Enzyme sensor for L-lactate with a chitosan-mercury film electrode

Summary An amperometric enzyme sensor composed of a mercury film electrode and an enzyme-immobilized chitosan membrane is developed. This biosensor is based on both a mercury film electrode detecting the consumption of dissolved dioxygen following enzymatic reaction, and a chitosan membrane. The latter provides an excellent permselectivity and excludes electroactive interferents. The detection range of this biosensor was 1.0×10^–5–3.0×10^–4 mol/l and the relative standard deviation, R.S.D. at 5.0×10^–5 mol/l was 1.4% (n=3). This biosensor was applied to the direct determination of L-lactate in human serum without pretreatment.     

Determination of morphine in process streams by sequential injection analysis with chemiluminescence detection

A procedure for the determination of morphine in process streams by sequential injection analysis based on the chemiluminescence reaction of morphine with acidic potassium permanganate in the presence of sodium hexametaphosphate is presented. The chemiluminescence emission has been monitored using an in-house detection system which consisted of a fibre optic flowthrough cell and a sensitive, low dark current, photomultiplier tube. The calibration graph (range 2 × 10^–8 to 1 × 10^–4 mol/l) was not linear over the entire range of concentration, with a polynomial equation of best fit of y = 1.0 × 10¹⁵ x³ – 2.2 × 10¹¹ x² + 1.3 × 10⁷ x – 8.3. The calibration function approximates linearity over the concentration range 2.5 × 10^–6 to 3.0 × 10^–5 mol/l where the slope of the log-log plot is 1.09 ± 0.16. The detection limit was estimated at about 10^–8 mol/l from the response of the lowest calibration standard (2.5 × 10^–8 mol/l) which gave a signal to noise ratio of 3 : 1. Although the structurally related codeine did not interfere significantly the results suggest that this method may be susceptible to matrix effects, dependent on the location of sampling from the process stream.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

Adsorptive stripping voltammetric determination of 1-(4′-bromophenyl)-3,3-dimethyltriazene

The optimum conditions were established for the determination of the genotoxic substance 1-(4-bromophenyl)-3,3-dimethyltriazene by differential-pulse voltammetry at a hanging mercury drop electrode in the concentration range 1 × 10^–4 to 1 × 10^–7 mol dm^–3. The sensitivity of the determination can be improved through adsorptive accumulation of the investigated substance on the surface of the hanging mercury drop electrode: differential pulse adsorptive stripping voltammetry can be used in the concentration range 1 × 10^–7 to 2 × 10^–10 mol dm^–3. The relative standard deviation (for ten determinations at 2 × 10^–10 mol dm^–3) was 7.5%.     

Simultaneous determination of sodium dodecyl sulphate and sodium linear-dodecylbenzenesulphonate with 1-stearyl-4-(4-aminonaphthylazo)-pyridinium bromide by spectrophotometry

A rapid and sensitive spectrophotometric method for the simultaneous determination of sodium dodecyl sulphate (SDS) and sodium linear-dodecylbenzenesulphonate (DBS) with 1-stearyl-4-(4-aminonaphthylazo)-pyridinium bromide (SAPB) is described using the difference at the maximum absorption wavelength of the SDS- and the DBS-ion associate. SDS and DBS have been determined independently by measuring their respective absorbances at the maximum absorption wavelength. The apparent molar absorptivities of the SDS- and the DBS-ion associate are 8.0×10⁴ l mol^–1 cm^–1 at 445 nm and 4.5×10⁴ l mol^–1 cm^–1 at 424 nm, respectively. The calibration graph for SDS is linear in the range from 0.1 to 1.0×10^–6 mol/l in the presence of 1.2×10^–6 mol/l DBS and for DBS from 0.8 to 2.0×10^–6 mol/l in the presence of 8.0×10^–7 mol/l SDS. The relative standard deviation (n=15) for 8.0×10^–7 mol/l SDS is 3.4% and for 1.6×10^–6 mol/l DBS 2.1%. The proposed method has been applied to the simulatenous determination of SDS and DBS in river water samples.     

Determination of traces of iron with the catalytic maximum wave in differential pulse polarography

Summary A differential pulse polarographic method for the determination of iron employing the catalytic maximum wave has been studied. A well-defined differential pulse polarographic peak for iron(III) in Britton-Robinson buffer solution containing 50 mol/l N-(2-hydroxyethyl) ethylenediamine N,N,N-triacetic acid (HEDTA) and 5 mmol/l KBrO₃ is observed in the potential range from +0.2 to –0.3 V vs. SCE. The peak current is very large compared to that of the Fe(III)/EDTA complex, being proportional to the concentration of iron(III) between 1.00×10^–8 and 3.58×10^–6 mol/l under optimum conditions. The relative standard deviations for 3.58×10^–7 mol/l and 1.79×10^–6 mol/l iron(III) were 1.38 and 0.54%, respectively (n=5), and the calculated detection limit was 5.2×10^–9 mol/l iron(III). The method has been applied to the determination of iron in fresh snow and rain waters.

---

Spurenbestimmung von Eisen mit Hilfe der katalytischen Maximumsstufe in der Differential-Puls-Polarographie

Zusammenfassung Das Verfahren beruht auf der Tatsache, daß in Britton-Robinson-Puffer (mit 50 mol/l HEDTA und 5 mmol/l KBrO₃) im Potentialbereich von +0,2 bis –0,3 V gegen SKE ein gut definierter puls-polarographischer Peak für Eisen(III) auftritt. Der Peakstrom ist im Vergleich zu dem des Fe(III)/EDTA-Komplexes sehr groß und ist unter optimalen Bedingungen im Konzentrationsbereich von 1,00·10^–8 bis 3,58·10^–6 mol/l der Eisen(III)-Konzentration proportional. Die relative Standardabweichung beträgt 1,38% bzw. 0,54% (n=5) für 3,58·10^–7 mol/l bzw. 1,79·10^–6 mol/l Fe(III). Die berechnete Nachweisgrenze liegt bei 5,2·10^–9 mol/l Fe(III). Das Verfahren wurde zur Eisenbestimmung in Schnee- und Regenwasser eingesetzt.

---

---

This work was supported in part by a Grant-in-Aid for Scientific Research from Hokkaido-prefecture, 1982.     

Determination of traces of vanadium with the catalytic maximum wave in differential pulse polarography

Summary A differential pulse-polarographic method has been studied for the determination of vanadium employing the catalytic maximum wave. A well-defined differential pulse polarographic peak is observed in the potential range from –0.2 to –0.7 V vs. SCE for vanadium(V) in 10 mmol 1^–1 NaCl containing 10 mmol 1^–1 acetic acid, 40 mmol 1^–1 pyrocatechol, and 2.5 mmol 1^–1 KBrO₃. The peak current is very large and proportional to the concentration of vanadium(V) between 1×10^–7 and 1×10^–6 mol 1^–1. The relative standard deviation at 0.5 mol l^–1 vanadium(V) was 2.06% (n=7). This method has been successfully applied to the determination of vanadium in standard materials such as pond sediment.

---

Spurenbestimmung von Vanadium mit Hilfe der katalytischen Maximumsstufe in der Differential-Puls-Polarographie

Zusammenfassung Ein gut definierter differentialpuls-polarographischer Peak wurde für Vanadium(V) in 10 mmol/l NaCl-Lösung, die 10 mmol/l Essigsäure, 40 mmol/l Brenzcatechin und 2,5 mmol/l KBrO₃ enthielt, beobachtet (Potentialbereich –0,2 bis –0,7 V gegen SCE). Der Peakstrom ist sehr groß und die Vanadiumkonzentration im Bereich von 1×10^–7 bis 1×10^–6 mol/l proportional. Die relative Standardabweichung betrug 2,06% (n=7) bei 0,5 mol/l Vanadium(V). Das Verfahren wurde mit gutem Erfolg zur Vanadiumbestimmung in Standardproben (z.B. Teichsediment) eingesetzt.

     

Flow injection analysis of gallic acid with inhibited electrochemiluminescence detection

A flow injection (FI)–electrochemiluminescent (ECL) method has been developed for the determination of gallic acid, based on an inhibition effect on the Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) ECL system in pH 8.0 phosphate buffer solution. The method is simple and convenient with a determination limit of 9.0×10^–9 mol/L and a dynamic concentration range of 2×10^–8–2×10^–5 mol/L. The relative standard deviation (RSD) was 1.0% for 1.0×10^–6 mol/L gallic acid (n=11). It was successfully applied to the determination of gallic acid in Chinese proprietary medicine—Jianming Yanhou Pian. The inhibition mechanism proposed for the quenching effect of the gallic acid on the Ru(bpy)₃²⁺/TPrA ECL system was the interaction of electrogenerated Ru(bpy)₃^2+* and o-benzoquinone derivative at the electrode surface. The ECL emission spectra and UV-visible absorption spectra were applied to confirm the mechanism.     

KMnO4-OP Chemiluminescence system for FIA determination of hydrogen peroxide

A fast and simple KMnO₄-OP chemiluminescence system for flow-injection analysis of hydrogen peroxide is described. When a mixture of sample and OP is injected into acidic KMnO₄, solution in a flow-cell, strong chemiluminescence occurs. The response is linear to the concentration of hydrogen peroxide in the range of 1.0 × 10^–8 to 6.0 × 10^–5 mol/l with 0.1 mol/l permanganate, and the upper limit of linear response could be extended to 6 × 10^–3 mol/l by increasing the permanganate concentration. The relative standard deviation of the method is between 1.6 and 2.3%. The detection limit is 6.0 × 10^–9 mol/l. This method is suitable for automatic and continuous analysis and has been successfully tested for determination of hydrogen peroxide in rain water. The chemiluminescence intensity was found to be remarkably enhanced in the presence of the OP micellar system.     

Polarographic study of a benzodiazepinooxazole: Oxazolam

Summary The polarographic behaviour of 10-chloro-2,3, 7,11b-tetrahydro-2-methyl-11b-phenyloxazolo-[3,2-d][1,4]-benzodiazepin-6(5H)-one (Oxazolam) was studied in the pH range 1–12. The reduction processes of Oxazolam and its hydrolysis product are irreversible and their currents are predominantly diffusion-controlled. The linear relationship between current and Oxazolam concentration in sulphuric acid medium permits its polarographic determination up to 6.08×10^–5 mol/l. The detection limit was 1.52×10^–7 mol/l (50 ppb). The reproducibility of the method in terms of relative standard deviation was 1.74% and 1.85% for ten determinations at 1.48×10^–5 mol/l and 1.37×10^–6 mol/l levels, respectively. The method developed was applied to the determination of the compound in its formulations, Hializan-10 mg, obtaining errors lower than 2%.

---

Polarographische Untersuchung eines Benzodiazepinoxazols: Oxazolam

     

Kinetic Determination of Mercury(II) at Trace Level from Its Catalytic Effect on a Ligand Substitution Process

A catalytic kinetic method (CKM) is presented for the determination of mercury(II) based on its catalytic effect on the rate of substitution of N-methylpyrazinium ion (Mpz⁺) onto hexacyanoferrate(II). The progress of the reaction was monitored spectrophotometrically at 655 nm by registering the increase in absorbance of the product [Fe(CN)₅(Mpz]²⁻ under the reaction conditions: 5 × 10⁻³ mol L⁻¹ [Fe(CN)₆]⁴⁻), 5 × 10⁻⁵ mol L⁻¹ [Mpz⁺], T = 25.0 ± 0.1°C, pH 5.00 ± 0.02 and ionic strength, I = 0.1 mol L⁻¹ (KNO₃). Quantitative rate data at specified experimental conditions showed a linear dependence of the absorbance after fixed time A _t on the concentration of mercury(II) catalyst in the range 20.06–702.1 ng mL⁻¹. The maximum relative standard deviations and percentage errors for the determination of mercury(II) in the range of 20.06–200.6 ng mL⁻¹ were calculated to be 1.7 and 2.7% respectively. The detection limit was found to be 7.2 ng mL⁻¹ of mercury(II). Accuracy (expressed in terms of recoveries) was in the range of 98–103%. Figures of merit and interference due to many cations and anions was investigated and discussed. The applicability of the method was demonstrated by determining the mercury(II) in different synthetic samples and confirming the results using atomic absorption spectrophotometry. The proposed method allowed determination of mercury(II) in the range 20.06–702.1 ng mL⁻¹ with very good selectivity and an output of 30 samples h⁻¹.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 654–661.Original English Text Copyright © 2005 by Surendra Prasad.This article was submitted by the author in English.     

Determination of nanomolar levels of guanine by differential-pulse adsorptive cathodic stripping voltammetry of its copper(II) complex

Guanine is determined at the 5.0×10^–10 –2.0×10^–7 mol/l level by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper (II) complex at –0.21 V vs. Ag-AgCl electrode. The optimum analytical conditions were found to be Britton-Robinson buffer solution (pH 4.8), an accumulation potential of 0.0 V and an accumulation time of 3 min. Under these conditions, the detection limit is 5.0×10^–10 mol/l and the relative standard deviation 2.6% for 1.0×10^–7 mol/l guanine. The method is compared with the previous voltammetric methods. The presence of some purine derivatives does not interfere.     

Voltammetric trace determination of ubiquinones at mercury electrodes

Summary Voltammetric methods were developed for the determination of ubiquinones on the basis of their adsorption and redox behaviour at mercury electrodes. Linear calibration plots were obtained in the concentration range between 10^–4 mol/l and 2.3·10^–5 mol/l from differential pulse voltammetric measurements under experimental conditions avoiding significant adsorption of the analyte. A remarkable decrease of the detection limit down to 10^–7 mol/l was achieved with the help of adsorptive accumulation of ubiquinone molecules at the mercury electrode followed by differential pulse detection. The resulting non-linear calibration plot was explained with a model, which takes into account both adsorption and diffusion of the analyte.     

The Effect of Aggregation in Aqueous Aerosil Dispersions on Their Structure and Mechanical Properties

The dynamics of the structure disintegration in the A-175 aerosil dispersions in water and sodium dodecylbenzenesulfonate (SDBS) aqueous solutions was studied by the rotational viscometry. The aqueous dispersions of aerosil were found to be characterized by a high degree of aggregation. At the volume content of the dispersed phase = 0.063–0.082, the flow of the dispersions is described in terms of the theory of highly aggregated systems. The effect of SDBS on the flow behavior of aerosil dispersions is complex. There is a range of SDBS concentrations (C = 2.87 × 10^–6–1.44 × 10^–5 mol/l) where it has a noticeable structuring effect. Aerosil dispersions in micellar SDBS solutions (C > 3.0 × 10^–3 mol/l) demonstrated the behavior of slightly structured systems characterized by the quasi-Newtonian flow.     

A study on terbium sensitized chemiluminescence of ciprofloxacin and its application

A novel rapid flow injection method with chemiluminescence (CL) detection was established for the determination of ciprofloxacin (CPLX), which is an antibiotic commonly used. The method is based on CL of Ce(IV)–SO₃²⁻ sensitized by Tb³⁺–CPLX, and showed the intensive bands characteristic of Tb³⁺ (⁵D₄→⁷F₅). The optimum conditions for CL emission were investigated. The linear relationship between the relative CL intensity and the concentration of CPLX is in the range of 9.0×10⁻⁹–1.0×10⁻⁶ mol/l with a detection limit of 3.1×10⁻¹⁰ mol/l. The relative standard deviation is 2.8% (n=11) for a level of 5.0×10⁻⁸ mol/l. The method was applied to the analysis of CPLX in human serum and urine samples with satisfactory results. The possible mechanism for this sensitized CL reaction is also discussed.     

Determination of pipemidic acid based on flow-injection chemiluminescence due to energy transfer from peroxynitrous acid synthesized on-line

A flow-injection chemiluminescence (CL) method for the determination of pipemidic acid is described. It is based on energy transfer from excited state peroxynitrous acid to pipemidic acid, in which the excited state peroxynitrous acid is synthesized on-line by the mixing of acid hydrogen peroxide with nitrite in a flow system and the CL is from two excited states of pipemidic acid. The proposed method allows the measurement of pipemidic acid over the range of 2.0×10^–7–2.0×10^–5 mol l^–1 . The detection limit is 6.3×10^–8 mol l^–1, and the relative standard deviation for 2.0×10^–6 mol l^–1 pipemidic acid (n= 9) is 0.9%. This method was evaluated by the analysis of pipemidic acid in pharmaceutical preparations.     

Determination of oxytetracycline in urine and human serum by differential pulse polarography

Summary A differential pulse polarographic method for the determination of oxytetracycline in urine and human serum in acid media (HClO₄ of pH 2) is proposed. The effects of the amount of sample taken and the concentration of HClO₄ present were investigated. The detection limit was 5.5×10^–6 mol/l. The standard deviation of the determination of 5.5×10^–5 mol/l of oxytetracycline in 2 ml of urine was 1.7×10^–6 mol/l and that of the determination of 5.5×10^–5 mol/l of oxytetracycline in 2 ml of human serum was 1.9×10^–6 mol/l.

---

Bestimmung von Oxytetracyclin in Urin und Humanserum durch Differential-Pulspolarography

     

Electrochemical Determination of Tannins Using Multiwall Carbon Nanotubes Modified Glassy Carbon Electrode

A novel chemically modified electrode is prepared on the basis of the attachment of multiwall carbon nanotubes (MWNTs) to the surface of a glassy carbon electrode (GCE) in the presence of a hydrophobic surfactant. The electrochemical behavior of tannins at the MWNTs-modified GCE is investigated. Tannins yield a well-defined oxidation at about 0.30 V (SCE) at the MWNTs-modified GCE. MWNT-film shows remarkable enhancement effect on the oxidation peak current of tannins. The experimental parameters are optimized, and a direct electrochemical method to detect tannins is proposed. The oxidation peak current is proportional to the concentration of tannins over the range from 4 × 10^–7 to 2 × 10^–4 M, and the detection limit is 1 × 10^–7 mol/l after 5 min of accumulation. The relative standard deviation of 6% for determination of 2 × 10^–6 mol/l tannins indicates excellent reproducibility. The analysis method is demonstrated by using tea and Chinese gall samples.     

Determination of Mo(VI) with 2-benzylideneiminobenzohydroxamic acid (2-BIBH) in urine by cathodic stripping voltammetry

Summary Controlled adsorptive accumulation of Mo(VI)-2-BIBH at the hanging mercury drop electrode (HMDE) provides the basis for the direct stripping measurement of Mo(VI) in nanomolar concentration. The cathodic stripping response is evaluated with respect to experimental parameters such as preconcentration time, preconcentration potential and others. A differential pulse cathodic stripping voltammetric method for the determination of Mo(VI) with 2-BIBH in urine is proposed. The detection limit is 10^–9 mol/l Mo(VI), standard deviation for 5×10^–8 mol/l is ±1.58×10^–9 mol/l.

---

Bestimmung von MolybdÄn(VI) mit 2-BenzylideniminobenzohydroxamsÄure (2-BIBH) in Harn durch kathodische Stripping-Voltammetrie

     

Selective method for the determination of gold by anodic stripping voltammetry

A highly selective method for the deter- mination of gold by anodic stripping voltammetry is described. For preconcentration a glassy carbon electrode, activated by deposition of small amounts of gold before the measurement, is proposed. The Au³⁺ reduction process at such an electrode is effective starting with the potential +0.4 V vs. Ag/AgCl electrode. A linear dependence of the current of the gold stripping peak on the gold concentration was obtained in the range from 5×10^–8 to 1×10^–6 mol/l. The relative standard deviation for 2×10^-7 mol/l HAuCl₄ was 4.2% (n=5). The detection limit was 4×10^-9 mol/l. The accuracy of the method was verified by the determination of gold in reference materials.