the conjugate permits use of the conjugate with compatible fiber‐forming polymers. Here, we use a water soluble poly(ethylene oxide)‐containing conjugate in combination with a hydrophobic thermoplastic, poly(methyl methacrylate). Surface enrichment is measured by X‐ray photoelectron spectroscopy, and fiber morphology is investigated by electron microscopy. Microfibers generated from the blends examined here are largely resistant to long term water immersion and are thus suited as support scaffolds or filtration membranes.

     

Design,Preparation and Properties of Bio-inspired Hierarchical Structure Yarns with Enhanced Thermal Insulation and Water Transfer Ability

Encouraged by the porous and stable structure of cold-resist animals' hair or feather, bio-inspired hierarchical structure yarns combining polyacrylonitrile(PAN) nanofibers and polypropylene(PP) hollow microfibers have been developed by a modified conjugate electrospinning technology. Physical cross-linking has been built to increase fibers adhesion and construct interlayer support for nanofibrous assembly. The nanofibers and hollow microfibers construct a stable porous structure with porosity of 62%, providing excellent thermal insulating ability[temperature diffe-rence(|ΔT|) between skin and yarn surface is 4.9℃] as well as good mechanical property. More interestingly, the water transfer ability (infiltrate the yarn in 10 s) of synthetic fibers has been improved greatly by the combination of thin diameter nanofibers to the yarn. It is believed that the research lays the foundation for bio-inspired engineering technology in the manufacture of thermal comfort.     

Coatings of polyethylene glycol for suppressing adhesion between solid microspheres and flat surfaces

This article describes the development and the examination of surface coatings that suppress the adhesion between glass surfaces and polymer microspheres. Superparamagnetic doping allowed for exerting magnetic forces on the microbeads. The carboxyl functionalization of the polymer provided the means for coating the beads with polyethylene glycol (PEG) with different molecular weight. Under gravitational force, the microbeads settled on glass surfaces with similar polymer coatings. We examined the efficacy of removing the beads from the glass surfaces by applying a pulling force of ~1.2 pN. The percent beads remaining on the surface after applying the pulling force for approximately 5 s served as an indication of the adhesion propensity. Coating of PEG with molecular weight ranging between 3 and 10 kDa was essential for suppressing the adhesion. For the particular substrates, surface chemistry and aqueous media we used, coatings of 5 kDa manifested optimal suppression of adhesion: that is, only 3% of the microbeads remained on the surface after applying the pulling magnetic force. When either the glass or the beads were not PEGylated, the adhesion between them was substantial. Addition of a noncharged surfactant, TWEEN, above its critical micelle concentrations (CMCs) suppressed the adhesion between noncoated substrates. The extent of this surfactant-induced improvement of the adhesion suppression, however, did not exceed the quality of preventing the adhesion that we attained by PEGylating both substrates. In addition, the use of surfactants did not significantly improve the suppression of bead-surface adhesion when both substrates were PEGylated. These findings suggest that such surfactant additives tend to be redundant and that covalently grafted coatings of PEGs with selected chain lengths provide sufficient suppression of nonspecific interfacial interactions.     

Effect of surface treatment on the Hamaker constant of intermediate modulus carbon fibers

The Hamaker constant of unsized intermediate modulus carbon fibers was evaluated by contact angle measurement following the Fowkes theory of interfacial energetics. The effects of a surface treatment (performed by the manufacturer) and an oxygen plasma treatment (performed by us), both of oxidizing nature, proved to slightly increase the value of the Hamaker constant to a level that enhanced by about 9% the Lifshitz-van der Waals contribution to the theoretical adhesion force between the fiber and an epoxy matrix. A possible explanation of the observed increase of the Hamaker constant is the higher contribution to the overall Lifshitz-van der Waals interaction of Keesom (orientation) and Debye (induction) forces.     

Enhanced wet adhesion and shear of elastomeric micro-fiber arrays with mushroom tip geometry and a photopolymerized p(DMA-co-MEA) tip coating

Using principles inspired by the study of naturally occurring sticky systems such as the micro- and nanoscale fibers on the toes of geckos and the adhesive proteins secreted by marine animals such as mussels, this study describes the development and evaluation of a novel patterned and coated elastomeric microfibrillar material for enhanced repeatable adhesion and shear in wet environments. A multistep fabrication process consisting of optical lithography, micromolding, polymer synthesis, dipping, stamping, and photopolymerization is described to produce uniform arrays of polyurethane elastomeric microfibers with mushroom-shaped tips coated with a thin layer of lightly cross-linked p(DMA-co-MEA), an intrinsically adhesive synthetic polymer. Adhesion and shear force characterization of these arrays in contact with a glass hemisphere is demonstrated, and significant pull-off force, overall work of adhesion, and shear force enhancements in submerged aqueous environments are shown when compared to both unpatterned and uncoated samples, as well as previously evaluated patterned and coated arrays with differing geometry. Such materials may have potential value as repeatable adhesives for wet environments, such as for medical devices.     

Assembly of well-aligned multiwalled carbon nanotubes in confined polyacrylonitrile environments: electrospun composite nanofiber sheets

Highly oriented, large area continuous composite nanofiber sheets made from surface-oxidized multiwalled carbon nanotubes (MWNTs) and polyacrylonitrile (PAN) were successfully developed using electrospinning. The preferred orientation of surface-oxidized MWNTs along the fiber axis was determined with transmission electron microscopy and electron diffraction. The surface morphology and height profile of the composite nanofibers were also investigated using an atomic force microscope in tapping mode. For the first time, it was observed that the orientation of the carbon nanotubes within the nanofibers was much higher than that of the PAN polymer crystal matrix as detected by two-dimensional wide-angle X-ray diffraction experiments. This suggests that not only surface tension and jet elongation but also the slow relaxation of the carbon nanotubes in the nanofibers are determining factors in the orientation of carbon nanotubes. The extensive fine absorption structure detected via UV/vis spectroscopy indicated that charge-transfer complexes formed between the surface-oxidized nanotubes and negatively charged (-CN[triple bond]N:) functional groups in PAN during electrospinning, leading to a strong interfacial bonding between the nanotubes and surrounding polymer chains. As a result of the highly anisotropic orientation and the formation of complexes, the composite nanofiber sheets possessed enhanced electrical conductivity, mechanical properties, thermal deformation temperature, thermal stability, and dimensional stability. The electrical conductivity of the PAN/MWNT composite nanofibers containing 20 wt % nanotubes was enhanced to approximately 1 S/cm. The tensile modulus values of the compressed composite nanofiber sheets were improved significantly to 10.9 and 14.5 GPa along the fiber winding direction at the MWNT loading of 10 and 20 wt %, respectively. The thermal deformation temperature increased with increased MWNT loading. The thermal expansion coefficient of the composite nanofiber sheets was also reduced by more than an order of magnitude to 13 x 10(-6)/ degrees C along the axis of aligned nanofibers containing 20 wt % MWNTs.     

Biodegradable polyesters reinforced with surface-modified vegetable fibers

Flax fibers are investigated as reinforcing agents for biodegradable polyesters (Bionolle and poly(lactic acid) plasticized with 15 wt.-% of acetyltributyl citrate, p-PLLA). The composites are obtained either by high temperature compression molding fiber mats sandwiched between polymer films, or by batch mixing fibers with the molten polymer. Fibers in composites obtained by the latter method are much shorter (140-200 microm) than those of the mats (5,000 microm). Flax fibers are found to reinforce both p-PLLA and Bionolle (i.e. tensile modulus and strength increase) when composites based on fiber mats are investigated. Conversely, analogous composites obtained by batch mixing show poor mechanical properties. The observed behavior is attributed to the combined effect of fiber length and fiber-matrix adhesion. If flax fibers with a modified surface chemistry are used, the strength of short fiber composites is seen to improve significantly because the interface strengthens and load is more efficiently transferred. Appropriate surface modifications are performed by heterogeneous acylation reactions or by grafting poly(ethylene glycol) chains (PEG, molecular weight 350 and 750). The highest tensile strength of p-PLLA composites is reached when PEG-grafted flax fibers are used, whereas in the case of Bionolle the best performance is observed with acylated fibers.     

Influence of adsorbed polymers on the removal of mineral particles from a planar surface

 Experimental results on the role of adsorbed polymers on the particle adhesion are presented. Both Brownian (silica particles) and non-Brownian (glass beads) particles were used. The particles were deposited onto the internal surface of a glass parallelepiped cell, and then submitted to increasing laminar flow rates. The pH and the ionic strength of the electrolytes were fixed. The adhesive force was related to the hydrodynamic force required to dislodge 50% of the initially attached beads. We found that high molecular weight PEO had little effect on the adhesion of small silica beads due to the low affinity of the polymer for silica or glass surfaces. On the contrary, PEO greatly enhanced the adhesion of bigger glass beads forced to deposit on the capillary surface because of gravity. The increase was all the more pronounced as the molecular weight of the polymer was high. The effect of high molecular weight cationic copolymers on the adhesion of silica particles was drastic. The maximal force (1500 pN) applied by the device could not enable any particle detachment even using polymers of low cationicity rate (5%), showing the efficiency of electrostatic attractions. When copolymers were adsorbed on both surfaces (particles and plane), the adhesive force exhibited a maximum at intermediate coverage of particles. This optimum was related to the optimum flocculation concentration classically observed in flocculation of suspensions by polymers. Received: 16 February 1996 Accepted: 10 September 1996     

Electrospun fibers from poly(methyl methacrylate)/vapor grown carbon nanofibers

Electrospinning has been used to obtain poly(methyl methacrylate) (PMMA) microfibers and nanofibers and PMMA/vapor grown carbon nanofibers (VGCNFs or CNFs) composite fibers with micrometer and nanometer size diameters. Thermogravimetric analysis (TGA) indicated that addition of CNFs caused a decrease in the thermal stability of the composite fibers. Scanning electron microscopy (SEM) was used to confirm the micro‐ and nano‐ nature of the fibers and transmission electron microscopy (TEM) was utilized to confirm the presence of CNFs embedded within the polymer matrix and along the surface. Copyright © 2006 John Wiley & Sons, Ltd.