High temperature liquid chromatography of intact proteins using organic polymer monoliths and alternative solvent systems

Alternative approaches to conventional acetonitrile gradient methods for reversed-phase liquid chromatographic analysis of intact proteins have been investigated using commercial poly(styrene-co-divinylbenzene) monolithic columns (Dionex ProSwift™ RP-2H and RP-4H). Alternative solvents to acetonitrile (2-propanol and methanol) coupled with elevated temperatures demonstrated complementary approaches to adjusting separation selectivity and reducing organic solvent consumption. Measurements of peak area at increasing isothermal temperature intervals indicated that only minor (<5%) decreases in detectable protein recovery occurred between 40 and 100 °C on the timescale of separation (2–5 min). The reduced viscosity of a 2-propanol/water eluent at elevated temperatures permitted coupling of three columns to increase peak production (peaks/min) by 16.5%. Finally, narrow-bore (1 mm i.d.) columns were found to provide a more suitable avenue to fast, high temperature (up to 140 °C) separations.     

Determination of pharmaceutically related compounds by suppressed ion chromatography: I. Effects of organic solvent on suppressor performance

This overall study aims to investigate gradient elution ion-exchange chromatography of pharmaceutically relevant compounds using universal nebulisation detectors, such as evaporative light scattering detection (ELSD). Addition of organic solvents to the eluent is necessary to minimise hydrophobic adsorption on the polymeric stationary phase and improve solubility of analytes. It is also necessary to de-salt the eluent prior to detection, and in this work, ion chromatography suppressors were used for this step. Such suppressors have been designed for aqueous eluents, so the purpose of the present study was to investigate the effects of methanol and acetonitrile on suppressor performance. Chemical and electrolytic suppressors were evaluated for baseline drift, noise and efficiency of suppression using aqueous/organic eluents containing up to 40% (v/v) methanol or acetonitrile. Chemical suppression of aqueous/organic eluents showed minimal noise levels, uniform low baseline and low gradient drift. Electrolytic suppression gave good performance, but with higher baseline conductivity levels and baseline drift than chemical suppression. The elevated baseline was found not to be caused by incomplete suppression of the eluent, but was attributed to chemical reactions involving the organic solvents and facilitated by high electric currents and heat generation. It was demonstrated that suppressed ion-exchange separation using a complex KOH elution profile could be coupled with ELSD, with the suppressor effectively de-salting the eluent, producing a stable baseline. Finally, complementary separation selectivity was demonstrated using a set of pharmaceutically related organic acids separated by reversed-phase and ion-exchange methods.     

Peptide mapping with mobile phases of intermediate pH value using capillary reversed-phase high-performance liquid chromatography/electrospray ionisation tandem mass spectrometry

This investigation describes the separation of tryptic peptides by capillary reversed-phase high-performance liquid chromatography (RP-HPLC) with eluents in the intermediate pH range, followed by in-line electrospray ionisation tandem mass spectrometry (ESI-MS/MS) analysis. For these purposes, gradient elution procedures with an aqueous eluent containing 20 mM ammonium formate, and an increasing content of acetonitrile or methanol, were employed. Compared to the analysis of the same tryptic peptides under low-pH conditions with an ion-pairing reagent, the increase in the pH with the 20 mM ammonium formate mobile phase led to significant changes in both peptide retention to the reversed-phase column and the collision-induced dissociation at the MS/MS stage as a consequence of the changes in the physico-chemical properties of these peptides, such as their overall charge, polarity and relative hydrophobicity. Thus, improved selectivity for the peptide separation and favourable tandem mass spectrometry analysis could be obtained with eluents in this intermediate pH range. The number of tryptic peptides identified by the new approach for the proteins investigated were significantly higher than that obtained by the conventional low-pH methods. Moreover, analysis of protein digests at very low concentrations was also performed under both acidic and intermediate pH conditions and similar improvements in selectivity and MS/MS detection limits were observed, i.e. identification of more distinct peptides and higher sequence coverage of the protein was obtained when eluents of intermediate pH were employed. This study therefore highlights the potential of conducting peptide mapping in the intermediate pH range to achieve more reliable and sensitive protein identifications with capillary RP-HPLC–ESI-MS/MS.     

A new capillary electrophoresis buffer for determining organic and inorganic anions in electroplating bath with surfactant additives

Monitoring of trace impurities in electroplating bath is needed to meet EU requirements for WEEE and RoHS and for quality control of electrodeposits. Methods using IC and 100% aqueous CE buffer were found producing non-repeatable results attributed to interference of surfactants and major methanesulphonate anion. A new CE buffer containing 1.5 mM tetraethylenepentaamine, 3 mM 1,3,5-benzenetricarboxylic acid and 15 mM Tris in 20% (v/v) methanol at pH = 8.4 was shown to enhance the separation window, reduce interaction between buffer and bath constituents, and give satisfactory repeatability with baseline separation for 14 organic and inorganic anions within 14 min, good repeatability for migration time (0.32–0.57% RSD), satisfactory peak area and peak height (2.9–4.5 and 3–4.7% respectively), low detection limit (S/N = 2, 20–150 ppb), and wide working ranges (0.1–100 ppm). The CE buffer with 20% (v/v) methanol has demonstrated its capability for identifying anion impurities causing problem in aged tin bath and the use of only 10-fold dilution to produce reliable results for quality assessment in plating bath containing high surfactant additives.     

Influence of Physicochemical Parameters of Some Ring-Substituted Phenol Derivatives on Their Retention on a Porous Graphitized Carbon Column

Abstract

The retention characteristics of 29 phenol derivatives were determined on a porous graphitized carbon column in unbuffered acetonitrile—water and methanol—water eluent mixtures at various organic phase concentrations. Each phenol derivative showed symmetric peaks in each eluent without buffers. Good linear correlations were found between the log k' value and the organic mobile phase concentration in the eluent. Principal component analysis indicated that methanol and acetonitrile expose different selectivities. Stepwise regression analysis proved that the retention of ring—substituted phenol derivatives is mainly governed by the sterical parameters, electron-withdrawing power and hydrogen donor capacity of substituents. According to the results of Free-Wilson analysis, the substituents with large steric parameters, strong electron-withdrawing power and hydrogen donor capacity have the highest impact on the retention. The lipophilicity of phenol derivatives did not affect significantly the retention, although the eluents were typical reversed-phase eluents.     

Influence Of Organic Modifiers On The Retention Characteristics Of Graphitized Carbon Column

Abstract

The retention time of α-(1,1,3,3-tetramethylbutyl)phenyl ethylene oxide oligomer surfactants was determined on a porous graphitized carbon column (PGC) in eluents containing acetonitrile, methanol, ethanol, 2-propanol, tetrahydrofuran, dioxane and 2-ethoxyethanol as organic modifier. Linear relationships were calculated between the logarithm of the capacity factor and the concentration of organic modifier in the eluent. Ethylene oxide oligomers were well separated on the PGC column in acetonitrile-water eluent mixtures. Oligomers were not separated in eluents containing 2-propanol, tetrahydrofuran. dioxane and 2-ethoxyethanol as organic modifier. This result was explained by the supposition that the bulky organic modifiers occupy the active adsorption centers on the PGC surface decreasing in this manner the separation efficiency of the support.     

Investigation of polar organic solvents compatible with Corona Charged Aerosol Detection and their use for the determination of sugars by hydrophilic interaction liquid chromatography

A range of organic solvents (ethanol, isopropanol and acetone) has been investigated as alternatives to acetonitrile and methanol when used in conjunction with Corona Charged Aerosol Detection (Corona CAD). These solvents have been evaluated with regard to their effect on the response of the Corona CAD. Three dimensional response surfaces were constructed using raw data showing the relationship between detector response, analyte concentration and percentage of organic solvent in the mobile phase, using sucralose or quinine as the test analyte. The detector response was non-linear in terms of analyte concentration for all solvents tested. However, detector response varied in an approximately linear manner with percentage of organic solvent over the range 0–40% for ethanol or isopropanol and 0–80% for acetone and methanol. The chromatographic performance of the various solvents when used as aqueous–organic mobile phases was evaluated for isocratic and gradient separations of sugars and sugar alcohols by hydrophilic interaction liquid chromatography (HILIC) using an Asahipak NH2P-504E column coupled with Corona CAD detection. It was found that whilst acetonitrile provided the highest column efficiencies and lowest detection limits of the solvents studied, acetone also performed well and could be used to resolve the same number of analytes as was possible with acetonitrile. Typical efficiencies and detection limits of 5330 plates m⁻¹ and 1.25 μg mL⁻¹, respectively, were achieved when acetone was used as the organic modifier. Acetone was utilised successfully as an organic modifier in the HILIC separation of carbohydrates in a beer sample and also for a partially digested dextran sample.     

Analysis of oligosaccharides using aminobonded silica gel and a ternary eluent with evaporative light scattering detection

Using two commercial, amino bonded, silica gel columns, binary eluents (methanol/water, acetonitrile/methanol) and ternary eluents (acetonitrile/methanol/water) are evaluated for their ability to separate oligosaccharides in comparison with classical acetonitrile/water eluents. Chromatographic data on glucose, maltose, raffinose, stachyose and maltodextrin are reported. Mobile phases consisting of acetonitrile/water or acetonitrile/methanol/water produce the best separations. Phase hydrolysis is evaluated using an evaporative light scattering detector. The reduction of the water content in the eluent stabilizes the aminocolumns and the life time of the amino columns should be improved with the ternary eluent. Moreover, a better detection limit can be obtained. Capabilties to run gradient elution without baseline drift are clearly demonstrated.     

Detection of albiflorin and paeoniflorin in Paeoniae Radix by reversed-phase high-performance liquid chromatography with pulsed amperometric detection

We have developed a reversed-phase high-performance liquid chromatography-pulsed amperometric detection (RP-HPLC-PAD) method for the detection of albiflorin and paeoniflorin in Paeoniae Radix and Wu-ji-san. Albiflorin and paeoniflorin were completely separated using 10% acetonitrile in 5 mM sodium phosphate buffer (pH 3.0) as an eluent and detected by PAD under alkaline conditions after using a post-column delivery system. The limit of detection (S/N = 3) and the limit of quantification (S/N = 10) were 0.10 and 0.35 ng for albiflorin, and 0.20 and 0.50 ng for paeoniflorin, respectively. The coefficients of linear regression were 0.9995 and 0.9999 for concentrations between 0.035 and 100 μg/mL. The intra- and inter-day precision (RSDs) was less than 3.56% in Paeoniae Radix and Wu-ji-san. The average recoveries from Paeoniae Radix and Wu-ji-san were 99.01–100.94% and 99.46–100.64%. This method shows higher selectivity than HPLC–UV method for analyzing albiflorin and paeoniflorin in Chinese medicinal preparation.     

Simultaneous determination of nine trace mono- and di-chlorophenols in water by ion chromatography atmospheric pressure chemical ionization mass spectrometry

A novel analytical method was proposed for the rapidly simultaneous determination of nine mono-chlorophenols (MCPs) and di-chlorophenols (DCPs) in water samples using eluent generator ion chromatography (IC) coupled with an atmospheric pressure chemical ionization mass spectrometry (APCI-MS) in the negative mode. The IC separation was carried out on an IonPac^® AS11 analytical column (250 mm × 4.0 mm) using gradient KOH containing 15% acetonitrile as organic modifier at a constant flow rate of 1.0 mL/min. The molecular ions m/z [M − H]⁻ 127 and 161 were selected for the quantification in selected ion monitoring (SIM) mode for MCPs and DCPs, respectively. The average recoveries were between 80.6% and 92.6%. Within-day and day-to-day relative standard deviations were less than 12.1% and 13.3%, respectively. The method allowed the nine objective compounds in water samples to be determined at μg/L levels. It was confirmed that this method could be used in routine analysis.     

反相离子对色谱中有机溶剂浓度和离子对试剂浓度对保留值的影响

我们测定了氨基苯磺酸和氨基萘磺酸在反相离子对色谱中不同乙腈/水, 甲醇/水配比和离子对试剂浓度下的保留值,并把两种冲洗剂下的保留值和关系式lnk'=a+C~c~b中的参数a,C作线性关联,得到很好的相关性,这表明有机溶剂乙腈和甲醇对选择性并无显著的影响,但乙腈有更大的冲洗强度.证明关系式lnk'=A+Blnc~p+C~c~ b能较好地描述有机溶剂和离子对试剂浓度对保留值的影响, 但当离子对试剂浓度较高时该关系式不成立.同时提出了有机溶剂浓度和离子对试剂浓度"等同效应" 的概念     

Selective extraction of triazine herbicides from food samples based on a combination of a liquid membrane and molecularly imprinted polymers

A selective extraction technique based on the combination of liquid membrane (microporous membrane liquid–liquid extraction) and molecularly imprinted polymers (MIP) was applied to triazines herbicides in food samples. Simazine, atrazine and propazine were extracted from aqueous food samples through the hydrophobic porous membrane that was impregnated with toluene, which also formed part of the acceptor phase. In the acceptor phase, the compounds were re-extracted onto MIP particles. The extraction technique was optimised for the amount of molecularly imprinted polymers particles in the organic acceptor phase, extraction time, and type of organic acceptor solvent and desorption solvent. An extraction time of 90 min and 50 mg of MIP were found to be optimum parameters. Toluene as the acceptor phase was found to give higher triazines binding onto MIP particles compared to hexane and combinations of diethyl ether and hexane. 90% methanol in water was found to be the best desorption solvent compared to acetonitrile, methanol and water. The selectivity of the technique was demonstrated by extracting spiked lettuce and apple extracts where clean chromatograms were obtained compared to liquid membrane extraction alone or to the microporous membrane liquid–liquid extraction – non-imprinted polymer combination. The MIP showed a certain degree of group specificity and the extraction efficiency in lettuce extract was 79% (0.72) for simazine, 98% (1.55) for atrazine and 86% (3.08) for propazine.     

Effect of ion-exchange site and eluent modifiers on the anion-exchange of carboxylic acids

The chromatographic behavior of carboxylic acids has been investigated, on three different latex-based anion-exchange columns, in order to define the effect of the ion-exchange site structure on selectivity. The analytical columns produced are characterized by alkyl amines containing zero, one or two hydroxyl groups on the anion-exchange functional site. Divalent carboxylic acids, namely fumaric, maleic, trans-beta-hydromuconic, trans,trans-muconic, oxalic, malonic, succinic, glutaric, adipic, malic, tartaric and mucic acids, have been chosen as test solutes. The performance of the three stationary phases has been studied employing NaOH eluents and has been discussed with respect to the different hydrophilicity of the ion-exchange sites and analytes. Considering on previous results obtained using organic solvents (methanol and acetonitrile) with carbonate eluents on a highly hydrophilic column, the performance of the three exchangers has also been studied using acetonitrile, methanol and n-propanol. The chromatographic behavior was similar for the three columns studied, but the different organic solvents gave variations in selectivity. In order to characterize these differences, particle size measurements of the latices were performed both in pure water and in the presence of each organic solvent studied.     

Influence of organic solvents in the mobile phase on the determination of carboxylic acids and inorganic anions in grape juice by ion chromatography

Investigations have been initiated to develop a sufficiently good separation of both major and minor organic acids and inorganic anions present in grape musts using a Dionex As11 column, a sodium hydroxide gradient elution and a suppressed conductivity detection. Separation was complicated in aqueous mobile phase by co-elutions and selectivity was optimized using organic modifiers that alter ion-exchange selectivity for hydrophobic ions. In this study, the influence of three different solvents (methanol, ethanol and acetonitrile) on the efficiency of column was compared. The best separation of all ions in a synthetic solution was achieved with an eluent containing 13% (v/v) methanol and 13% (v/v) ethanol in water, the run during only 20 min. This method was next applied to grape juices with success and has shown sensitivity and reproducibility. Moreover, sample preparation was a simple 20-fold dilution with 0.45 microm filtration and direct injection without prior sample clean-up.     

Thin-layer chromatography of alkaloids on cyanopropyl bonded stationary phases. Part I

Selected alkaloids are chromatographed on cyanopropyl-silica thin layers using various nonaqueous and aqueous eluents. Because of the strong retention of these basic compounds, nonaqueous eluents containing medium polar diluents, strongly polar modifiers, and silanol blockers (ammonia or diethylamine) are required for separation. Likewise, aqueous eluents containing modifiers (acetonitrile, methanol, and tetrahydrofuran), buffered aqueous solutions at pH 2-8, ion-pair reagents [octane sulfonic acid sodium salt, sodium dodecyl sulphate, and bis-(2-ethylhexyl)phosphoric acid], or silanol blockers (ammonia, tetrabutyl ammonium chloride, and diethyl amine) are investigated. The separation selectivity as well as spot symmetry and efficiency system in the applied eluent systems are analyzed. The most selective and efficient systems are used in two-dimensional separations of isoquinoline alkaloids' mixture and the plant extracts Chelidonium majus, Fumaria officinalis, and Glaucium flavum. Two-dimensional thin-layer chromatography on cyanopropyl layer with diode array detection densitometry enables the separation and identification of some alkaloids in plant extracts.     

Optimization of matrix solid-phase dispersion extraction method for the analysis of isoflavones in Trifolium pratense

A method based on matrix solid-phase dispersion (MSPD) has been developed for the determination of 12 isoflavones in Trifolium pratense L. Dried leaf samples were blended with C₁₈, placed in small columns and isoflavones extracted with dichloromethane–methanol. Analyses were performed by high performance liquid chromatography with diode array detection (HPLC-DAD) with 2-methoxyflavone as internal standard. Several dispersants, eluents and clean-up steps were tested during the optimization of the process in order to obtain the best selectivity and yields. Mean recoveries ranged from 70% to 119%, with relative standard deviations <18%. The limits of detection were between 0.006 mg/l for biochanin A and 0.108 mg/l for daidzin. The performance of the optimized method in real samples was compared with a conventional method based in solid–liquid extraction (SLE).     

Method validation and comparison of acetonitrile and acetone extraction for the analysis of 169 pesticides in soya grain by liquid chromatography–tandem mass spectrometry

An acetonitrile-based extraction method for the analysis of 169 pesticides in soya grain, using liquid chromatography–tandem mass spectrometry (LC–MS/MS) in the positive and negative electrospray ionization (ESI) mode, has been optimized and validated. This method has been compared with our earlier published acetone-based extraction method, as part of a comprehensive study of both extraction methods, in combination with various gas chromatography–(tandem) mass spectrometry [GC–MS(/MS)] and LC–MS/MS techniques, using different detection modes. Linearity of calibration curves, instrument limits of detection (LODs) and matrix effects were evaluated by preparing standards in solvent and in the two soya matrix extracts from acetone and acetonitrile extractions, at seven levels, with six replicate injections per level. Limits of detection were calculated based on practically realized repeatability relative standard deviations (RSDs), rather than based on (extrapolated) signal/noise ratios. Accuracies (as % recoveries), precision (as repeatability of recovery experiments) and method limits of quantification (LOQs) were compared. The acetonitrile method consists of the extraction of a 2-g sample with 20 mL of acetonitrile (containing 1% acetic acid), followed by a partitioning step with magnesium sulphate and a subsequent buffering step with sodium acetate. After mixing an aliquot with methanol, the extract can be injected directly into the LC–MS/MS system, without any cleanup. Cleanup hardly improved selectivity and appeared to have minor changes of the matrix effect, as was earlier noticed for the acetone method. Good linearity of the calibration curves was obtained over the range from 0.1 or 0.25 to 10 ng mL⁻¹, with r² ≥ 0.99. Instrument LOD values generally varied from 0.1 to 0.25 ng mL⁻¹, for both methods. Matrix effects were not significant or negligible for nearly all pesticides. Recoveries were in the range 70–120%, with RSD ≤ 20%. If not, they were still mostly in the 50–70% range, with good precision (RSD ≤ 20%). The method LOQ values were most often 10 μg kg⁻¹ for almost all pesticides, with good repeatability RSDs. Apart from some minor pros and cons, both compared methods are fast, efficient and robust, with good method performances. The two methods were applied successfully in a routine analysis environment, during surveys in 2007 and 2008.     

Mobile phase selection for the combined use of liquid chromatography–inductively coupled plasma mass spectrometry and electrospray ionisation mass spectrometry

Four different organic solvents: dimethylformamide, 1,4-dioxane, n-propanol and ethanol were evaluated as alternative organic modifiers to acetonitrile for liquid chromatography (LC) separations. The aim was to establish common sets of chromatographic conditions that could be applied for LC hyphenation to inductively coupled plasma mass spectrometry (ICPMS) as well as to electrospray ionization MS (ESIMS). The approach was to evaluate candidate solvents that, compared to acetonitrile, potentially could give improved analytical performance (low solvent vapor loading, maximized analyte sensitivity and minimized carbon depositions on instrumental parts) in ICPMS analysis while retaining chromatographic and ESIMS performances. The study showed that dimethylformamide, 1,4-dioxane, n-propanol and ethanol all can be advantageous chromatographic modifiers for LC–ICPMS analysis, giving superior performance compared to acetonitrile. For the combined use of LC–ICPMS and LC–ESIMS with a common set of chromatographic conditions, n-propanol gave the best overall performance. The ¹⁹⁵Pt⁺ signal in ICPMS was continuously monitored during a 0–60% organic solvent gradient and at 25% of organic modifier, 100% of the signal obtained at the gradient start was preserved for n-propanol compared to only 35% of the signal when using acetonitrile. Platinum detection limits were 5–8 times lower using n-propanol compared with acetonitrile. Signal-to-noise ratio in continuous ESIMS signal measurements was 100, 90 and 110 for a 100 μg/ml solution of leucine–enkephaline using acetonitrile, ethanol and n-propanol, respectively. Chromatographic efficiency in reversed phase separations was preserved for n-propanol compared to acetonitrile for the analysis of the whole protein cytochrome C and the peptide bacitracin on a column with particle and pore sizes of 5 μm and 300 Å, but slightly deteriorated for the separation of the peptides leucine–enkephaline and bacitracin on a 3 μm and 90 Å column as the peak width at half height for both peptides increased by a factor of two. The performance on the smaller dimensioned column could however be improved by running the separations at 40 °C.     

Determination of madecassoside and asiaticoside contents of C. asiatica leaf and C. asiatica-containing ointment and dentifrice by HPLC-coupled pulsed amperometric detection

The present study reports the development and application of an HPLC-coupled pulsed amperometric detection method to determine the madecassoside and asiaticoside contents of Centella asiatica leaf and of commercial C. asiatica-containing ointment and dentifrice. C. asiatica, which was not pretreated, was extracted with 50% ethanol for 10 min. Madecassoside and asiaticoside were separated on a C18 column within 5 min using 25% (v/v) acetonitrile as the mobile phase. Both compounds were detected with high sensitivity when sodium hydroxide was used as a post-column eluent. Madecassoside and asiaticoside both displayed limits of detection of 0.005 μg/mL and linear regression coefficients of 0.9994 and 1.0000, respectively. The intra- and inter-day precisions were < 8.85% and average recovery was > 94.79%. The madecassoside and asiaticoside contents of ointment and dentifrice were successfully determined without sample purification or concentration owing to the high method sensitivity and selectivity.     

Effects of the operation parameters on Hydrophilic Interaction Liquid Chromatography separation of phenolic acids on zwitterionic monolithic capillary columns

Strongly polar phenolic acids are weakly retained and often poorly separated in reversed-phase (RP) liquid chromatography. We prepared zwitterionic polymethacrylate monolithic columns for micro-HPLC by in situ co-polymerization in fused-silica capillaries. The capillary monolithic columns prepared under optimized polymerization conditions show some similarities with the conventional particulate commercial ZIC-HILIC silica-based columns, however have higher retention and better separation selectivity under reversed-phase conditions, so that they can be employed for dual-mode HILIC-RP separations of phenolic acids on a single column. The capillary polymethacrylate monolithic sulfobetaine columns show excellent thermal stability and improved performance at temperatures 60–80 °C. The effects of the operation conditions on separation were investigated, including the type and the concentration of the organic solvent in the aqueous-organic mobile phase (acetonitrile and methanol), the ionic strength of the acetate buffer and temperature. While the retention in the RP mode decreases at higher temperatures in mobile phases with relatively low concentrations of acetonitrile, it is almost independent of temperature at HILIC conditions in highly organic mobile phases. The best separation efficiency can be achieved using relatively high acetate buffer ionic strength (20–30 mmol L⁻¹) and gradient elution with alternately increasing (HILIC mode) and decreasing (RP mode) concentration of aqueous buffer in aqueous acetonitrile. Applications of the monolithic sulfobetaine capillary columns in alternating HILIC-RP modes are demonstrated on the analysis of phenolic acids in a beer sample.