Effects of plasticizer and nanofiller on the dielectric dispersion and relaxation behaviour of polymer blend based solid polymer electrolytes

Solid polymer electrolytes consisted of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blend (50:50 wt/wt%) with lithium triflate (LiCF₃SO₃) as a dopant ionic salt at stoichiometric ratio [EO + (CO)]:Li⁺ = 9:1, poly(ethylene glycol) (PEG) as plasticizer (10 wt%) and montmorillonite (MMT) clay as nanofiller (3 wt%) have been prepared by solution cast followed by melt–pressing method. The X–ray diffraction study infers that the (PEO–PMMA)–LiCF₃SO₃ electrolyte is predominantly amorphous, but (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG electrolyte has some PEO crystalline cluster, whereas (PEO–PMMA)–LiCF₃SO₃–10 wt% PEG–3 wt% MMT electrolyte is an amorphous with intercalated and exfoliated MMT structures. The complex dielectric function, ac electrical conductivity, electric modulus and impedance spectra of these electrolytes have been investigated over the frequency range 20 Hz to 1 MHz. These spectra have been analysed in terms of the contribution of electrode polarization phenomenon in the low frequency region and the dynamics of cations coordinated polymer chain segments in the high frequency region, and also their variation on the addition of PEG and MMT in the electrolytes. The temperature dependent dc ionic conductivity, dielectric relaxation time and dielectric strength of the plasticized nanocomposite electrolyte obey the Arrhenius behaviour. The mechanism of ions transportation and the dependence of ionic conductivity on the segmental motion of polymer chain, dielectric strength, and amorphicity of these electrolytes have been explored. The room temperature ionic conductivity values of the electrolytes are found ∼10⁻⁵ S cm⁻¹, confirming their use in preparation of all-solid-state ion conducting devices.     

Effect of nanofillers on thermal and transport properties of potassium iodide–polyethylene oxide solid polymer electrolyte

In order to enhance the ionic conductivity of polyethylene oxide (PEO)–KI(80:20) based alkaline polymer electrolytes, nanosized inorganic filler ZnS has been incorporated into PEO–KI matrix and the corresponding nanocomposite polymer electrolytes are synthesized by the usual solution casting procedure. Atomic force microscope image of composite polymer electrolyte exhibits that the introduction of ZnS nanoparticles changes the surface morphology and aggregates them to form an arborization pattern. The prepared nanocomposite polymer electrolyte reveals an ionic conductivity of about 10^?4 S cm^?1 for 5 wt% ZnS at room temperature.     

Effects of Al2O3 nanofiller and EC plasticizer on the ionic conductivity enhancement of solid PEO-LiCF3SO3 solid polymer electrolyte

A solid polymer electrolyte (SPE) is synthesized by solution casting technique. The SPE uses poly(ethylene oxide) PEO as a host matrix doped with lithium triflate (LiCF₃SO₃), ethylene carbonate (EC) as plasticizer and nano alumina (Al₂O₃) as filler. The polymer electrolytes are characterized by Impedance Spectroscopy (IS) to determine the composition of the additive which gives the highest conductivity for each system. At room temperature, the highest conductivity is obtained for the composition PEO-LiCF₃SO₃-EC-15%Al₂O₃ with a value of 5.07 10^− 4 S/cm. The ionic conductivity of the polymer electrolytes increases with temperature and obeys the Arrhenius law. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) studies indicate that the conductivity increase is due to an increase in amorphous content which enhances the segmental flexibility of polymeric chains and the disordered structure of the electrolyte. Fourier transform infrared spectroscopy (FTIR) spectra show the occurrence of complexation and interaction among the components. Scanning electron microscopy (SEM) images show the changes morphology of solid polymer electrolyte.     

Influence of solid electrolyte particles size on ionic transport in model composite system (PVdF-HFP–Li1.3Al0.3Ti1.7(PO4)3)

The influence of filler particles size on lithium ion conductivity of composite polymer electrolytes was issued on model system vinylidenefluoride with hexafluoropropylene (PVdF-HFP)–Li_1.3Al_0.3Ti_1.7(PO₄)₃. Model electrolyte objects with filler grains of different sizes were prepared using a modified solvent casting method from a mixture of PVdF-HFP solution in dimethylformamide and Li_1.3Al_0.3Ti_1.7(PO₄)₃ solid electrolyte particles. The percolation threshold was defined and the transport properties of composite polymer electrolytes at different volume concentrations of the solid electrolyte investigated. A significant decrease in conductivity compared to that of ceramic solid electrolytes was observed. The size of the filler particles was found to affect the structure and transport properties of the prepared composite polymer electrolytes. The conductivity of the composite polymer electrolyte at 100 °C was found to increase by two orders of magnitude with the tenfold increase of the size of the filler particles.     

Combined effect of nanochitosan and succinonitrile on structural, mechanical, thermal, and electrochemical properties of plasticized nanocomposite polymer electrolytes (PNCPE) for lithium batteries

A sequence of novel plasticized polymer nanocomposite electrolyte systems based on polyethylene oxide (PEO) as polymer host, LiCF₃SO₃ as salt, and a variety of concentrations of nanochitosan as inert filler, succinonitrile as a solid non-ionic plasticizer has been prepared. The prepared membranes were subjected to X-ray diffraction, FT-IR, tensile strength, morphological studies, thermal analysis, AC ionic conductivity measurement, and interfacial analyses. The combined effect of succinonitrile and nanochitosan on the electrochemical properties of polymer electrolytes has been studied, and it was confirmed that the ionic conductivity is significantly increased. The maximum ionic conductivity of the plasticized nanocomposite polymer electrolytes are found to be in the range of 10^?2.8?S/cm. Besides, the interfacial stability also shows a significant improvement. The tensile measurement and thermal analysis results illustrate that the electrolytes based on that polymer host possess good mechanical and thermal stabilities.     

Study on ionic conductivity and dielectric properties of PEO-based solid nanocomposite polymer electrolytes

The ionic conductivity and dielectric properties of the solid nanocomposite polymer electrolytes formed by dispersing a low particle-sized TiO₂ ceramic filler in a poly (ethylene oxide) (PEO)-AgNO₃ matrix are presented and discussed. The solid nanocomposite polymer electrolytes are prepared by hot press method. The optimum conducting solid polymer electrolyte of polymer PEO and salt AgNO₃ is used as host matrix and TiO₂ as filler. From the filler concentration-dependent conductivity study, the maximum ionic conductivity at room temperature is obtained for 10 wt% of TiO₂. The real part of impedance (Z′) and imaginary part of impedance (Z″) are analyzed using an LCR meter. The dielectric properties of the highest conducting solid polymer electrolyte are analyzed using dielectric permittivity (ε′), dielectric loss (ε″), loss tangent (tan δ), real part of the electric modulus (M′), and imaginary part of the electric modulus (M″). It is observed that the dielectric constant (ε′) increases sharply towards the lower frequencies due to the electrode polarization effect. The maxima of the loss tangent (tan δ) shift towards higher frequencies with increasing temperature. The peaks observed in the imaginary part of the electric modulus (M″) due to conductivity relaxation shows that the material is ionic conductor. The enhancement in ionic conductivity is observed when nanosized TiO₂ is added into the solid polymer electrolyte.     

Electrochemical performance of plasticized PEO-LiTf complex-based composite gel polymer electrolytes with the addition of barium titanate

Gel electrolytes and solid electrolytes have been reported as a potential element to slow down the polysulfide shuttle by reducing its mobility in the electrolytes. The preparation of sulfur-conductive polymer composites, or sulfur-carbon composites, has been reported as softening the impact of the shuttle effects. Unlike Li-ion batteries so far, no electrolyte is found to be optimal for Li–S batteries at all conditions. Taking into account all these factors, in the present study, an attempt has been made to develop solid polymer electrolytes in conjunction with non-aqueous liquid electrolytes along with inert fillers for Li–S batteries. Poly-ethylene oxide (PEO)-based composite gel polymer electrolytes (CGPE) comprising a combination of plasticizers, namely 1,3-dioxolane (DIOX)/tetraethylene glycol dimethylether (TEGDME) and a lithium salt (LiTf) with the addition of ceramic filler, barium titanate (BaTiO₃) have been prepared using a simple solution casting technique in an argon atmosphere. The as-prepared polymer electrolyte films were subjected to SEM, ionic conductivity, TG/DTA, and FTIR analyses. A symmetric cell composed of Li/CGPE/Li was assembled, and the variation of interfacial resistance as a function of time was also measured. The ionic conductivity was found to be increased as a function of temperature. The lithium transference number (Li_t ⁺) was measured, and the value was calculated as 0.7 which is sufficient for battery applications. The electrochemical stability window of the sample was studied by linear sweep voltammetry, and the polymer electrolyte film was found to be stable up to 5.7 V. The TG/DTA analysis reveals that this CGPE is thermally stable up to 350 °C. The compatibility studies exhibited that CGPE has better interracial properties with lithium metal anode. The interaction between the PEO and salt has been identified by an FTIR analysis.     

Nano-composite solid polymer electrolytes for solid state ionic devices

Recent research efforts to improve the ambient temperature conductivity in polyethylene oxide (PEO) based solid polymer electrolytes have been directed towards the incorporation of ultra-fine nano-sized particles of ceramic fillers such as Al₂O₃, γ-LiAlO₂, SiO₂ and TiO₂ into the polymer electrolyte. In these PEO based nano-composite polymer electrolytes, conductivity enhancements of up to two orders of magnitude have been achieved. Thermal, electrical conductivity and dielectric relaxation measurements performed on several nano-composite polymer electrolyte systems have shown that the degree of enhancement depends primarily on the grain size. In this paper, results of three nano-composite polymer electrolyte systems, PEO:LiTFSI:Al₂O₃, PEO:LiTf:Al₂O₃ and PEO:LiTf: SiO₂ are discussed as representative examples. It is suggested that the conductivity enhancement is due to the creation of additional sites and favourable conduction pathways for ionic transport through Lewis acidbase type interactions between the filler surface groups (H/OH) and the ionic species. Paper presented at the 2nd International Conference on Ionic Devices, Anna University, Channai, India, Nov. 28–30, 2003.     

Effect of polysorbate plasticizer on the structural and ion conduction properties of PEO–NH<Subscript>4</Subscript>PF<Subscript>6</Subscript> solid polymer electrolyte

Effects of a new plasticizer, polysorbate 80, on the structural and electrochemical properties of PEO–NH₄PF₆ polymer electrolyte system have been investigated. X-ray diffraction studies show significant increase in amorphicity of the solid polymer electrolyte on introduction of the plasticizer, which is also supported by lesser-dense spherulites observed in the SEM micrographs. The room temperature ionic conductivity of the electrolyte shows an increase of about two orders of magnitude (σ_max～10^?5 S/cm) on plasticization. The frequency dependence of the conductivity has been found to obey the Jonscher’s power law and slower backward ion hopping on plasticization. The polymer electrolyte shows protonic conduction as confirmed using cyclic voltammetry study. The studies show that polysorbate 80 is a promising plasticizer for semicrystalline polymer electrolytes.     

Structural and thermal studies of [PVA–LiAc] : TiO2 polymer nanocomposite system

Nanocomposite polymer electrolyte consisting of polyvinyl alcohol (PVA) and lithium acetate with TiO₂ filler has been synthesised by combination of solution cast technique and sol–gel process. The composite electrolyte films were characterised by different experimental techniques. The average particle size of composite electrolytes lies between 25 and 30?nm. System is essentially ionic with maximum conductivity of polymer electrolyte 90[80PVA–20LiAc]:10TiO₂ (～4.5?×?10^?6?S?cm^?1) at room temperature.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Effect of thermal history and characterization of plasticized,composite polymer electrolyte based on PEO and tetrapropylammonium iodide salt (Pr4N+I-)

The search for anionic conductors based on solid polymer electrolytes is important for the development of photo-electrochemical (PEC) solar cells due to their many favourable chemical and physical properties. Although solid polymer electrolytes have been extensively studied as cation, mainly lithium ion, conductors for applications in secondary batteries, their use as anionic conductors have not been studied in greater detail. In a previous paper we reported the application of a PEO based iodide ion conducting electrolyte in a PEC solar cell. This electrolyte had the composition PEO: Pr₄N⁺I^? = 9:1 with 50 wt.% ethylene carbonate (EC). In this work we have studied the effect of incorporating alumina filler on the properties of this electrolyte. The investigation was extended to electrical and dielectric measurements including high frequency impedance spectroscopy and thermal analysis.In the DSC themograms two endothermic peaks have been observed on heating, one of these peaks is attributed with the melting of the PEO crystallites, while the other peak with a melting temperature ~ 30 °C is attributed to the melting of the EC rich phase. The melting temperature of both these peaks shows a marked variation with alumina content in the electrolyte. The temperature dependence of the conductivity shows that there is an abrupt conductivity increase in the first heating run evidently due to the melting of the EC rich phase. High conductivity values are retained at lower temperatures in the second heating. Conductivity isotherms show the existence of two maxima, one at ~ 5% Al₂O₃ content and the other at ~ 15%. The occurrence of these two maxima has been explained in terms of the interactions caused by alumina grains, the crystallinity and melting of the PEO rich phase. As seen from latent heat of melting, the crystallinity of the electrolyte has reduced considerably during the first heating run. In contrast to the conductivity enhancement caused by ceramic fillers in PEO-based cation containing electrolytes, no conductivity enhancement has been observed in the present PEO based anionic conducting materials by adding alumina except at low temperatures.     

An experimental study on the effect of mesoporous silica addition on ion conductivity of poly(ethylene oxide) electrolytes

Solid polymer electrolyte (SPE) composites, which are composed of poly(ethylene oxide) (PEO), mesoporous silica (SBA-15), and lithium salt were prepared in order to investigate the influence of SBA-15 content on the ionic conductivity of the composites. The ionic conductivity of the SPE composites was monitored by frequency response analyzer (FRA), and the crystallinity of the SPE composites was evaluated by using XRD. As a result, the addition of SBA-15 to the polymer mixture inhibited the growth of PEO crystalline domain, due to the mesoporous structure of the SBA-15. Also, the PEO₁₆LiClO₄/SBA-15 composite electrolytes show an increased ion conductivity as a function of SBA-15 content up to 15 wt.%. These ion conductivity characteristics are dependent on crystallinity with SBA-15 content.     

发射FTIR光谱技术在聚合物电解质导电机制研究中的应用

运用发射FTIR光谱技术,实时监测SBA-15掺杂制备的复合聚合物电解质随温度升高其结晶状态变化的规律,结合电化学和SEM研究结果分析了无机填料对离子电导率的影响,并初步提出离子导电增强的机制。文章将为发射FTIR光谱技术应用于锂电池研究进行了探索。     

Mesoporous silica (MCM-41) effect on (PEO + LiAsF6) solid polymer electrolyte

Composite polymer electrolyte films consisting of polyethylene oxide (PEO), LiAsF₆ and mesoporous silica (MCM-41) with fixed PEO/LiAsF₆ = 90/10 but different weight percent ratios of MCM-41 were prepared using the solution casting method. The polymer electrolyte films were characterized using XRD, DSC, SEM and electrical impedance spectroscopy. In corporation of MCM-41 in a (PEO + LiAsF₆) polymer electrolyte facilitates salt dissociation, enhances ion conductivity, and improves miscibility between organic and inorganic moieties. The scanning electron microscopy (SEM) photographs indicates the electrolytes are miscible and homogeneous up to 10 wt.% of MCM-41, and an optimized conductivity is found at this composition (10 wt.%). However, at higher weight ratios (>10 wt.%), the Li/MCM-41-rich domain developed, and the conductivity decreased with increasing mesoporous material. The electrochemical performance of fabricated electrochemical cells of configuration Li/(PEO + LiAsF₆ + MCM-41)/(MoO₃ + C + PTFE) were investigated.     

Structural, conductivity, and dielectric characterization of PEO–PEG blend composite polymer electrolyte dispersed with TiO2 nanoparticles

A solid polymer electrolyte (SPE) composites consisting blend of poly(ethylene oxide) (PEO) and poly(ethylene glycol) (PEG) as the polymer host with LiCF₃SO₃ as a Li⁺ cation salt and TiO₂ nanoparticle which acts as a filler were prepared using solution-casting technique. The SPE films were characterized by X-ray diffraction and Fourier transform infrared analysis to ensure complexation of the polymer composites. Frequency-dependent impedance spectroscopy observation was used to determine ionic conductivity and dielectric parameters. Ionic conductivity was found to vary with increasing salt and filler particle concentrations in the polymer blend complexes. The optimum ambient temperature conductivity achieved was 2.66?×?10^?4?S?cm^?1 for PEO (65 %), PEG (15 %), LiCF₃SO₃ (15 %), ethylene carbonate (5 %), and TiO₂ (3 %) using weight percentage. The dielectric relaxation time obtained from a loss tangent plot is fairly consistent with the conductivity studies. Both Arrhenius and VTF behaviors of all the composites confirm that the conductivity mechanism of the solid polymer electrolyte is thermally activated.     

Effects of MnO<Subscript>2</Subscript> nano-particles on the conductivity of PMMA-PEO-LiClO<Subscript>4</Subscript>-EC polymer electrolytes

Li-ion rechargeable batteries based on polymer electrolytes are of great interest for solid state electrochemical devices nowadays. Many studies have been carried out to improve the ionic conductivity of polymer electrolytes, which include polymer blending, incorporating plasticizers and filler additives in the electrolyte systems. This paper describes the effects of incorporating nano-sized MnO₂ filler on the ionic conductivity enhancement of a plasticized polymer blend PMMA–PEO–LiClO₄–EC electrolyte system. The maximum conductivity achieved is within the range of 10⁻³ S cm⁻¹ by optimizing the composition of the polymers, salts, plasticizer, and filler. The temperature dependence of the polymer conductivity obeys the VTF relationship. DSC and XRD studies are carried out to clarify the complex formation between the polymers, salts, and plasticizer.     

Conductivity studies on PEO:NaClO3 electrolyte system with different plasticizers

A new ion conducting solid polymer electrolyte thin film based on Polyethylene oxide (PEO) with NaClO₃ salt is prepared by solution-casting method. The solvation of salt with PEO has been confirmed by X-ray diffraction and IR spectral studies. Plasticizer effects were studied in PEO:NaClO₃ system by using low molecular weight polyethylene glycol (PEG), dimethyl formamide (DMF) and propylene carbonate(PC). AC conductivity in the temperature range (308–378 K) was measured to evaluate the conductivity of the polymer electrolytes. From the conductivity data, it was found that the conductivity value of pure PEO increases 10²–10⁴ order of magnitude with the addition of salts as well as plasticizers. From the transference number experiments, it was confirmed that the charge transport in these electrolyte is mainly due to the ions (t_ion≈0.94). Finally, the conductivity value of all PEO: NaClO₃ systems were compared.     

Transport, structural and thermal studies on nanocomposite polymer blend electrolytes for Li-ion battery applications

Nanocomposite polymer electrolytes (NCPEs) composed of poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-co-HFP) as a host polymer, Poly(vinyl acetate) (PVAc) as an additive, Ethylene Carbonate (EC) as a plasticizer, Lithium Perchlorate as dopant salt and Barium Titanate (BaTiO₃) as a filler were prepared for various concentrations of BaTiO₃ using solvent casting technique. Thermal stability of the sample having maximum ionic conductivity was found using TG/DTA analysis. Nano composite polymer electrolytes were subjected to ac impedance analysis spectra for acquiring the ionic conductivity values at different temperature. Surface structure of the sample was analysed using scanning electron microscope and the complexations of samples were analysed using X-ray diffraction analysis. It was noted that the polymer electrolyte contains 8 wt. % of BaTiO₃ showed maximum ionic conductivity than the other ratios of BaTiO₃.