Determination of mercury in the presence of chloride by means of the ternary complex Hg(II)/xylenol orange/amberlite La-2 in non-aqueous media

The system Hg(II)/Xylenol Orange/Amberlite LA-2 dissolved in 1:1 v v 3-methylbutan-1-ol/chloroform medium has been studied. A 3:2:2 complex is formed, which is suitable for analytical measurements at temperatures <18 degrees . This complex allows the determination of mercury in the range 0.19-5.5 ppm with a molar absorptivity of 2.12 x 10(4).mole(-1).cm(-1) at 600 nm and extraction pH of 7.4 (standard deviation 0.065 ppm). The proposed method has been applied to the determination of mercury in contaminated water with a high chloride content.     

On-line preconcentration of mercury by sorption on an anion-exchange resin loaded with 1,5-bis[(2-pyridyl)-3-sulphophenyl methylene] thiocarbonohydrazide and determination by cold-vapour inductively coupled plasma atomic emission

1,5-Bis[(2-pyridyl)-3-sulphophenyl methylene] thiocarbonohydrazide (PSTH) immobilized on an anion-exchange resin (Dowex) has been used for the on-line preconcentration of mercury from biological samples and waters prior to its determination by inductively coupled plasma atomic emission spectroscopy. The metal was eluted from the column using a solution of 2 M HNO(3) and mixed on-line with SnCl(2). The optimum experimental conditions were evaluated for the continuous preconcentration of Hg, the direct generation of mercury vapour and the final determination of this element by ICP-AES. The enrichment, together with low blank levels of the optimized procedure, allow the simple determination of this toxic element at concentrations down to a few nanograms per milliliter. The proposed method has a linear calibration range 5-1000 ng ml(-1) of mercury, with a detection limit of 4 ng ml(-1) (S/N=3) and a sampling rate of 40 h(-1), investigated with a 9 ml sample volume. The precision of the method (evaluated as the relative standard deviation obtained after analyzing ten series of ten replicates) was +/-3.6% at the 10 ng ml(-1) level of Hg(II) and +/-1.3% at the 100 ng ml(-1) level. The accuracy of the method was examined by the analysis of certified reference materials.     

Spectrophotometric determination of mercury with 5-(6-methyl-2-pyridyl)methylene-2-thiohydantoin

A method is described for the direct spectrophotometric determination of mercury(II) with 5-(6-methyl-2-pyridyl)methylene-2-thiohydantoin. The influence of the different experimental parameters on the formation of the complex were studied and optimum conditions for the determination of mercury were established. The precision of the procedure, expressed in terms of relative standard deviation, was 0.2%. Two different complexes (1:2 and 1:1 cation-reagent stoichiometries) have been detected. The method has been tested on copper amalgam for dental use.     

Anodic stripping voltammetric determination of mercury by use of a sodium montmorillonite-modified carbon-paste electrode

A sodium montmorillonite (SWy-2)-modified carbon-paste electrode has been examined for determination of trace levels of mercury. Because of its strong cation-exchange and adsorptive characteristics, SWy-2 greatly improves the sensitivity of determination of Hg(2+). Hg(2+) is preconcentrated and reduced on the modified electrode surface at -0.40 V and then stripped from the electrode surface during the positive potential sweep. The conditions used for determination, e.g. supporting electrolyte, pH, amount of SWy-2, accumulation potential, and accumulation time, were optimized. The peak current was linearly dependent on the concentration of mercury from 1 x 10(-9) to 5 x 10(-7) mol L(-1). The detection limit (signal-to-noise ratio=3) was 1 x 10(-10) mol L(-1) after accumulation for 6 min. When the SWy-2-modified carbon-paste electrode was used to detect mercury in water samples the average recovery was 101.11%.     

Kinetic and equilibrium studies on mercury(II)-coproporphyrin-I. Metal ion exchange reaction with cobalt(II) and application to determination of trace mercury(II)

The reaction of 3,8,13,18-tetramethyl-21H,23H-porphine-2,7,12,17-tetrapropionic acid or coproporphyrin-I (CPI) with mercury(II) was studied spectrophotometrically, and kinetic and equilibrium constants were determined; the influence of temperature on the reaction rate was also studied. It was verified that mercury(II) accelerates the incorporation reaction of cobalt(II) into CPI; the kinetics and mechanism of this reaction at high alkaline pH were studied. Sensitive kinetic methods for the determination of mercury(II) at ppb levels have been established; the apparent molar absorbivity and Sandell's sensitivity for the recommended procedure, at 368 nm, and 400 s after the start of the reaction, were: 4.23x10(5) (l mol(-1)cm(-1)) and 0.474 (ng cm(-2)) (for A=0.001).     

Highly sensitive spectrofluorometric determination of trace amounts of mercury with a new fluorescent reagent, 2-hydroxy-1-naphthaldehydene-8-aminoquinoline.

A new fluorescent reagent, 2-hydroxy-1-naphthaldehydene-8-aminoquinoline (HNAAQ), was synthesized. The fluorescent reaction of this reagent with mercury was also studied. Based on this chelation, a highly sensitive spectrofluorometric method was developed for the determination of trace amounts of mercury in a water-ethanol (5 + 1, v/v) medium at pH 8.0. Under these conditions, the Hg-HNAAQ complex has excitation and emission maxima at 406 and 445 nm, respectively. The linear range of the method is from 0 to 16 microg L(-1) and the detection limit is 0.056 microg L(-1) of mercury. The interference of other ions was studied. In order to enhance the selectivity in the determination of mercury by the present method, we also applied the separation of mercury by distillation. Thus, the selectivity of the method could be increased remarkably. The procedure can be easily performed, and affords good precision and accuracy. This method has been successfully applied to the determination of mercury in waste water and prawns.     

1-(4-nitrophenyl)-3-(2-quinolyl) triazene as an extremely sensitive reagent for spectrophotometric determination of mercury

1-(4-Nitrophenyl)-3-(2-quinolyl)triazene has been synthesized, and used as an extremely sensitive reagent for the spectrophotometric determination of mercury by the decrease in the absorbance of the reagent at 490 nm and pH 9.0-10.8 in the presence of cetylpyridinium bromide. Beer's law is obeyed over the range 0-120 ng/ml Hg(II), the apparent molar absorptivity being 1.0 x 10(6) l.mole(-1).cm(-1). The effect of 69 ionic species or compounds has been examined. Trace mercury in waste water has been determined satisfactorily.     

PAN-6S作络合指示剂连续滴定测定汞和铅的研究

试验研究了pH3.0和pH5.4的介质中,以1 (2 吡啶偶氮) 2 萘酚 6 磺酸(PAN 6S)作为指示剂,以EDTA为滴定剂连续滴定汞和铅,其终点颜色变化敏锐,准确度高。     

Determination of palladium(II) with alpha-(2-benzimidazolyl)-alpha',alpha'-(N-5-nitro-2-pyridylhydrazone)-toluene by adsorptive cathodic stripping voltammetry

The determination of palladium(II) complexed with alpha-(2-benzimidazolyl)-alpha',alpha'-(N-5-nitro-2-pyridylhydrazone)-Toluene (BINPHT) was investigated by adsorptive cathodic stripping voltammetry using hanging mercury drop electrode. Palladium(II) in the sample solution can be determined in BINPHT and ethylenediaminetetraacetic acid (EDTA). Accumulation is achieved by adsorption of Pd(II)-BINPHT complex on a hanging mercury drop electrode. Optimal conditions were found to be: supporting electrolyte; 0.01 M sodium acetate buffer at pH 5.0, accumulation potential; -590 mV versus Ag/AgCl, accumulation time; 180 s, scan rate; 50 mV s(-1), concentration of BINPHT; 2x10(-5) M. The linear range of Pd(II) was observed over the concentration range 20-100 ng ml(-1) The detection limit (S/N=3) is 2 ng ml(-1). A good reproductivity shows RSD of 2.0% (n=7). This procedure offers high selectivity with the presence of EDTA masking some metallic ions. River water sample spiking with palladium was determined.     

Spectrophotometric studies on the simultaneous determination of cadmium and mercury with 4-(2-pyridylazo)-resorcinol

A new method for direct spectrophotometric determination of cadmium with 4-(2-pyridylazo)-resorcinol is reported. Absorption maximum, molar absorptivity and Sandell's sensitivity of the 1:1 (M:L) complex are 510 nm, 2.5 x 10(5) l mol(-1) cm(-1) and 3.55 ng cm(-2), respectively. A linear calibration graph is obtained up to 4.49 microg ml(-1). The zero-crossing measurement technique is found suitable for the direct measurement of the first-derivative value at the specified wavelengths. Cadmium(II) (0.42-9.2 microg ml(-1)) and mercury(II) (0.35-7.4 microg ml(-1)) in different ratios have been determined simultaneously. A critical evaluation of the proposed method is performed by statistical analysis of the experimental data. The developed method was applied to the simultaneous spectrophotometric determination of Cd and Hg in some synthetic mixtures and was found to give satisfactory results.     

Spectrophotometric determination of mercury in soils with triphenyltetrazolium chloride

The formation of the acidocomplex of mercury(II) with triphenyl-tetrazolium chloride is studied spectrophotometrically in water-organic media. The composition of the complex is established as TTC:Hg:I = 1:1:1. The molar absorptivity (255) = (6.45 +/- 0.12) x 10(4) 1 mole(-1). cm(-1) is determined. The selectivity of the reaction is studied and the method for determination of mercury(II) 0.1-0.8 mug/ml is shown. Extraction investigations of the system discussed were carried out. The characteristic values for the extraction equilibrium and the equilibrium in the aqueous phase was determined: extraction constant K(ex) = 3.16 x 10(4), distribution constant K(D) = 20.67, and association constant = 1.53 x 10(3). 5 A rapid and sensitive extractive-photometric method for determination of mercury(II) in soil was developed. The determination was carried out without preliminary elimination of mercury.     

Cloud point extraction of mercury with PONPE 7.5 prior to its determination in biological samples by ETAAS

Cloud point extraction (CPE) has been used for the pre-concentration of mercury, after the formation of a complex with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP), and later analysis by electrothermal atomic absorption spectrometry (ETAAS) using polyethyleneglycolmono-p-nonyphenylether (PONPE 7.5) as surfactant. The chemical variables affecting the separation step were optimized. Under the optimum conditions, i.e, pH 8.5, cloud point temperature 80 degrees C, 5-Br-PADAP=4x10(-5) mol L(-1), PONPE 7.5=0.2%, sample volume=1.0 mL, an enhancement factor of 22-fold was reached. The lower limit of detection (LOD) obtained under the optimal conditions was 0.01 microg L(-1). The precision for 10 replicate determinations at 2.0 microg L(-1) Hg was 4.0% relative standard deviation (R.S.D.). The calibration graph using the pre-concentration system for mercury was linear with a correlation coefficient of 0.9994 at levels near the detection limits up to at least 16 microg L(-1). The method was successfully applied to the determination of mercury in biological samples and in certified reference material (QC METAL LL3).     

Spectrophotometric determination of mercury in environmental sample and fungicides based on its complex with o-carboxy phenyl diazoamino p-azobenzene

In the present method a new reagent o-carboxyphenyl diazoamino p-azobenzene has been synthesised for the determination of mercury spectrophotometrically. The method is based on the reaction of mercury with the reagent in alkaline medium where the reagent is in the aci-form. The purple violet coloured dye-mercury complex showed an absorption maxima at 540 nm. Beer's law is valid over the concentration range of mercury from 0.08 to 0.8 mug ml(-1) (0.08-0.8 ppm). The molar absorptivity and Sandell's sensitivity were found to be 2.22x10(5) mol(-1) cm(-1) and 0.0009 mug cm(-2), respectively. The method has been successfully applied to the determination of mercury in air, water, soil and fungicide samples.     

A sequential injection cold-vapor atomic absorption method for the determination of total mercury

A sequential injection (SI) method for the determination of mercury via cold vapor atomic absorption spectrophotometry is presented. The method differs from flow injection (FI) cold vapor methods for the determination of mercury because of the simplicity of the system required for the method: one pump, one valve, a gas-liquid separator, and an atomic absorption spectrophotometer equipped with a quartz cell. Under optimal conditions, the method has the following figures of merit: a linear calibration range of 1.0 to 20 microg L(-1); a detection limit of 0.46 microg L(-1); and a precision of 0.90% RSD (8 microg L(-1)). The procedure allows for a sampling rate of one injection per 80 s (excluding sample pretreatment). Results from the determination of mercury in water and fish specimens are also presented. The figures of merit of the method are compared to two other SI methods for the determination of mercury.     

Determination of very low levels of dissolved mercury(II) and methylmercury in river waters by continuous flow with on-line UV decomposition and cold-vapor atomic fluorescence spectrometry after pre-concentration on a silica gel-2-mercaptobenzimidazol sorbent

A new, simple and sensitive method for the simultaneous determination of mercury(II) and methylmercury chloride at sub-ng l⁻¹ levels in river waters is described. Inorganic and organic mercury were preconcentrated from fresh water samples simultaneously on a laboratory-made column containing 2-mercaptobenzimidazol loaded on silica gel and then quantitatively eluted with 0.05 M KCN solution and 2.0 M HCl to desorp inorganic and methylmercury species, respectively. After irradiation with an intensive UV source, MeHg⁺ was decomposed and mercury vapours were generated from inorganic and organic mercury using an acidic SnCl₂ solution in a continuous flow system and were subsequently determined with a cold vapour atomic fluorescence (CV-AFS) spectrometer. Detection limits (3σ) were 0.07 and 0.05 ng l⁻¹ (as Hg) for mercury(II) chloride and methylmercury chloride, respectively. Relative standard deviations of method (%R.S.D.) were 8.8 and 10 for inorganic and organomercuric species in the river water, respectively. The analysis of real samples, taken from different rivers, showed that inorganic mercury levels ranged from 4.0±0.6 to 12±1 ng l⁻¹ (as Hg and 95% confidence limit) and methylmercury levels at 0.2±0.02 ng l⁻¹(as Hg).     

Preparation of a clay-modified carbon paste electrode based on 2-thiazoline-2-thiol-hexadecylammonium sorption for the sensitive determination of mercury.

A montmorillonite from Wyoming-USA was used to prepare an organo-clay complex, named 2-thiazoline-2-thiol-hexadecyltrimethylammonium-clay (TZT-HDTA-clay), for the purpose of the selective adsorption of the heavy metals ions and possible use as a chemically modified carbon paste electrode (CMCPE). Adsorption isotherms of Hg2+, Pb2+, Cd2+, Cu2+, and Zn2+ from aqueous solutions as a function of the pH were studied at 298 K. Conditions for quantitative retention and elution were established for each metal by batch and column methods. The organo-clay complex was very selective to Hg(II) in aqueous solution in which other metals and ions were also present. The accumulation voltammetry of Hg(II) was studied at a carbon paste electrode chemically modified with this material. The mercury response was evaluated with respect to the pH, electrode composition, preconcentration time, mercury concentration, "cleaning" solution, possible interferences and other variables. A carbon paste electrode modified by TZT-HDTA-clay showed two peaks: one cathodic peak at about 0.0 V and an anodic peak at 0.25 V, scanning the potential from -0.2 to 0.8 V (0.05 M KNO3 vs. Ag/AgCl). The anodic peak at 0.25 V presents excellent selectivity for Hg(II) ions in the presence of foreign ions. The detection limit was estimated as 0.1 microg L(-1). The precision of determination was satisfactory for the respective concentration level.     

A simple spectrophotometric determination of trace level mercury using 1,5-diphenylthiocarbazone solubilized in micelle.

A very simple, ultra-sensitive and fairly selective non-extractive spectrophotmetric method is presented for the rapid determination of mercury(II) at ultra-trace level using 1,5-diphenylthiocarbazone (dithizone) as a new micellar spectrophotometric reagent (lambdamax = 490 nm) in a slightly acidic (0.07 - 0.17 M H2SO4) aqueous solution. The presence of a micellar system avoids the previous steps of solvent extraction and reduces the cost, toxicity while enhancing the sensitivity, selectivity and the molar absorptivity. The reaction is instantaneous and the absorbance remains stable for over 24 h. The average molar absorption coefficient and Sandell's sensitivity were found to be 5.02 x 10(4) L mol(-1) cm(-1) and 10 ng cm(-2) of Hg, respectively. Linear calibration graphs were obtained for 0.05 - 10 mg L(-1) of Hg; the stoichiometric composition of the chelate is 1:2 (Hg:dithizone). The method is characterized by a detection limit of 1 microg L(-1) of Hg. Large excesses of over 60 cations, anions and complexing agents (e.g. EDTA, tartrate, oxalate, citrate, phosphate, thiourea, azide, SCN-) do not interfere in the determination. The method was successfully applied to a number of environmental water samples (potable and polluted), biological samples (human blood and urine; milk and fish) and soils; solutions contained both mercury(I) and mercury(II) as well as complex synthetic mixtures. The method has high precision and accuracy (s = +/-0.01 for 0.1 mg L(-1)).     

Liquid chromatographic determination of cobalt(II), copper(II) and iron(II) using 2-thiophenaldehyde-4-phenyl-3-thiosemicarbazone as derivatizing reagent

The complexing reagent 2-thiophenaldehyde-4-phenyl-3-thiosemicarbazone (TAPT) was examined for high performance liquid chromatographic (HPLC) separations of cobalt(II), copper(II) and iron(II) or cobalt(II), nickel(II), iron(II), copper(II) and mercury(II) as metal chelates on a Microsorb C-18, 5-mum column (150x4.6 mm i.d.) (Rainin Instruments Woburn, MA, USA). The complexes were eluted isocratically with methanol:acetonitrile:water containing sodium acetate and tetrabutyl ammonium bromide (TBA). UV detection was at 254 nm. The solvent extraction procedure was developed for simultaneous determination of the metals, with detection limits within 0.5-2.5 mug ml(-1) in the final solution. The method was applied for the determination of copper, cobalt and iron in pharmaceutical preparation.     

Mercury speciation by HPLC-cold-vapour radiofrequency glow-discharge optical-emission spectrometry with on-line microwave oxidation

Hollow-cathode (HC) radiofrequency glow-discharge (rf-GD) optical-emission spectrometry (OES) has been used as detector for the determination of inorganic mercury by cold-vapour (CV) generation in a flow-injection (FI) system. Both NaBH4 and SnCl2 were evaluated as reducing reagents for production of mercury CV. The conditions governing the discharge (pressure, He flow rate, and delivered power) and Hg CV generation (NaBH4 or SnCl2 concentration and reagent flow rate) were optimized using both reducing agents. The analytical performance characteristics of FI-CV-rf-GD-OES for mercury detection were evaluated at the 253.6 nm emission mercury line. Detection limits (DL) of 0.2 ng mL(-1) using SnCl2 and 1.8 ng mL(-1) using NaBH4 were obtained (100 microliter sample injections were used). When the optimized experimental conditions using SnCl2 had been determined, the analytical potential of this CV-rf-GD-OES method was investigated as on-line detector for high-performance liquid chromatographic (HPLC) speciation of mercury (Hg(II) and methylmercury). The HPLC-CV-rf-GD-OES detection limits for 100 microliter sample injections were found to be 1.2 and 1.8 ng mL(-1) (as mercury) of inorganic mercury and methylmercury, respectively. The reproducibility observed was below +/- 8% for both species. Finally, the HPLC-CV-rf-GD-OES system developed was successfully applied to the determination of methylmercury (speciation) in two certified reference materials, Dorm-2 and Dolt-2.     

Kinetic determination of microamounts of some sulphur-containing ligands

Some sulphur-containing ligands have been shown to inhibit the Hg(II)-catalysed substitution of p-nitrosodiphenylamine (p-NDA) for cyanide in hexacyanoferrate(II), by binding the mercury(II). This effect is used for determination of microamounts of cysteine, thioglycollic acid and thiosulphate. The reactions are followed spectrophotometrically at 640 nm (lambda(max) of [Fe(CN)(5).p-NDA](3-)). The determination range depends on the amount of mercury(II) added and the stability of the Hg(II)-ligand complex. Under specified conditions, the detection limits are: thioglycollic acid 1 x 10(-7)M, cysteine 1 x 10(-6)M and thiosulphate 4 x 10(-7)M.