Flow injection chemiluminescence sensor based on core–shell magnetic molecularly imprinted nanoparticles for determination of sulfadiazine

A novel flow injection chemiluminescence (FI-CL) sensor for determination of sulfadiazine (SDZ) using core–shell magnetic molecularly imprinted polymers (MMIPs) as recognition element is developed. Briefly, a hydrophilic MMIPs layer was produced at the surface of Fe₃O₄@SiO₂ magnetic nanoparticles (MNPs) via combination of molecular imprinting and reversible stimuli responsive hydrogel. And it provided the MMIPs with excellent adsorption capacity and rapid adsorption rate due to the imprinted sites mostly situated on the surface of MMIPs. Then the prepared SDZ-MMIPs were packed into flow cell to establish a novel FI-CL sensor. The sensor provided a wide linear range for SDZ of 4.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.54 × 10⁻⁷ mol L⁻¹. And the relative standard deviation (RSD) for the determination of 1.0 × 10⁻⁶ mol L⁻¹ SDZ was 2.56% (n = 11). The proposed method was applied to determine SDZ in urine samples and satisfactory results were obtained.     

Barium alginate caged Fe3O4@C18 magnetic nanoparticles for the pre-concentration of polycyclic aromatic hydrocarbons and phthalate esters from environmental water samples

The hydrophobic octadecyl (C₁₈) functionalized Fe₃O₄ magnetic nanoparticles (Fe₃O₄@C₁₈) were caged into hydrophilic barium alginate (Ba²⁺-ALG) polymers to obtain a novel type of solid-phase extraction (SPE) sorbents, and the sorbents were applied to the pre-concentration of polycyclic aromatic hydrocarbons (PAHs) and phthalate esters (PAEs) pollutants from environmental water samples. The hydrophilicity of the Ba²⁺-ALG cage enhances the dispersibility of sorbents in water samples, and the superparamagnetism of the Fe₃O₄ core facilitates magnetic separation. With the magnetic SPE technique based on the Fe₃O₄@C₁₈@Ba²⁺-ALG sorbents, it requires only 30 min to extract trace levels of analytes from 500 mL water samples. After the eluate is condensed to 0.5 mL, concentration factors for both phenanthrene and di-n-propyl-phthalate are over 500, while for other analytes are about 1000. The recoveries of target compounds are independent of salinity and solution pH under testing conditions. Under optimized conditions, the detection limits for phenanthrene, pyrene, benzo[a]anthracene, and benzo[a]pyrene are 5, 5, 3, and 2 ng L⁻¹, and for di-n-propyl-phthalate, di-n-butyl-phthalate, di-cyclohexyl-phthalate, and di-n-octyl-phthalate are 36, 59, 19, and 36 ng L⁻¹, respectively. The spiked recoveries of several real water samples for PAHs and PAEs are in the range of 72-108% with relative standard deviations varying from 1% to 9%, showing good accuracy of the method. The advantages of the new SPE method include high extraction efficiency, short analysis time and convenient extraction procedure. To the best of our knowledge, it is unprecedented that hydrophilic Ba²⁺-ALG polymer caged Fe₃O₄@C₁₈ magnetic nanomaterial is used to extract organic pollutants from large volumes of water samples.     

Reprint of: Extraction of fluoxetine from aquatic and urine samples using sodium dodecyl sulfate-coated iron oxide magnetic nanoparticles followed by spectrofluorimetric determination

A new method based on the combination of magnetic solid phase extraction (MSPE) and spectrofluorimetric determination was developed for isolation and preconcentration of fluoxetine form aquatic and biological samples using sodium dodecyl sulfate (SDS) coated Fe₃O₄ nanoparticles (NPs) as a sorbent. The unique properties of Fe₃O₄ NPs including high surface area and strong magnetism were utilized effectively in the MSPE process. Effect of different parameters influencing the extraction efficiency of fluoxetine including the amount of Fe₃O₄ and SDS, pH value, sample volume, extraction time, desorption solvent and time were optimized. Under optimized condition, the method was successfully applied to the extraction of fluoxetine from water and urine samples and absolute recovery amount of 85%, detection limit of 20 μg L⁻¹ and a relative standard deviation (RSD) of 1.4% were obtained. The method linear response was over a range of 50–1000 μg L⁻¹ with R² = 0.9968. The relative recovery in different aquatic and urine matrices were investigated and values of 80% to 104% were obtained. The whole procedure showed to be conveniently fast, efficient and economical for extraction of fluoxetine from environmental and biological samples.     

Facile preparation of surface-exchangeable core@shell iron oxide@gold nanoparticles for magnetic solid-phase extraction: Use of gold shell as the intermediate platform for versatile adsorbents with varying self-assembled monolayers

The core@shell Fe₃O₄@Au nanoparticles (NPs) functionalized with exchangeable self-assembled monolayers have been developed for mode switching magnetic solid-phase extraction (MSPE) using high performance liquid chromatography with ultraviolet detection. The adsorbents were synthesized by chemical coprecipitation to prepare magnetic cores followed by sonolysis to produce gold shells. Functionalization of Fe₃O₄@Au NPs surface was realized through self-assembly of commercially available low molecular weight thiol-containing ligands using gold shells as intermediate platform and the dynamic nature of Au–S chemistry allowed substituent of one thiol-containing ligand with another simply by thiol exchange process. The resultant adsorbents were characterized by transmission electronic microscopy, Fourier transform infrared spectroscopy, elemental analysis, contact angle measurement, and vibrating sample magnetometry. To evaluate the versatile performance of the developed MSPE adsorbents, they were applied for normal-phase SPE followed by reversed-phase SPE. A few kinds of diphenols and polycyclic aromatic hydrocarbons (PAHs) were employed as model analytes, respectively. The predominant parameters affecting extraction efficiency were investigated and optimized. Under the optimum experimental conditions, wide dynamic linear range (6.25–1600 μg L⁻¹ for diphenols and 1.56–100 μg L⁻¹ for PAHs) with good linearity (r² ≥ 0.989) and low detection limits (0.34–16.67 μg L⁻¹ for diphenols and 0.26–0.52 μg L⁻¹ for PAHs) were achieved. The advantage of the developed method is that the Fe₃O₄@Au NPs could be reutilized for preconcentrating diverse target analytes in different SPE modes sequentially simply through treatment with desired thiol-containing ligands.     

Synthesis of magnetic framework composites for the discrimination of Escherichia coli at the strain level

Rapid and efficient characterization and identification of pathogens at the strain level is of key importance for epidemiologic investigations, which still remains a challenge. In this work, solvothermically Fe₃O₄-COOH@MIL-101 composites were fabricated by in situ crystallization approach. The composites combine the excellent properties of both chromium (III) terephthalate (MIL-101) and carboxylic-functionalized magnetite (Fe₃O₄-COOH) particles and possess the efficient peptides/proteins enrichment properties and magnetic responsiveness. Fe₃O₄-COOH@MIL-101 composites as magnetic solid phase extraction materials were used to increase the discriminatory power of MALDI-TOF MS profiles. BSA tryptic peptides at a low concentration of 0.25 fmol μL⁻¹ could be detected by MALDI-TOF MS. In addition, Fe₃O₄-COOH@MIL-101 composites were successfully applied in the selective enrichment of the protein biomarkers from bacterial cell lysates and discrimination of Escherichia coli at the strain level. This work provides the possibility for wide applications of magnetic MOFs to discriminate pathogens below the species level.     

Direct electrochemistry and electrocatalysis of hemoglobin immobilized in a magnetic nanoparticles-chitosan film

Magnetic nanoparticles (Fe₃O₄) were synthesized by a chemical coprecipitation method. X-ray diffraction (XRD) and transmission electron microscope (TEM) were used to confirm the crystallite structure and the particle's radius. The Fe₃O₄ nanoparticles and chitosan (CS) were mixed to form a matrix in which haemoglobin (Hb) can be immobilized for the fabrication of H₂O₂ biosensor. The Fe₃O₄-CS-Hb film exhibited a pair of well-defined and quasi-reversible cyclic voltammetric peaks due to the redox of Hb-heme Fe (III)/Fe (II) in a pH 7.0 phosphate buffer. The formal potential of Hb-heme Fe(III)/Fe(II) couple varied linearly with the increase of pH in the range of 4.0-10.0 with a slope of 46.5 mV pH⁻¹, indicating that electron transfer was accompanied with single proton transportation in the electrochemical reaction. The surface coverage of Hb immobilized on Fe₃O₄-CS film glassy carbon electrode was about 1.13 × 10⁻¹⁰ mol cm⁻². The heterogeneous electron transfer rate constant (k_s) was 1.04 s⁻¹, indicating great facilitation of the electron transfer between Hb and magnetic nanoparticles-chitosan modified electrode. The modified electrode showed excellent electrocatalytic activity toward oxygen and hydrogen peroxide reduction. The apparent Michaelis-Menten constant for H₂O₂ was estimated to be 38.1 μmol L⁻¹.     

Preparation of Fe3O4 nanoparticle enclosure hydroxylated multi-walled carbon nanotubes for the determination of aconitines in human serum samples

A magnetic carbon nanomaterial for Fe₃O₄ enclosure hydroxylated multi-walled carbon nanotubes (Fe₃O₄-EC-MWCNTs-OH) was prepared by the aggregating effect of Fe₃O₄ nanoparticle on MWCNTs-OH, and combined with high-performance liquid chromatography (HPLC)/diode array detection (DAD) to determine the aconitines (aconitine, hypaconitine and mesaconitine) in human serum samples. Compared with other extraction modes investigated in experiment, Fe₃O₄-EC-MWCNTs-OH sorbents showed a good affinity to target analytes. Some important parameters that could influence extraction efficiency of aconitines, including the extraction mode, amounts of Fe₃O₄-EC-MWCNTs-OH, pH of sample solution, extraction time, desorption solvent and desorption time, were optimized. Under optimal conditions, the recoveries of spiked serum samples were between 98.0% and 103.0%; relative standard deviations (RSDs) ranged from 0.9% to 6.2%. The correlation coefficients varied from 0.9996 to 0.9998. The limits of detection ranged from 3.1 ng mL⁻¹ to 4.1 ng mL⁻¹ at a signal-to-noise ratio of 3. The experimental results showed that the proposed method was feasible for the analysis of aconitines in serum samples.     

Extraction of trace amounts of mercury with sodium dodecyle sulphate-coated magnetite nanoparticles and its determination by flow injection inductively coupled plasma-optical emission spectrometry

A new method for solid-phase extraction and preconcentration of trace amounts Hg(II) from environmental samples was developed by using sodium dodecyle sulphate-coated magnetite nanoparticles (SDS-coated Fe₃O₄ NPs) as a new extractant. The procedure is based on the adsorption of the analyte, as mercury-Michler's thioketone [Hg₂(TMK)₄]²⁺ complex on the negatively charged surface of the SDS-coated Fe₃O₄ NPs and then elution of the preconcentrated mercury from the surface of the SDS-coated Fe₃O₄ NPs prior to its determination by flow injection inductively coupled plasma-optical emission spectrometry. The effects of pH, TMK concentration, SDS and Fe₃O₄ NPs amounts, eluent type, sample volume and interfering ions on the recovery of the analyte were investigated. Under optimized conditions, the calibration curve was linear in the range of 0.2-100 ng mL⁻¹ with r² = 0.9994 (n = 8). The limit of detection for Hg(II) determination was 0.04 ng mL⁻¹. Also, relative standard deviation (R.S.D.) for the determination of 2 and 50 ng mL⁻¹ of Hg(II) was 5.2 and 4.7% (n = 6), respectively. Due to the quantitative extraction of Hg(II) from 1000 mL of the sample solution an enhancement factor as large as 1230-fold can be obtained. The proposed method has been validated using a certified reference materials, and also the method has been applied successfully for the determination of Hg(II) in aqueous samples.     

Polythiophene-coated Fe3O4 superparamagnetic nanocomposite: Synthesis and application as a new sorbent for solid-phase extraction

In the present work, a novel type of superparamagnetic nanosorbent, polythiophene-coated Fe₃O₄ nanoparticles (Fe₃O₄@PTh NPs), have been successfully synthesized. The synthesized NPs were characterized by scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy, and thermal gravimetric analysis (TGA). The synthesized Fe₃O₄@PTh NPs were applied as an efficient sorbent for extraction and preconcentration of several typical plasticizer compounds (di-n-butyl phthalate (DBP), di-(2-ethylhexyl) phthalate (DEHP), and dioctyl adipate (DOA)) from environmental water samples. Separation of Fe₃O₄@PTh NPs from the aqueous solution was simply achieved by applying external magnetic field. Separation and determination of the extracted plasticizers was performed by gas chromatography–flame ionization detection (GC–FID). Several variables affecting the extraction efficiency of the analytes i.e., amount of NPs sorbent, salt concentration, extraction time, and desorption conditions were investigated and optimized. The best working conditions were as follows: amount of sorbent, 100 mg; NaCl concentration, 30% (w/v); sample volume, 45 mL; extraction time, 10 min; and 100 μL of ethyl acetate for desorption of the analytes within 2 min. Under optimized conditions, preconcentration factors for DBP, DEHP, and DOA were obtained as 86, 194, and 213, respectively. The calibration curves were linear (R² > 0.998) in the concentration range of 0.4–100 μg L⁻¹ for both DEHP and DOA and 0.7–100 μg L⁻¹ for DBP. The limits of detection (LODs) were obtained in the range of 0.2–0.4 μg L⁻¹. The intra-day relative standard deviations (RSDs%) based on four replicates were obtained in the range of 4.0–12.3%. The proposed procedure was applied to analysis of water samples including river water, bottled mineral water, and boiling water exposed to polyethylene container (after cooling) and recoveries between 85 and 99% and RSDs lower than 12.8% were obtained.     

Fabrication of graphene/Fe3O4@polythiophene nanocomposite and its application in the magnetic solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

Polythiophene (PT) was used as a surface modifier of graphene/Fe₃O₄ (G/Fe₃O₄) composite to increase merit of it, and also overcome some limitations and disadvantages of using G/Fe₃O₄ alone as solid phase extraction (SPE) sorbent. An in-situ chemical polymerization method was employed to prepare G/Fe₃O₄@PT nanocomposites. Application of this newly designed material in the magnetic SPE (MSPE) of polycyclic aromatic hydrocarbons (PAHs), as model analytes, in the environmental water samples was investigated. The characterization of the hybrid material was performed using transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray analysis, Fourier transform-infrared (FT-IR) spectroscopy and vibrating sample magnetometry. Seven important parameters, affecting the extraction efficiency of PAHs, including: amount of adsorbent, adsorption and desorption times, type and volume of the eluent solvent, initial sample volume and salt content of the sample were evaluated. The optimum extraction conditions were obtained as: 4 min for extraction time, 20 mg for sorbent amount, 100 mL for initial sample volume, toluene as desorption solvent, 0.6 mL for desorption solvent volume, 6 min for desorption time and 30% (w/v) for NaCl concentration. Good performance data were obtained at the optimized conditions. Detection limits were in the range of 0.009–0.020 μg L⁻¹ in the real matrix. The calibration curves were linear over the concentration ranges from 0.03 to 80 μg L⁻¹ with correlation coefficients (R²) between 0.995 and 0.998 for all the analytes. Relative standard deviations were ranged from 4.3 to 6.3%. Appropriate recovery values, in the range of 83–107%, were also obtained for the real sample analysis.     

Synthesis, structure and magnetic properties of porous magnetic composite, based on MCM-41 molecular sieve with Fe3O4 nanoparticles

Porous magnetic composites were prepared by the synthesis of molecular sieve MCM-41 in the presence of Fe₃O₄ nanoparticles with average diameter of 15 nm. Nanoparticles were captured by porous silica matrix MCM-41, which resulted in their incorporation, as it was confirmed by TEM, SEM and X-ray diffraction. The materials possessed high surface area (392-666 m² g⁻¹), high pore volume (0.39-0.73 cm³ g⁻¹) along with high magnetic response (M_S up to 28.4 emu g⁻¹ at 300 K). Calcination of samples resulted in partial oxidation of Fe₃O₄ to α-Fe₂O₃. The influence of nanoparticles content on sorption and magnetic properties of the composites was shown. No hysteresis was found for the samples at 300 K; at 5 K, H_C was in the range 370-385 G for non-calcinated samples and 350-356 G for calcinated ones.     

Magnetically assisted solid phase extraction using Fe3O4 nanoparticles combined with enhanced spectrofluorimetric detection for aflatoxin M1 determination in milk samples

A novel, facile and inexpensive solid phase extraction (SPE) method using ethylene glycol bis-mercaptoacetate modified 3-(trimethoxysilyl)-1-propanethiol grafted Fe₃O₄ nanoparticles coupled with spectrofluorimetric detection was proposed for determination of aflatoxin M1 (AFM1) in liquid milk samples. The method uses the advantage fluorescence enhancement by β-cyclodexterin complexation of AFM1 in 12% (v/v) acetonitrile–water and the remarkable properties of Fe₃O₄ nanoparticles namely high surface area and strong magnetization were utilized to achieve high enrichment factor (57) and satisfactory extraction recoveries (91–102%) using only 100 mg of magnetic adsorbent. Furthermore, fast separation time of about 15 min avoids many time-consuming column-passing procedures of conventional SPE. The main factors affecting extraction efficiency including pH value, desorption conditions, extraction/desorption time, sample volume, and adsorbent amount were evaluated and optimized. Under the optimal conditions, a wide linear range of 0.04–8 ng mL⁻¹ with a low detection limit of 0.015 ng mL⁻¹ was obtained. The developed method was applied for extraction and preconcentration of AFM1 in three commercially available milk samples and the results were compared with the official AOAC method.     

Evaluation of a magnetic polysulfone microcapsule containing organic modified montmorillonite as a novel solid-phase extraction sorbent with chlorophenols as model compounds

A porous polysulfone microcapsule containing organic modified montmorillonite and magnetic nanoparticles (OMMT-Fe₃O₄@PSF) has been successfully prepared by a phase-inversion method and evaluated as a magnetic solid-phase extraction (MSPE) sorbent for clean-up and enrichment of 4-chlorophenol (4-CP) and 2-chlorophenol (2-CP) in aqueous samples. Compared with a microcapsule containing the conventional extraction sorbent C18 (C18-Fe₃O₄@PSF), OMMT-Fe₃O₄@PSF had much lower cost, a faster adsorption rate, and superior uptake amounts for the investigated analytes. The proposed microcapsule has been developed for the extraction of 4-CP and 2-CP from environmental water samples and their analysis by high-performance liquid chromatography with UV detection (HPLC-UV). Various parameters, such as pH, extraction time, the mass of sorbent, and the desorption conditions, have been evaluated and the calibration curves of the chlorophenols were linear (R² ≥ 0.9985) in the range from 1.01 to 104.5 ng mL⁻¹. The limits of detection at a signal-to-noise (S/N) ratio of 3 were 0.22 and 0.17 ng mL⁻¹ and the limits of quantification calculated at S/N = 10 were 1.52 and 1.07 ng mL⁻¹ for 2-CP and 4-CP, respectively. The recoveries of 2-CP and 4-CP from natural water and the treated wastewater samples were in the range of 84.4-115% with relative standard deviations (RSDs) lower than 7.0%. The results have demonstrated the suitability of the MSPE approach for the analysis of trace chlorophenols in aqueous samples.     

Pseudo-homogeneous immunoextraction of epitestosterone from human urine samples based on gold-coated magnetic nanoparticles

A pseudo-homogeneous immunoextraction method based on gold-coated magnetic nanoparticles (MNPs) for the specific extraction and quantitative analysis of epitestosterone (17α-hydroxy-4-androsten-3-one, abbreviated as “ET”) from human urine samples by high-performance liquid chromatography (HPLC) has been developed. Half-IgG of anti-ET monoclonal antibodies were covalently immobilized onto (Fe₃O₄)_core-Au_shell (Fe₃O₄@Au) MNPs. An external magnetic field was applied to collect the MNPs which were then rinsed with distilled water followed by elution with absolute methanol to obtain ET as the analyte. The obtained extraction solution was analyzed by HPLC with UV detection (244 nm) within 12 min. The standard calibration curve for ET showed good linearity in the range of 20-200 ng mL⁻¹ in phosphate-buffered saline (PBS) solutions with acceptable accuracy and precision. Limit of detection for ET was 0.06 ng mL⁻¹ due to an enrichment factor of 100-fold was achieved. The results obtained by the present method for spiked human urine samples were in agreement with those from indirect competitive enzyme-linked immunoadsorbent assays (ELISAs). The antibody-conjugated Fe₃O₄@Au MNPs are novel materials for immunoaffinity extraction. Compared with the conventional technique using immunoaffinity column, the method described here for sample pretreatment was fast, highly specific, and easy to operate.     

Electrocatalytic oxidation behavior of guanosine at graphene, chitosan and Fe3O4 nanoparticles modified glassy carbon electrode and its determination

A graphene, chitosan and Fe₃O₄ nanoparticles (nano-Fe₃O₄) modified glassy carbon electrode (graphene-chitosan/nano-Fe₃O₄/GCE) was fabricated. The modified electrode was characterized by scanning electron microscope and electrochemical impedance spectroscopy. The electrochemical oxidation behavior of guanosine was investigated in pH 7.0 phosphate buffer solution by cyclic voltammetry and differential pulse voltammetry. The experimental results indicated that the modified electrode exhibited an electrocatalytic and adsorptive activities towards the oxidation of guanosine. The transfer electron number (n), transfer proton number (m) and electrochemically effective surface area (A) were calculated. Under the optimized conditions, the oxidation peak current was proportional to guanosine concentration in the range of 2.0 × 10⁻⁶ to 3.5 × 10⁻⁴ mol L⁻¹ with the correlation coefficient of 0.9939 and the detection limit of 7.5 × 10⁻⁷ mol L⁻¹ (S/N = 3). Moreover, the modified electrode showed good ability to discriminate the electrochemical oxidation response of guanosine, guanine and adenosine. The proposed method was further applied to determine guanosine in spiked urine samples and traditional Chinese medicines with satisfactory results.     

A novel magnetic poly(aniline-naphthylamine)-based nanocomposite for micro solid phase extraction of rhodamine B

A novel Fe₃O₄–poly(aniline-naphthylamine)-based nanocomposite was synthesized by chemical oxidative polymerization process as a magnetic sorbent for micro solid phase extraction. The scanning electron microscopy images of the synthesized nanocomposite revealed that the copolymer posses a porous structure with diameters less than 50 nm. The extraction efficiency of this sorbent was examined by isolation of rhodamine B, a mutagenic and carcinogenic dye, from aquatic media in dispersion mode. Among different synthesized polymers, Fe₃O₄/poly(aniline-naphthylamine) nanocomposite showed a prominent efficiency. Parameters including the desorption solvent, amount of sorbent, desorption time, sample pH, ionic strength, extraction time and stirring rate were optimized. Under the optimum condition, a linear spiked calibration curve in the range of 0.35–5.00 μg L⁻¹ with R² = 0.9991 was obtained. The limits of detection (3S_b) and limits of quantification (10S_b) of the method were 0.10 μg L⁻¹ and 0.35 μg L⁻¹ (n = 3), respectively. The relative standard deviation for water sample with 0.5 μg L⁻¹ of RhB was 4.2% (n = 5) and the absolute recovery was 92%. The method was applied for the determination of rhodamine B in dishwashing foam, dishwashing liquid, shampoo, pencil, matches tips and eye shadows samples and the relative recovery percentage were in the range of 94–99%.     

Microscale solid phase extraction of glyphosate and aminomethylphosphonic acid in water and guava fruit extract using alumina-coated iron oxide nanoparticles followed by capillary electrophoresis and electrochemiluminescence detection

A microscale solid-phase extraction (SPE) method using alumina-coated iron oxide nanoparticles (Fe₃O₄@Al₂O₃ NPs) as the affinity adsorbent for glyphosate (GLY) and its major metabolite aminomethylphosphonic acid (AMPA) in aqueous solution is reported. One milligram of Fe₃O₄@Al₂O₃ NPs was employed to extract both analytes in 5 ml of aqueous solution. After 5 min extraction, magnetic NPs were isolated from sample solution by employing an external magnet. Followed by rinsing the NPs with 5 μl of 20 mM Na₄P₂O₇ solution for 5 min, the extract was directly analyzed using the derivatization-free CE-electrochemiluminescence (CE-ECL) method. With a sample-to-extract volume ratio of 1000, the enrichment factors for GLY and AMPA were 460 and 64, respectively. The limits of detection (LODs) were 0.3 and 30 ng ml⁻¹ for GLY and AMPA in water, respectively. The developed method was applied to the analysis of GLY in guava fruit. The LOD of GLY in guava was 0.01 μg g⁻¹. Total analysis time including sample pretreatment, SPE and CE-ECL was less than 1 h.     

Ultrasensitive fluorometric determination of hydrogen peroxide and glucose by using multiferroic BiFeO3 nanoparticles as a catalyst

BiFeO₃ magnetic nanoparticles (BFO MNPs) are used as a catalyst to develop an ultrasensitive method for the determination of H₂O₂. It is found that BFO MNPs can catalyze the decomposition of H₂O₂ to produce OH radicals, which in turn oxidize the weakly fluorescent benzoic acid to a strongly fluorescent hydroxylated product with a maximum emission at 405 nm. This makes it possible to sensitively quantify traces of H₂O₂. Under optimized conditions, the fluorescence intensity is observed to be well linearly correlated with H₂O₂ concentration from 2.0 × 10⁻⁸ to 2.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 4.5 × 10⁻⁹ mol L⁻¹ (S/N = 3). In addition, a selective method for glucose determination is developed by using both glucose oxidase and BFO MNPs, which has a linear range for glucose concentration from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. These new methods have been successfully applied for the determination of H₂O₂ in rainwater and glucose in human serum samples.     

β−cyclodextrins-based inclusion complexes of CoFe2O4 magnetic nanoparticles as catalyst for the luminol chemiluminescence system and their applications in hydrogen peroxide detection

β−cyclodextrins (β−CD)-based inclusion complexes of CoFe₂O₄ magnetic nanoparticles (MNPs) were prepared and used as catalysts for chemiluminescence (CL) system using the luminol-hydrogen peroxide CL reaction as a model. The as-prepared inclusion complexes were characterized by XRD (X-ray diffraction), TGA (thermal gravimetric analysis) and FT-IR. The oxidation reaction between luminol and hydrogen peroxide in basic media initiated CL. The effect of β−CD-based inclusion complexes of CoFe₂O₄ magnetic nanoparticles and naked CoFe₂O₄ magnetic nanoparticles on the luminol-hydrogen peroxide CL system was investigated. It was found that inclusion complexes between β−CD and CoFe₂O₄ magnetic nanoparticles could greatly enhance the CL of the luminol-hydrogen peroxide system. Investigation on the kinetic curves and the chemiluminescence spectra of the luminol-hydrogen peroxide system demonstrates that addition of CoFe₂O₄ MNPs or inclusion complexes between β−CD and CoFe₂O₄ MNPs does not produce a new luminophor of the chemiluminescent reaction. The luminophor for the CL system was still the excited-state 3-aminophthalate anions (3-APA*). The enhanced CL signals were thus ascribed to the possible catalysis from CoFe₂O₄ MNPs or inclusion complexes between β−CD and CoFe₂O₄ nanoparticles. The feasibility of employing the proposed system for hydrogen peroxide sensing was also investigated. Experimental results showed that the CL emission intensity was linear with hydrogen peroxide concentration in the range of 1.0 × 10⁻⁷ to 4.0 × 10⁻⁶ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁸ mol L⁻¹ under optimized conditions. The proposed method has been used to determine hydrogen peroxide in water samples successfully.     

Preparation of magnetic strong cation exchange resin for the extraction of melamine from egg samples followed by liquid chromatography-tandem mass spectrometry

In the work, magnetic strong cation exchange (MSCX) resins were prepared using hydrophobic Fe₃O₄ magnetite as the magnetically susceptible component, styrene and divinylbenzene as polymeric matrix components, acetyl sulfonate as the sulfonation agent. The resins were successfully applied to the extraction of melamine (MEL) from egg samples. The extraction procedure was carried out in a single step by blending and stirring the sample, extraction solvent and the magnetic resins. The MEL was extracted from the sample matrix then adsorbed onto the resins directly through ion-exchange interaction. When the extraction was completed, the resins with adsorbed analyte were easily separated from the sample matrix by applying an appropriate magnetic field. Main factors affecting the extraction of MEL such as the amount of MSCX resins, extraction time, washing and eluting conditions were optimized. The MEL eluted from the resins was determined by liquid chromatography-tandem mass spectrometry. The linearity of quantification obtained by analyzing matrix-matched standards is in the range of 10-1000 ng g⁻¹. The limit of detection and quantification obtained are 2.6 and 8.8 ng g⁻¹, respectively. The relative standard deviations of intra- and inter-day ranging from 1.6% to 6.5% and from 2.1% to 7.2% are obtained. The recoveries of MEL are in the range of 77.2-99.3%. The proposed method was successfully applied to determine MEL in eggs obtained from different local markets. MEL was detectable with the contents of 43.5 and 234.1 ng g⁻¹ in two samples.