Highly Selective Chromium(III) PVC‐Membrane Electrodes Based on Some Recently Synthesized Schiff's Bases

Three recently synthesized Schiff's bases were studied to characterize their ability as Cr³⁺ ion carrier in PVC‐membrane electrodes. The polymeric membrane (PME) and coated glassy carbon (CGCE) electrodes based on 2‐hydroxybenzaldehyde‐O,O′‐(1,2‐dioxetane‐1,2‐diyl) oxime (L1) exhibited Nernstian responses for Cr³⁺ ion over wide concentration ranges (1.5×10^?6–8.0×10^?3 M for PME and 4.0×10^?7–3.0×10^?3 M for CGCE) and very low limits of detection (1.0×10^?6 M for PME and 2.0×10^?7 M for CGCE). The proposed potentiometric sensors manifest advantages of relatively fast response and, most importantly, good selectivities relative to a wide variety of other cations. The selectivity behavior of the proposed Cr³⁺ ion‐selective electrodes revealed a considerable improvement compared to the best previously PVC‐membrane electrodes for chromium(III) ion. The potentiometric responses of the electrodes are independent of pH of the test solution in the pH range 3.0–6.0. The electrodes were successfully applied to determine chromium(III) in water samples.     

New Macrocyclic Diamides as Neutral Ionophores for Highly Selective and Sensitive PVC‐Membrane Electrodes for Be2+ Ion

Five recently synthesized macrocyclic diamides were investigated to characterize their ability as beryllium ion carriers in potentiometric PVC‐membrane electrodes. The electrodes based on 1,15‐diaza‐3,4;12,13‐dibenzo‐5,8,11‐trioxabicyclo[13,2,2] heptadecane‐2,14‐dione exhibited a Nernstian response for Be²⁺ ion over wide concentration ranges (from 3.0×10^?6 to 3.0×10^?2 M for polymeric membrane electrode, PME, and from 5.0×10^?7 to 2.0×10^?2 M for coated glassy carbon electrode, CGCE) and very low detection limits (2.0 ×10^?6 M for PME and 4.0×10^?7 M for (CGCE). The electrodes possess low resistances, fast responses, satisfactory reproducibilities and, most importantly, good selectivities relative to a variety of other common cations. The potentiometric response of the electrodes is independent of pH of test solution in the pH range of 4.0–7.5. The proposed sensors were used to determine beryllium ion in water samples.     

Synthesis,metal ion complexation and first use of a thia-aza substituted macrocyclic diamide as a novel sensing material for preparation of selective and sensitive poly(vinyl chloride)-membrane potentiometric sensors for Ag+ ion

A novel thia-aza substituted macrocyclic diamide 7,10,13-triaza-1-thia-4,16-dioxa-20,24-dimethyl-2,3;17,18-dibenzo-cyclooctadecane-6,14-dione (L) was synthesized and stability of its complexes with several alkaline earth, transition and heavy metal ions were studied conductometrically in methanol solution. The resulting 1:1 Ag⁺–L complex found to be the most stable one among all cation complexes studied. The optimized structures of the ligand and its Ag⁺ complex were also investigated. Based on the preliminary results thus obtained, L was used as an excellent sensing material to prepare polymeric membrane (PME) and coated graphite (CGE) silver-selective electrodes. The electrodes revealed a Nernstian behavior over wide Ag⁺ ion concentration ranges (i.e., 2.0 × 10^?6–1.0 × 10^?2 M for PME and 5.0 × 10^?7–1.0 × 10^?2 M for CGE). The potentiometric responses were independent of pH of the test solution in the range 2.9–6.8. The electrodes possessed advantages of low resistance, relatively fast response time, long lifetimes and, especially, good selectivity relative to a wide variety of other cations. The electrodes were used, as indicator electrodes, in the potentiometric titration of silver ion and in the determination of Ag⁺ ion in waste water, photographic emulsion, radiographic and photographic films and dental amalgams.     

Highly Selective and Sensitive Membrane Sensors for Copper(II) Ion Based on a New Benzo‐Substituted Macrocyclic Diamide 6,7,8,9,10‐Hexahydro‐2H‐1,13,4,7,10‐benzodioxatriazacyclopentadecine‐3,11(4H,12H)‐dione

Novel PVC membrane (PME) and coated graphite (CGE) Cu²⁺‐selective electrodes based on 5,6,7,8,9,10‐hexahydro‐2H‐1,13,4,7,10‐benzodioxatriazacyclopentadecine‐3,11(4H,12H)‐dione are prepared. The electrodes reveal a Nernstian behavior over wide Cu²⁺ ion concentration ranges (1.0×10^?7–1.0×10^?1 M for PME and 1.0×10^?8–1.0×10^?1 M for CGE) with very low limits of detection (7.8×10^?8 M for PME and 9.1×10^?9 M for CGE). The potentiometric responses are independent of the pH of the test solutions in the pH range 2.7–6.2. The proposed electrodes possess very good selectivities for Cu²⁺ over a wide variety of the cations including alkali, alkaline earth, transitions and heavy metal ions. The practical utility of the proposed electrodes have been demonstrated by their use in the study of interactions between copper ions and human growth hormone (hGH) in biological systems, potentiometric titration of copper with EDTA and determination of copper content of a sheep blood serum sample and some other real samples.     

[Cu(L)](NO3)2 (L=4,7‐Bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) as a Suitable Ionophore for Construction of Thiocyanate‐Selective Electrodes and Their Use in Determination of Urinary and Salivary Thiocyanate Concentration

The construction, performance characteristics, and application of polymeric membrane (PME) and coated graphite (CGE) thiocyanate‐selective electrodes are reported. The electrodes were prepared by incorporating the complex [Cu(L)](NO₃)₂ (L=4,7‐bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) into a plasiticized poly(vinyl chloride) membrane. The influence of membrane composition, pH of test solution, and foreign ions were investigated. The electrodes reveal Nernstian behavior over a wide SCN^? ion concentration range (1.0×10^?6–1.0×10^?1 M for PME and 5.0×10^?7–1.0×10^?2 M for CGE) and show fast dynamic response times of 15 s and lower. The proposed sensors show high selectivity towards thiocyanate over several common organic and inorganic anions. They were successfully applied to the direct determination of thiocyanate in urine and saliva of smokers and nonsmokers, and as an indicator electrode in titration of Ag⁺ ions with thiocyanate.     

Silver(I)-selective membrane potentiometric sensor based on two recently synthesized ionophores containing calix[4]arene

Two new PVC membrane electrodes that are highly selective to Ag(I) ions were prepared using (L₁) calyx[4]arene (L₂) as two suitable neutral carriers. The silver(I) ion selective electrodes exhibit a good response for silver ion over a wide concentration range of 1.0 × 10⁻¹ to 4.2 × 10⁻⁶ M (L₁) and 1.0 × 10⁻¹ to 6.5 × 10⁻⁶ M (L₂) with a Nernstian slope of 60 mV per decade (L₁) and 58 mV per decade (L₂) at 25°C, and was found to be very selective, precise, and usable within the pH range 4.0–8.0. They have a response time of <15 s and can be used for at least 3 months without any measurable divergence in potential. The proposed sensors show a fairly good discriminating ability towards Ag⁺ ion in comparison to some hard and soft metal ions. The electrodes were used as indicator electrodes in the potentiometric titration of silver ion and in the determination of Ag⁺ in photographic emulsion and radiographic and photographic films. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 862–868. The article is published in the original.     

Novel Ytterbium(III) Selective Membrane Sensor Based on N‐(2‐Pyridyl)‐N′‐(2‐Methoxyphenyl)‐Thiourea as an Excellent Carrier and Its Application to Determination of Fluoride in Mouth Wash Preparation Samples

The construction, performance, and applications of a novel ytterbium(III) sensor based on N‐(2‐pyridyl)‐N′‐(2‐methoxyphenyl)‐thiourea (PMT), as an excellent carrier, in plasticized poly(vinyl chloride) PVC matrix, is described. The influences of membrane composition and pH on the potentiometric response of the sensor were investigated. The sensor exhibits a nice Nernstian response for Yb(III) ion over a wide concentration range of 4 decades of concentration (1.0×10^?6–1.0×10^?2 M), and a detection limit of 5.0×10^?7 M. The response time of the electrodes is between 8 and 10 s, depending on the concentration of ytterbium(III) ions. The proposed sensor can be used for about 8 weeks without any considerable divergence in potential. The sensor revealed very good selectivity for Yb(III) in the presence of several metal ions. The best performance was observed for the membrane containing; 30% PVC, 59% o‐nitrophenyloctyl ether (NPOE) as solvent mediator, 7% PMT, and 4% sodium tetraphenyl borate (NaTPB). It was successfully applied as indicator electrodes in the potentiometric titration of Yb(III) with EDTA and for the determination of fluoride ion in two mouth wash formulations. The proposed La(III) sensor was found to work well under laboratory conditions. It was also used as an indicator electrode in titration of a 1.0×10^?4 M of Yb(III) with a standard EDTA solution (1.0×10^?2 M). It was also used for determination of Yb(III) ion in Xenotime .     

Novel Ag ion-selective electrodes based on two new mixed azathioether crowns containing a 1,10-phenanthroline sub-unit

Novel polymeric membrane (PME) and coated graphite (CGE) silver-selective electrodes based on two recently synthesized mixed azathioether crowns containing a 1,10-phenanthroline sub-unit were prepared. The electrodes reveal a Nernstian behavior over quite wide Ag⁺ ion concentration ranges with a very low limits of detection (LOD) (i.e. down to 1.0×10⁻⁸ M for CGEs and 8.0×10⁻⁷ M for PMEs). The potentiometric responses are independent of the pH of the test solution in the pH range 3.0-7.0. The electrodes possess advantages of low resistance, very fast response time, relatively long lifetimes and, especially, good selectivities relative to a wide variety of other cations. The electrodes were used, as indicator electrodes, in the potentiometric titration of silver ion and in the determination of Ag⁺ in waste water, photographic emulsion and radiographic and photographic films.     

Iodide‐Selective Electrode Based on Copper Phthalocyanine

Copper phthalocyanine was used as ion carrier for preparing polymeric membrane selective sensor for detection of iodide. The electrode was prepared by incorporating the ionophore into plasticized poly(vinyl chloride) (PVC) membrane, coated on the surface of graphite electrode. This novel electrode shows high selectivity for iodide with respect to many common inorganic and organic anions. The effects of membrane composition, pH and the influence of lipophilic cationic and anionic additives and also nature of plasticizer on the response characteristics of the electrode were investigated. A calibration plot with near‐Nernestian slope for iodide was observed over a wide linear range of five decades of concentration (5×10^?6?1×10^?1 M). The electrode has a fast response time, and micro‐molar detection limit (ca. 1×10^?6 M iodide) and could be used over a wide pH range of 3.0–8.0. Application of the electrode to the potentiometric titration of iodide ion with silver nitrate is reported. This sensor is used for determination of the minute amounts of iodide in lake water samples.     

Membrane Composition Effects on the Analytical Behavior of Solid Contact Potentiometric Pb2+ Selective Electrodes Based on Diazadibenzo‐18‐crown‐6 Ionophores

The effect of component contents and membrane thickness on the detection limit (DL), slope (m), linear range (LR) and response time (RT) of Pb²⁺ solid contact potentiometric ion selective electrodes (SCISE) based on 4,10‐diaza‐2,3,11,12‐dibenzo‐18‐crown‐6 (1), 4,10‐diaza‐2,3,11,12‐di(4‐tert‐butylbenzo)‐18‐crown‐6 (2) and 4,10‐diaza‐2,3,11,12‐dibenzo‐18‐crown‐6‐N,N′‐di(carboxymethyl) (3) as ionophores was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) measurements. The use of an intermediate layer of poly(3‐octyl)thiophene between the gold substrate and the selective membrane was explored. SCISE prepared showing the best responses had typical DL, m, LR and RT values of 10^?6 M, 29 mV/dec, 10^?5 to 10^?3 M and 2 minutes.     

A Novel Al(III)‐Selective Electrochemical Sensor Based on N,N′‐Bis(salicylidene)‐1,2‐phenylenediamine Complexes

A polyvinylchloride membrane sensor based on N,N′‐bis(salecylidene)‐1,2‐phenylenediamine (salophen) as membrane carrier was prepared and investigated as a Al³⁺‐selective electrode. The sensor exhibits a Nernstian response toward Al(III) over a wide concentration range (8.0×10^?7–3.0×10^?2 M), with a detection limit of 6.0×10^?7 M. The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 3.2–4.5. The electrode possesses advantages of very fast response and high selectivity for Al³⁺ in comparison with alkali, alkaline earth and some heavy metal ions. The sensor was used as an indicator electrode, in the potentiometric titration of aluminum ion and in determination of Al³⁺ contents in drug, water and waste water samples.     

Novel Cesium‐Selective Electrodes Based on Lipophilic 1,3‐Bisbridged Cofacial‐calix[6]crowns

Five bisbridged calix[6]crowns have been investigated as Cs⁺ ionophore in PVC membrane electrodes. As ionophores, three 1,3‐bisbridged calix[6]crown‐4‐ethers( I–III ), 1,3‐bisbridged calix[6]crown‐5‐ether( IV ), and 1,3‐bisbridged calix[6]crown‐6‐ether( V ) have been evaluated. The membranes all give good Nernstian response in the concentration range from 1×10^?7 to 1×10^?1 M of cesium ion. The best detection limits (?log aequation/tex2gif-inf-1.gif=7.08–7.36) are obtained for electrode membranes containing 1,3‐bisbridged cofacial‐calix[6]crown‐4‐ethers( I‐III ), and the values are the lowest compared with those reported previously. The highest selectivity coefficients [ 3.74(Cs/K), 2.63(Cs/Rb)] are obtained for the membrane of 1,3‐bisbridged calix[6]crown‐4‐ether( II ), and these values are also the highest compared with previous reports for Cs⁺‐ISEs. The highest selectivity towards cesium ion is attributed to the geometrically cofacial positions of two crown‐ethers in calix[6]crowns in order to provide the complex of cesium ion and eight oxygens of cofacial crowns.     

Carbon Paste Electrode Modified with Functionalized Nanoporous Silica Gel as a New Sensor for Determination of Silver Ion

A new dipyridyl‐functionalized silica gel (DPSG) was synthesized. The potentiometric response of silver ion was investigated at a carbon paste electrode chemically modified with functionalized nanoporous silica gel. The electrodes with a DPSG proportions of 10.1% (w/w), showed very stable potential. Calibration plots with Nernstian slopes for Ag⁺ were observed, 58.7 (±0.9) mV decade^?1, over a wide linear range of concentration (5.0×10^?7 to 1.0×10^?1 M). The electrode has a detection limit of 1.0×10^?7 M. The selectivity coefficients measured by the match potential method in acetate buffer, pH 5.5, were investigated. The electrode has fast response time, high performance, high sensitivity in wide cation activity ranges, and good long term stability (more than 6 months). The method was satisfactory and used to determine the concentration of silver ion in waste waters contaminated by this metal.     

Highly Selective and Sensitive Triiodide PVC‐Membrane Electrode Based on a New Charge‐Transfer Complex of Bis(2,4‐Dimethoxybenzaldehyde)butane‐2,3‐Dihydrazone with Iodine

In this work, a highly selective membrane triiodide sensor based on a new charge‐transfer complex of bis(2,4‐dimethoxybenzaldehyde)butane‐2,3‐dihydrazone with iodine (Iodide Charge Transfer complex: ICT) as membrane carrier is introduced. The influences of five different solvent mediators on sensitivity and selectivity of the proposed sensor were considered. The best performance was obtained with the membrane composition containing 30% poly (vinyl chloride), 63% DBP, 5% ICT and 2% HTAB. The electrode shows a Nernstian behavior over a very wide triiodide ion concentration range (1.0 × 10^?7‐1.0 × 10^?2 M), and a detection limit value of 8.0 × 10^?8 M. The effect of pH on the potentiometric response of the sensor was also studied, and it was found that the response of the electrode is independent of the pH of the solution in the pH range of 4.0–10. The proposed sensor has a very fast response time (< 12 s), and good selectivities relative to a wide variety of common inorganic and organic anions, including iodide, acetate, bromide, chloride, fluoride, nitrite, nitrate, sulfite, sulfate, cyanide and thiocyanate. In fact the selectivity behavior of the proposed triiodide ion‐selective electrode shows great improvements compared to the previously reported electrodes for triiodide ion. The proposed membrane sensor can be used for at least 6 months without any divergence in the potentials. The electrode was successfully applied as an indicator electrode in the titration of triiodide with thiosulfate ion.     

Polymeric Membrane Lanthanum(III)‐Selective Electrode Based on N,N′‐Adipylbis(5‐phenylazo salicylaldehyde hydrazone)

A recently synthesized azao‐containing Schiff's base N,N′‐adipylbis(5‐phenylazo salicylaldehyde hydrazone) was used as a suitable neutral ion carrier in construction of a highly selective La³⁺‐PVC membrane electrode. The electrode exhibits a Nernstian response with a slope of 19.4 mV decade^?1 over a wide concentration range (1.0×10^?6–1.0×10^?2 M) and a limit of detection of 4.0×10^?7 M (0.05 ppm). The electrode possesses a fast response time of ca. 10 s and can be used for at least 3 months without observing any deviation. The proposed electrode revealed excellent selectivity for La³⁺ over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.0–8.0. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of La³⁺ ions with EDTA and in determination of F^? ion in some pharmaceutical preparations.     

Design of a Vitamin B1‐Selective Electrode Based on an Ion‐Pair and Its Application to Pharmaceutical Analysis

Vitamin B₁‐selective electrodes with PVC membrane were developed that contain ion associates of vitamin B₁ with an inorganic anion, BiI₄^?, and an organic anion, brilliant yellow, as electrode‐active substances. The linearity ranges of the electrode function are 1.0×10^?5–1.0×10^?2 and 1.0×10^?4–1.0×10^?2 M, the electrode function slopes are 33.0±1.0 and 33.1±1.1 mV decade^?1, the detection limits are 5.5×10^?6 and 8.3×10^?5 M for BiI₄^? and brilliant yellow respectively. The working range of pH is 5–12. The efficiency of the use of electrodes for the vitamin B₁ content control in multivitamin pharmaceutical preparations was shown by direct potentiometry and potentiometric titration methods.     

Chromium(III) Potentiometric Sensor Based on Para‐Tertiary‐Butyl Calix[4]arene

A new chromium(III) PVC membrane sensor incorporating p‐tertiary‐butyl calix[4]arene as ionophore, potassium tetrakis as additive and dibutyl phthalate (DBP) as plasticizer was constructed. The electrode exhibited an excellent potentiometric response over a wide concentration range of 1.0×10^?7–1.0×10^?1 M with a Nernstian slope of 20±0.5 mV per decade. The detection limit was 5.0×10^?8 M. The electrode showed a better performance over a pH range of 3.0–8.0, and had a short response time of about <15 s.The electrode was successfully applied to potentiometric titration of Cr (III) with EDTA and for direct determination of chromium(III) in waste water.     

Highly Selective and Sensitive Copper(II) Membrane Sensors Based on 6‐Methyl‐4‐(1‐phenylmethylidene)amino‐3‐thioxo‐1,2,4‐triazin‐5‐one as a New Neutral Ionophore

A new Cu(II) ion‐selective PVC membrane sensor based on 6‐methyl‐4‐(1‐phenylmethylidene)amino‐3‐thioxo‐1,2,4‐triazin‐5‐one (MATTO) as an excellent sensing material was developed. The electrode exhibits a Nernstian slope of 29.2±0.4 mV per decade over a very wide concentration range between 1.0×10^?1 and 1.0×10^?6 M, with a detection limit of 4.8×10^?7 M (30.5 ng/mL). The sensor possesses the advantages of short conditioning time, fast response time (<10 s), and especially, very good selectivity towards transition and heavy metal, and some mono, di and trivalent cations. The proposed electrode was successfully applied to the determination of copper in wastewater of copper electroplating samples and as an indicator electrode in potentiometric titration of Cu(II) ions with EDTA.     

Novel Potentiometric PVC‐Membrane and Coated Graphite Sensors for Lanthanum(III)

Preliminary theoretical studies revealed the selective complexation of bis (2‐mercaptoanil) diacetyl (BMDA) with La³⁺ over several alkali, alkaline earth and heavy metal ions. Thus, novel PVC‐based membrane (PBM) and coated graphite membrane (CGM) sensors for La(III) based on BMDA were prepared. The electrodes display Nernstian behavior over wide concentration ranges (i.e., 1.0×10^?5–1.0×10^?1 M for PBM and 1.0×10^?6–1.0×10^?1 M for CGM). The potential response of sensors was pH independent in the range of 4.0–8.0. The sensors possess satisfactory reproducibility, fast response time (<15 s), and specially excellent discriminating ability for La³⁺ ions with respect to most of the cations. The membrane sensor was used as an indicator electrode in potentiometric titration of lanthanum ions with EDTA. The coated graphite membrane electrode was applied in determination of fluoride ions in mouth wash preparations.     

A Novel PVC‐Membrane‐Coated Graphite Sensor Based on an Anthraquinone Derivative Membrane for the Determination of Lead

A highly selective membrane electrode for the determination of ultratrace amounts of lead was prepared. The PVC membrane electrode based on 2‐(2‐ethanoloxymethyl)‐1‐hydroxy‐9,10‐anthraquinone (AQ), directly coated on graphite, exhibits a good Nernstian response for Pb(II) ions over a very wide concentration range (1.0×10^?7–1.0×10^?2 M) with a limit of detection of 8.0×10^?8 M. It has a fast response time of ca. 10 s and can be used over a period 2 months with good reproducibility (SD=±0.2 mV). The electrode revealed a very good selectivity respect to common alkali, alkaline earth, transition and heavy metal ions and could be used in the pH range of 3.5–6.8. It was used as an indicator electrode in potentiometric titration of lead ions with chromate and oxalate, and in indirect determination of lead in spring water samples.