The vulcanization of rubber with unsaturated salts: A preliminary small-angle x-ray scattering investigation

Small angle X-ray scattering diagrams in the range 6′-60′ of 2 β have been obtained for vulcanizates of styrene-butadiene, acrylonitrile-butadiene and polybutadiene 1,4-cis rubbers with different amounts of salts of methacrylic acid or complex sats of 2-vinylpyridine as vulcanizing agents. A marked diffuse scattering was found in the range 6′-40′ of 2 β. By means of scattering diagrams of swollen specimens and of specimens in which salt links were destroyed, the scattering was explained as due to the “clusters”, rigid particles of vulcanization agents, polymerized and grafted to the rubbers. Effective diameters and approximate shape of the clusters were determined for PB rubbers vulcanized with 20% Mg methacrylate.     

Raman spectroscopy and thermal analysis of gum and silica-filled NR/SBR blends prepared from latex system

Natural rubber/styrene-butadiene rubber (NR/SBR) blends, with and without silica, were prepared by co-coagulating the mixture of rubber latices and various amounts of well-dispersed silica suspension. An attempt to predict blend compositions was made using Raman spectroscopy in association with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was found that the intensity of each Raman characteristic peak was strongly dependent on the blend composition, but there was no significant evolution with the presence of silica. Also, TGA results revealed an improvement in thermal stability of NR/SBR blends with increasing both SBR and silica contents due to the dilution effect. Two distinct glass transition temperatures (T_g) were observed in DSC thermograms of all blends, and their T_g values were independent on both blend composition and silica content. This indicated a physical blend formation, which agreed well with no shifts in Raman peaks of the blends in comparison with those of the individual rubbers. Linear regression with R² quality factor close to 0.99 was achieved when plotting intensity ratio at 1371/1302 cm^?1 versus blend ratios. On the other hand, the peak height ratio and heat capacity ratio from TGA and DSC analysis, respectively, yielded quadratic equations as a function of blend ratios.     

Synthesis of ferrocenyl-containing silicone rubbers via platinum-catalyzed Si–H self-cross-linking

Self-cross-linkable ferrocenyl-containing polymethylhydrosiloxanes were synthesized. Karstedt's catalyst and cis-[PtCl₂(BnCN)₂] were examined as cross-linking catalysts at room temperature for the reaction between Si–H groups of the ferrocenyl-containing polymethylhydrosiloxanes. Cis-[PtCl₂(BnCN)₂] is an effective catalyst that allows cross-linked ferrocenyl-containing silicones (silicone rubbers) to be obtained with no visible mechanical defects (bubbles or cracks) compared with Karstedt's catalyst. The ferrocene content of the ferrocenyl-containing silicone rubbers was found to be approximately 50 wt.% by energy-dispersive X-ray analysis. Compared with cross-linked non-modified polymethylhydrosiloxanes, the ferrocenyl-containing silicone rubbers exhibited improved tensile properties (the tensile strength increased from 0.47 to 0.75 MPa) and a 1.5–2.5 times lower cross-linking degree. The surface resistivity of the ferrocenyl-containing silicone rubbers (50 wt.% ferrocenyl units) was approximately 7 × 10⁹ Ω/□, which was 10,000 times lower than that of pure polymethylhydrosiloxane. The obtained flexible electroactive ferrocenyl-containing silicone rubbers can potentially be applied as coatings for electronic and electrostatic-sensitive devices, interfaces, and sensors.     

Radiation effects on polymers—IV: Straight radiation vulcanization of styrene-butadiene rubber mixes

Vulcanization of styrene-butadiene rubbers was carried out by gamma radiation in air. For unloaded unextracted rubbers, the dose required for optimum cross-linking was about 40 megaroentgens (MR). Elimination of foreign materials and stabilizers and also incorporation of filler affected the vulcanization. Loaded samples gave vulcanizates with best complex physico-mechanical properties for filler content of 50 (phr) and a dose of 30 MR. Evaluation of various fillers has shown that the best properties were obtained with HAF among the black fillers and silica in the case of white fillers.     

SPECTRAL ANALYSES OF LOW LEVEL CHEMILUMINESCENCE OF A SHORT LIFETIME USING A HIGHLY SENSITIVE POLYCHROMATIC SPECTROMETER INCORPORATING A TWO DIMENSIONAL PHOTON-COUNTING TYPE DETECTOR

Abstract— Spectral analyses of low level chemiluminescence were carried out by using a newly developed polychromatic spectrometer in which a diffracted photon emission was detected simultaneously using a two dimensional photon-counting device. The spectrometer was sensitive in the 400–800 nm wavelength range. Low level chemiluminescence generated in a 1 nM luminol solution could be detected as a spectrum, showing a peak at 430 nm. Short lifetime photon emission from singlet oxygen showed only two peaks at around 630 and 700 nm in this highly time-resolved spectroscopy. Lipid peroxidation of linoleic acid by the lipoxygenase emitted a low intensity peak centered at 440 nm, but singlet oxygen emission arising from the decomposition of lipid peroxide was not observed. An injured cotyledon of a soybean seedling gave a broad emission centered at 725 nm in the absence of hydrogen peroxide, while in its presence a different emission peak appeared at a shorter wavelength (515 nm). Oxygenated, fluorescent components in the soybean seedling may be the emitting species. Singlet oxygen and triplet carbonyl groups were shown to be unlikely sources of the emission.     

溶聚丁苯链化学结构的NMR研究

溶聚丁苯链化学结构的NMR研究;溶聚丁苯; 链化学结构; 相容性     

Fire performances of unvulcanized rubbers and influences of horizontal flowing melts

Fire performances of typical unvulcanized rubbers are investigated and the properties of rubbers and their flowing melts are characterized. If the horizontal melt flow is allowed the burning area increases by 75%–473% and proportionally the peak mass loss rate promotes by 55%–300%. When the rubber converts to its flowing melt the viscosity and heat of complete combustion reduce, and the total crosslink density increases, which might be ascribed to the curing, the curing reversion and the decomposition mechanism. Except for acrylonitrile-butadiene rubber both the T_d,5% and the decomposition activation energy decrease. The pool fire development is related with the melt viscosity, the decomposition temperature and heat release rate (HRR) in the cone calorimeter. Low viscosity contributes to large pool area. High HRR and low decomposition temperature accelerate the extension of burning area.     

Chemiluminescence upon Photooxidation of 4,4"-Diazidodiphenyl with Molecular Oxygen

It was found that irradiation of the solution of 4,4"-diazidodiphenyl in ethyl alcohol with UV-light at a wavelength longer than 280 nm in the presence of dissolved oxygen resulted in appearance of post-luminescence. The luminescence intensity increases with increasing the oxygen concentration; the luminescence virtually disappears after purging the solution with argon. The observed emission of light was attributed to chemiluminescence of the products of photooxidation of 4,4"-diazidodiphenyl. The rate dependence of the afterglow shows two maxima. The first is observed immediately after cessation of the UV irradiation of the solution and its transfer to a photometric cell. The intensity of the corresponding chemiluminescence decreases by an exponential law with _e= 5 s. The second maximum appears after a certain time interval after the first one. Addition of a triplet sensitizer (Michler's ketone) to the reaction mixture results in quenching of the chemiluminescence from the photooxidation products, whereas the addition of substances that stabilize electrophilic species in the singlet state leads to an increase in the chemiluminescence intensity. It was suggested that the chemiluminescence resulted from reactions involving the singlet nitrene adduct with oxygen.     

Dielectrical and electro-mechanical behavior of NBR at high electric field strength

The aim of this work is to present a new approach to characterize the dielectric properties of elastomers especially at low frequencies and high electric field strength, close to the operating conditions of dielectric elastomer actuators (DEA). By means of an electro-rheological measuring cell, static (DC) and alternating (AC) high electric field strength were applied to different types of acrylonitrile-butadiene rubbers (NBR), with varying content of polar acrylonitrile groups. Based on fundamental theory of electricity complex permittivity and polarization were calculated from Coulomb stress measurements at varying frequencies. During high voltage measurements it was observed, that dielectric loss current increases, if a certain critical field strength is exceeded. It is shown, that polar NBR rubbers exhibit a critical field strength far below of the non-polar polybutadiene rubber (BR), acting as a reference sample. NBR exhibits extraordinary high permittivity at low frequency, which makes this material as a favorite candidate for DEA. Furthermore, mechanical properties of NBR can be easily altered by application of an alternating electric field. This phenomenon opens new opportunities in a great variety of applications.     

Structural and Photoluminescence Behaviors of Nano-Structure Thin Film and Bulk Silica Gel Derived Glasses

Nano-structure bulk and thin film silica gel derived glasses were prepared by sol-gel technique. Both samples were derived from the same precursor and subjected to the same heat-treatment regime. Structural information about prepared samples are obtained by analyzing the XRD patterns and TEM micrographs. The bulk samples phase changes from amorphous to -crystoballite at higher temperature (1300°C) than that in the thin film (500°C). The crystallite size depends to a large extent on the heat-treatment temperature. Bulk sample heat treated at 1400°C was as small as 10.4 nm. Thin film samples show higher response to heat-treatment temperature than the bulk samples, where the film is denser, has smaller pores and seems more homogeneous at lower temperature than bulk sample as revealed by SEM. The observed Raman spectra for bulk and thin film samples are in accordance with that of the -crystoballite. The Raman peak intensity is higher for thin film than bulk samples. The photoluminescence PL measurements for bulk samples show a broad intense peak at 532 nm combined with three weak peaks at longer wavelength 587, 635 and 666 nm. The PL peak intensity shows a reasonable decrease with increasing the heat-treatment temperature while the peak position shifted slightly to a lower wavelength. While the thin film samples show a unique peak at wavelength = 523 nm. The appearance of PL bands are interpreted on the light of non-bridged oxygen hole center as well as the structure defects.     

LONG WAVELENGTH UV RADIATION AFFECTS CHEMILUMINESCENCE OF HUMAN POLYMORPHONUCLEAR LEUCOCYTES

Abstract— Luminol-enhanced chemiluminescence in suspensions of human polymorphonuclear leucocytes stimulated with the chemotactic oligopeptide formyl-methionyl-leucyl-phenylalanine was increased by exposure of the cells to long wavelength UV radiation (mainly320–400 nm). Leucocytes treated with 0.3 × 10⁴ J m^-2 of UV responded with doubled peak values, and 4 × 10⁴ J m^-2 lead to a five-fold increase in peak chemiluminescence, as compared with non-exposed cells. Supernatants isolated from irradiated leucocytes contained increased amounts of both myeloperoxidase and lactate dehydrogenase and showed higher chemiluminescence values, when compared with supernatants from sham-irradiated cells. The results suggest that leucocyte degranulation contributes to the inflammatory properties of long wavelength UV.     

Investigations of the Enhancer Effect of a High-Salt Concentration Medium on the Luminol Chemiluminescent Reaction

The enhancer effect of a high-salt concentration medium on the luminol chemiluminescence reaction catalyzed by either soluble or immobilized peroxidase has been investigated. Some widely used salts were tested at high concentration (up to 3 mol L): potassium chloride, sodium chloride, ammonium sulfate and calcium chloride. The magnitude of the light intensity enhancement depends on the nature of the salt and on the form of the peroxidase, i.e. free in solution or immobilized. The enhancement is observed whether the catalyst of the chemiluminescence reaction is peroxidase or ferricyanide. Both the enhanced or nonenhanced luminol chemiluminescence spectra have a maximum wavelength emission at around 425 nm. The results reported in this study are in favor of an action of the salts on the nonenzymatic steps of the luminol chemiluminescence reaction rather than a modification of the enzymatic process.     

Thermodynamic characterization of carbon black-filled rubbers

Unfilled and carbon black-filled samples of synthetic isoprene- and butadiene-methylstyrenebased rubbers were characterized by precise heat capacity measurements in the temperature interval 4.2–300 K. Both unfilled samples proved to behave in an essentially fracton-like way in the temperature interval 6–30 K. The excess thermodynamic quantities derived from the smoothed data suggested that the thermodynamic state of the elastomeric phase in the filled rubbers was intrinsically unstable.     

Effect oftrans-polyoctenamer on thermal stability of rubbers determined by thermal analysis

An effect of a cyclic low molecular-weight polymertrans-polyoctenamer rubber (TOR) on the thermal stability of diene rubbers and their vulcanizates was investigated. The investigation was carried out in the air and nitrogen atmospheres using thermogravimetry, DSC and simultaneous thermoanalytical methods. The thermal stability indexes:T ₅,T _max and activation energy of degradation (E), as well asT _g andT _m values, have been determined.It was found thattrans-polyoctenamer (TOR) increases of the thermal stability indices of raw diene rubbers and their vulcanizates. The results show that the thermal degradation of diene rubbers occurred at higher temperature if they were blended with TOR. In our opinion, intermolecular structures formed between the cyclic low-molecular weight polymer and some linear rubber molecules may be the reason for the higher thermal stability of these rubber blends.The work was supported by State Committee for Research, Poland. Grant No. 7.T08 E 032-08.     

Electrochemistry, electrogenerated chemiluminescence, and excimer formation dynamics of intramolecular π-stacked 9-naphthylanthracene derivatives and organic nanoparticles

We report the electrochemical characterization and the observation of excimer emission from a series of 9-naphthylanthracene-based dimer- and trimer-bridged high steric hindrance aromatic groups during photoluminescence (PL) measurements in the solid state and in solution electrogenerated chemiluminescence (ECL) measurements. Cyclic voltammetry of 4,4'-bis(9-(1-naphthyl)anthracen-10-yl)biphenyl (4A) and 1,3,5-tris(9-(1-naphthyl)anthracen-10-yl)benzene (4C) showed two or three reversible, closely spaced one-electron transfers on oxidation in dichloromethane. The ECL emission spectra of 4A and 4C resulting from the annihilation reaction in benzonitrile showed two bands: one at the same wavelength as the PL peak in the solution state, and a broad band at longer wavelength. With a coreactant, such as peroxydisulfate, ECL spectra showed a single peak that was less broad in shape. PL measurement in the solid state and measurement of representative time traces of PL intensity, lifetimes, and picosecond time-correlated single-photon counting confirmed excimer emission at long wavelength. A reprecipitation method was used to prepare well-dispersed organic nanoparticles (NPs) of 4A in both aqueous and acetonitrile solutions. The smallest stable size of NPs produced was ~15 ± 6 nm, as analyzed by transmission electron microscopy. These organic NPs produced stable and weak ECL emission from the annihilation reaction in both aqueous and MeCN solutions. With a coreactant, such as peroxydisulfate, the ECL signal on reduction was sufficiently strong to obtain an ECL spectrum.     

Thermal oxidative degradation of additive-free polypropylene pellets investigated by multichannel Fourier-transform chemiluminescence spectroscopy

Thermal oxidative degradation of additive-free polypropylene pellets heated isothermally in dry air at 150 and 180 °C (below and above the melting point of 163 °C) was investigated by multichannel Fourier-transform chemiluminescence spectroscopy. The initial peak wavelength of chemiluminescence emission at 490 nm remained constant during the early stages of thermal degradation, but new emissions developed with time in the red spectral region over an extended oxidation period. The time-dependent luminescence spectra were deconvoluted into three emission bands by least-squares fitting using Gaussian curves. We concluded that at least three groups of luminescent species (luminophores), having different conjugation lengths, were generated by thermal oxidation over extended periods and show luminescence around 490, 660, and 740 nm.     

Oxidation of ultra high molecular weight polyethylene (UHMWPE) part 1: Interpretation of the chemiluminescence curve recorded during thermal oxidation

The chemiluminescence curve of polyethylene differs from that of polypropylene even though the oxidation behaviour is similar. The CL curve of PE normally exhibits a double sigmoidal behaviour, whereas PP shows a single sigmoid, and its luminescence intensity is also much lower. It was found, by investigating the build-up of carbonyls and hydroperoxides by means of FTIR, that the first peak coincides with a maximum in hydroperoxide concentration and the second with the build-up of carbonyls. The intensity of the first peak is enhanced by doping the PE with DPA (9,10-diphenylanthracene), which is a chemiluminescence activator, but unaffected by doping the PE with DBA (9,10-dibromoanthracene), which is an energy acceptor. The intensity of the first peak also depends on the presence of carbonyls in the sample. From these observations it is concluded that the CL from PE is a type of activated chemiluminescence, which originates from hydroperoxide decomposition, with carbonyls acting as activator.     

溶胶-凝胶法制备掺Sm3+的SiO2玻璃的结构及发光性能

利用溶胶-凝胶技术制备了掺不同量Sm3+和不同退火温度下的SiO2凝胶和玻璃,通过三维荧光光谱、激发光谱、发射光谱的测试,确定了Sm3+在SiO2凝胶玻璃中的最佳激发波长为360 nm,最强发射波长为610 nm,激发光谱的峰位置在360、393、464 nm处,发射光谱的峰位置在578、591、595、610、732nm处,分别归属于4G5/2-6H5/2、4G5/2-6H7/2、4G5/2-6H11/2跃迁,并证明当掺杂量达到1.15%时,Sm3+的发光最强,当Sm3+的掺杂量超过1.15%时,发生浓度猝灭效应.     

Thermal behavior of partially hydrogenated polydienes by <Emphasis Type="Italic">p</Emphasis>-toluenesulfonylhydrazide

The hydrogenation of natural rubber (NR), polybutadiene (BR), and styrene-butadiene (SBR) rubbers with different microstructures was performed by a diimide hydrogenation agent generated in situ by a non-catalytic method [1–3]. Many properties of the material depend considerably on variables such as degree of hydrogenation and proportions of vinyl or phenyl units. The mobility of the hydrogenated chain was investigated by differential scanning calorimetry (DSC) and the results confirm the relationship between the degree of hydrogenation and chain flexibility. The flexibility of a high cis-1,4 BR hydrogenated sample, was significantly changed and a melting point (T _m) was detected after a certain degree of hydrogenation. Thermal stability was investigated by thermogravimetric analysis (TG) and an increase was found, but, the thermal resistance was influenced by the presence of the byproduct p-toluenesulfinic acid. Oxidation stability was investigated by chemiluminescence analysis and it improved with hydrogenation.     

密封橡胶材料的压力-体积-温度关系的研究

制备了3种密封胶材料——丁苯橡胶、丁腈橡胶及丁腈/氯化丁基混合橡胶材料,利用压力-体积-温度(P-V-T)高压膨胀计对样品进行测试,得到了比容Vsp随着温度T和压力P变化的关系;采用Tait方程研究了P-V-T性能,并计算出Tait方程中相应的参数.结果表明,Tait方程计算所得的P-V-T理论关系与实验结果一致,具有较好的规律性;b3、b4均为常数,即B为常数;Tait方程计算所得值与实验值的平均残差均小于0.02,吻合度较好;因此Tait方程可以较好地描述3种密封橡胶体系的P-V-T关系,并且为定量研究密封橡胶材料的P-V-T关系提供理论基础.同时,根据Tait方程所得的参数,计算了3种橡胶材料的热膨胀系数α和等温压缩系数β,研究了3种橡胶材料的α和β随着压力、温度的变化规律,结果表明3种材料中丁苯橡胶的尺寸稳定性最好,而丁腈/氯化丁基复合橡胶的尺寸稳定性较差并且其α随着压力的变化有较大的改变.准确地描述了3种密封橡胶材料的α和β随压力、温度的变化.