Preparation of polyynes by laser ablation of graphite in aqueous media

Polyynes were prepared by liquid-phase laser ablation of a graphite target at 1064 nm and identified by analyzing UV absorption spectra in deionized water and various aqueous solutions. We observed that major UV absorption peaks coincide with the electronic transitions corresponding to linear hydrogen-capped polyynes (C_nH₂: n = 6, 8, 10). The peak intensities increased when polyynes were produced by irradiating the target immersed in acidic media, while those were relatively weak in basic media. This leads us to conclude that OH⁻ or H⁺ ions play a certain role in the formation of polyynes.     

Femtosecond pulsed laser ablation of diamond-like carbon films on silicon

Femtosecond pulsed laser ablation (τ = 120 fs, λ = 800 nm, repetition rate = 1 kHz) of thin diamond-like carbon (DLC) films on silicon was conducted in air using a direct focusing technique for estimating ablation threshold and investigating the influence of ablation parameter on the morphological features of ablated regions. The single-pulse ablation threshold estimated by two different methods were ?_th(1) = 2.43 and 2.51 J/cm². The morphological changes were evaluated by means of scanning electron microscopy. A comparison with picosecond pulsed laser ablation shows lower threshold and reduced collateral thermal damage.     

Galvanomagnetic properties of air-stable and highly conductive potassium-intercalated graphite sheet

Magnetoresistance and Hall coefficient of air-stable potassium-intercalated graphite sheets (hereafter abbreviated as K-PGS) were determined at room temperature. The magnitude of the magnetoresistance and the absolute value of Hall coefficient of K-PGS decreased with increasing potassium content of K-PGS, n_K/n_C. Two-carrier model was used for calculating carrier density and mobility. The electron density increased with increasing n_K/n_C: 3.07×10²⁰ cm⁻³ (n_K/n_C=0.005), 5.67×10²⁰ cm⁻³ (n_K/n_C=0.008) and 6.40×10²⁰ cm⁻³ (n_K/n_C=0.011). The value of the electron density of K-PGS with n_K/n_C=0.011 (nominal composition KC₉₁) was about 80% of the reported value, 7.8×10²⁰ cm⁻³, for KC₄₈ (n_K/n_C=0.021) prepared from HOPG (highly oriented pyrolytic graphite). The mobility decreased with increasing n_K/n_C: 2.11×10³ cm² V⁻¹ s⁻¹ (n_K/n_C=0.005), 1.42×10³ cm² V⁻¹ s⁻¹ (n_K/n_C=0.008) and 1.34×10³ cm² V⁻¹ s⁻¹ (n_K/n_C=0.011). The value of the mobility of K-PGS with n_K/n_C=0.011 was about 60% of the reported value (2300 cm² V⁻¹ s⁻¹) for KC₄₈ prepared from HOPG.     

Microfabrication and magnetoelectric properties of amorphous magnetic-tunnel-junctions with Co–Fe–B/Al–O/Co–Fe–B hardcore structure

Both single-barrier magnetic tunnel junctions (SBMTJs) and double-barrier magnetic tunnel junctions (DBMTJs) with an amorphous hardcore structure of Co₆₀Fe₂₀B₂₀/Al–O/Co₆₀Fe₂₀B₂₀ were microfabricated. A high TMR ratio of 102.2% at 4.2 K was observed in the SBMTJs after annealing at 265 °C for 1 h. High TMR ratio of 56.2%, low junction resistance-area product RS of 4.6 kΩ μm², small coercivity H_C=25 Oe, and relatively large bias-voltage-at-half-maximum TMR with the value V_1/2 greater than 500 mV at room temperature (RT) had been achieved in such Co–Fe–B SBMTJs. Whereas, high TMR ratio of 60% at RT and 89% at 30 K, low junction resistance-area product RS of 7.8 kΩ μm² at RT and 8.3 kΩ μm² at 30 K, low coercivity H_C=8.5 Oe at RT and H_C=14 Oe at 30 K, and relatively large bias-voltage-at-half-maximum TMR with the value V_1/2 greater than 1150 mV at RT had been achieved in the Co–Fe–B DBMTJs. Temperature dependence of the TMR ratio, resistance, and coercivity from 4.2 K to RT, and applied voltage dependence of the TMR ratio and resistance at RT for such amorphous MTJs were also investigated.     

Mechanism of ablation of CdS at laser wavelengths in the visible and in the UV

The mechanisms of laser ablation of CdS targets at different laser wavelengths have been investigated. (CdS)_n⁺ cluster formation is only observed upon 532 nm ablation. The time and energy distributions of neutral S, S₂, Cd and CdS show significant dependence on laser wavelength. Bimodal distributions are observed at 266 and 308 nm. For the former, the average kinetic energy increases significantly with mass, taking values in the range of 0.3-1.7 eV. At 308 nm the slow component of the time distribution disappears at distances above the target larger than 1 cm. At this wavelength, the observed time distribution appears to reflect mainly the dynamics of the expansion. At 532 nm the time distribution is monomodal and the average kinetic energies are below 0.2 eV. Clear indications of the participation of thermal (at 532 nm) and non-thermal mechanisms (at 266 nm) have been found. It is tentatively concluded that the cluster formation observed upon ablation at 532 nm can be related to the thermal ablation mechanisms in which the low kinetic energy of the species in the plume and their similar velocities favor the aggregation processes.     

Resonantly enhanced three-photon excitation spectra of lithium

We present the first measurement on the resonantly enhanced three-photon excitation spectra of natural lithium using a Nd:YAG laser pumped dye laser in conjunction with a thermionic diode ion detector. Exploiting the linear and circular polarizations, the np ²P_3/2(8 ? n ? 11) and nf  ²F_7/2 (8 ? n ? 38) series have been observed via three-photon excitation from the ground state. The measured level energies reveal a dynamic shift from calculated values, which increases with an increase of the principal quantum number n. The ac stark shift and line broadening mechanisms are studied as a function of laser intensity. It is noted that the width increases and the line center shifts towards the higher energy side as the laser intensity is increased. The maximum observed shift for the 12f ²F_7/2 line is 0.33 cm⁻¹ corresponding to the laser intensity variation from 1.34 × 10¹² W/m² to 1.03 × 10¹³ W/m², whereas its width increases from 0.36 cm⁻¹ to 0.82 cm⁻¹.     

Plasma characterization and room temperature growth of carbon nanotubes and nano-onions by excimer laser ablation

The deposition of carbon nanotubes and carbon nano-onions at room temperature using excimer laser radiation to ablate mixed graphite-metal targets is described. Our deposition conditions are in contrast to other investigations on the pulsed laser deposition of carbon nanotubes that have employed high temperatures and high pressures. We find that the formation of these carbon nanostructures is dependent on the ambient gas employed during ablation. In the presence of O₂ gas, carbon nanotubes and nano-onions are produced, while inert atmospheres such as Ar yield amorphous carbon. High-resolution, in situ, time-resolved emission spectroscopy has been used to track the evolution of species (C₂, C₃, Ni/Co) in the ablation plume. Spectral fits on low and high-resolution spectra reveal that the vibrational-rotational temperatures for C₂ produced in O₂ remain at ∼5000 K for nearly 20 μs but drop rapidly in Ar. Details of the formation of carbon nanotubes and nano-onions, and in situ time-resolved optical emission spectroscopy are described.     

Characterization of the laser ablation plasma used for the deposition of amorphous carbon

The plasma produced by laser ablation of a graphite target was studied by means of optical emission spectroscopy and a Langmuir planar probe. Laser ablation was performed using a Nd:YAG laser with emission at the fundamental line with pulse length of 28 ns. In this work, we report the behavior of the mean kinetic energy of plasma ions and the plasma density, as a function of the laser fluence (J/cm²), and the target to probe (substrate) distance. The characterized regimes were employed to deposit amorphous carbon at different values of kinetic energy of the ions and plasma density. The mean kinetic energy of the ions could be changed from 40 to 300 eV, and the plasma density could be varied from 1 × 10¹² to 7 × 10¹³ cm⁻³. The main emitting species were C⁺ (283.66, 290.6, 299.2 and 426.65 nm) and C⁺⁺ (406.89 and 418.66 nm) with the C⁺ (426.65 nm) being the most intense and that which persisted for the longest times. Different combinations of the plasma parameters yield amorphous carbon with different structures. Low levels (about 40 eV) of ion energy produce graphitic materials, while medium levels (about 200 eV) required the highest plasma densities in order to increase the CC sp³ bonding content and therefore the hardness of the films. The structure of the material was studied by means of Raman spectroscopy, and the hardness and elastic modulus by depth sensitive nanoindentation.     

Energy distributions of atomic and molecular ions sputtered by C60 projectiles

In the process of investigating the interaction of fullerene projectiles with adsorbed organic layers, we measured the kinetic energy distributions (KEDs) of fragment and parent ions sputtered from an overlayer of polystyrene (PS) oligomers cast on silver under 15 keV C₆₀⁺ bombardment. These measurements have been conducted using our TRIFT™ spectrometer, recently equipped with the C₆₀⁺ source developed by Ionoptika, Ltd. For atomic ions, the intensity corresponding to the high energy tail decreases in the following order: C⁺(E^−0.4) > H⁺(E^−1.5) > Ag⁺(E^−3.5). In particular, the distribution of Ag⁺ is not broader than those of Ag₂⁺ and Ag₃⁺ clusters, in sharp contrast with 15 keV Ga⁺ bombardment. On the other hand, molecular ions (fragments and parent-like species) exhibit a significantly wider distribution using C₆₀⁺ instead of Ga⁺ as primary ions. For instance, the KED of Ag-cationized PS oligomers resembles that of Ag⁺ and Ag_n⁺ clusters. A specific feature of fullerene projectiles is that they induce the direct desorption of positively charged oligomers, without the need of a cationizing metal atom. The energy spectrum of these PS⁺ ions is significantly narrower then that of Ag-cationized oligomers. For characteristic fragments of PS, such as C₇H₇⁺ and C₁₅H₁₃⁺ and polycyclic fragments, such as C₉H₇⁺ and C₁₄H₁₀⁺, the high energy decay is steep (E⁻⁴ − E⁻⁸). In addition, reorganized ions generally show more pronounced high energy tails than characteristic ions, similar to the case of monoatomic ion bombardment. This observation is consistent with the higher excitation energy needed for their formation. Finally, the fraction of hydrocarbon ions formed in the gas phase via unimolecular dissociation of larger species is slightly larger with gallium than with fullerene projectiles.     

Ablation characteristics of aluminum oxide and nitride ceramics during femtosecond laser micromachining

Femtosecond laser ablation of aluminum oxide (Al₂O₃) and aluminum nitride (AlN) ceramics was performed under normal atmospheric conditions (λ = 785 nm, τ_p = 185 fs, repetition rate = 1 kHz), and threshold laser fluencies for single- and multi-pulse ablation were determined. The ablation characteristics of the two ceramics showed similar trends except for surface morphologies, which revealed virtually no melting in Al₂O₃ but clear evidence of melting for AlN. Based on subsequent X-ray photoelectron spectroscopy (XPS) analyses, the chemistry of these ceramics appeared to remain the same before and after femtosecond laser ablation.     

Laser impulse coupling at 130 fs

We measured the momentum coupling coefficient C_m and laser-generated ion drift velocity and temperature in the femtosecond (fs) region, over a laser intensity range from ablation threshold to about one hundred times threshold. Targets were several pure metals and three organic compounds. The organic compounds were exothermic polymers specifically developed for the micro-laser plasma thruster, and two of these used “tuned absorbers” rather than carbon particles for laser absorption. The metals ranged from Li to W in atomic weight. We measured time of flight (TOF) profiles for ions. Specific impulse reached record values for this type of measurement and ablation efficiency was near 100%. These measurements extend the laser pulsewidth three orders of magnitude downward in pulsewidth relative to previous reports. Over this range, we found C_m to be essentially constant. Ion velocity ranged from 60 to 180 km/s.     

Nano-graphene structures deposited by N-IR pulsed laser ablation of graphite on Si

Thin nano-structured carbon films have been deposited in vacuum by pulsed laser ablation, from a rotating polycrystalline graphite target, on Si 〈1 0 0〉 substrates, kept at temperatures ranging from RT to 800 °C. The laser ablation was performed by a Nd:YAG laser, operating in the near IR (λ = 1064 nm).X-ray diffraction analysis, performed at grazing incidence angle, both in-plane (ip-gid) and out-of-plane (op-gid), has shown the growth of oriented nano-sized graphene particles, characterised by high inter-planar stacking distance (d_? ∼ 0.39 nm), compared to graphite. The film structure and texturing are strongly related both to laser wavelength and substrate temperature: the low energy associated to the IR laser radiation (1.17 eV) generates activated carbon species of large dimensions that, also at low T (∼400 °C), easy evolve toward more stable sp² aromatic bonds, in the plume direction. Increasing temperature the nano-structure formation increases, causing a further aggregation of aromatic planes, voids formation, and a related density (by X-ray reflectivity) drop to very low values. SEM and STM show for these samples a strongly increased macroscopic roughness. The whole process, mainly at higher temperatures, is characterised by a fast kinetic mode, far from equilibrium and without any structural or spatial rearrangement.     

Formation of Sim and SimCn clusters by C60 sputtering of Si

The secondary ion mass spectrum of silicon sputtered by high energy C₆₀⁺ ions in sputter equilibrium is found to be dominated by Si clusters and we report the relative yields of Si_m⁺ (1 ≤ m ≤ 15) and various Si_mC_n⁺ clusters (1 ≤ m ≤ 11 for n = 1; 1 ≤ m ≤ 6 for n = 2; 1 ≤ m ≤ 4 for n = 3). The yields of Si_m⁺ clusters up to Si₇⁺ are significant (between 0.1 and 0.6 of the Si⁺ yield) with even numbered clusters Si₄⁺ and Si₆⁺ having the highest probability of formation. The abundances of cluster ions between Si₈⁺ and Si₁₁⁺ are still significant (>1% relative to Si⁺) but drop by a factor of ∼100 between Si₁₁⁺ and Si₁₃⁺. The probability of formation of clusters Si₁₃⁺-Si₁₅⁺ is approximately constant at ∼5 × 10⁻⁴ relative to Si⁺ and rising a little for Si₁₅⁺, but clusters beyond Si₁₅ are not detected (Si_m≥16⁺/Si⁺ < 1 × 10⁻⁴). The probability of formation of Si_m⁺ and Si_mC_n⁺ clusters depends only very weakly on the C₆₀⁺ primary ion energy between 13.5 keV and 37.5 keV. The behaviour of Si_m⁺ and Si_mC_n⁺ cluster ions was also investigated for impacts onto a fresh Si surface to study the effects that saturation of the surface with C₆₀⁺ in reaching sputter equilibrium may have had on the measured abundances. By comparison, there are very minor amounts of pure Si_m⁺ clusters produced during C₆₀⁺ sputtering of silica (SiO₂) and various silicate minerals. The abundances for clusters heavier than Si₂⁺ are very small compared to the case where Si is the target.The data reported here suggest that Si_m⁺ and Si_mC_n⁺ cluster abundances may be consistent in a qualitative way with theoretical modelling by others which predicts each carbon atom to bind with 3-4 Si atoms in the sample. This experimental data may now be used to improve theoretical modelling.     

Nanostructures on SiC surface created by laser microablation

Silicon carbide (SiC), as it is well-known, is inaccessible to usual methods of technological processing. Consequently, it is important to search for alternative technologies of processing SiC, including laser processing, and to study the accompanying physical processes. The work deals with the investigation of pulsed laser radiation influence on the surface of 6H-SiC crystal. The calculated temperature profile of SiC under laser irradiation is shown. Structural changes in surface and near-surface layers of SiC were studied by atomic force microscopy images, photoluminescence, Raman spectra and field emission current-voltage characteristics of initial and irradiated surfaces. It is shown that the cone-shaped nanostructures with typical dimension of 100-200 nm height and 5-10 nm width at the edge are formed on SiC surface under nitrogen laser exposure (λ = 0.337 μm, t_p = 7 ns, E_p = 1.5 mJ). The average values of threshold energy density 〈W_thn〉 at which formation of nanostructures starts on the 0 0 0 1 and surfaces of n-type 6H-SiC(N), nitrogen concentration n_N ≅ 2 × 10¹⁸ cm⁻³, are determined to be 3.5 J/cm² and 3.0 J/cm², respectively. The field emission appeared only after laser irradiation of the surface at threshold voltage of 1000 V at currents from 0.7 μA to 0.7 mA. The main role of the thermogradient effect in the processes of mass transfer in prior to ablation stages of nanostructure formation under UV laser irradiation (LI) was determined. We ascertained that the residual tensile stresses appear on SiC surface as a result of laser microablation. The nanostructures obtained could be applied in the field of sensor and emitting extreme electronic devices.     

Sputtering of neutral clusters from silver-gold alloys

Polycrystalline Ag, Ag₂₀Au₈₀, Ag₄₀Au₆₀, Ag₈₀Au₂₀ and Au samples were bombarded with 15 keV Ar⁺ at 60° incidence and the resulting secondary neutral yield distribution was studied by non-resonant laser postionisation mass spectrometry. Neutral clusters containing up to 21 atoms were observed for the targets. The yield of neutral clusters, Ag_mAu_n−m, containing n atoms, Y_n, was found to follow a power in n, i.e. Y_n ∝ n^−δ, where the exponent δ varied from 3.2 to 4.0. For a fixed n, the cluster yields showed a variation with number of gold atoms similar to that expected for a binomial distribution. In addition, the cluster compositions from the sputtered alloys were indicative of sputtering from a gold rich surface.     

Multi-step laser excitation of the highly excited states of zinc

We report experimental data on the highly excited states of zinc in the energy range 74,625-75,740 cm⁻¹ using two-step laser excitation scheme in conjunction with a thermionic diode ion detector. The 4s4p ³P₁ inter-combination level at 32501.399 cm⁻¹ was populated using a frequency doubled dye laser. The 4s5s ³S₁ level at 53672.28 cm⁻¹ gets populated from the ASE (amplified spontaneous emission) of the second step dye laser. The Rydberg series 4snp ³P₂ (12 ? n ? 60), 4snp ¹P₁ (16 ? n ? 30) and parity forbidden transitions 4sns ³S₁ (19 ? n ? 44) have been observed. A two parameter fit to excitation energies of the observed series yields the binding energy of the 4s5s ³S₁ level as 22097.03 ± 0.03 cm⁻¹ and consequently, the first ionization potential of zinc is determined as 75769.31 ± 0.05 cm⁻¹, that is in excellent agreement with the earlier work.     

Carbon-plasma produced in vacuum by 532 nm-3 ns laser pulses ablation

A study of VIS laser ablation of graphite, in vacuum, by using 3 ns Nd:YAG laser radiation is reported. Nanosecond pulsed ablation gives an emission mass spectrum attributable to C_n neutral and charged particles. Mass quadrupole spectroscopy, associated to electrostatic ion deflection, allows estimation of the velocity distributions of several of these emitting species within the plume as a function of the incident laser fluence. Time gated plume imaging and microscopy measurements have been used to study the plasma composition and the deposition of thin carbon films. The multi-component structure of the plume emission is rationalized in terms of charge state, ions temperature and neutrals temperature. A special regard is given to the ion acceleration process occurring inside the plasma due to the high electrical field generated in the non-equilibrium plasma conditions. The use of nanosecond laser pulses, at fluences below 10 J/cm², produces interesting C-atomic emission effects, as a high ablation yield, a high fractional ionization of the plasma and presence of nanostructures deposited on near substrates.     

Molecular dynamics simulation of femtosecond ablation and spallation with different interatomic potentials

Fast heating of target material by femtosecond laser pulse (fsLP) with duration τ_L∼40-100 fs results in the formation of thermomechanically stressed state. Its unloading may cause frontal cavitation of subsurface layer at a depth of 50 nm for Al and 100 nm for Au. The compression wave propagating deep into material hits the rear-side of the target with the formation of rarefaction wave. The last may produce cracks and rear-side spallation. Results of MD simulations of ablation and spallation of Al and Au metals under action fsLP are presented. It is shown that the used EAM potentials (Mishin et al. and our new one) predict the different ablation and spallation thresholds on absorbed fluence in Al: ablation F_a=60{65} mJ/cm²and spallation F_s=120{190} mJ/cm², where numbers in brackets { } show the corresponding values for Mishin potential. The strain rate in spallation zone was 4.3×10⁹ 1/s at spallation threshold. Simulated spall strength of Al is 7.4{8.7} GPa, that is noticeably less than 10.3{14} GPa obtained from acoustic approximation with the use of velocity pullback on velocity profile of free rear surface. The ablation threshold F_a≈120 mJ/cm² and crater depth of 110 nm are obtained in MD simulations of gold with the new EAM potential. They agree well with experiment.     

Local chemical transformations in poly(dimethylsiloxane) by irradiation with 248 and 266 nm

Poly(dimethylsiloxane) (PDMS) has been irradiated with a frequency quadrupled Nd:YAG laser and a KrF^*-excimer laser at a repetition rate of 1 Hz. The analysis of ablation depth versus pulse number data reveals a pronounced incubation behavior. The thresholds of ablation (266 nm: 210 mJ cm⁻², 248 nm: 940 mJ cm⁻²) and the corresponding effective absorption coefficients α_eff (266 nm: 48900 cm⁻¹, 248 nm: 32700 cm⁻¹, α_lin = 2 cm⁻¹) were determined. The significant differences in the ablation thresholds for both irradiation wavelengths are probably due to the different pulse lengths of both lasers. Since the shorter pulse length yields a lower ablation threshold, the observed incubation can be due to a thermally induced and/or a multi-photon absorption processes of the material or impurities in the polymer.Incubation of polymers is normally related to changes of the chemical structure of the polymer. In the case of PDMS, incubation is associated with local chemical transformations up to several hundred micrometers below the polymer surface. It is possible to study these local chemical transformations by confocal Raman microscopy, because PDMS is transparent in the visible. The domains of transformation consist of carbon and silicon, as indicated by the appearance of the carbon D- and G-bands between 1310 and 1610 cm⁻¹, a band appearing between 502 and 520 cm⁻¹ can be assigned to mono- and/or polycrystalline silicon.The ablation products, which are detected in the surroundings of the ablation crater consist of carbon and amorphous SiO_x (x ≈ 1.5) as detected by infrared spectroscopy.     

Giant fullerenes formed on C60 films irradiated with electrons field-emitted from scanning tunneling microscope tips

It has been found that spherical large clusters of carbon atoms are formed by irradiation of crystalline C₆₀ films grown on Si(1 1 1)-(7 × 7) surfaces with electrons field-emitted from a scanning tunneling microscope probe tip. The size distribution of the clusters deduced from surface profile measurements suggests that the dominant clusters were not necessarily C_60n (n = 2-4) expected from the simple fusion of C₆₀ molecules. It was proposed that electronic excitations of C₆₀ molecules caused the fragment and coalescence of the molecules to form the giant fullerenes as in the photo-induced similar effects.