Ti－Si Pentasil型杂原子分子筛的气团相同晶取代法制备及其羟基化性能──Ⅱ．制备条件及母体对钛进入骨架的影响

Ｔｉ－Ｓｉ　Ｐｅｎｔａｓｉｌ型杂原子分子筛的气团相同晶取代法制备及其羟基化性能──Ⅱ．制备条件及母体对钛进入骨架的影响郭新闻，王桂茹，王祥生（大连理工大学工业催化剂研究所，大连１１６０１２）关键词Ｔｉ－ＺＳＭ－５分子筛，杂原子分子筛，气团相同晶取代含...     

Structural description of the Na(2)B(4)O(7)-Na(3)AlF(6)-TiO(2) system. 1. IR and Raman study of the solidified melts

The pseudo-binary Na2B4O7-[Na3AlF6-TiO2]11 system has been investigated at room temperature by means of X-ray diffraction, IR, Raman, and UV-vis spectroscopies. Evolution of the different spectra with Na2B4O7 and TiO2 contents evidenced the breaking-up of the large borate rings in favor of small borate units, the diminution of the BIV fraction, and the partial substitution of oxygen by fluorine with the formation of oxyfluoride species. Two domains of compositions are described: a TiO2-rich region with 20-50% Na2B4O7 with the lowering of boron coordination and formation of Ti(O,F)6 units and a TiO2-poor region with 60-90% Na2B4O7 where the Na3AlF6 modifier behavior is predominant. The enhanced modifier effect of [Na3AlF6-TiO2]11 in comparison with pure Na3AlF6 on the vitreous network of Na2B4O7 consists of fluorine preference for binding to higher strength cations, Ti4+, over Al3+ and Na+ respectively, when TiO2 addition exceeds 5 wt %.     

Synthesis and Characterization of Ti-ZSM-5 in a Non-alkaline Medium in the Presence of Fluoride Ions

Ti-ZSM-5 was synthesized by hydro thermal crystallization in the presence of fluoride via using a non-alkaline medium. pH values were 5~7. SEM showed perfect Ti-ZSM-5 crystals and a large single crystal growing from the favourable medium. Substitution of titanium for silicon in the ZSM-5 framework led to a decrease of crystal size and of the length/width ratio. Electron microprobe analysis indicated a homogeneous distribution of titanium in the ZSM-5 framework. The unit cell parameters of the Ti-ZSM-5 determined by XRD increased with an increase in titanium content in the framework. TiO4tetrahedron vibrations were found in the IR spectrum. Si(1Ti) peakwas seen in the 29Si MAS NMR spectrum at -1O1ppm(from TMS) and 13CMAS NMR analysis verified the effect of (C3H7)4N F- occluded in thechannels. XPS study on the precursors, calcined and H2O2 adsorbed Ti-ZSM-5 was performed and some interesting results were observed.     

不同来源的钛硅沸石的孔结构,酸性和催化性能

用气固相类质同晶取代和水热方法合成了Ｔｉ－ＺＳＭ－５和ＴＳ－１沸石，对它们的组成、孔结构、酸性和催化活性进行了比较。以季铵盐为模板剂水热合成的无铝ＴＳ－１沸石骨架Ｔｉ含量高，表面无强酸位，且随骨架Ｔｉ含量增加，沸石晶内由缺陷造成的二次孔数量增多。类质同晶取代的Ｔｉ－ＺＳＭ－５沸石骨架Ｔｉ含量有限，样品内尚保留部分骨架Ａｌ，沸石表面强弱酸位同时存在。增加沸石骨架Ｔｉ含量和晶内二次孔对提高苯酚过氧化氢     

TiO2／Al2O3负载量对气相酯交换合成碳酸甲丙酯的影响

采用XRD、N2 physical adsorption、XPS、NH3-TPD和吡啶吸附IR等技术,对碳酸二甲酯和丙醇气固相合成碳酸甲丙酯的TiO2/Al2O3催化剂进行了表征.实验结果表明,TiO2/Al2O3表面的Lewis酸中心是反应的催化活性位,酸性主要来源于Al2O3,TiO2起修饰作用,有利于选择性生成碳酸甲丙酯.随着Ti负载量的增加,TiO2在Al2O3表面由高度分散状态向晶态转变,其比表面积逐渐降低,但是TiO2/Al2O3的表面酸性质没有受到显著影响,L酸量先是增加,而后略有下降.当Ti负载量为5%时,DMC的转化率及MPC的选择性分别达到54.3%和88.1%.     

共沉淀法掺杂SiO_2对V_2O_5-WO_3/TiO_2催化剂SCR性能的影响

通过共沉淀法将SiO_2组分掺入到V2O5-WO3/SiO_2-TiO_2催化剂TiO_2载体中,并通过多种物理化学手段,考察了不同SiO_2掺杂量对催化剂结构、表面性质与SCR性能的影响.结果表明,SiO_2掺入到TiO_2中,Si与Ti形成Si—O—Ti键,使催化剂比表面积增加.Si—O—Ti键的生成以及Si Ox物种上的-OH基团使催化剂表面Br?nsted酸增加,但新增的Br?nsted酸对SCR反应不利,并且SiO_2的掺杂也使得V~(5+)含量降低,Si—O—V键合作用使分散的VOx物种更难还原.Si组分以共沉淀法掺入到V_2O_5-WO_3/TiO_2催化剂会造成脱硝活性的显著下降.     

TiCl3-enhanced NaAlH4: impact of excess al and development of the Al1-yTiy phase during cycling

NaAlH(4) with TiCl(3) and Al were mixed by ball-milling and cycled three times. The hydrogen storage properties were monitored during cycling, and the products were characterized by synchrotron X-ray diffraction. Because of the previously described formation of Al(1)(-)(y)Ti(y) with y approximately 0.15 during cycling that traps Al beyond the amount associated with the formation of NaCl, some Na(3)AlH(6) has no free Al to react with to form NaAlH(4). This was counteracted in the present work by adding a stoichiometric amount of Al that increases the theoretical storage capacity. Due to limitations in metal diffusion small amounts of Na(3)AlH(6) were still detected. When approximately 7 mol % more Al than the stoichiometric amount was added, the observed storage capacity increased significantly, and the Na(3)AlH(6) content was negligible after prolonged rehydrogenation. Cycled NaAlH(4) + 10 mol % TiCl(3) were desorbed to two different levels, and the diffraction patterns were compared. There is no change in unit-cell dimensions during desorption, and there is no sign of changes in the bulk composition of the Al(1)(-)(y)Ti(y) phase during a cycle. Adding pure Ti to a NaH + Al mixture by ball-milling in argon or hydrogen results in formation of TiH(2) that is stable during at least one cycle.     

Adsorption and dissociation of NH3 on clean and hydroxylated TiO2 rutile (110) surfaces: a computational study

The adsorption and dissociation of NH(3) on the clean and hydroxylated TiO(2) rutile (110) surfaces have been investigated by the first-principles calculations. The monodentate adsorbates such as H(3)N-Ti(a), H(2)N-Ti(a), N-Ti(a), H(2)N-O(a), HN-O(a), N-O(a) and H-O(a), as well as the bidentate adsorbate, Ti-N-Ti(a) can be formed on the clean surface. It is found that the hydroxyl group enhances the adsorption of certain adsorbates on the five-fold-coordinated Ti atoms (5c-Ti), namely H(2)N-Ti(a), HN-Ti(a), N-Ti(a) and Ti-N-Ti(a). In addition, the adsorption energy increases as the number of hydroxyl groups increases. On the contrary, the opposite effect is found for those on the two-fold-coordinated O atoms (2c-O). The enhanced adsorption of NH(x) (x = 1-2) on the 5c-Ti is due to the large electronegativity of the OH group, increasing the acidity of the Ti center. This also contributes to diminish the adsorption of NH(x) (x = 1-2) on the two-fold-coordinated O atoms (2c-O) decreasing its basicity. According to potential energy profile, the NH(3) dissociation on the TiO(2) surface is endothermic and the hydroxyl group is found to lower the energetics of H(2)N-Ti(a)+H-O(a) and HN-Ti(a)+2{H-O(a)}, but slightly raise the energetic of Ti-N-Ti(a)+3{H-O(a)} compare to those on the clean surface. However, the dissociation of NH(3) is found to occur on the hydroxylated surface with an overall endothermic by 31.8 kcal/mol and requires a barrier of 37.5 kcal/mol. A comparison of NH(3) on anatase surface has been discussed. The detailed electronic analysis is also carried out to gain insights into the interaction nature between adsorbate and surface.     

Tetrameric,trititanium(IV)-substituted polyoxotungstates with an alpha-Dawson substructure as soluble metal-oxide analogues: molecular structure of the giant "tetrapod" [(alpha-1,2,3-P2W15Ti3O62)4[mu3-Ti(OH)3]4Cl]45-

The preparation and structural characterization of the novel polyoxoanion [(alpha-1,2,3-P(2)W(15)Ti(3)O(62))(4)[mu(3)-Ti(OH)(3)](4)Cl](45-) (1 a; abbreviated to [TiO(6)](16); FW approximately 16 000) which consists of four tri-Ti(IV)-1,2,3-substituted alpha-Dawson substructures, four Ti(OH)(3) bridging groups, and one encapsulated Cl(-) ion, are described. A water-soluble, all-inorganic composition compound of the tetrameric Ti-O-Ti-bridged anhydride form, Na(x)H(45-x)[1 a].y H(2)O (1; x=16-19, y=60-70), which was afforded by the reaction of the tri-lacunary Dawson polyoxotungstate Na(12)[B-alpha-P(2)W(15)O(56)].19 H(2)O with an excess of TiCl(4) in aqueous solution, was obtained as analytically pure, homogeneous colorless crystals. Single-crystal X-ray structure analysis revealed that 1 a was an inorganic, giant "tetrapod"-shaped molecule (inscribed to a sphere with a diameter of approximately 32 A) with approximately T(d) symmetry, in which the 16 edge- and/or corner-shared TiO(6) octahedra were contained. This number of TiO(6) octahedra was larger than that found in other titanium(IV)-substituted polyoxotungstates. Complex 1 was characterized by complete elemental analysis, TG/DTA, FTIR, UV/Vis absorption, and solution ((31)P and (183)W) NMR spectroscopy. The longest wavelength band in the UV/Vis absorption spectra of 1 in water was attributed to the O-->Ti(IV) ligand-to-metal charge-transfer (LMCT) transition: the wavelength of the LMCT band increased linearly as the number of TiO(6) octahedra contained in the Keggin and Dawson polyoxoanions increased. The Ti(n) chromophores formed in the Keggin and Dawson polyoxotungstates are water-soluble analogues of solid TiO(2) or SrTiO(3) as light-semiconductors and photocatalysts.     

不同基材上TiO2膜的表征和光催化活性评价

 采用溶胶-凝胶法在平行条件下制备了负载于钛、铝、不锈钢和玻璃等不同基材上的TiO2浸渍提拉膜,利用原子力显微镜、俄歇电子能谱、X射线衍射、漫反射紫外-可见光谱和苯甲酰胺光催化降解等手段对TiO2膜进行了表征和催化活性评价. 实验结果表明,基材的种类对TiO2膜的性能有较大影响,各膜样品虽均为锐钛矿晶型,但表面形貌显著不同. TiO2/Ti, TiO2/steel, TiO2/Al和TiO2/glass上TiO2的平均粒径分别是152, 205, 241和477 nm,且前两者的粒径分布较为集中. TiO2/Ti和TiO2/Al样品表面仅有Ti和O元素存在,而TiO2/steel和TiO2/glass表面则分别检测到有Fe和Na,Ca及Si等基材元素渗出. 各膜样品对苯甲酰胺光催化降解的活性次序是:TiO2/Ti＞TiO2/Al＞TiO2/glass＞TiO2/steel. 根据实验结果可以推测,在焙烧阶段各基材上前驱体膜烧结行为的不同以及基材元素的渗出是造成不同基材上的TiO2膜在表面形貌、化学组成、光吸收性能以及光催化活性方面存在明显差异的主要原因.     

Li1.3Ti1.7Al0.3(PO4)3与Na+的离子交换

锂离子传导材料Li_1.3Ti_1.7Al_0.3(PO₄)₃是具有NASICON结构的功能材料, 与Na⁺进行离子交换具有选择性高的特性. 研究了在不同温度条件下NaCl和LiCl水溶液中Li_1.3Ti_1.7Al_0.3(PO₄)₃上的Na/Li离子交换行为. 实验结果表明, 升高温度能显著提高Li_1.3Ti_1.7Al_0.3(PO₄)₃的Na/Li交换反应速率, 提高LiCl中杂质Na的分离效果.     

Synchrotron X-ray studies of Al(1-y)Ti(y) formation and re-hydriding inhibition in Ti-enhanced NaAlH4

NaAlH4 samples with Ti additives (TiCl3, TiF3, and Ti(OBu)4) have been investigated by synchrotron X-ray diffraction in order to unveil the nature of Ti. No crystalline Ti-containing phases were observed after ball milling of NaAlH4 with the additives, neither as a solid solution in NaAlH4 nor as secondary phases. However, after cycling, a high-angle shoulder of Al is observed in the same position with 10% TiCl3 as that with 2% Ti(OBu)4, but with considerably higher intensity, indicating that the shoulder is caused by Ti. After prolonged reabsorption, there is only a small fraction of free Al phase left to react with Na3AlH6, whereas the shoulder caused by Al(1-y)Ti(y) is dominating. The Ti-containing phase causing the shoulder therefore contains less Ti than Al3Ti, and the aluminum in this phase is too strongly bound to react with Na3AlH6 to form NaAlH4. The composition of the Al(1-y)Ti(y) phase is estimated from quantitative phase analysis of powder X-ray diffraction data to be Al(0.85)Ti(0.15). Formation of this phase may explain the reduction of capacity beyond the theoretical reduction from the dead weight of the additive and the reaction between the additive and NaAlH4.     

Hydrothermal synthesis and characterization of nanorods of various titanates and titanium dioxide

The formation process of titania based nanorods during hydrothermal synthesis starting from an amorphous TiO2.nH2O gel has been investigated. Sodium tri-titanate (Na2Ti3O7) particles with a rodlike morphology were prepared by a simple hydrothermal process in the presence of a concentrated NaOH aqueous solution. The ion exchange reaction of the synthesized Na2Ti3O7 nanorods with HCl under ultrasonic treatment promotes a complete sodium substitution and the formation of H2Ti3O7 nanorods. Low-temperature annealing of the as-produced nanorods of Na2Ti3O7 and H2Ti3O7 leads to a loss of the layered crystal structure and the formation of nanorods of condensed framework phases-sodium hexa-titanate (Na2Ti6O13) and metastable TiO2-B phases, respectively. These transformations proceed without a significant change in particle morphology. The nanostructures were investigated by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET) method, thermogravimetric analysis (TGA), and Raman spectroscopy. The structural defects of the synthesized nanorods were investigated by high-resolution electron microscopy. The presence of planar defects can be attributed to the exfoliation of the zigzag ribbon layers into two-dimensional titanates as well as to the condensation of the layers of TiO6 octahedra into three-dimensional frameworks.     

Designing the synthesis of catalytically active Ti-β by using various new templates in the presence of fluoride anion

Crystallization of large-pore Ti-β by using a variety of diquaternary ammonium derivatives of dibromoalkane and amines such as triethylamine, 1,4-diazabicyclo[2,2,2]octane (DABCO), and quinuclidine as structure-directing agents (SDA) is described. The size of hydrophobic bridging alkyl-chain length of the template [R(3)N(+)-(CH(2))(x)-N(+)R(3)](OH(-))(2) directs the final crystalline product: Ti-β, Ti-ZSM-12, Ti-nonasil or Ti-ZSM-5, as x gradually changes from 6 to 1, in the fluoride medium under hydrothermal conditions. A dense phase such as Ti-nonasil (clathrasil type) is crystallized as the size of hydrophobic bridging alkyl-chain length decreases. The use of F(-) anions as a mineralizer and Ti(4+) as a heteroatom in the synthesis gel also influences the selectivity of final crystalline product. The phase purity and incorporation of Ti(4+) into the lattice of β (BEA) and ZSM-12 frameworks are confirmed using XRD, UV-visible, FT-IR, (29)Si NMR spectroscopes, elemental analysis (ICP), surface area measurements and catalytic test reactions. The morphology of Ti-β samples is dependent on the nature of the structure-directing agent as revealed by the scanning electron microscopic (SEM) observations. The catalytic activity in the epoxidation of 4-vinyl-1-cyclohexene is increased with the amount of tetrahedral Ti(4+) atoms in the framework. The new templates can be effectively used for preparation of catalytically active Ti-β with the minimum number of framework defect sites.     

Sandia octahedral molecular sieves (SOMS): structural and property effects of charge-balancing the M(IV)-substituted (M = Ti, Zr) Niobate framework

Sandia octahedral molecular sieves (SOMS) is an isostructural, variable composition class of ion exchangers with the general formula Na(2)Nb(2-x)M(IV)(x)O (6-x)(OH)(x).H(2)O (M(IV) = Ti, Zr; x = 0.04-0.40) where up to 20% of the framework Nb(V) can be substituted with Ti(IV) or Zr(IV). This class of molecular sieves is easily converted to perovskite through low-temperature heat treatment (500-600 degrees C). This report provides a detailed account of how the charge imbalance of this Nb(V)-M(IV) substitution is compensated. X-ray powder diffraction with Rietveld refinement, infrared spectroscopy, thermogravimetric analysis, (23)Na MAS NMR, and (1)H MAS NMR were used to determine how the framework anionic charge is cation-balanced over a range of framework compositions. All spectroscopic evidence indicated a proton addition for each M(IV) substitution. Evidences for variable proton content included (1) increasing OH observed by (1)H MAS NMR with increasing M(IV) substitution, (2) increased infrared band broadening indicating increased H-bonding with increasing M(IV) substitution, (3) increased TGA weight loss (due to increased OH content) with increasing M(IV) substitution, (4) no variance in population on the sodium sites (indicated by Rietveld refinement) with variable composition, and (5) no change in the (23)Na MAS NMR spectra with variable composition. Also observed by infrared spectroscopy and (23)Na MAS NMR was increased disorder on the Nb(V)/M(IV) framework sites with increasing M(IV) substitution, evidenced by broadening of these spectral features. These spectroscopic studies, along with ion exchange experiments, also revealed the effect of the Nb(V)/M(IV) framework substitution on materials properties. Namely, the temperature of conversion to NaNb(1-x)M(IV)(x)O(3) (M = Ti, Zr) perovskite increased with increasing Ti in the framework and decreased with increasing Zr in the framework. This suggested that Ti stabilizes the SOMS framework and Zr destabilizes the SOMS framework. Finally, comparing ion exchange properties of a SOMS material with minimal (2%) Ti to a SOMS material with maximum (20%) Ti revealed the divalent cation selectivity of these materials which was reported previously is a function of the M(IV) substitution in the framework. A thorough investigation of this class of SOMS materials has revealed the importance of understanding the influence of heterovalent substitutions in microporous frameworks on material properties.     

Microwave synthesis,characterization and catalytic properties of titanium-incorporated ZSM-5 zeolite

Titanium-incorporated ZSM-5 zeolites (Si/Al = 50–200 and Si/Ti = 70) were successfully synthesized in a one-step sol-gel process under microwave irradiation. The characteristics of Ti-ZSM-5 zeolites were investigated using X-ray power diffraction, UV/Vis-DRS, FT-IR spectroscopy and solid-state ²⁷Al-NMR to monitor the physico-chemical properties. Simultaneously, the acidic properties were characterized by the NH₃-TPD profile. The characterization results revealed that the Ti⁴⁺ and Al³⁺ ions were well incorporated into the framework of Ti-ZSM-5 zeolite. The prepared zeolite was moderately active but selective in the dehydration of methanol to dimethyl ether.     

Syntheses and structural characterization of a series of one-dimensional fluorotitanophosphates (NH4)(x)K(4-x)[Ti(2)PO(4)F(9)] (x = 0, 0.70, 1.00, 1.25)

A series of novel fluorotitanophosphates with a general formula (NH4)xK4 - x[Ti2PO4F9] (x = 0, 0.70, 1.00, 1.25, named as 1, 2, 3, and 4 respectively) have been synthesized under hydrothermal conditions. Their structures were determined by X-ray single-crystal diffraction technique, which show that all of the phases in this series contain an idental anionic fluorotitanophosphate chain, consisting of alternating linkage of PO4 tetrahedra and TiO2F4 octahedra. The fluorotitanophosphate chain is unique, which is different from the first titanophosphate chain found in [Ti3P6O27].5[NH3CH2-CH2NH3].2H3O. Another interesting observation of this series is that, by partial substitution of potassium by ammonium, the structure converts to a more-symmetric version, while maintaining all of the topological feature.     

Ti-ZSM-11的红外光谱研究

随着杂原子分子筛研究领域的开拓与发展，近年来，对钛硅沸石的研究逐渐增多．Ti－ZSM－11（TS－2）型分子筛是由Reddy，Ratanasarny等[1]首先合成的．钛硅沸石的表征与其它杂原子分子筛相比较为复杂，对杂原子Ti是否进入了骨架还没有一个直接的证据，且争议较多．在红外光谱的研究中，对960cm－1－980cm－1区间的特征吸收的归属也存在着很大的分歧[2－4]．钛硅沸石在H2O2对有机化合物的选择氧化领域有极其优良的催化性能[1]，因此，对它的开发有广泛的应用前景．本文以动态和静态相结合的水热晶化法合成了Ti－ZSM－11型分子筛．IR光…     

XANES and XPS investigations of the local structure and final-state effects in amorphous metal silicates: (ZrO2)(x)(TiO2)(y)(SiO2)(1-x-y)

Amorphous quaternary [(ZrO(2))(x)(TiO(2))(y)(SiO(2))(1-x-y)] and ternary [(ZrO(2))(x)(SiO(2))(1-x)] silicates were synthesized using a sol-gel method and examined via XPS and XANES. Metal silicates are important industrial materials, though structural characterization is complicated because of their amorphous nature. Hard (Ti K- and Zr K-edge) and soft (Ti L(2,3)-edge) X-ray XANES spectra suggest the Ti and Zr coordination numbers in the quaternary silicates remain constant as the metal identity or total metal content (x, y, or x + y in the chemical formula) is varied. XPS core-line spectra from the quaternary silicates show large decreases in Ti 2p(3/2), Zr 3d(5/2), Si 2p(3/2), and O 1s binding energies due to increasing final-state relaxation with greater next-nearest neighbour substitution of Si for less-electronegative Ti/Zr, which was confirmed by analysis of the O Auger parameter. These decreases in binding energy occur without any changes in the ground-state energies (e.g., oxidation state) of these atoms, as examined by Ti L(2,3)-edge, Si L(2,3)-edge, and O K-edge XANES. Because most spectroscopic investigations are concerned with ground-state properties, knowledge of the contributions from final-state effects is important to understand the spectra from materials of interest.     

First principles studies of vanadia-titania monolayer catalysts: mechanisms of NO selective reduction

The selective reduction of NO with NH(3) catalyzed by isolated VO(x) species grafted onto TiO(2) (anatase) is studied by means of periodic density functional calculations. NH(3) is adsorbed molecularly by the bare support both as a Lewis-bonded complex at (101) 5-fold coordinated Ti sites, and as a H-bonded complex at (001) Ti-OH sites. Analogous interactions are predicted for stable submonolayer VO(x) species, which provide V(5+) Lewis acid sites and V-OH sites. Neither Ti-OH nor submonolayer V-OH groups act as Br?nsted acids toward NH(3). Reaction pathways where both Lewis-bonded and H-bonded NH(3) complexes yield a NH(2)NO intermediate are found. In the former case, a (rate-determining) deprotonation step of NH(3) is required, whereas, in the latter, NH(2)NO is formed directly through a concerted mechanism. This suggests that many channels may contribute to the NO reduction process.