Influence of aluminium precursor on physico-chemical properties of aluminium hydroxides and oxides Part II. Al(ClO4)3·9H2O

Aluminium hydroxide was precipitated during a hydrolysis of aluminium perchlorate in ammonia medium. The materials were studied with the following methods: thermal analysis, IR spectroscopy, X-ray diffraction, low-temperature nitrogen adsorption and adsorption–desorption of benzene vapours. Freshly precipitated boehmite had a high value of S_BET=211 m² g^–1 determined from nitrogen adsorption, good sorption capacity for benzene vapours, developed mesoporous structure and hydrophobic character. After prolonged refluxing at elevated temperature its crystallinity increased which was accompanied by an increase of specific surface determined from nitrogen adsorption up to 262m²g^–1 , decrease of sorption capacity for benzene vapours and stronger hydrophobic character. The calcinations of all boehmites at temperature up to 1200°C resulted in formation of à-Al₂O₃ via transition form of γ-, δ- and θ-Al₂O₃. The samples of aluminium oxides obtained after calcination at 550 and 900°C were characterised with high values of specific surface area of 205–220 and 138–153 m² g^–1 , respectively. The SBET values calculated for the oxide samples derived from aged hydroxides and calcined at 1200°C are higher than for the analogous sample prepared without the ageing step. It was concluded that the process of ageing at elevated temperature developed thermal stability of aluminium oxides.     

Influence of aluminium precursor on physico-chemical properties of aluminium hydroxides and oxides

The process of hydrolysis of aqueous aluminium sulfate was carried on in ammonia medium at 100°C and for different time intervals (0, 20, 39 or 59 h). The products thus obtained were calcined at 550, 900 or 1200°C for 2 h with the aim to obtain aluminium oxides. The materials were studied with the following methods: thermal analysis, IR spectroscopy, X-ray diffraction, low-temperature nitrogen adsorption, adsorption–desorption of benzene vapours and scanning electron microscopy. Freshly precipitated material was an amorphous basic aluminium sulfate which after prolonged refluxing at elevated temperature in a mother liquor underwent a phase transformation into highly crystalline NH₄Al₁₃(SO₄)₂(OH)₆ containing tridecameric unit Al₁₃. It was accompanied by a decrease of specific surface area and the formation of a porous structure less accessible for benzene molecules. Regardless of the duration of the hydrolysis process, all products were characterised with poorly developed porous structure and hydrophilic character. Their calcination at the temperature up to 1200°C resulted in the formation of α-Al₂O₃ via transition forms of γ/η- and δ-Al₂O₃. The samples of aluminium oxides obtained after calcination at 550 and 900°C had higher values of specific surface area than starting materials due to processes of dehydroxylation and desulfurization. The process of calcination up to 900°C was reflected in developing of not only porous structure but also hydrophobic character of prepared materials. The S _BET values calculated for the oxide samples obtained from aged products of hydrolysis at 1200°C were lower than for the analogous sample prepared without the ageing step. It was concluded that prolonged refluxing at elevated temperature of the products of hydrolysis of aluminium sulfate decreased thermal stability of final aluminium oxides.     

Influence of aluminium precursor on physico-chemical properties of aluminium hydroxides and oxides

An attempt to obtain aluminium hydroxide that could give aluminium oxides of increased thermal stability was made. Aluminium hydroxide was precipitated during a hydrolysis of aluminium chloride in ammonia medium. The influence of preparative conditions, such as a dosing rate of aluminium precursor, pH, duration of the precipitate refluxing and temperature of calcination, on the properties of obtained hydroxides and oxides was investigated. The materials were studied with the following methods: thermal analysis, IR spectroscopy, low-temperature nitrogen adsorption and adsorption–desorption of benzene vapours. Precipitated boehmites had high values of S _BET determined from nitrogen adsorption (220–300 m²g^–1), good sorption capacity for benzene vapours, developed mesoporous structure and hydrophilic character. It has been proved that a high pH value during the precipitation of aluminium hydroxide favoured better crystallisation of boehmite structure, higher temperature of its dehydroxylation into γ-Al₂O₃, and delayed transformation of γ phase into α-Al₂O₃. Aluminium oxides derived from the hydroxides precipitated at a high pH were the most stable at high temperatures, and were characterised with the best surface properties. The online version of the original article can be found at     

Thermal transformations of the products of partial hydrolysis of hydrous aluminium nitrate

Thermal analysis, mass spectrometry, infrared spectrophotometry, X-ray phase analysis, scanning electron microscopy, and sorption methods were used in the study of thermal transformations of the products of partial hydrolysis of hydrous aluminium nitrate in ammonia medium. It has been found that the process of aluminium nitrate hydrolysis under the conditions applied and in the presence of ammonia gives boehmite as the main product, with some admixture of a basic salt.Aluminium oxide obtained from the products of partial hydrolysis of hydrous aluminium nitrate in ammonia medium at 550°C has a crystalline -Al₂O₃ structure. Its specific surface, as determined by low-temperature adsorption of nitrogen, exceeds 200 m²g^–1. Features of the products are well developed mesopore structure and considerable ability of benzene adsorption. Calcination of the obtained aluminium oxide for 2 h at 900°C reduces its specific surface to about 110 m² g^–1.This revised version was published online in November 2005 with corrections to the Cover Date.     

Ni–Al hydrotalcite-like material as the catalyst precursors for the dry reforming of methane at low temperature

Nickel–aluminium and magnesium–aluminium hydrotalcites were prepared by co-precipitation and subsequently submitted to calcination. The mixed oxides obtained from the thermal decomposition of the synthesized materials were characterized by XRD, H₂-TPR, N₂ sorption and elemental analysis and subsequently tested in the reaction of methane dry reforming (DRM) in the presence of excess of methane (CH₄/CO₂/Ar = 2/1/7). DMR in the presence of the nickel-containing hydrotalcite-derived material showed CH₄ and CO₂ conversions of ca. 50% at 550 °C. The high values of the H₂/CO molar ratio indicate that at 550 °C methane decomposition was strongly influencing the DRM process. The sample reduced at 900 °C showed better catalytic performance than the sample activated at 550 °C. The catalytic performance in isothermal conditions from 550 °C to 750 °C was also determined.     

Thermal decomposition of nickel aluminium mixed hydroxides and formation of nickel aluminate spinel

Various nickel aluminium mixed hydroxide samples of different compositions were prepared by co-precipitation from their nitrate solutions using dilute NH₄OH. Additional samples were prepared by impregnation of hydrated Al₂O₃, preheated at 600 and 900°C, with nickel nitrate solution in an equimolar ratio. The thermal decomposition of different mixed solids was studied using DTA. The X-ray investigation of thermal products of the mixed solids was also studied.The results obtained revealed that the presence of NiO up to 33.3 mole % with aluminium oxide much enhanced the degree of crystallinity of the γ-Al₂O₃ phase. In contrast, the presence of Al₂O₃ much retarded the crystallization process of the NiO phase. With the exception of samples containing 20 mole% NiO, all the mixed hydroxide samples, when heated in air at 900°C, led to the formation of well-crystalline Ni Al₂O₄ spinel, alone, or together with either NiO or γ-Al₂O₃, depending on the composition of the mixed oxide samples. The solid containing 20% NiO and heated at 900°C was constituted of amorphous NiO dispersed in γ-Al₂O₃. Heating the nickel nitrate-impregnated Al₂O₃ in air at 800–1000°C led to the formation of Ni Al₂O₄ together with non-reacted NiO and γ-Al₂O₃. The degree of crystallinity of the spinel was found to increase by increasing the calcination temperature of the impregnated solids from 800 to 1000°C and by increasing the preheating temperature of the hydrated Al₂O₃ employed from 600 to 900°C.     

Effects of doping with CeO2 and calcination temperature on physicochemical properties of the NiO/Al2O3 system

The effects of doping with CeO₂ and calcination temperature on the physicochemical properties of the NiO/Al₂O₃ system have been investigated using DTA, XRD, nitrogen adsorption measurements at −196°C and decomposition of H₂O₂ at 30–50°C. The pure and variously doped solids were subjected to heat treatment at 300, 400, 700, 900 and 1000°C. The results revealed that the specific surface areas increased with increasing calcination temperature from 300 to 400°C and with doping of the system with CeO₂. The pure and variously doped solids calcined at 300 and 400°C consisted of poorly crystalline NiO dispersed on γ-Al₂O₃. Heating at 700°C resulted in formation of well crystalline NiO and γ-Al₂O₃ phases beside CeO₂ for the doped solids. Crystalline NiAl₂O₄ phase was formed starting from 900°C. The degree of crystallinity of NiAl₂O₄ increased with increasing the calcination temperature from 900 to 1000°C. An opposite effect was observed upon doping with CeO₂. The NiO/Al₂O₃ system calcined at 300 and 400°C has catalytic activity higher than individual NiO obtained at the same calcination temperatures. The catalytic activity of NiO/Al₂O₃ system increased, progressively, with increasing the amount of CeO₂ dopant and decreased with increasing the calcination temperature.     

Aluminium nitrate as a precursor of mesoporous aluminium oxides

The thermal transformations of the products of hydrous aluminium nitrate hydrolysis in ammonia medium were studied by thermal analysis, mass spectrometry, infrared spectrophotometry, X-ray phase analysis, and sorption methods. Experiments have shown that the hydrolysis of hydrous aluminium nitrate in ammonia medium at pH=6-7 leads to the formation of boehmite. The degree of crystallinity of this product increases, if the hydrolysis is carried out for 264 h at 100°C, with respect the samples separated from the mother liquor just after completing the dosage of the reagents. It has also been found that aluminium oxide, obtained by thermal decomposition of the products of hydrolysis carried out for 264 h at an increased temperature, is characterized by a well developed specific surface, stable at high temperatures, amounting to about 100 m2 g^-1, after calcination for 2 h at 1200°C. This revised version was published online in July 2006 with corrections to the Cover Date.     

Study of the catalysts for fuel combustion reactions: XIX. Thermal stability of alumina promoted with lanthanum and silicon

X-ray diffraction analysis and data on the strength and specific surface area are used to study the thermal stability of a La-Si/Al₂O₃ system depending on the concentration of introduced additives and calcination temperature. The mechanisms of interactions of these elements and alumina are discussed. Silicon and lanthanum cations begin to interact at low temperatures (∼500‡C). The authors assume that silicon and lanthanum cations occupy tetrahedral and octahedral positions, respectively, in the γ-alumina lattice and thus significantly enhance its thermal stability. Up to 50% of γ-Al₂O₃ is retained at 1200‡C, and α-Al₂O₃ starts to form in the ternary system only at 1300‡C.     

Infrared absorption spectra of Er3+-doped Al2O3 nanopowders by the sol-gel method

The Er³⁺-doped Al₂O₃ nanopowders have been prepared by the sol-gel method, using the aluminium isopropoxide [Al(OC₃H₇)₃]-derived γ-AlOOH sols with addition of the erbium nitrate [Er(NO₃)₃·5H₂O]. The five phases of γ-(Al,Er)₂O₃, θ-(Al,Er)₂O₃, α-(Al,Er)₂O₃, ErAlO₃, and Al₁₀Er₆O₂₄ were detected with the 0–20 mol% Er³⁺-doped Al₂O₃ nanopowders at the different sintering temperature of 600–1200°C. The average grain size was increased from about 5 to 62 nm for phase transformation of undoped γ-Al₂O₃→α-Al₂O₃ at the sintering temperature from 600 to 1200°C. At the same sintering temperature, average grain size was decreased with increase of the Er³⁺ doping concentration. Infrared absorption spectra of γ-Al₂O₃ and θ-Al₂O₃ nanopowders showed the two broad bands of 830–870 and 550–600 cm⁻¹, the three broad bands of 830–870, 750–760, and 550–600 cm⁻¹, respectively. The infrared absorption spectra for the α-Al₂O₃ nanopowder showed three characteristic bands, 640, 602, and 453 cm⁻¹. The two characteristic bands of 669 and 418 cm⁻¹ for Er₂O₃ clusters were observed for the Er³⁺-doped Al₂O₃ nanopowders when Er³⁺ doping concentration was increased up to 2 mol%. The 796, 788, 725, 692, 688, 669, 586, 509, 459, and 418 cm⁻¹ are the characteristic bands of Al₁₀Er₆O₂₄ phase.     

Effects of calcination and support on supported manganese catalysts for the catalytic oxidation of toluene as a model of VOCs

The conventional impregnation method was used to prepare 15 wt% Mn-supported catalysts, which were applied to the catalytic oxidation of volatile organic compounds (VOCs; toluene, benzene, and o-xylene). The effects of calcination temperatures in the range of 500–900 °C and supports (γ-Al₂O₃, SiO₂, and TiO₂) on the property and performance of 15 wt% Mn-supported catalysts were investigated. Their physicochemical characteristics were analyzed by the BET, XRD, NH₃–TPD, H₂–TPR, and XPS. The calcination temperature greatly affected the crystalline structure and O1s _D (defect oxides)/O1s _L (lattice oxides) area ratio of the 15 wt% Mn/γ-Al₂O₃ (15 Mn/Al) catalyst. The order of the O1s _D/O1s _L area ratios of the 15 Mn/Al catalysts with respect to calcination temperature was 900 > 500 > 700 °C, which was in good agreement with that observed for the catalytic activity. In addition, the activity order of the 15 wt% Mn-supported catalysts with respect to the type of support was γ-Al₂O₃ > SiO₂ > TiO₂. The 15 wt% Mn/Al catalyst, which had a higher O1s _D/O1s _L area ratio, showed better activity than the 15 wt% Mn/SiO₂ (15 Mn/Si) and 15 wt% Mn/TiO₂ (15 Mn/Ti) catalysts. Defect oxides played a significant role in the catalytic oxidation of VOCs. The catalytic activity with respect to the type of VOC decreased in the order of benzene > toluene > o-xylene.     

Physico–chemical properties of CdO–Al2O3 catalysts. I – Structural characteristics

Alumina gels AN6 and AN7 were prepared by precipitation with NaOH from hydrated aluminum sulfate at pH 6 and 7, respectively. A third alumina gel AA7 was similarly prepared, but by precipitation with 30% ammonia. Pure cadmia C8 and C9 were precipitated from cadmium sulfate at pH 8 and 9 using NaOH. Five mechanically mixed gels ACM (1:0.25), ACM (1:0.5), ACM (1:1), ACM (0.5:1) and ACM (0.25:1) were prepared by thoroughly mixing the appropriate molar ratios of AN7 and C8. Also, five coprecipitated gels ACC (1:0.25), ACC (1:0.5), ACC (1:1), ACC (0.5:1) and ACC (0.25:1) were coprecipitated by dropping simultaneously the appropriate volumes of 1 M aluminum sulfate, 1 M cadmium sulfate and 3 M NaOH. Calcination products at 400, 500, 600, 800 and 1000 °C were obtained from each preparation.TG–DTA patterns of uncalcined samples were analyzed and the XRD of all 1000 °C-products and some selected samples calcined at 400–800 °C were investigated. The thermal behaviors of pure and mixed gels depend on the precipitating agent, pH of precipitation, chemical composition and method of preparation. Generally, calcination at temperatures below 800 °C gave poorly crystalline phases. Well crystalline phases are obtained at 800 and 1000 °C. For pure alumina γ-Al₂O₃ was shown as 400 °C-calcination product that transforms into the δ form around 900 °C and later to θ-Al₂O₃ as a major phase and α-Al₂O₃ as a minor phase at 1000 °C. CdO was shown by 500 °C-calcined cadmia gel that showed color changes with rise of calcination temperature. The most stable black cadmium oxide phase (Monteponite) is obtained upon calcination at 1000 °C. Thousand degree celsius- calcined mixed oxides showed θ-Al₂O₃, α-Al₂O₃, CdAl₂O₄ and monteponite which dominate depending on the chemical composition.     

Fixation de divers polluants dans des alumines monolithiques poreuses

Fixation of various pollutants in a monolithic porous alumina. Ultraporous monoliths of hydrated alumina, prepared at room temperature by atmospheric air oxidation of aluminium, can fix various gaseous phases, for instance up to 1.25 kg hydrogen chloride per kg. The material porosity remains high after heating at 1200–1300°C. Then, this alumina can be impregnated by aqueous solutions of various salts, which result in oxides after drying and calcination. These oxides are confined within the material. For instance, 1 kg monolith can contain more than 2 kg cerium oxide, which serves as a model for the behaviour of transuranium element oxides (PuO₂, AcO₂) contained in radioactive waste.     

Untersuchungen an oxidischen Katalysatoren. XIV. Die katalytische Aktivität verschiedener Übergangsformen des Aluminiumoxids bei der Dehydratisierung von Isopropanol

Studies on Oxide Catalysts. XIV. The catalytic Activity of some transient Forms of Alumina in the Dehydration of Isopropanol In order to give statements about the influence of the method of preparation of aluminum hydroxides and oxide hydroxides on the catalytic properties of alumina obtained from these compounds in the dehydration of ispropanol, bayerite, nordstrandite, and boehmite were prepared by several methods, carefully excluding impurity ions. Also, hydrargillite containing alkali was included in the investigations. By calcination in oxygen at 550 and 950°C, respectively, two groups of alumina were obtained. The catalytic properties of the oxides in the dehydration of isopropanol were examined by an apparatus working according to the dynamic principle. The specific activities of the different transient forms of alumina were found to vary according to the sequence η-;≈γ->?-≈δ->??(>??-)Al₂O₃.     

Effects of calcination and activation temperature on dry reforming catalysts

The effect of calcination temperatures on dry reforming catalysts supported on high surface area alumina Ni/γ-Al₂O₃ (SA-6175) was studied experimentally. In this study, the prepared catalyst was tested in a micro tubular reactor using temperature ranges of 500, 600, 700 and 800 °C at atmospheric pressure, using a total flow rate of 33 ml/min consisting of 3 ml/min of N₂, 15 ml/min of CO₂ and 15 ml/min of CH₄. The calcination was carried out in the range of 500–900 °C. The catalyst is activated inside the reactor at 500–800 °C using hydrogen gas. It was observed that calcination enhances catalyst activity which increases as calcination and reaction temperatures were increased. The highest conversion was obtained at 800 °C reaction temperature by using catalyst calcined at 900 °C and activation at 700 °C. The catalyst characterization conducted supported the observed experimental results.     

Selective Formation of Spinel Iron Oxide in Thin Films by Complexing Agent-Assisted Sol-Gel Processing

The structure of iron oxide was controlled by regulating the hydrolytic polymerization of aquo iron complexes with organic polydentate ligands such as diols. Iron oxides were prepared by calcining the precursor polymers obtained from iron nitrate nonahydrate and diols. When the diols were 1,2-pentanediol, 1,2-hexanediol and 1,2-octanediol, α-Fe₂O₃ with corundum structure appeared exclusively or as the main crystalline phase, in spite of the amount of diol used and the calcination temperature. In the case of 1,2-decanediol and 1,2-dodecanediol, when five moles of the diols were used to one mole of iron nitrate and the calcination temperatures were below 400°C, ψ-Fe₂O₃ with spinel structure appeared as the main phase and, when less than five moles of the diols were used, α-Fe₂O₃ appeared exclusively or as the main phase, irrespective of the calcination temperature. This tendency was also observed in thin films. Thus, a transparent magnetic film composed of γ-Fe₂O₃ could be prepared by applying a benzene solution of the iron polymer, obtained with 5 equivalents of 1,2-decanediol, on quartz and calcining the gel film at 350°C.     

Effect of silica on the stability of the nanostructure and texture of fine-particle alumina

The effect of the modification of aluminum oxide with silicon oxide on the stability of fine-particle Γ- and δ-Al₂O₃ phases upon heat treatment in the wide temperature range of 550–1500°C was studied. It was found that the Γ- and δ-Al₂O₃ phases modified with silica are thermally stable up to higher temperatures than pure aluminum oxide. This is due to changes in the real structure of the modified samples, specifically, an increase in the concentration of extensive defects stabilized by hydroxyl groups bound to not only aluminum atoms but also silicon atoms. It is likely that Si-OH groups, which are thermally more stable than Al-OH groups, stabilize the microstructure of Γ- and δ-Al₂O₃ to higher temperatures, as compared with aluminum oxide containing no additives. Simultaneously, an increase in the thermal stability of the modified samples is accompanied by the retention of a high specific surface area and a developed pore structure at higher treatment temperatures.     

Conductivity,oxygen interfacial exchange and diffusion in oxides based on lanthanum gallate

The method of isotopic exchange was used to study the oxygen exchange kinetics in the oxides of La_0.88Sr_0.12Ga_0.82Mg_0.18O_{3 − δ} and La_0.80Sr_0.20Ga_0.85−x Mg_0.15Co _x O_{3 − δ} (x = 0.05, 0.15, 0.20, 0.25). The rates of oxygen exchange and its diffusion coefficients were determined in the temperature range of 600–900°C at the oxygen pressure of 5 torr. The fractions of the three exchange types for the oxides studied were determined at the temperature of 817°C and oxygen pressure of 5 torr. The total conductivity of the oxides of La_0.80Sr_0.20Ga_0.85−x Mg_0.15Co _x O_{3 − δ} (x = 0.05, 0.15, 0.20, 0.25) was measured in the temperature range of 550–850°C in air and at the temperature of 800°C in the range of oxygen pressures of 1–760 torr. It was shown that an increase in the electronic conductivity component due to an increase in the cobalt fraction in the gallium sublattice results in growing interfacial exchange rate, total conductivity of the studied systems, and a decrease in the effective conductivity activation energy.     

Thermal and morphological study of Al2O3 nanofibers derived from boehmite precursor

The boehmite nanofibers were prepared by using NaAlO₂ and Al₂(SO₄)₃ as the starting materials without any surfactant. The phase transitions of the boehmite nanofibres against different temperature were studied and various phases were derived from well-crystallized boehmite nanofibers. All these phases had the same morphology even after high temperature calcination. In addition, the retention of specific surface area of the samples were very high because of the limited aggregation occurred in calcinations for each sample. For instance, the ??-Al₂O₃ obtained at 500?°C had the specific surface area (208.56?m²/g) with an average pore diameter of 6.0?nm. With the further increase of the calcination temperature, the nanofibers became shorter and coarsening, which resulted in the decrease of the specific surface area. It is worthwhile to notice that the BET surface areas (40.97?m²/g) and the pore volume (0.27?cm³/g) of the fibrous structures obtained after 1200?°C calcination are substantially higher than that of the non-fibrous alumina because of the morphology maintenance.     

Effect of pH, ionic strength, foreign ions, fulvic acid and temperature on 109Cd(II) sorption to γ-Al2O3

The sorption of Cd(II) from aqueous solution on γ-Al₂O₃ was investigated under ambient conditions. Experiments were carried out as a function of contact time, solid content, pH, ionic strength, foreign ions, fulvic acid and temperature. The results indicated that the sorption of Cd(II) was strongly dependent on pH and ionic strength. At low pH, the sorption of Cd(II) was dominated by outer-sphere surface complexation and ion exchange with Na⁺/H⁺ on γ-Al₂O₃ surfaces, whereas inner-sphere surface complexation was the main sorption mechanism at high pH. The Langmuir, Freundlich and Dubinin–Radushkevich (D–R) models were used to simulate the sorption isotherms at three different temperatures. The thermodynamic data (ΔG ⁰, ΔS ⁰, ΔH ⁰) calculated from the temperature dependent sorption isotherms suggested that the sorption of Cd(II) on γ-Al₂O₃ was an spontaneous and endothermic process.