μs级充电时水介质同轴电容击穿实验研究

 研制了水介质同轴电容的实验装置，在此装置上进行了大量的实验。测得μs级充电时，水介质同轴电容分别在正脉冲和负脉冲充电时的击穿电压，负击穿电压的理论值与测量值相差较大，正击穿电压的理论值大于测量值的18%左右，对此实验结果进行了分析。此外，当去离子水的电阻率从13MΩ·cm降到5 MΩ·cm时，水介质同轴电容器的击穿电压基本不变。     

Dielectric surface flashover in a simulated low Earth orbitenvironment

Surface flashover on insulators under UV irradiation or with a plasma background was investigated with high-speed electrical and optical sensors in order to clarify differences in the breakdown development compared to the pure vacuum case. Results with a plasma background show a more rapid development in the breakdown initiation compared to measurements in vacuum with no plasma. With a magnetic shielding technique using permanent magnets, the duration of an applied voltage pulse can be increased by a factor of 2-3 without causing flashover. UV illumination on the electrodes decreases the flashover voltage (for the dc case) or the voltage pulse duration without breakdown (for the pulsed case), whereas UV illumination on the dielectric surface increases the flashover potential     

固态高压脉冲形成线研究

 为了实现高压脉冲形成线小型化,开展了平板固态脉冲形成线研究。实验研究了两种作为储能介质的固态材料的高压体击穿特性、沿面闪络特性和频率响应特性,一种是特种复合材料,其相对介电常数在50～250之间,另一种是功能陶瓷,其相对介电常数在200～1 000之间。在此基础上,研制了两种平板固态脉冲形成线。特种复合介质固态脉冲形成线试验电压为3 kV左右,输出电压脉冲半高全宽（FWHM）可以达到58 ns;功能陶瓷介质固态脉冲形成线的试验充电电压超过120 kV,输出电压脉冲半高全宽为92 ns。     

脉冲形成线用CaO-TiO2-Al2O3基介质陶瓷介电性能

设计了一种脉冲形成线用新型CaO-TiO2-Al2O3基介质陶瓷体系,采用传统固相法通过优化组分和制备工艺,调控材料的微结构,获得了介电性能优异的介质陶瓷。其介电常数在15~35之间可调,介电损耗小于0.002,频率稳定性好。在厚度为1 mm时,介电强度高达50 kV/mm。研究了厚度对CaO-TiO2-Al2O3基介质陶瓷介电强度的影响规律,当厚度从1 mm减小到0.1 mm时,介电强度呈非线性增大,从50 kV/mm（1 mm厚样品）提高到92 kV/mm（0.1 mm厚样品）,可见,CaO-TiO2-Al2O3基介质陶瓷的电击穿与其机械损坏具有相似性。结合CaO-TiO2-Al2O3基介质陶瓷的化学组分和微观结构,CaO-TiO2-Al2O3基介质陶瓷优越的电击穿特性可以用弱点击穿理论解释。     

微秒脉冲激励的大气压氦等离子体射流放电特性北大核心CSCD

研究了不同电极结构以及放电参数对微秒脉冲激励的氦等离子体射流放电特性的影响。实验中采用不同管内径、不同电极形状、不同重复频率等参数,通过采集放电阶段的电流电压图、发光图像以及发射光谱等,对等离子体射流的电学特性和光学特性进行诊断。实验结果表明,随着管内直径的增大,氦等离子体射流的长度减小;管内径为8mm时,等离子体射流的击穿电压与放电电流最小,同时,其发射光谱中第二正带系N2,N+2和O等高能活性粒子的强度最高;管内径为5mm的等离子体射流的放电电流、功率及消耗的能量最大;在相同实验条件下,针尖电极结构中的放电电流、消耗的功率还有发射光谱强度都较大;随着重复频率的增加,氦等离子体射流的长度会增加,但击穿电压减小。     

Creepage discharge along the surface of solid dielectrics in water

Experimental data is given for the discharge voltage for creepage discharge in tap water as a function of the thickness, flange length, (creepage path over dielectric surface), permittivity of the solid dielectric, field configuration, polarity of the applied voltage pulse, and a number of other parameters. The experimental data discussed are the delay time with dielectric flange sparkover by creepage discharge, the average discharge propagation rate for both polarities, and the creepage discharge current and leakage resistance.     

一种紧凑型高功率脉冲调制器

 研制了一种基于水介质单同轴脉冲形成线型的高功率脉冲调制器,该调制器由初级储能电容器、脉冲变压器、水介质同轴脉冲形成线、氢气主开关和场发射真空二极管等组成。用Pspice电路软件对脉冲形成线的充电电压和二极管电压、电流进行了模拟,并用有限元软件分析了脉冲形成线的电场分布。当初级储能电容器组充电电压为35 kV, 氢气主开关导通电压高达520 kV时,在调制器场发射二极管输出电压约230 kV, 束流30 kA,脉宽约60 ns的高电压脉冲。此外,对主开关充不同类型的气体进行了实验研究,结果表明:氢气主开关的脉冲调制器能够在二极管上获得前沿更陡的高电压脉冲,并能有效地改善二极管电子束的性能。理论分析与实验结果基本一致。此种类型的调制器具有运行稳定、体积小、结构紧凑的特点。     

玻璃-陶瓷脉冲形成线的充放电特性

采用熔融-快冷-可控结晶工艺，制备了(Pb，Sr)Nb₂O₆-NaNbO₃-SiO₂大尺寸玻璃陶瓷，开展了其介电性能以及脉冲充放电特性研究。实验结果表明:该玻璃陶瓷材料的介电常数约为340，具有良好的温度稳定性和正的偏压特性。基于该材料制备的固态脉冲形成线输出脉冲脉宽约为89 ns，具有良好的脉冲平顶和窄的上升沿。在19 kV充放电电压、1 kHz的充放电频率、4 kA的放电电流条件下，固态脉冲形成线充放电寿命大于100万次。     

Investigation of Discharge Channel Elongation under Thermal Dielectric Breakdown

A mathematical model of the expansion of a discharge channel due to a growing electrothermal instability in a solid dielectric material under constant voltage is considered. The model describes temperature dynamics, electric field strength, discharge density, and melting of the dielectric. The paper reports the results of a numerical investigation of the discharge-channel expansion during the breakdown of ceramic BeO in a point-to-plane electrode configuration.     

Low Voltage Firing Characteristics of a Simple Triggered Vacuum Gap

The firing characteristics of the simple triggered vacuum gap (TVG) using lead zirconate titanate as dielectric material in the triggered gap are described. This TVG has a long life of about 2000 firings without appreciable deterioration of the electrical properties for main discharge currents upto 3 kA and is much superior to these made with Supramica (Mycalex Corporation of America) and silicon carbide as used in our earlier investigations. The effects of the variation of trigger voltage, trigger curcit, trigger pulse duration, trigger pulse energy, main gap voltage, main gap separation and main circuit energy on the firing characteristics have been studied. Trigger resistance progressively decreases with the number of firings of the trigger gap and as well as of the main gap. This decrease in the trigger resistance is more pronounced for main discharge currents exceeding 10 kA. The minimum trigger current required for reliable firing decreases with increase of trigger voltage upto a threshold value of 1.2 kV and there-onwards saturates at 3.0 A. This value is less than that obtained with Supramica as dielectric material. One hundred percent firing probability of the TVG at main gap voltages as low as 50 V is possible and this low voltage breakdown of the main gap appears to be similar to the breakdown at low pressures between moving plasma by other workers. and the cold electrodes immersed in it, as reported     

200kV水介质高压脉冲延时线

介绍了200 kV水介质高压脉冲延时线的基本设计参数,阻抗为23.4Ω,电长度为300 ns;分析了该延时线的耐压特性,并对其传输脉冲幅度衰减率进行了估算。加工了一套高压脉冲延时线装置,并进行了实验研究。实验中,利用Blumlein线产生两路高压方波脉冲输出,一路经高压电缆-延时线-高压电缆到匹配负载,另一路经过高压电缆到匹配负载,两负载上的脉冲等效认为是延时线的输出脉冲和输入脉冲。实验结果表明,该延时线工作电压大于200 kV,输入方波脉冲前沿为30 ns,输出方波脉冲前沿增加到34.5 ns,方波脉冲幅度损耗率为1.8%。     

大气压介质阻挡辉光放电中放电电流的测量与分析

介质阻挡放电产生的低温等离子体具有广泛的应用前景而成为研究热点。文章利用平行平板介质阻挡放电装置,在流动的氦气中实现了大气压均匀辉光放电,得到了大气压下的均匀等离子体。利用电学方法将放电电流从总电流中分离出来,从而得到了辉光放电的放电电流。通过分析放电电流、外加电压、气隙上电压以及壁电荷电量之间的相互关系,可以研究气体放电过程中壁电荷积累的微观动力学行为。实验结果表明壁电荷主要是在放电电流脉冲持续期间积累的,但电流脉冲结束后,由于气隙电压没有改变极性,壁电荷还会逐渐积累,气隙电压改变极性后,壁电荷量随时间减小。这些结果对壁电荷在介质阻挡辉光放电中作用的深入研究和大气压介质阻挡辉光放电的工业应用具有重要意义。     

介质壁加速器用固态脉冲形成线设计与实验

设计和研制了一种CaO-TiO2-Al2O3复合陶瓷平板固态脉冲形成线,以期用于介质壁加速器。该脉冲形成线的几何参数为:陶瓷介质长度300mm,宽度15mm,厚度1mm;银电极长度280mm,宽度2mm。电性能参数为:相对介电常数约23.5,特征阻抗约26Ω,电长度约4.5ns,直流耐压场强大于20kV/mm,在μs量级上升时间的脉冲电压下绝缘强度大于25kV/mm。该固态脉冲形成线设计兼顾了光导开关的使用要求、高梯度绝缘子的设计指标、带电粒子束的输运及加速器的结构设计要求。结合GaAs光导开关,开展了固态Blumlein脉冲形成线实验研究工作,在脉冲充电电压约25kV的条件下,固态Blumlein脉冲形成线实现脉冲电压输出约23kV。     

Effect of the duration of the front edge of the voltage pulse on the electric breakdown of ammonium perchlorate

The results of a study of the effect of the front edge duration of a voltage pulse (τ) on the electric breakdown of ammonium perchlorate single crystals are submitted. Experiments have shown that at τ<1.5 µs, the breakdown threshold field increases with reduction in τ and does not depend on τ at τ>1.5 µs. It is shown that the electric breakdown of ammonium perchlorate results from an impact generation of electrons. The impact generation rate of electrons versus electric field and the diameter of the through channel being formed during electric breakdown in ammonium perchlorate are estimated.     

Entwicklung leistungsfähiger Stickstofflaser mit abgeschmolzenem Laserrohr

For an increase of the laser pulse energy from longitudinally excited multiple electrodes tubes, experiments and model calculations have been accomplished. A variation of the electrode spacing in the laser tube has shown, that a maximum pulse energy could be achieved with about 40 mm electrode spacing. If barium titanat capacitors with a dielectric constant of 10000 in the pulse forming unit were applied, a voltage pulse transform occured enabling an increase of the laser power up to 50%. With a sealed off operated laser tube of 100 cm active length, a laser peak power of 600 kW and a pulse duration of 10 ns could be achieved. A tube with 200 cm active length generated a pulse power of 1.2 MW. The decrease of laser pulse energy with increasing pulse repetition rate can be explained by the decrease of impulse breakdown voltage. For an increase of the lifetime of laser tubes, appropriate technologies for the production of the tube have been developed.     

直流叠加脉冲电压下FLTD气体开关击穿特性

分析了直流叠加脉冲电压(定义为复合电压)下次级感应电压触发快脉冲直线变压器驱动源(FLTD)中气体开关击穿延时过程,给出了击穿延时的估算公式。初步实验研究了FLTD用三电极气体开关在复合电压作用下的击穿特性,结果表明:在±70kV直流充电电压叠加300kV/30ns快脉冲电压的复合电压作用下,气体开关的击穿延时小于相同工作系数下常规触发方式的击穿延时,采用SF6气体绝缘时,击穿延时较常规触发方式减小了17%~30%;采用N2绝缘时,减小了约50%,开关工作系数为55%时,击穿延时抖动小于5ns;理论估算的复合电压下击穿延时与实测结果基本吻合。     

一种用于触发引燃管的脉冲电源

设计了一种单电源的变压器型高电压、大电流脉冲源。该电源只有一套放电电容,以晶闸管作为放电开关,单原边双副边的脉冲变压器作为传输线。利用二极管的单向导通特性,使变压器根据负载不同的工况运行在不同的状态,分时输出高电压、大电流脉冲。该设计利用变压器在空间上将高压输出回路和低压控制回路隔离,与一般的双电源设计方式相比,降低了驱动电路的成本,减少了装置的体积,有利于设备的小型化和紧凑化。试验结果表明:当原边18 μF的储能电容充电电压为700 V时,通过晶闸管开关控制电容向2 ∶2 ∶20的单原边双副边脉冲变压器放电,副边开路时输出幅值7.6 kV、上升沿432 ns的开路电压,副边短路时输出幅值690 A、半高宽15.6 μs、前沿7.0 μs的短路电流,满足NL37248引燃管的触发要求。     

用压电聚合物构成的单极性声脉冲发生器

本文介绍了用阶跃电压的快速下降沿作用在PVDF压电膜上而产生的单极性声脉冲。实验结果表明，声脉冲的波形和脉冲宽度取决于PVDF压电膜的厚度，阶跃电压的下降沿宽度，以及背衬材料和声传播媒质的形状等多个因素。该声脉冲发生器所产生的压力波脉冲的宽度约为50ns，不仅适用于固体中空间电荷的测量，也可以用于其他方面的应用，例如超声医学诊断，对材料的非破坏性的检测等。文章以该声脉冲发生器在压电压力波中的应用为例进行论述，并且所有测量结果都是通过压电压力波测试系统获得的。     

铌镁酸铅-钛酸铅铁电阴极电子发射特性

研究了铌镁酸铅-钛酸铅铁电材料的铁电、介电性能对阴极发射阈值电压的影响, 以及铁电阴极发射电流与激励脉冲电压和抽取电压之间的关系, 并分析了其发射机理. 结果表明, 室温介电常数高、极化强度变化量大的弛豫铁电体0.9Pb(Mg_1/3Nb_2/3)O₃-0.1PbTiO₃具有较小的发射阈值电压; 铁电阴极电子发射与快极化反转和等离子体的形成有关; 由极化反转所致电子发射的自发射电流随激励脉冲电压的增大呈幂律增长关系, 其发射电流开始于激励脉冲电压的下降沿; 在抽取电压较大时, 发射电流随抽取电压的增大呈线性增长关系, 说明大电流主要取决于抽取电压; 其发射电流开始于激励脉冲电压的上升沿, 与“三介点”处的场增强效应和等离子体的形成有关; 当抽取电压为2500 V 时, 得到的发射电流幅值为210 A, 相应的电流密度为447 A/cm².     

Effect of the shape of the light pulse on the optical breakdown threshold of transparent dielectrics

The problem concerning the nonsteady heating by a light pulse of arbitrary shape, of an insulated metallic microparticle located in a transparent dielectric, is solved. The effect of the shape of the heating pulse on the nature of heating up of the inclusion is investigated. The results of the paper can be used for the experimental verification of the heat-conductivity theory of breakdown of solid transparent dielectrics.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 2, pp. 77–81, February, 1979.In conclusion, the authors thank V. A. Gorshkov for assistance in carrying out the calculations.