Hollow-fiber membranes coated with polymerizable bicontinuous microemulsions

A new method has been successfully employed to prepare hollow-fiber membranes by coating and polymerizing bicontinuous microemulsions onto the internal surfaces of hollow-fiber membranes. The bicontinuous microemulsion consisting of water, a polymerizable zwitterionic surfactant of acryloyloxyundecyl dimethylammonio acetate, methyl methacrylate, and 2-hydroxylethyl methacrylate (HEMA) can form a transparent polymer thin film after polymerization. The hollow-fiber membranes as the supports for microemulsion coatings were fabricated from the spinning solution of polyethersulfone/diethylene glycol/N-methyl-2-pyrrolidone. The microemulsion coated hollow-fiber membranes were evaluated by the separation efficiency and the permeation rate of polyethylene glycol (PEG) solutions. The performance of coated membrane on the PEG separation is strongly dependent on the concentration of HEMA and water in precursor bicontinuous microemulsions. The pore size of the hollow-fiber membranes can be regulated between about 2 to 40 nm by varying the composition of precursor bicontinuous microemulsions. The characteristics of the coated membranes is believed to be directly related to the bicontinuous structures of precursor bicontinuous microemulsions. The use of polymerizable bicontinuous microemulsions enable one to better control the microstructures of coated membranes via in situ polymerization.     

Structure of biodiesel based bicontinuous microemulsions for environmentally compatible decontamination: A small angle neutron scattering and freeze fracture electron microscopy study

Most toxic industrial chemicals and chemical warfare agents are hydrophobic and can only be solubilized in organic solvents. However, most reagents employed for the degradation of these toxic compounds can only be dissolved in water. Hence, microemulsions are auspicious media for the decontamination of a variety of chemical warfare agents and pesticides. They allow for the solubilization of both the lipophilic toxics and the hydrophilic reagent. Alkyl oligoglucosides and plant derived solvents like rapeseed methyl ester enable the formulation of environmentally compatible bicontinuous microemulsions. In the present article the phase behavior of such a microemulsion is studied and the bicontinuous phase is identified. Small angle neutron scattering (SANS) and freeze fracture electron microscopy (FFEM) measurements are used to characterize the structure of the bicontinuous phase and allow for an estimation of the total internal interface. Moreover, also the influence of the co-surfactant (1-pentanol) on the structural parameters of the bicontinuous phase is studied with SANS.     

Structure of microemulsions with gemini surfactant studied by solvatochromic probe and diffusion NMR

The structure of microemulsions prepared by the anionic gemini surfactant didodecyl diphenyl ether disulfonate (C12-DADS) was investigated by a solvatochromic probe and nuclear magnetic resonance (NMR) diffusion measurements. The NMR measurements indicate the presence of bicontinuous and oil-in-water microemulsions depending on microemulsion composition. The absorbance spectra of the solvatochromic probe, Nile red, indicate the solubilization of the probe in different sites, in agreement with the NMR findings. It was also found that the microemulsions were capable of dissolving the hydrophobic probe, Nile red, up to four times better than expected if it were simply dissolved in the toluene phase.     

Sugar-based microemulsion glass templates

Complex fluids comprising of surfactants with water and/or oil form a rich variety of dynamic self-assembled structures, ranging from spherical swollen micelles, viscous rod-like micelles, and bicontinuous microemulsions to ordered liquid crystalline phases. The wide range of practical and specialized applications of complex fluids has made them the subject of intense research for many decades. Here, we demonstrate for the first time how bicontinuous microemulsions containing equal masses of oil and sugar can be driven to the glassy state without phase separation at ambient temperatures by controlled desiccation of sugar-rich microemulsions. The robust nanostructure of these microemulsion glasses allows polymerization of hydrophobic liquid monomers within the interstices of the glassy microemulsion template without macroscopic phase separation. Yet after polymerization, the sugar and surfactant template can be easily removed by dissolution in water.     

Microstructure and structural transition in microemulsions stabilized by aldonamide-type surfactants

Significant efforts were undertaken to characterize the microstructure and structural properties of water-in-oil (w/o), oil-in-water (o/w), and bicontinuous (bc) microemulsions composed of N-alkyl-N-methylgluconamides (n-alkyl = n-C(12)H(25), n-C(14)H(29), n-C(16)H(33)) and n-alcohols (ethanol, n-propanol, n-butanol) or iso-alcohols (iso-propanol, iso-butanol) as cosurfactants, as well as iso-octane and water. The internal structure of so created four-component system was elucidated by means of an analysis of isotropic area magnitudes in phase diagrams and conductivity measurements. Dynamic light scattering (DLS) measurements provided the microemulsion size and polydispersity. Polarity and viscosity of microemulsion microenvironment were acquired by means of electron paramagnetic resonance (EPR), UV-vis absorption spectroscopy (in the case of w/o droplets), and steady-state fluorescence (SSF) (in the case of o/w droplets). The results show that both the surfactant and the cosurfactant types affect the shape and extent of microemulsions. The size of droplets depends strongly on the type of examined microemulsion and the type of cosurfactant (linear or brunched) but is almost independent of the length of the surfactant alkyl chain. The size of microemulsion droplets ranges from 8.1 to 22.6 nm and from 3.7 to 14.3 nm respectively, for o/w and o/w microemulsions, making them good candidates for both template-based reactions and household components solubilizing media.     

Solubilization of Celecoxib in Microemulsions Based on Mixed Nonionic Surfactants and Peppermint Oil

U-type microemulsions formulated with water, mixed nonionic surfactants, and peppermint oil were used to solubilize celecoxib. Microemulsion dilution and interfacial factors contributing to the celecoxib solubilization were evaluated. Celecoxib solubilization capacity decreases with the increase in the water content. Electrical conductivity, dynamic viscosity, and SAXS measurements reveal the structural transition occurring in the microemulsion region. It was found that below 0.25 aqueous phase volume fraction the water-in-oil microemulsions are present, the transition between the water-in-oil to bicontinuous and then to oil-in water microemulsions occur at 0.30 and 0.8 aqueous phase volume fraction, respectively. The results demonstrate that the solubilized drug affects the transition from bicontinuous to water-in-oil microemulsions. The solubilized drug increases the hydrodynamic radius of the oil-in-water microemulsion droplets measured by dynamic light scattering.     

Gelled polymerizable microemulsions. 2. Microstructure

Using bicontinuous microemulsions as templates opens a new field for the design of novel structures and thus novel materials, but has significant challenges due to the very small composition and temperature windows in which microemulsions are bicontinuous. In previous work we had shown that we can take a ternary base system (water-n-dodecane--C 13/15E 5), add monomer and cross-linker ( N-isopropylacrylamide and N, N'-methylenebisacrylamide) to the water phase, and add a gelator (12-hydroxyoctadecanoic acid) to the oil phase while remaining in the one-phase region of the phase diagram. It was also possible to allow the gelator to form an organogel by changing the temperature such that we crossed the sol--gel line, which fell within the one-phase region. In this work, we show conclusively that addition of the monomers and the gelator does not affect the microemulsion microstructure and that, even in the gelled state, the polymerizable microemulsion is indeed bicontinuous. 1H NMR self-diffusion, conductivity, and small-angle neutron scattering measurements all confirm the bicontinuous nature of the gelled polymerizable microemulsion.     

Polymerisation of vinyl acetate in microemulsions with methanol

 The homogeneity domains for the system vinyl acetate – methanol – monomaleate of nonylphenol ethoxylated with 25 mol ethylene oxide as an aqueous solution (MEMNPEO25) (33%) have been studied; it has been shown that, due to the shorter chain of methanol, these domains are more reduced than in the case of ethanol. The changes in refractive indexes and electrical conductivities have shown the formation of microemulsions with different structures (water-in-oil, bicontinuous or oil-in-water). Ammonium persulphate is soluble only in oil-in-water or in bicontinuous microemulsions. The initial polymerisation rates as well as the decomposition rates for the initiator are apparently affected when the microemulsion structure is modified. The polymerisation rate of vinyl acetate is higher in the presence of methanol than in the presence of ethanol for similar compositions; this fact may be attributed to a higher degree of ionisation of the initiator in the presence of methanol. Also, in polymerisations initiated by benzoyl peroxide, the conversions are influenced by the microstructure; thus, the maximum corresponds to water-in-oil microemulsions. By measuring the amount of unreacted MEMNPEO25 (gel permeation chromatography) we were able to show that the copolymer formed consisted of vinyl acetate and reactive surfactant. Received: 9 March 1999/Accepted: 13 March 2000     

The effect of structure of oil phase, surfactant and co-surfactant on the physicochemical and electrochemical properties of bicontinuous microemulsion

Efforts were made to prepare bicontinuous microemulsions with ten different oil phases involving aliphatic, linear, and aromatic hydrocarbons as oil phases, two co-surfactants (n-butanol and n-pentanol) and two surfactants: cationic (CTAB) and anionic (SDS). Different weight percentages were employed for the preparation of cationic and anionic surfactant based microemulsions as reported in the literature. Out of the 40 compositions (10 oil phasesx2 co-surfactantsx2 surfactants) thus selected only 28 systems showed stable bicontinuous microemulsion phase. This behavior is explained on the basis of the structures of various constituents present in the microemulsions. Viscosity variations of stable bicontinuous microemulsions are found to depend mainly on the nature of co-surfactant. Conductivity behavior on the other hand depends mainly on the weight percentage and composition of aqueous phase. The solubility of pyrene in the oil phase determines the excimer formation and fluorescence behavior in microemulsions. The electron transfer property of both the water-soluble and the oil-soluble redox systems does not depend on the oil phase and the co-surfactant. The significance and importance of characterizing well defined bicontinuous microemulsions is thus highlighted.     

Microstructure and structural transition in palm-kernel oil microemulsion using 1.5-order differential electroanalysis

The microemulsification in palm-kernel oil/cetyltrimethylammonium bromide/iso-pentanol/water system is investigated. The effect of iso-pentanol concentration in microemulsions on the size of single-phase microemulsion region is also discussed. It is found that the maximum microemulsion domain is obtained when iso-pentanol-to-cetyltrimethylammonium bromide mass ratio is 1.75. The diffusion coefficients of electroactive probe (ferrocene) in microemulsion microenvironment are measured by 1.5-order differential electroanalysis. The microstructure and structural transition from water-in-oil to oil-in-water microemulsions through a bicontinuous structure is examined. The results are found to be in agreement with that of conductivity measurements.     

Microemulsion polymerization of acrylamide and styrene: Effect of the structures of reaction media

Isothermal phase diagrams of the system cetyltrimethylammonium bromide (CTAB)/n‐butanol/n‐octane/water were constructed, and the effect of the oil (n‐octane) contents on the microemulsions was studied at 40 °C. We determined the microemulsion structures of two systems, CTAB/n‐butanol/10% n‐octane/water and sodium dodecyl sulfonate (As)/n‐butanol/20% styrene/water, by conductivity measurements to investigate the polymerization of acrylamide and styrene in the two microemulsion systems. The polymerization kinetics of the water‐soluble monomer acrylamide in CTAB micelles and the different CTAB/n‐butanol/10% n‐octane/water microemulsion media [water‐in‐oil (W/O), bicontinuous (BC), and oil‐in‐water (O/W)] were studied with water‐soluble sodium bisulfite as the initiator. The maximum polymerization rate in CTAB micelles was found at the second critical micelle concentration. A mechanism of polyacrylamide formation and growth was proposed. A connection between the structures of the microemulsions and the polymerization rates was observed; the maximum polymerization rate occurred at two transition points, from W/O to BC and from BC to O/W, and the polyacrylamide molecular weights, which depended on the structures of the microemulsions, were also found. A square‐root dependence of the polymerization rates on the initiator concentrations was obtained in CTAB micelles and O/W microemulsion media. The polymerization of the oil‐soluble monomer styrene in different As/n‐butanol/20% styrene/water microemulsion media (W/O, BC, and O/W) was also investigated with different initiators: water‐soluble potassium persulfate and oil‐soluble azobisisobutyronitrile. A similar connection between the structures of the microemulsions and the conversions of styrene in CTAB/n‐butanol/10% n‐octane/water for the polymerization of acrylamide was observed again. The structures of the microemulsions had an important role in the molecular weights and sizes of polystyrene. The polystyrene particles were 10–20 nm in diameter in BC microemulsion media and 30–60 nm in diameter in O/W microemulsion media according to transmission electron microscopy. We determined the solubilization site of styrene in O/W microemulsion drops by ¹H NMR spectra to analyze the results of the microemulsion polymerization of styrene. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3320–3334, 2001     

Surfactant-free Ionic Liquid Microemulsions of N,N-dimethylformamide, 1-butyl-3-methylimidazolium hexafluorophosphate,and toluene

The phase diagram of a ternary system consisting of the hydrophobic ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF₆), N, N-dimethylformamide (DMF), and toluene was prepared at 25°C. A single-phase microemulsion and a multiphase region were demonstrated. The systems were nonaqueous IL microemulsions in the absence of traditional surfactants. The single-phase region could be divided into toluene-in-bmimPF₆, bicontinuous, and bmimPF₆-in-toluene subregions by electrical conductivity, similar to the case of surfactant-based IL microemulsions. And by the use of methyl orange as an absorption probe, the polarity of the bmimPF₆-in-toluene microemulsion was probed by UV–vis spectroscopy. The polarity of bmimPF₆ domains increased with increasing bmimPF₆ constant, and a relatively constant polarity was obtained when bmimPF₆ was increased to a certain extent.     

Lipase-catalyzed enantioselective esterifications using different microemulsion-based gels

Chiral esters with high optical purity have been synthesized at 298.2 K from racemic 2-octanol and alkanoic acids using the commerical lipases fromChromobacterium viscosum (CV) orCandida sp. (SP 525) immobilized in microemulsion-based gelatin gels. The microemulsions consisted of water and alkanes stabilized by the anionic surfactant sodium 1,4-bis(2-ethylhexyl) sulfosuccinate (AOT) and the naturally occurring zwitterionic surfactant soybean lecithin, respectively. The enzymes were solubilized both in water-in-oil (W/O) microemulsions and in microemulsions with a bicontinuous structure. Different microstructures of the gels were chosen since the enzyme may undergo conformational changes in different environments resulting in different catalytic efficiencies toward competing substrates. Therefore, it is of great fundamental interest to know the phase behaviour and the microstructures of the used microemulsion systems. Phase diagrams were determined at 298.2 K for the systems water-hexane-AOT and ethanol/water (11)-hexadecane-soybean lecithin. The former system exhibited a large one-phase W/O microemulsion region, while in the latter a small one-phase region with bicontinuous structure was present. The kinetic enantiomeric ratios (E-values), as determined from enantiomeric excess (e.e.) values at a conversion below 0.5, were higher both in the W/O microemulsion as well as in the bicontinuous microemulsion using the SP 525 lipase, than using the CV lipase. On the other hand, the conversions were higher using gels based on W/O microemulsions (AOT stabilized) than using gels based on microemulsions with a bicontinuous structure (lecithin stabilized).     

The influence of structure and composition of a reverse SDS microemulsion on enzymatic activities and electrical conductivities

The activity of the enzyme horse radish peroxidase (HRP) is studied in a series of reverse microemulsions composed of dodecane, aqueous buffer, sodium dodecylsufate (SDS) and alcohols of the homologous series 1-butanol to 1-octanol. The HRP catalyzed reaction is the oxidation of a classical water soluble substrate, the 2,2-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt (ABTS) by hydrogen peroxide. In parallel electrical conductivity measurements are performed on the same solutions. The structural changes in the microemulsions, as inferred by the conductivity measurements, correlate remarkably well with the changes in the enzymatic activities. In particular it is found that (a) the maximum activity of the enzyme is always related to its optimum hydration and that this hydration can be related to the microemulsion structures, (b) the enzyme inhibition caused by the alcohols in microemulsions is a consequence of both the solubility of the alcohols in the buffer and the rigidity of the interfacial film. Consequently, it can be concluded that enzymatic activity measurements are a valuable tool to study confined systems such as microemulsions and, in particular, the amount of available hydration water. Enzymatic activities can be finely tuned by small changes in microemulsion structures, probably in a predictive way.     

微乳液聚合制备透明丙烯酸酯多孔共聚物

多孔聚丙烯酸酯;引发;微乳液聚合制备透明丙烯酸酯多孔共聚物     

微乳液结构的研究

测定了十二烷基磺酸钠／正丁醇／２０％苯乙烯／水体系的相平衡，用冷冻刻蚀、ＥＳＲ、ＦＴ－ＩＲ研究了上述体系微乳液的结构，研究表明，苯乙烯含量恒定时，随着体系中水含量增加，电导确定的双连续结构的微乳液经历着从油包水到以连续再到水包油变化，ＦＴ－ＩＲ测定表明，Ｗ／Ｏ微乳兴较Ｏ／Ｗ微乳液的ＯＨ伸缩振动和弯曲振动频率有显著减小，说明Ｗ／Ｏ微乳兴中氢键缔合要比Ｏ／Ｗ强得多。ＥＳＲ测定表明Ｏ／Ｗ微乳液的旋转相关     

丙烯酸酯及苯乙烯微乳体系的相行为及微乳聚合

甲基丙烯酸甲酯;十二烷基磺酸钠;十二烷基磺酸钠;丙烯酸酯及苯乙烯微乳体系的相行为及微乳聚合     

Probing the microstructure of nonionic microemulsions with ethyl oleate by viscosity, ROESY, DLS, SANS, and cyclic voltammetry

Microemulsions are important formulations in cosmetics and pharmaceutics and one peculiarity lies in the so-called "phase inversion" that takes place at a given water-to-oil concentration ratio and where the average curvature of the surfactant film is zero. In that context, we investigated the structural transitions occurring in Brij 96-based microemulsions with the cosmetic oil ethyl oleate and studied the influence of the short chain alcohol butanol on their structure and properties as a function of water addition. The characterization has been carried out by means of transport properties, spectroscopy, DLS, SANS, and electrochemical methods. The results confirm that the nonionic Brij 96 in combination with butanol as cosurfactant forms a U-type microemulsion that upon addition of water undergoes a continuous transition from swollen reverse micelles to oil-in-water (O/W) microemulsion via a bicontinuous region. After determining the structural transition through viscosity and surface tension, the 2D-ROESY studies give an insight into the microstructure, i.e., the oil component ethyl oleate mainly is located at the hydrophobic tails of surfactant while butanol molecules reside preferentially in the interface. SANS experiments show a continuous increase of the size of the structural units with increasing water content. The DLS results are more complex and show the presence of two relaxation modes in these microemulsions for low water content and a single diffusive mode only for the O/W microemulsion droplets. The fast relaxation reflects the size of the structural units while the slower one is attributed to the formation of a network of percolated microemulsion aggregates. Electrochemical studies using ferrocene have been carried out and successfully elucidated the structural transformations with the help of diffusion coefficients. An unusual behavior of ferrocene has been observed in the present microheterogeneous medium, giving a deeper insight into ferrocene electrochemistry. NMR-ROESY experiments give information regarding the internal organization of the microemulsion droplets. In general, one finds a continuous structural transition from a W/O over a bicontinuous to an O/W microemulsion, however with a peculiar network formation over an extended concentration range, which is attributed to the somewhat amphiphilic oil ethyl oleate. The detailed knowledge of the structural behavior of this type of system might be important for their future applications.     

Phase behavior, microstructure transition, and antiradical activity of sucrose laurate/propylene glycol/the essential oil of Melaleuca alternifolia/water microemulsions

Nonionic sucrose ester microemulsions composed of sucrose laurate (SL), propylene glycol (PG) and water were prepared with the essential oil of Melaleuca alternifolia, commonly known as tea tree oil (TTO), as oil phase to investigate the phase behavior, microstructure, and antiradical activity. The pseudo-ternary phase diagrams were constructed to elucidate the phase behavior of the microemulsion formations at different weight ratios of surfactant and cosurfactant (S_m = SL/PG) of 1:1, 2:1, and 3:1. The extension of the microemulsion zone was found to be strongly dependent on the S_m ratios. The single phase microemulsion domain, especially o/w microemulsion region increased when S_m ratio is increased from 1:1 to 3:1 and no liquid crystalline structure was observed for all formulations studied. Microstructural aspects were studied by electrical conductivity and pulsed gradient spin echo (PGSE) NMR measurements along water titration line L28 (R_o = 2:8). The results from these combined techniques were in good agreement in regard to the microstructure transition points. The microstructural inversion of w/o to bicontinuous microemulsions occurred at 30 wt.% water while the transition from bicontinuous to o/w structure occurred at 55 wt.% water. The physical stability on storage temperature and time was examined by dynamic light scattering after the centrifuge test and freeze–thaw cycles. The droplet size was kept almost the same without any phase separation, providing less temperature-sensitivity up to 70 °C and good stability for 3 months at room temperature. The chemical profile and radical scavenging activity of TTO in o/w microemulsions was evaluated by means of gas chromatography–mass spectroscopy (GC–MS) and 2,2′-diphenyl-1-picrylhydrazyl free radical (DPPH) scavenging method, respectively. The major abundant constituents of crude TTO, monoterpene alcohols (terpinen-4-ol (41.65%), α-terpineol (3.18%)) and hydrocarbons (γ-terpinene (22.95%), α-terpinene (10.16%)) were identified and the composition percentage of each constituent was calculated form the GC peak areas by normalization method. The DPPH scavenging activity of TTO microemulsion was lower than pure TTO because the SL surfactant may obstruct the interaction between the TTO and DPPH, reducing the number of effective collisions.     

Efficient topical delivery of chlorogenic acid by an oil-in-water microemulsion to protect skin against UV-induced damage

We examined the intradermal delivery of a hydrophilic polyphenol chlorogenic acid by in vitro study using excised guinea pig dorsal skin and Yucatan micropig skin. Skin accumulation as well as the solubility of chlorogenic acid in aqueous vehicles was much greater than for other polyphenols such as quercetin and genistein. However, since enhancement of skin delivery seemed to be necessary to exhibit its protective effects against oxidative damage of skin, we examined the effects of microemulsions as vehicles. Using microemulsions consisting of 150 mM NaCl solution, isopropyl myristate, polyoxyethylene sorbitan monooleate (Tween 80) and ethanol, skin accumulation as well as solubility of chlorogenic acid further increased. Enhancement effect of an oil-in-water (o/w-type) microemulsion was greater than that of a water-in-oil (w/o-type) microemulsion possibly due to the greater increase in solubility. This finding was quite different from previous findings on relatively hydrophobic polyphenols such as quercetin and genistein. Pretreatment of guinea pig dorsal skin with chlorogenic acid containing microemulsion gel prevented erythema formation induced by UV irradiation. These findings indicate the potential use of hydrophilic chlorogenic acid with o/w-type microemulsion as a vehicle to protect skin against UV-induced oxidative damage.