Poly(alkylthio‐p‐phenylenevinylene): Synthesis and electroluminescent and photovoltaic properties

Two alkylthio‐substituted poly(p‐phenylenevinylene) (AT–PPV) derivatives, poly(2‐octylthio‐p‐phenylenevinylene) (OT–PPV) and poly[5‐methoxy‐2‐(2′‐ethyl‐hexylthio)‐p‐phenylenevinylene] (MEHT–PPV), were synthesized by a Heck coupling reaction for the investigation of the effect of alkylthio groups on the optoelectronic properties of poly(p‐phenylenevinylene) derivatives. The absorption peaks of OT–PPV and MEHT–PPV solutions were located at 431 and 438 nm, respectively. As for solid films, an OT–PPV film showed an absorption maximum wavelength at 444 nm, 13 nm redshifted in comparison with its solution value, whereas an MEHT–PPV film displayed the same absorption peak position as its dilute solution; this indicated that there was no interchain interaction in the MEHT–PPV film. Polymeric light‐emitting diodes (PLEDs) and polymer solar cells (PSCs) based on OT–PPV and MEHT–PPV were fabricated and characterized. Very narrow bandwidths of the electroluminescence (EL) spectra of the two AT–PPVs were found, with the full width at half‐maximum of the emission being 40 and 47 nm for OT–PPV and MEHT–PPV, respectively. The maximum EL efficiency of the single‐layer PLED based on MEHT–PPV with Al as a cathode reached 1.49 cd/A. The PSC based on a blend of OT–PPV and [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) showed the power conversion efficiency of 1.4% under the illumination of AM1.5 (80 mW/cm²). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1279–1290, 2006     

Renewable resource‐based poly (m‐phenylenevinylene)s and their statistical copolymers: Synthesis,characterization, and probing of molecular aggregation and Forster energy transfer processes

We report a novel poly (m‐phenylenevinylene)s and their copolymers based on renewable resource starting material 3‐pentadecylphenol to trace the Forster energy transfer process and molecular aggregation in the π‐conjugated polymers. The new bisylide monomer was polymerized with bisaldehyde (or benzaldehyde) under Wittig‐Horner reaction conditions to prepare poly [(4‐methoxy‐6‐pentadecyl‐1, 3‐phenylenevinylene)‐alt‐(1, 3‐phenylenevinylene)] (m‐PPV) and its para‐counterpart poly [(4‐methoxy‐6‐pentadecyl‐1, 3‐phenylenevinylene)‐alt‐(1, 4‐phenylenevinylene)] (p‐PPV) and oligo‐phenylenevinylene model compound 4‐methoxy‐6‐pentadecyl‐1, 3‐distyrylbenzene (OPV). A series of with m‐ or p‐conjugated segments were also prepared by varying the m‐ and p‐content from 0 to 100% in the feed. The selective excitation of m‐conjugated segments in the copolymer by 310 nm light showed emission properties of pure p‐conjugated segments indicating the efficient Forster energy transfer process in segmented copolymers. Both solution quantum yields and the emission intensities increase up to 75% of para‐content in the copolymers. In the solid state, the increase in the p‐incorporation in the copolymer decreases the photoluminescent intensity almost by four times as compared to that of pure meta‐substituted PPV. The excitation spectra of the polymers confirmed a new peak at 400 nm corresponding to the aggregated polymer chains in the film, which is absent in the solution. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3241–3256, 2008     

Synthesis and electrochemical and electroluminescent properties of N‐phenylcarbazole‐substituted poly(p‐phenylenevinylene)

An N‐phenylcarbazole‐containing poly(p‐phenylenevinylene) (PPV), poly[(2‐(4′‐carbazol‐9‐yl‐phenyl)‐5‐octyloxy‐1,4‐phenylenevinylene)‐alt‐(2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylenevinylene)] (Cz‐PPV), was synthesized, and its optical, electrochemical, and electroluminescent properties were studied. The molecular structures of the key intermediates, the carbazole‐containing boronic ester and the dialdehyde monomer, were crystallographically characterized. The polymer was soluble in common organic solvents and exhibited good thermal stability with a 5% weight loss at temperatures above 420 °C in nitrogen. A cyclic voltammogram showed the oxidation peak potentials of both the pendant carbazole group and the PPV main chain, indicating that the hole‐injection ability of the polymer would be improved by the introduction of the carbazole‐functional group. A single‐layer light‐emitting diode (LED) with a simple configuration of indium tin oxide (ITO)/Cz‐PPV (80 nm)/Ca/Al exhibited a bright yellow emission with a brightness of 1560 cd/m² at a bias of 11 V and a current density of 565 mA/cm². A double‐layer LED device with the configuration of ITO/poly(3,4‐ethylenedioxy‐2,5‐thiophene):poly (styrenesulfonic acid) (60 nm)/Cz‐PPV (80 nm)/Ca/Al gave a low turn‐on voltage at 3 V and a maximum brightness of 6600 cd/m² at a bias of 8 V. The maximum electroluminescent efficiency corresponding to the double‐layer device was 1.15 cd/A, 0.42 lm/W, and 0.5%. The desired electroluminescence results demonstrated that the incorporation of hole‐transporting functional groups into the PPVs was effective for enhancing the electroluminescent performance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5765–5773, 2005     

A Platform for Preparation of Monodispersed Fluorescent Conjugated Polymer Microspheres with Core‐Shell Structures

A strategy to prepare stable monodispersed fluorescent microspheres is developed by modifying the Wessling method to synthesize poly(p‐phenylenevinylene) (PPV) on the surface of a highly crosslinked polymer core. The positively charged PPV polymer precursors (pre‐PPV) are adsorbed onto the core with negative charges on the surface and then the insoluble fluorescent PPVs form after thermal elimination. Each individual sphere is found to possess a very smooth surface with an even distribution of fluorescence by microscopic techniques. Very small coefficient of variance (CV) values of emission intensity (<4.0%) and size (<2.3%) are realized for microspheres prepared in the same batch. The spheres are demonstrated to have good thermal stability and photostability.     

Synthesis and double doping behavior of a poly(p‐phenylenevinylene)s bearing conjugated side chains

A poly(p‐phenylenevinylene) derivative bearing conjugated side chains (polyCPV) was synthesized by Migita‐Kosugi‐Stille type coupling polycondensation reaction. This polymer contains phenylenevinylene units in both the main chain and the side chains. UV–vis absorption and fluorescence emission spectroscopies revealed a well‐developed π‐conjugation of the polyCPV. The absorption band of the polymer was extended to long wavelengths. A fluorescent emission maximum of polyCPV is located at considerably longer wavelengths than that of the conjugated side chain monomer. Electron spin resonance measurements of polyCPV confirmed generation of charge species in both the main chain and the side chains via iodine doping. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Full color light‐emitting electrospun nanofibers prepared from PFO/MEH‐PPV/PMMA ternary blends

In this study, luminescence electrospun (ES) nanofibers based on ternary blends of poly(9,9‐dioctylfluoreny‐2,7‐diyl) (PFO)/poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV)/poly(methyl methacrylate) (PMMA) were prepared from chloroform solutions using a single capillary spinneret. Effects of PFO/MEH‐PPV ratio on the morphology and photophysical properties were studied while the PMMA weight percentage was fixed at 90 wt %. The morphologies of the prepared ES fibers were characterized by FE‐SEM and fluorescence microscopy. The obtained fibers had diameters around a few hundred nm and pore sizes in the range of 30–35 nm. The emission colors of the PFO/MEH‐PPV/PMMA blend ES fibers changed from blue, white, yellowish‐green, greenish‐yellow, orange, to yellow, as the MEH‐PPV composition increased. In contrast, the emission colors of the corresponding spin‐coated films were blue, orange, pink‐red, red, and deep‐red. Based on the values of solubility parameters, the PFO and MEH‐PPV are miscible to each other and trapped in the PMMA matrix. Hence, energy transfer between these two polymers is possible. The smaller aggregated domains in the ES fiber compared to those of spin‐coated films possibly reduce the efficiency of energy transfer, leading to different emission colors. Also, the prepared ES fibers had higher photoluminescence efficiencies than those of the spin‐coated films. Pure white light‐emitting fibers prepared from the PFO/MEH‐PPV/PMMA blend ratio of 9.5/0.5/90 had the Commission Internationale de L'Eclairage (CIE) coordinate of (0.33, 0.31). Our results showed that different color light‐emitting ES fibers were produced through optimizing the composition of semiconducting polymer in the transparent polymer matrix. This type of ES fibers could have potential applications as new light sources or sensory materials for smart textiles. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 463–470, 2009     

Poly‐p‐phenylenevinylene‐g‐poly(2‐(methacryloyloxy)Ethyl)trimethylammonium chloride (PPV‐g‐PMETAC): A fluorescent,water‐soluble,selective anion sensor

The photophysical and ion‐sensing properties of densely grafted conjugated polymer poly‐p‐phenylenevinylene‐g‐poly(2‐(methacryloyloxy)ethyl)trimethylammonium chloride (PPV‐g‐PMETAC) are presented herein. The grafted polymer exhibits excellent iodide‐sensing which is easily observed using fluorescence spectroscopy. The iodide detection limit for PPV‐g‐PMETAC was found to be 10 nM and was independent of temperature and pH <12. The change in fluorescence of PPV‐g‐PMETAC, upon exposure to iodide, was attributed to polymer aggregation due to changes in the morphology of the grafted PMETAC side chains, which was observed using atomic force microscopic and dynamic light scattering studies. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1997–2003     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004     

A solution‐processible poly(p‐phenylene vinylene) without alkyl substitution: Introducing the cis‐vinylene segments in polymer chain for improved solubility,blue emission,and high efficiency

A soluble all‐aromatic poly(2,5‐diphenyl‐1,4‐phenylenevinylene) (2,5‐DP‐PPV) is synthesized by utilizing aromatic phosphonium and aldehyde monomers through Wittig reaction. The H¹ NMR and FTIR measurements indicate that over 50% content of cis‐vinylene units exist in polymer backbone. The diphenyl‐substituted benzaldehyde monomer plays an important role to enhance cis‐products (Z‐selectivity) in Wittig reactions. The twisted cis‐segments in polymer backbone reduce the interchain interactions and enhance the solubility of such all‐aromatic PPV derivative in common organic solvents. 2,5‐DP‐PPV exhibits good solubility in common organic solvents, such as tetrahydrofuran and chloroform. The polymer film exhibits a blue light emission (λ_max = 485 nm) and a very high photoluminescence efficiency of 78%. The cis‐trans photo isomerization of this polymer in solution and the impact on the optical properties are also investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5242–5250, 2008     

Poly(p‐phenylenevinylene) presenting pendent pentaphenylene dendron groups for light‐emitting diodes

We have synthesized, using the Gilch method, a novel poly(p‐phenylenevinylene) derivative (PPV‐PP) containing two pendent pentaphenylene dendritic wedges, and have characterized its structure and properties. The incorporated side chain pentaphenylene dendrons serve as solubilizing groups, prevent π‐stacking interactions from occurring between the polymer main chains, and suppress the formation of excimers in the solid state. Photoluminescence studies indicate that efficient intramolecular energy transfer occurred from the photoexcited pentaphenylene groups to the poly(p‐phenylenevinylene) backbone. The polymer film exhibits a maximum emission at 510 nm and had a photoluminescence efficiency of 46%, which is similar to that measured in dilute solution. The photoluminescence spectra remained almost unchanged after thermal annealing at 150 °C for 20 h, and displayed inhibited excimer formation. Polymer light‐emitting diodes that we fabricated in the configuration ITO/PEDOT/PPV‐PP/Mg:Ag/Ag exhibited a maximum emission peak at 513 nm, corresponding to the green region [x = 0.30 and y = 0.62 in the Commission Internationale de L'Eclairage (CIE) chromaticity coordinates]. The maximum brightness and maximum luminance efficiency were 1562 cd/m² and 1.93 cd/A, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5147–5155, 2005     

Enhancing the electroluminescent efficiency of poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene}/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) polyblends by the introduction of chemical bonding through a thermal treatment

A significant improvement in the electroluminescence (EL) properties was observed for a poly{5‐methoxy‐2‐[(2′‐ethyl‐hexyl)‐oxy]‐p‐phenylenevinylene} (MEH–PPV)/poly(2,3‐diphenyl‐5‐octyl‐p‐phenylenevinylene) (DPO–PPV) blend after a thermal treatment at 200 °C for 2 h in vacuo to furnish the chemical bonding between polymer chains. ¹H NMR spectroscopy and two‐photon excitation microscopy revealed that the chemical bonding turned the immiscible polyblend into a system more like a block copolymer with a vertically segregated morphology. Because both the lowest unoccupied molecular orbital and highest occupied molecular orbital levels of MEH–PPV in the wetting layer were higher than those of DPO–PPV in the upper layer, the heterojunction between the two layers of the polymers fit the category of so‐called type II heterojunctions. As a result, the turn‐on voltage of the polymer light‐emitting diode prepared with the thermally treated polyblend decreased to ～0.6 V, and the EL emission intensities and quantum efficiencies increased to about 4 times those of the untreated polyblend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 62–69, 2006     

Conformational Relaxation of p‐Phenylenevinylene Trimers in Solution Studied by Picosecond Time‐Resolved Fluorescence

Two p‐phenylenevinylene (PV) trimers, containing 3′‐methylbutyloxyl (in MBOPV3) and 2′‐ethylhexyloxyl (in EHOPV3) side chains, are used as model compounds of PV‐based conjugated polymers (PPV) with the purpose of clarifying the origin of fast (picosecond time) components observed in the fluorescence decays of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV). The fluorescence decays of MBOPV3 and EHOPV3 reveal the presence of similar fast components, which are assigned to excited‐state conformational relaxation of the initial population of non‐planar trimer conformers to lower‐energy, more planar conformers. The rate constant of conformational relaxation k_CR is dependent on solvent viscosity and temperature, according to the empirical relationship k_CR=aη_o^?α?exp(?αE_η/RT), where aη_o^?α is the frequency factor, η_o is the pre‐exponential coefficient of viscosity, E_η is the activation energy of viscous flow. The empirical parameter α, relating the solvent microscopic friction involved in the conformational change to the macroscopic solvent friction (α=1), depends on the side chain. The fast component in the fluorescence decays of MEH‐PPV polymers (PPVs), is assigned to resonance energy transfer from short to longer polymer segments. The present results call for revising this assignment/interpretation to account for the occurrence of conformational relaxation, concurrently with energy transfer, in PPVs.     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Novel saturated red‐emitting poly(p‐phenylenevinylene) copolymers with narrow‐band‐gap units of 2,1,3‐benzothiadiazole synthesized by a palladium‐catalyzed Stille coupling reaction

Novel poly(p‐phenylenevinylene) (PPV) copolymers derived from 1‐methoxy‐4‐octyloxyphenylene (MOP), 2,1,3‐benzothiadiazole (BT), and trans‐1,2‐bis(tributylstannyl)ethylene were first prepared by a palladium‐catalyzed Stille coupling reaction. The feed ratios of MOP to BT were 99.5:0.5, 99:1, 95:5, 85:15, 70:30, and 50:50. An efficient energy transfer from the 2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene segment to the narrow‐band‐gap units was observed. The poly(2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene‐2,1,3‐benzothiadiazolevinylene) copolymers emitted deep red light. The maximum electroluminescence emission of these PPV copolymers occurred at 659–724 nm and was accompanied by gradual redshifting with an increasing BT concentration. The photophysical properties were examined in comparison with those of copolymers based on BT and fluorene or N‐alkylcarbazole doped with the same BT concentration in the copolymer main chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2325‐2336, 2005     

Terpyridine‐substituted,fluorescent polymers and their chelation with zinc ion: The ligand‐to‐metal ratio and optical properties

Soluble, fluorescent, terpyridine‐substituted, conjugated polymers were prepared and characterized. The polymer chains included a defined oligo(phenylenevinylene) fragment, on which the terpyridine‐functional group was attached. The polymers were blue‐fluorescent with emission peaks at 400–427 nm in tetrahydrofuran solutions. Upon chelation with the Zn(II) cation, the emission maxima were shifted to a longer wavelength by as much as 113 to 506–526 nm. A model compound was also prepared to aid the structural characterization. The ratio of terpyridine to Zn²⁺ in the polymer complex was found to be 1:1 on the basis of spectroscopic evidence, which included mass spectrometry, ¹H NMR, and Job titration. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2338–2345, 2006     

Tropone‐containing π‐conjugated polymers: Annulation of tropone onto benzene ring in the conjugated polymer

Tropone‐fused, various π‐conjugated polymers ( P2 – P5 ) were synthesized by the palladium‐catalyzed coupling reaction of 1,4‐dibromo‐6,8‐dimethyl‐7H‐benzocyclohepten‐7‐one with aromatic divinyl, diboronic acid, and diethynyl compounds. The molecular orbital calculation of the model compounds was performed to discuss effective conjugation length of the repeating unit of the polymers. The absorption spectra of phenylenevinylene‐type polymers shifted to longer wavelengths than the model compounds by about 60 nm. They exhibited green fluorescence [λ_max(em) = 544 and 561 nm]. The absorption spectrum of a phenylene‐type polymer blueshifted by 10 nm; however, that of a phenyleneethynylene‐type polymer redshifted by 83 nm as compared with their model compounds. They showed fluorescence with peak maxima at 457 and 489 nm, respectively. As a result, the absorption spectra of phenylene‐ and phenylenevinylene‐type polymers blueshifted, but that of a phenyleneethynylene‐type polymer redshifted by the annulation of tropone onto a benzene ring in the conjugated polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1208–1215, 2004     

Effect of film thickness controlled by ink‐jet printing method on the optical properties of an electroluminescent polymer

Ink‐jet printing (IJP) represents a highly promising liquid processed polymer deposition method for the film preparation of functional polymers in photo‐electronic devices. In this report, the results on the IJP of a fluorene‐based electroluminescent polymer, poly(9,9‐dihexylfluorene‐alt‐2,5‐dioctyloxybenzene) (PF6OC8), from a piezoelectric droplet generator are presented. The polymer film thickness has been found to show an approximate linear relation with the number of droplets per unit area; it is thus convenient to control the film thickness by the space of printed dots in IJP process. In comparison, spin coating approach is also used to prepare polymer films with different thicknesses by varying solution concentration and spinning speed. However, it is found that spin coating is difficult to control the film thickness quantitatively. The influence of film thickness on the photoluminescence (PL) properties of PF6OC8 films prepared by IJP and spin coating is comparatively investigated. For both ink‐jet printed and spin coated films, the intensity of PL spectra first increases and then decreases with increase in the film thickness, probably due to the exciton quenching in thicker films. When the polymer film thickness is at nanoscale, the major peak in the PL spectrum is the 0–0 vibronic emission at about 420 nm, and with increase in the film thickness, the 0–1 vibronic peak at about 440 nm becomes dominant. The red‐shifted PL spectra with increase in film thickness show the change from the 2D exciton state to the 3D one. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis,characterization, and electroluminescence of new conjugated PPV derivatives bearing triphenylamine side‐chain through a vinylene bridge

Three new conjugated poly(p‐phenylene vinylene) (PPV) derivatives bearing triphenylamine side‐chain through a vinylene bridge, poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylene‐vinylene) (DP‐PPV), poly(2‐(3′‐(3″,7″‐dimethyloctyloxy)phenyl)‐1,4‐phenylenevinylene‐alt‐2‐(4′‐ (diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene) (DODP‐PPV), and poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene‐co‐2‐(3′,5′‐bis(3″,7″‐dimethyloctyloxy)‐1,4‐phenylenevinylene) (DP‐co‐BD‐PPV), were synthesized according to the Gilch or Wittig method. Among the three polymers, the copolymer DP‐co‐BD‐PPV is soluble in common solvents with good thermal stability with 5% weight loss at temperatures higher than 386°C. The weight‐average molecular weight (M_w) and polydispersity index (PDI) of DP‐co‐BD‐PPV were 1.83 × 10⁵ and 2.33, respectively. The single‐layer polymer light‐emitting diodes (PLEDs) with the configuration of Indium tin oxide (ITO)/poly (3,4‐ethylenedioxythiophene): poly(4‐styrene sulfonate)(PEDOT:PSS)/DP‐co‐BD‐PPV/Ca/Al were fabricated. The PLED emitted yellow‐green light with the turn‐on voltage of ca. 4.9 V, the maximum luminance of ca. 990 cd/m² at 15.8 V, and the maximum electroluminescence (EL) efficiency of 0.22 cd/A. Copyright © 2007 John Wiley & Sons, Ltd.     

Novel mesogen‐jacketed poly(p‐phenylenevinylene) derivatives bearing oxadiazole pendants: Design,synthesis, and optoelectronic properties

1,3,4‐oxadiazole moieties were laterally linked to the phenyl rings via a short ? OCH₂ spacer and a series of novel poly(p‐phenylenevinylene) derivatives have been successfully synthesized through Horner–Witting–Emmons coupling reaction. The structures and properties of the monomers and the resulting conjugated polymers were characterized by nuclear magnetic resonance spectroscope, Fourier transform infrared, elemental analysis, gel permeation chromatography, thermogravimetric analysis, UV–vis absorption (UV) spectroscopy, photoluminescence spectroscopy and cyclic voltammetry. The UV spectra at solution state was similar to what's observed at film state while the PL spectra at film state had a red shift from 19 to 28 nm compared with the results at solution state, which implied that the unique bulky jacketed structure containing oxadiazole unit of these copolymers could effectively suppress π‐stacking/aggregation. LUMO levels of these polymers varied from ?3.44 to ?3.63 eV with increasing content of oxadiazole units, which facilitated electron injection. PLEDs with the configuration of ITO/PEDOT/Polymer/TPBI (15 nm)/LiF (1 nm)/Al (100 nm) were fabricated, which emit a yellowish green light around 540 and 570 nm with a maximum brightness of 1074.7 cd/m² and luminous efficiency of 0.108 cd/A. The introduction of the unique bulky OXD unit into PPVs at a low molar content largely improved the electroluminescence properties of PPV. © Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7173–7186, 2008