Si epitaxial growth on LaAlO3(0 0 1)

We report on the growth of Si on c(2 × 2) reconstructed LaAlO₃(0 0 1) surfaces at high substrate temperature (700 °C) by molecular beam epitaxy. An initial Volmer-Weber mode is evidenced using reflection high energy electron diffraction (RHEED), X-ray photoelectron diffraction (XPD) and atomic force microscopy. After the deposition of a few monolayers, the islands coalesce. Using X-ray photoelectron spectroscopy, we demonstrate that Si islands exhibit an abrupt interface with the LaAlO₃ substrate without formation of silicate or silica. Finally, combined RHEED and XPD measurements show the epitaxial growth of Si with a unique Si(0 0 1)//LaAlO₃(0 0 1) and Si<1 0 0>//LAO<1 1 0> relationship.     

Bimodal growth of manganese silicide on Si(1 0 0)

Two different growth modes of manganese silicide are observed on Si(1 0 0) with scanning tunneling microscopy. 1.0 and 1.5 monolayer Mn are deposited at room temperature on the Si(1 0 0)-(2 × 1) substrate. The as-grown Mn film is unstructured. Annealing temperatures between room temperature and 450 °C lead to small unstructured clusters of Mn or Mn_xSi_y. Upon annealing at 450 °C and 480 °C, Mn reacts chemically with the Si substrate and forms silicide islands. The dimer rows of the substrate become visible again. Two distinct island shapes are found and identified as MnSi and Mn₅Si₃.     

Growth of (√3 × √3)-Ag and (1 1 1) oriented Ag islands on Ge/Si(1 1 1) surfaces

We have studied the growth of Ag on Ge/Si(1 1 1) substrates. The Ge/Si(1 1 1) substrates were prepared by depositing one monolayer (ML) of Ge on Si(1 1 1)-(7 × 7) surfaces. Following Ge deposition the reflection high energy electron diffraction (RHEED) pattern changed to a (1 × 1) pattern. Ge as well as Ag deposition was carried out at 550 °C. Ag deposition on Ge/Si(1 1 1) substrates up to 10 ML has shown a prominent (√3 × √3)-R30° RHEED pattern along with a streak structure from Ag(1 1 1) surface. Scanning electron microscopy (SEM) shows the formation of Ag islands along with a large fraction of open area, which presumably has the Ag-induced (√3 × √3)-R30° structure on the Ge/Si(1 1 1) surface. X-ray diffraction (XRD) experiments show the presence of only (1 1 1) peak of Ag indicating epitaxial growth of Ag on Ge/Si(1 1 1) surfaces. The possibility of growing a strain-tuned (tensile to compressive) Ag(1 1 1) layer on Ge/Si(1 1 1) substrates is discussed.     

Stranski-Krastanov like oxide growth on Ag(1 1 1) at atmospheric oxygen pressures

The oxidation behavior of Ag(1 1 1) was studied by means of in situ surface X-ray diffraction at atmospheric oxygen pressure. Exposure to 1 bar oxygen at 773 K reveals a competing growth of three different oxygen-induced structures on Ag(1 1 1), namely the well-known p(4 × 4) reconstruction, a surface oxide in a p(7 × 7) coincidence structure and the bulk oxide Ag₂O in orientation. The latter two exhibit the same honeycomb on hexagon arrangement of the Ag sublattice with respect to the Ag(1 1 1) surface. An inverted stacking of Ag planes in the bulk oxide islands is observed as compared to the Ag(1 1 1) substrate, which sheds new light on the Ag₂O formation process. Finally, we present a structural model of the p(7 × 7) reconstruction, based on a three-layer O-Ag-O slab of Ag₂O(1 1 1).     

Electron and lattice structure of ultra thin Ag films on Si(1 1 1) and Si(0 0 1)

We studied the low temperature (T ? 130 K) growth of Ag on Si(0 0 1) and Si(1 1 1) flat surfaces prepared by Si homo epitaxy with the aim to achieve thin metallic films. The band structure and morphology of the Ag overlayers have been investigated by means of XPS, UPS, LEED, STM and STS. Surprisingly a (√3 × √3)R30° LEED structure for Ag films has been observed after deposition of 2-6 ML Ag onto a Si(1 1 1)(√3 × √3)R30°Ag surface at low temperatures. XPS investigations showed that these films are solid, and UPS measurements indicate that they are metallic. However, after closer STM studies we found that these films consists of sharp Ag islands and (√3 × √3)R30°Ag flat terraces in between. On Si(0 0 1) the low-temperature deposition yields an epitaxial growth of Ag on clean Si(0 0 1)-2 × 1 with a twinned Ag(1 1 1) structure at coverage’s as low as 10 ML. Furthermore the conductivity of few monolayer Ag films on Si(1 0 0) surfaces has been studied as a function of temperature (40-300 K).     

Formation of strontium template on Si(1 0 0) by atomic layer deposition

The formation of ordered Sr overlayers on Si(1 0 0) by Atomic Layer Deposition (ALD) from bis(triisopropylcyclopentadienyl) Strontium (Sr(C₅ⁱPr₃H₂)₂) and H₂O has been investigated. SrO overlayers were deposited on a 1-2 nm SiO₂/Si(1 0 0) substrate, followed by a deoxidation process to remove the SiO₂ layer at high temperatures. Auger electron spectroscopy, Rutherford backscattering spectrometry, spectroscopic ellipsometry, and low-energy electron diffraction were used to investigate the progress of both ALD and deoxidation processes. Results show that an ordered Sr/Si(1 0 0) surface with 2 × 1 pattern can be obtained after depositing several monolayers of SrO on Si using ALD followed by an anneal at 800-850 °C. The (2 × 1) ordered Sr/Si(1 0 0) surface is known to be an excellent template for the epitaxial growth of SrTiO₃ (STO) oxide. The present results demonstrate that ALD is a potential alternative to molecular beam epitaxy methods for the fabrication of epitaxial oxides on semiconductor substrates.     

Interpretation of initial stage of 3C-SiC growth on Si(1 0 0) using dimethylsilane

The initial stage of cubic silicon carbide (3C-SiC) growth on a Si(0 0 1) surface using dimethylsilane (DMS) as a source gas was observed using scanning tunneling microscopy (STM) and reflection high-energy electron diffraction (RHEED). It was found that the dimer vacancies initially existing on the Si(0 0 1)-(2 × 1) surface were repaired by the Si atoms in DMS molecules, during the formation of the c(4 × 4) surface. From the STM measurement, nucleation of SiC was found to start when the Si surface was covered with the c(4 × 4) structure but before the appearance of SiC spots in the RHEED pattern. The growth mechanism of SiC islands was also discussed based on the results of RHEED, STM and temperature-programmed desorption (TPD).     

Growth of Al2O3 thin films on NiAl(1 0 0) by gas-phase oxidation and electro-oxidation

The growth and structures of aluminum oxides on NiAl(1 0 0) have been investigated by RHEED (reflection high energy electron diffraction), complemented by LEED (low energy electron diffraction), AES (Auger electron spectroscopy) and STM (scanning tunneling microscopy). Crystalline θ-Al₂O₃ phase grows through gas-phase oxidation on the NiAl(1 0 0) substrate with its a and b-axes parallel to [0 −1 0] and [0 0 1] direction of the substrate, respectively, forming a (2 × 1) unit cell. Whilst, three-dimensional nano-sized NiAl(1 0 0) protrusions and Al₂O₃, NiAl(0 1 1) clusters were found to co-exit at the surface, evidenced by extraordinary transmission spots superposed to the substrate reflection rods in the RHEED patterns. Particularly, the NiAl(0 1 1) clusters develop with their (0 1 1) plane parallel to the NiAl(1 0 0) surface, and [1 0 0] axis parallel to the [0 −1 1] direction of the substrate surface. STM observation combined with information from AES and TPD (temperature programmed desorption) suggest the formation of these 3D structures is closely associated with partial decomposition of the crystalline oxides during annealing. On the other hand, smoother (2 × 1) oxide islands with thickness close to a complete monolayer of θ-Al₂O₃ can be formed on NiAl(1 0 0) by electro-oxidation, in contrast with the large crystalline films formed by gas-oxidation.     

Influence of the surface-termination of hexagonal SiC(0 0 0 1) on the temperature dependences of Ge growth modes and desorption

With the aim of comparing initial Ge adsorption and desorption modes on different surface terminations of 4H-SiC(0 0 0 1) faces, 3 × 3, √3×√3R30° (R3) and 6√3×6√3R30° (6R3) reconstructions, of decreasing Si surface richness, have been prepared by standard surface preparation procedures. They are controlled by reflection high energy electron diffraction (RHEED), low energy electron diffraction and photoemission. One monolayer of Ge has been deposited similarly at room temperature on each of these three surfaces, followed by the same set of isochronal heatings at increasing temperatures up to complete Ge desorption. At each step of heating, the structural and chemical status of the Ge ad-layer has been probed. Marked differences between the Si- (3 × 3 and R3) and C-rich (6R3) terminations have been obtained. Ge wetting layers are only obtained up to 400 °C on 3 × 3 and R3 surfaces in the form of a 4 × 4 reconstruction. The wetting is more complete on the R3 surface, whose atomic structure is the closest to an ideally Si-terminated 1 × 1 SiC surface. At higher temperatures, the wetting layer stage transiets in Ge polycrystallites followed by the unexpected appearance on the 3 × 3 surface of a more ordered Si island structure. It denotes a Si clustering of the initial Si 3 × 3 excess, induced by the presence of Ge. A phase separation mechanism between Si and Ge prevails therefore over alloying by Ge supply onto a such Si-terminated 3 × 3 surface. Conversely, no wetting is obtained on the 6R3 surface and island formation of exclusively pure Ge takes place already at low temperature. These islands exhibit a better epitaxial relationship characterized by Ge(1 1 1)//SiC(0 0 0 1) and Ge〈1 1 −2〉//SiC〈1 −1 0 0〉, ascertained by a clear RHEED spot pattern. The absence of any Ge-C bond signature in the X-ray photoelectron spectroscopy Ge core lines indicates a dominant island nucleation on heterogeneous regions of the surface denuded by the 6R3 graphite pavings. Owing to the used annealing cycles, the deposited Ge amount desorbs on the three surfaces at differentiated temperatures ranging from 950 to 1200 °C. These differences probably reflect the varying morphologies formed at lower temperature on the different surfaces. Considering all these results, the use of imperfect 6R3 surfaces appears to be suited to promote the formation of pure and coherent Ge islands on SiC.     

Atypical grain growth for (2 1 1) CdTe films deposited on surface reconstructed (1 0 0) SrTiO3 substrates

The (1 0 0) SrTiO₃ substrate has emerged as the oxide substrate of choice for the deposition of a wide variety of materials. The substrate's unavoidable miscut leads to a step-terrace morphology when heated to high temperatures. This morphological transition is accompanied by an atomic scale repositioning of the uppermost terrace atoms, the nature of which is strongly dependent on the substrate temperature and ambient atmosphere used. Here, we report the deposition of CdTe films on the as-received and reconstructed surfaces of (1 0 0) SrTiO₃. The as-received substrate gives rise to a [1 1 1] CdTe film with four equally distributed in-plane grain orientations. The surface reconstruction, on the other hand, gives rise to an unprecedented reorientation of the film's grain structure. For this case, a [2 1 1] CdTe film emerges having twelve unevenly distributed in-plane orientations. We attribute the film's grain structure to an atomic scale surface reconstruction, with the anisotropic distribution of grain-types arising from a preferential formation due to the step edges.     

Observation of Si(1 0 0) surfaces annealed in hydrogen gas ambient by scanning tunneling microscopy

We investigated the cleaning process of Si(1 0 0) surfaces by annealing in H₂ gas ambient following chemical treatments by scanning tunneling microscopy. We observed the monohydride Si structure: Si(1 0 0):2 × 1-H on the surfaces annealed at 1000 °C in 2.5 × 10⁴ Pa H₂ gas ambient without conspicuous contaminants. On the sample annealed for 10 min or longer times, well-defined Si(1 0 0) structures with alternating S_A and S_B steps were observed, whereas the initial roughness still remained on the surfaces annealed for only 5 min.     

Surface treatments toward obtaining clean GaN(0 0 0 1) from commercial hydride vapor phase epitaxy and metal-organic chemical vapor deposition substrates in ultrahigh vacuum

We studied processes of cleaning GaN(0 0 0 1) surfaces on four different types of wafers: two types were hydride vapor phase epitaxy (HVPE) free-standing substrates and two types were metal-organic chemical vapor deposition (MOCVD) films grown on these HVPE substrates and prepared by annealing and/or Ar ion sputtering in ultra high vacuum. We observed the surfaces through treatments using in situ low-energy electron diffraction (LEED), reflection high-energy electron diffraction (RHEED), scanning tunneling microscopy (STM), and Auger electron spectroscopy, and also using ex situ temperature programmed desorption, X-ray photoelectron spectroscopy, X-ray diffraction, and secondary ion mass spectrometry. For HVPE samples, we obtained relatively clean surfaces under optimized three-step annealing conditions (200 °C for 12 h + 400 °C for 1 h + 500 °C for 5 min) without sputtering, after which the surface contamination of oxide and carbide was reduced to ∼20% of that before annealing. Clear GaN(0 0 0 1)1×1 patterns were obtained by LEED and RHEED. STM images showed flat terraces of ∼10 nm size and steps of ∼0.5 nm height. Upon annealing the HVPE-GaN samples at a much higher temperature (C), three-dimensional (3D) islands with facets were formed and the surface stoichiometry was broken down with the desorption of nitrogen in the form of ammonia, since the samples include hydrogen as an impurity. Ar⁺ sputtering was effective for removing surface contamination, however, postannealing could not recover the surface roughness but promoted the formation of 3D islands on the surface. For MOCVD/HVPE homoepitaxial samples, the surfaces are terminated by hydrogen and the as-introduced samples showed a clear 1×1 structure. Upon annealing at 500-600 °C, the surface hydrogen was removed and a 3×3 reconstruction structure partially appeared, although a 1×1 structure was dominant. We summarize the structure differences among the samples under the same treatment and clarify the effect of crystal quality, such as dislocations, the concentration of hydrogen impurities, and the residual reactant molecules in GaN films, on the surface structure.     

Pd adsorption on Si(1 1 3) surface: STM and XPS study

Pd-induced surface structures on Si(1 1 3) have been studied by scanning tunneling microscopy (STM) and X-ray photoelectron spectroscopy (XPS). In the initial process of the Pd adsorption below 0.10 ML, Pd silicide (Pd₂Si) clusters are observed to form randomly on the surface. By increasing the Pd coverage to 0.10 ML, the clusters cover the entire surface, and an amorphous layer is formed. After annealing the Si(1 1 3)-Pd surface at 600 °C, various types of islands and chain protrusions appears. The agglomeration, coalescence and crystallization of these islands are observed by using high temperature (HT-) STM. It is also found by XPS that the islands correspond to Pd₂Si structure. On the basis of these results, evolution of Pd-induced structures at high temperatures is in detail discussed.     

Surfactant effect of Sb on the growth of MnSi1.7 layers on Si(0 0 1)

Deposition of one monolayer of Sb prior to the deposition of Mn at 600 °C is observed to increase the MnSi_1.7 island density by about two orders of magnitude as well as to change the crystalline orientation of the silicide grains. The preferential epitaxial orientation of MnSi_1.7 grains grown by this process is determined to be MnSi_1.7(1 0 0)[0 1 0]||Si(0 0 1)[1 0 0]. This growth procedure results in the silicide growth into the Si matrix. For comparison, the same deposition process carried out without Sb leads to silicide formation on top of the substrate surface. The observed morphological changes of the MnSi_1.7 layers can be explained by a reduced surface diffusion of the Mn atoms on Si(0 0 1) in presence of the Sb monolayer. Additionally, lateral Si diffusion is considered to be nearly suppressed, which is responsible for the observed silicide growth into the substrate.     

Hydrogen adsorption on GaAs(0 0 1)-c(4 × 4)

Exposure of the As-terminated GaAs(0 0 1)-c(4 × 4) reconstructed surface to atomic hydrogen (H) at different substrate temperatures (50-480 °C) has been studied by reflection high-energy electron diffraction (RHEED) and scanning tunnelling microscopy (STM). Hydrogen exposure at low temperatures (∼50 °C) produces a disordered (1 × 1) surface covered with AsH_x clusters. At higher temperatures (150-400 °C) exposure to hydrogen leads to the formation of mixed c(2 × 2) and c(4 × 2) surface domains with H adsorbed on surface Ga atoms that are exposed due to the H induced loss of As from the surface. At the highest temperature (480 °C) a disordered (2 × 4) reconstruction is formed due to thermal desorption of As from the surface. The results are consistent with the loss of As from the surface, either through direct thermal desorption or as a result of the desorption of volatile compounds which form after reaction with H.     

Impact of O2 exposure on surface crystallinity of clean and Ba terminated Ge(1 0 0) surfaces

In analogy with the case of Sr on Si [Y. Liang, S. Gan, M. Engelhard, Appl. Phys. Lett. 79 (2001) 3591], we studied surface crystallinity and oxidation behaviour of clean and Ba terminated Ge(1 0 0) surfaces as a function of oxygen pressure and temperature. The structural and chemical changes in the Ge surface layer were monitored by LEED, XPS and real-time RHEED. In contrast to the oxidation retarding effect, observed for 1/2 monolayer of Sr on Si, the presence of a Ba termination layer leads to a pronounced increase in Ge oxidation rate with respect to clean Ge. In fact, while the Ge(1 0 0) surface terminated with 1/2 ML Ba amorphizes for a pO₂ of 10⁻² Torr, LEED indicates that clean Ge forms a thin (4.5 Å), 1 × 1 ordered oxide upon aggressive O₂ exposure (150 Torr, 200 °C, 30 min). We briefly discuss the origins for the difference in behaviour between Ba on Ge and Sr on Si.     

A structural parallel between Ge- and Si-induced 4 × 4 and 3 × 3 reconstructions on SiC(0 0 0 1) drawn from comparative RHEED oscillations

The initial Ge growth stages on a (√3 × √3)R30°-reconstructed SiC(0 0 0 1) surface (√3) have been studied using a complete set of surface techniques such as reflection high energy electron diffraction (RHEED), low energy electron diffraction (LEED), atomic force microscopy (AFM) and photoemission and compared with similar Si surface enrichments in place of Ge. The investigations essentially focus on the wetting growth-regimes that are favoured by the use of the √3 surface as a starting substrate, this surface being the closest to a smooth and ideally truncated Si-terminated face of hexagonal SiC(0 0 0 1). Depending on temperature and Ge or Si coverages, varying surface organizations are obtained. They range from unorganized layer by layer growths to relaxed Ge(1 1 1) or Si(1 1 1) island growths, through intermediate attempts of coherent and strained Ge or Si surface layers, characterized by 4 × 4 and 3 × 3 surface reconstructions, respectively. RHEED intensity oscillation recordings, as a function of Ge or Si deposited amounts, have been particularly helpful to pinpoint the limited (by the high lattice mismatch) existence domains of these interesting coherent phases, either in terms of formation temperature or surface coverages. Prominently comparable data for these two Ge- and Si-related reconstructions allow us to propose an atomic model for the still unexplained Ge-4 × 4 one. It is based on a same local organization in trimer and ad-atom units for the Ge excess as admitted for the Si-excess of the 3 × 3 surface, the higher strain nevertheless favouring arrangements, for the Ge-units, in 4 × 4 arrays instead of 3 × 3 Si ones. Admitting such models, 1.25 and 1.44 monolayers of Ge and Si, should, respectively, be able to lie coherently on SiC, with respective lattice mismatches near 30% and 25%. The experimental RHEED-oscillations values are compatible with such theoretical ones. Moreover, these RHEED coverage determinations (for layer completion, for instance) inform us in turn about the initial Si richness of the starting √3 reconstruction and help us to discriminate between earlier contradictory atomic models proposed in the literature.     

Fabrication of uniform Au silicide islands on the Si(1 1 1)-(7 × 7) substrate

The Au silicide islands have been fabricated by additional deposition of Au on the prepared surface at 270 °C where the Si islands of magic sizes were formed on the Si(1 1 1)-(7 × 7) dimer-adatom-stacking fault substrate. The surface structure on the Au silicide islands shows the Au/Si(1 1 1)-√3 × √3 reconstructed structure although the substrate remains 7 × 7 DAS structure. The size of the Au silicide islands depends on the size distribution of the preformed Si islands, because the initial size and shape of the Si islands play important roles in the formation of the Au silicide island. We have achieved the fabrication of the Au silicide islands of about the same size (∼5 nm) and the same shape by controlling the initial Si growth and the additional Au growth conditions.     

Preparation and characterization of C54 TiSi2 nanoislands on Si (1 1 1) by laser deposition of TiO2

We present the preparation of C54 TiSi₂ nanoislands on Si (1 1 1) with a method of the pulsed laser deposition of titanium oxide thin films. The TiO₂ thin films with nominal thicknesses of 1 nm on Si (1 1 1) were annealed at 850 °C for about 4 h in situ. The X-ray diffraction patterns and the X-ray photoelectron spectra indicate that the nanoislands are in C54 TiSi₂ phase. The characterization using a scanning tunneling microscope shows that the nanoislands with triangular, polygonal and rod-like shapes on Si (1 1 1) exhibit the Volmer-Weber growth mode. The sizes of the polygonal islands distribute in two separated ranges. For the small islands, they have a narrow lateral size distribution centered at 4 nm and a height range in 0.6-3.6 nm, while for the large islands, their lateral sizes are in the range of 12-40 nm and the heights in the range of 4-9 nm. The sizes of the well-shaped triangular islands are intermediate with the lateral sizes in range of 5-20 nm and the heights of 2-3.5 nm. The rod-like islands are about 50-200 nm in length, 5 nm in height and about 15-20 nm in width. The origination of the various shapes of the nanoislands is attributed to the symmetry of Si (1 1 1) substrate and the lattice mismatch between the C54 TiSi₂ and the Si (1 1 1) surface.