Photoelectrochemical H2 Evolution with a Hydrogenase Immobilized on a TiO2‐Protected Silicon Electrode

The combination of enzymes with semiconductors enables the photoelectrochemical characterization of electron‐transfer processes at highly active and well‐defined catalytic sites on a light‐harvesting electrode surface. Herein, we report the integration of a hydrogenase on a TiO₂‐coated p‐Si photocathode for the photo‐reduction of protons to H₂. The immobilized hydrogenase exhibits activity on Si attributable to a bifunctional TiO₂ layer, which protects the Si electrode from oxidation and acts as a biocompatible support layer for the productive adsorption of the enzyme. The p‐Si|TiO₂|hydrogenase photocathode displays visible‐light driven production of H₂ at an energy‐storing, positive electrochemical potential and an essentially quantitative faradaic efficiency. We have thus established a widely applicable platform to wire redox enzymes in an active configuration on a p‐type semiconductor photocathode through the engineering of the enzyme–materials interface.     

Self‐powered Photoelectrochemical Sensor for Gallic Acid Exploiting a CdSe/ZnS Core‐shell Quantum Dot Sensitized TiO2 as Photoanode

Herein is described the development of a self‐powered sensor for gallic acid (GA) determination exploiting CdSe/ZnS quantum dot sensitized TiO₂ nanoparticles (CdSe/ZnS/TiO₂/FTO) as photoanode and an all copper oxide photocathode (CuO/Cu₂O/FTO) to reduce water. A two‐chamber self‐powered photoelectrochemical cell was employed in order to maintain separated the photoelectrodes. The self‐powered photoelectrochemical cell is based on water reduction in the cathodic chamber while gallic acid acts as a hole scavenger in the anodic chamber to generate the necessary cell output to drive GA oxidation in the anodic compartment. Electrochemical impedance measurements were performed to evaluate the electronic characteristics of CdSe/ZnS/TiO₂/FTO photoanode and CuO/Cu₂O/FTO photocathode in terms of flat band potential, carrier density, and nature of semiconductor. Under optimized conditions, the self‐powered photoelectrochemical cell presented a wide linear response range for GA from 1 μmol L⁻¹ up to 200 μmol L⁻¹.     

Size‐Dependence of the Activity of Gold Nanoparticle‐Loaded Titanium(IV) Oxide Plasmonic Photocatalyst for Water Oxidation

Mesoporous TiO₂ nanocrystalline film was formed on fluorine‐doped tin oxide electrode (TiO₂/FTO) and gold nanoparticles (NPs) of different sizes were loaded onto the surface with the loading amount kept constant (Au/TiO₂/FTO). Visible‐light irradiation (λ>430 nm) of the Au/TiO₂/FTO photoanode in a photoelectrochemical cell with the structure of photoanode|0.1 m NaClO4 aqueous solution|Ag/AgCl (reference electrode)|glassy carbon (cathode) leads to the oxidation of water to oxygen (O₂). We show that the visible‐light activity of the Au/TiO₂/FTO anode increases with a decrease in Au particle size (d) at 2.9≤d≤11.9 nm due to the enhancement of the charge separation and increasing photoelectrocatalytic activity.     

A Si Photocathode Protected and Activated with a Ti and Ni Composite Film for Solar Hydrogen Production

An efficient, stable and scalable hybrid photoelectrode for visible‐light‐driven H₂ generation in an aqueous pH 9.2 electrolyte solution is reported. The photocathode consists of a p‐type Si substrate layered with a Ti and Ni‐containing composite film, which acts as both a protection and electrocatalyst layer on the Si substrate. The film is prepared by the simple drop casting of the molecular single‐source precursor, [{Ti₂(OEt)₉(NiCl)}₂] (TiNi_pre), onto the p‐Si surface at room temperature, followed by cathodic in situ activation to form the catalytically active TiNi film (TiNi_cat). The p‐Si|TiNi_cat photocathode exhibits prolonged hydrogen generation with a stable photocurrent of approximately ?5 mA cm^?2 at 0 V vs. RHE in an aqueous pH 9.2 borate solution for several hours, and serves as a benchmark non‐noble photocathode for solar H₂ evolution that operates efficiently under neutral–alkaline conditions.     

Enhanced Photoelectrochemical Water Oxidation from CdTe Photoanodes Annealed with CdCl2

Most CdTe photoanodes and photocathodes show positive and negative photocurrent onset potentials for water oxidation and reduction, respectively, and are thus unable to drive photoelectrochemical (PEC) water splitting without external applied biases. Herein, the activity of a CdTe photoanode having an internal p‐n junction during PEC water oxidation was enhanced by applying a CdCl₂ annealing treatment together with surface modifications. The resulting CdTe photoanode generated photocurrents of 1.8 and 5.4 mA cm^?2 at 0.6 and 1.2 V_RHE, respectively, with a photoanodic current onset potential of 0.22 V_RHE under simulated sunlight (AM 1.5G). The CdCl₂ annealing increased the grain sizes and lowered the density of grain boundaries, allowing more efficient charge separation. Consequently, a two‐electrode tandem PEC cell comprising a CdTe‐based photoanode and photocathode split water without any external bias at a solar‐to‐hydrogen conversion efficiency of 0.51 % at the beginning of the reaction.     

Spatially Separated Photosystem II and a Silicon Photoelectrochemical Cell for Overall Water Splitting: A Natural–Artificial Photosynthetic Hybrid

Integrating natural and artificial photosynthetic platforms is an important approach to developing solar‐driven hybrid systems with exceptional function over the individual components. A natural–artificial photosynthetic hybrid platform is formed by wiring photosystem II (PSII) and a platinum‐decorated silicon photoelectrochemical (PEC) cell in a tandem manner based on a photocatalytic‐PEC Z‐scheme design. Although the individual components cannot achieve overall water splitting, the hybrid platform demonstrated the capability of unassisted solar‐driven overall water splitting. Moreover, H₂ and O₂ evolution can be separated in this system, which is ascribed to the functionality afforded by the unconventional Z‐scheme design. Furthermore, the tandem configuration and the spatial separation between PSII and artificial components provide more opportunities to develop efficient natural–artificial hybrid photosynthesis systems.     

g-C_3N_4基多功能层光阳极在光电化学水分解中的应用（英文）

光电化学分解水制氢可以一并解决环境问题和能源危机,因而成为研究热点.由于TiO_2 禁带宽度较大,不能有效吸收太阳光中的可见光,使光电化学分解水制氢的应用受限.g-C_3N_4的禁带宽度约为2.7 e V,能有效吸收可见光,但g-C_3N_4薄膜制备研究较少.我们通过热聚缩合法直接在FTO导电玻璃上制备出g-C_3N_4薄膜,发现其光电化学分解水制氢稳定性不高,选择易制备的TiO_2 作为保护层可以提高g-C_3N_4的耐用性.此外,为提高g-C_3N_4光生电子空穴对的分离能力,依靠Co-Pi对光生空穴的捕获作用而将其覆盖在最外层.因此本文首次制备一种新型的g-C_3N_4/TiO_2 /Co-Pi光阳极用于光电化学分解水制氢,其中g-C_3N_4用作光吸收层,TiO_2 用作保护层,Co-Pi用作空穴捕获层.并在此基础上,通过扫描电子显微镜(SEM),X射线衍射(XRD),紫外可见光谱(UV-Vis)等手段研究了g-C_3N_4/TiO_2 /Co-Pi光阳极的形貌特征和光电化学性能.SEM、EDS和XRD结果表明,g-C_3N_4/TiO_2 /Co-Pi光阳极被成功制备在了FTO导电玻璃上,厚度约为3μm.UV-Vis测试表明,g-C_3N_4的光吸收边约为470 nm,可以有效地吸收可见光,并且g-C_3N_4的框架结构使光多次反射折射增加了光的捕获能力,由此可见,g-C_3N_4能够发挥很好的光吸收层作用.通过对g-C_3N_4光阳极,g-C_3N_4/TiO_2 光阳极和g-C_3N_4/TiO_2 /Co-Pi光阳极的电流电压测试发现,g-C_3N_4/TiO_2 光阳极的光电流密度小于g-C_3N_4光阳极,而g-C_3N_4/TiO_2 /Co-Pi光阳极的光电流密在可逆氢电极1.1 V下达到了0.346 mA?cm–2,约为单独g-C_3N_4光阳极的3.6倍.这说明Co-Pi是提升g-C_3N_4光电化学性能的主要因素.电化学阻抗测试结果发现,g-C_3N_4/TiO_2 /Co-Pi光阳极的界面电荷转移电阻小于g-C_3N_4光阳极的,这表明g-C_3N_4/TiO_2 /Co-Pi光阳极界面处载流子转移较快,同时也能促进内部光生电子空穴对的分离,整体性能的提高应该主要归因于Co-Pi对光生空穴的捕获作用.恒电压时间测试展示出g-C_3N_4/TiO_2 /Co-Pi光阳极的光电流密度在2 h测试过程中没有明显下降,表明g-C_3N_4/TiO_2 /Co-Pi光阳极是相当稳定的,具有良好的耐用性,归因于TiO_2 和Co-Pi的共同保护作用,主要归因于TiO_2 层对FTO导电玻璃上的g-C_3N_4薄膜保护,从电化学沉积Co-Pi到所有测试结束.总体而言,g-C_3N_4/TiO_2 /Co-Pi光阳极加强的光电化学性能归因于以下几个因素:(1)g-C_3N_4优异的光吸收能力;(2)TiO_2 稳定的保护提升了g-C_3N_4薄膜的耐用性;(3)Co–Pi对光生空穴的捕获有效促进了光生电子空穴对的分离.     

Photoanodic and photocathodic behaviour of La5Ti2CuS5O7 electrodes in the water splitting reaction

The particulate semiconductor La₅Ti₂CuS₅O₇ (LTC) with a band gap energy of 1.9 eV functioned as either a photocathode or a photoanode when embedded onto Au or Ti metal layers, respectively. By applying an LTC/Au photocathode and LTC/Ti photoanode to, respectively, photoelectrochemical (PEC) water reduction and oxidation concurrently, zero-bias overall water splitting was accomplished under visible light irradiation. The band structures of LTC/Au and LTC/Ti calculated using a semiconductor device simulator (AFORS-HET) confirmed the critical role of the solid/solid junction of the metal back contact in the charge separation and PEC properties of LTC photoelectrodes. The prominently long lifetime of photoexcited charge carriers in LTC, confirmed by transient absorption spectroscopy, allowed the utilization of both photoexcited electrons and holes depending on the band structure at the solid/solid junction.     

Electrocatalytic and Solar‐Driven CO2 Reduction to CO with a Molecular Manganese Catalyst Immobilized on Mesoporous TiO2

Electrocatalytic CO₂ reduction to CO was achieved with a novel Mn complex, fac‐[MnBr(4,4′‐bis(phosphonic acid)‐2,2′‐bipyridine)(CO)₃] ( MnP ), immobilized on a mesoporous TiO₂ electrode. A benchmark turnover number of 112±17 was attained with these TiO₂| MnP electrodes after 2 h electrolysis. Post‐catalysis IR spectroscopy demonstrated that the molecular structure of the MnP catalyst was retained. UV/vis spectroscopy confirmed that an active Mn–Mn dimer was formed during catalysis on the TiO₂ electrode, showing the dynamic formation of a catalytically active dimer on an electrode surface. Finally, we combined the light‐protected TiO₂| MnP cathode with a CdS‐sensitized photoanode to enable solar‐light‐driven CO₂ reduction with the light‐sensitive MnP catalyst.     

Gold(Core)–Lead(Shell) Nanoparticle‐Loaded Titanium(IV) Oxide Prepared by Underpotential Photodeposition: Plasmonic Water Oxidation

Underpotential photodeposition of Pb yields an ultrathin shell layer on the Au(111) surface of Au nanoparticle(NP)‐loaded TiO₂ (Au/TiO₂) with heteroepitaxial nanojunctions. The localized surface plasmon resonance of Au/TiO₂ undergoes no damping with the Pb‐shell formation, and the Pb shell offers resistance to aerobic oxidation. Mesoporous films comprising the Au(core)–Pb(shell) NP‐loaded TiO₂ and unmodified Au/TiO₂ were formed on fluorine‐doped tin oxide (FTO) electrode. Using them as the photoanode, photoelectrochemical cells were fabricated, and the photocurrent was measured under illumination of simulated sunlight. The photocurrent for water splitting is dramatically enhanced by the Pb‐shell formation. The photoelectrochemical measurements of the hot‐electron lifetime and density functional theory calculations for model clusters indicate that the Pb‐shell effect originates from the charge separation enhancement.     

Heterostructure of Si and CoSe2: A Promising Photocathode Based on a Non‐noble Metal Catalyst for Photoelectrochemical Hydrogen Evolution

Development of a solar water splitting device requires design of a low‐cost, efficient, and non‐noble metal compound as alternative to noble metals. For the first time, we showed that CoSe₂ can function as co‐catalyst in phototoelectrochemical hydrogen production. We designed a heterostructure of p‐Si and marcasite‐type CoSe₂ for solar‐driven hydrogen production. CoSe₂ successively coupled with p‐Si can act as a superior photocathode in the solar‐driven water splitting reaction. Photocurrents up to 9 mA cm^?2 were achieved at 0 V vs. reversible hydrogen electrode. Electrochemical impedance spectroscopy showed that the high photocurrents can be attributed to low charge transfer resistance between the Si and CoSe₂ interfaces and that between the CoSe₂ and electrolyte interfaces. Our results suggest that this CoSe₂ is a promising alternative co‐catalyst for hydrogen evolution.     

Enriched Surface Oxygen Vacancies of Photoanodes by Photoetching with Enhanced Charge Separation

A facile photoetching approach is described that alleviates the negative effects from bulk defects by confining the oxygen vacancy (O_vac) at the surface of BiVO₄ photoanode, by 10‐minute photoetching. This strategy could induce enriched O_vac at the surface of BiVO₄, which avoids the formation of excessive bulk defects. A mechanism is proposed to explain the enhanced charge separation at the BiVO₄ /electrolyte interface, which is supported by density functional theory (DFT) calculations. The optimized BiVO₄ with enriched surface O_vac presents the highest photocurrent among undoped BiVO₄ photoanodes. Upon loading FeOOH/NiOOH cocatalysts, photoetched BiVO₄ photoanode reaches a considerable water oxidation photocurrent of 3.0 mA cm^?2 at 0.6 V vs. reversible hydrogen electrode. An unbiased solar‐to‐hydrogen conversion efficiency of 3.5 % is realized by this BiVO₄ photoanode and a Si photocathode under 1 sun illumination.     

The effect of ionic and electronic properties of titanium oxide on the electrochemical growth and redox behavior of polyaniline on titanium surfaces

Polyaniline (PANI) was electrodeposited directly from aniline (ANI)-containing sulfuric acid media on Ti|TiO₂ electrodes, which were prepared in ANI-free 0.5 M H₂SO₄ solution by applying suitable anodization conditions in order to control the donor density (N _D) in the oxide layer of a fixed thickness. By using the suggested procedure, reproducible conditions for the cyclic voltammetric growth of PANI on Ti can be achieved, and most importantly, the properties of Ti|TiO₂|PANI electrodes can be modulated to meet the requirements for specific applications. The polymerization rate and the deposited amount of PANI were found to depend strongly on the N _D estimated by Mott-Schottky analysis. The redox behavior of the resulted Ti|TiO₂|PANI electrodes indicated differences in acid solutions as compared with the corresponding behavior of other PANI-modified metal surfaces. Analysis of the anodic and cathodic electrochemical response of the prepared Ti|TiO₂|PANI electrodes discloses the significant role of ionic and electronic properties of the intervening oxide between the metal support and PANI.     

Porous Si/TiO2 nanowire photoanode for photoelectric catalysis under simulated solar light irradiation

Porous Si/TiO₂ nanowire photoanodes were prepared by a combination of hydrothermal synthesis and metal‐assisted chemical etching. Characterization of samples was conducted using scanning electron microscopy and X‐ray diffraction, the results showing that a porous Si/TiO₂ heterojunction structure was synthesized. Diffuse reflection spectra show that the porous Si/TiO₂ nanowire photoanodes have a strong absorption. Photocurrent measurement shows that the photocurrent of the porous Si/TiO₂ nanowire photoanodes at 6 h is higher than that of others in the measuring region. The photoelectric catalysis (PEC) activities of porous Si/TiO₂ nanowire photoanodes were evaluated in degradation experiments of methylene blue under simulated solar light irradiation, and the sample at 6 h shows the highest PEC activity. Meanwhile, the PEC activity of the porous Si/TiO₂ nanowire photoanode is higher than that of the single direct photocatalysis process or electric catalysis. The mechanism of the PEC of the porous Si/TiO₂ nanowire photoanodes has been explained.     

Water oxidation on N‐Doped TiO2 nanotube arrays

Photocatalytic splitting water into hydrogen and oxygen by utilizing solar energy is regarded as an effective strategy to solve oil crisis. By utilizing density functional calculations, we herein present the systemic studies with respect to water splitting mechanism on N‐doped TiO₂ nanotube arrays (NTAs), and focus on activation energy, thermodynamic properties, and effects of N‐doping on reaction process. Our results reveal that the impurity 2p states of doped nitrogen effectively change electronic structure of TiO₂ NTAs, which act as an electron acceptor and facilitate weakly bound electrons of valence band to be easily excited to acceptor level, as well as enhance the first H₂O adsorption and dissociation on the inside wall of N‐doped TiO₂ NTAs. Therefore, it is found that the rate‐determining step of water splitting is the formation reaction of HOO* on N‐doped TiO₂ NTAs rather than the formation of HO* from the first H₂O. © 2011 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Structural Control of Hierarchically‐Ordered TiO2 Films by Water for Dye‐Sensitized Solar Cells

A facile way of controlling the structure of TiO₂ by changing the amount of water to improve the efficiency of dye‐sensitized solar cells (DSSCs) is reported. Hierarchically ordered TiO₂ films with high porosity and good interconnectivity are synthesized in a well‐defined morphological confinement arising from a one‐step self‐assembly of preformed TiO₂ (pre‐TiO₂) nanocrystals and a graft copolymer, namely poly(vinyl chloride)‐g‐poly(oxyethylene methacrylate). The polymer–solvent interactions in solution, which are tuned by the amount of water, are shown to be a decisive factor in determining TiO₂ morphology and device performance. Systematic control of wall and pore size is achieved and enables the bifunctionality of excellent light scattering properties and easy electron transport through the film. These properties are characterized by reflectance spectroscopy, incident photon‐to‐electron conversion efficiency, and electrochemical impedance spectroscopy analyses. The TiO₂ photoanode that is prepared with a higher water ratio, [pre‐TiO₂]:[H₂O]=1:0.3, shows a larger surface area, greater light scattering, and better electron transport, which result in a high efficiency (7.7 %) DSSC with a solid polymerized ionic liquid. This efficiency is much greater than that of commercially available TiO₂ paste (4.0 %).     

BiVO4/TiO2 core-shell heterostructure: wide range optical absorption and enhanced photoelectrochemical and photocatalytic performance

In the present study, pristine BiVO₄, TiO₂ and BiVO₄/TiO₂ core-shell heterostructured nanoparticles are prepared by hydrothermal methods and studied for structural, morphological, optical, photoelectrochemical water splitting and photocatalytic degradation of methylene blue as an organic pollutant. Both pristine BiVO₄ and TiO₂ exhibit poor PEC and PC performance under visible light illumination. However, an enhanced PEC and PC activity in BiVO₄/TiO₂ core-shell heterostructure is observed due to high solar energy absorption and superior charge separation properties in core-shell nanoparticles. The photoelectrode prepared using BiVO₄/TiO₂ core-shell nanoparticles exhibit a photocathode behavior and produced cathodic photocurrent, however, the pristine BiVO₄ and TiO₂ photoelectrodes act as photoanode and produced anodic photocurrent. This behavior of change in current direction is also observe in the Mott-Schottky analysis where the BiVO₄/TiO₂ core-shell nanoparticles photoelectrode exhibits the positive slow showing p-type semiconducting behavior. The change in cathodic photoresponse in core-shell nanoparticles in comparison to anodic photoresponse of BiVO₄ and TiO₂ nanoparticles is explained in terms of the variations in the work function values. These results highlight the advantages of core-shell nanoparticle of suitable materials for photocatalytic and photoelectrochemical applications.     

Solar‐Assisted eBiorefinery: Photoelectrochemical Pairing of Oxyfunctionalization and Hydrogenation Reactions

Inspired by natural photosynthesis, biocatalytic photoelectrochemical (PEC) platforms are gaining prominence for the conversion of solar energy into useful chemicals by combining redox biocatalysis and photoelectrocatalysis. Herein, we report a dual biocatalytic PEC platform consisting of a molybdenum (Mo)‐doped BiVO₄ (Mo:BiVO₄) photoanode and an inverse opal ITO (IO‐ITO) cathode that gives rise to the coupling of peroxygenase and ene‐reductase‐mediated catalysis, respectively. In the PEC cell, the photoexcited electrons generated from the Mo:BiVO₄ are transferred to the IO‐ITO and regenerate reduced flavin mononucleotides to drive ene‐reductase‐catalyzed trans‐hydrogenation of ketoisophrone to (R)‐levodione. Meanwhile, the photoactivated Mo:BiVO₄ evolves H₂O₂ in situ via a two‐electron water‐oxidation process with the aid of an applied bias, which simultaneously supplies peroxygenases to drive selective hydroxylation of ethylbenzene into enantiopure (R)‐1‐phenyl‐1‐hydroxyethane. Thus, the deliberate integration of PEC systems with redox biocatalytic reactions can simultaneously produce valuable chemicals on both electrodes using solar‐powered electrons and water.     

Synergistic Cocatalytic Effect of Carbon Nanodots and Co3O4 Nanoclusters for the Photoelectrochemical Water Oxidation on Hematite

Cocatalysis plays an important role in enhancing the activity of semiconductor photocatalysts for solar water splitting. Compared to a single cocatalyst configuration, a cocatalytic system consisting of multiple components with different functions may realize outstanding enhancement through their interactions, yet limited research has been reported. Herein we describe the synergistic cocatalytic effect between carbon nanodots (CDots) and Co₃O₄, which promotes the photoelectrochemical water oxidation activity of the Fe₂O₃ photoanode with a 60 mV cathodically shifted onset potential. The C/Co₃O₄‐Fe₂O₃ photoanode exhibits a photocurrent density of 1.48 mA cm^?2 at 1.23 V (vs. reversible hydrogen electrode), 78 % higher than that of the bare Fe₂O₃ photoanode. The slow reaction process on the single Co^III‐OH site of the Co₃O₄ cocatalyst, oxidizing H₂O to H₂O₂ with two photogenerated holes, could be accelerated by the timely H₂O₂ oxidation to O₂ catalyzed on CDots.     

Utilization of natural pigment extracted from pomegranate fruits as sensitizer in solid-state solar cells

The juice extracted from pomegranate fruits containing cyanin (flavylium) is utilized as the light-harvesting analog in a dye sensitized solid-state photovoltaic cell. Strong chelation of flavylium with TiO₂ changes it to quinonoidal form. A higher incident photon to current conversion efficiency is observed in solid-state TiO₂|pomegranate piment|CuI solar cell compare to that of the cells (TiO₂|dye|CuI type) sensitized with other natural pigments.