Facile synthesis of PtRu/C electrocatalyst with high activity and high loading for passive direct methanol fuel cell by synergetic effect of ultrasonic radiation and mechanical stirring

The PtRu/C electrocatalyst with high loading (PtRu of 60 wt%) was prepared by synergetic effect of ultrasonic radiation and mechanical stirring. Physicochemical characterizations show that the size of PtRu particles of as-prepared PtRu/C catalyst is only several nanometers (2–4 nm), and the PtRu nanoparticles were homogeneously dispersed on carbon surface. Electrochemistry and single passive direct methanol fuel cell (DMFC) tests indicate that the as-prepared PtRu/C electrocatalyst possessed larger electrochemical active surface (EAS) area and enhanced electrocatalytic activity for methanol oxidation reaction (MOR). The enhancement could be attributed to the synergetic effect of ultrasound radiation and mechanical stirring, which can avoid excess concentration of partial solution and provide a uniform environment for the nucleation and growth of metal particles simultaneously hindering the agglomeration of PtRu particles on carbon surface.     

Boron-doped diamond powder as catalyst support for fuel cell applications

The modification of boron-doped diamond powder with metallic oxides using the sol–gel method to prepare high area and very stable electrodes for the methanol oxidation reaction is reported here. The catalyst clusters thus prepared are irregularly distributed on the BDD powder surface having sizes varying between 500 nm and 5 μm and formed by the agglomeration of many nanoparticles. Electrochemical studies in acid media demonstrate that the deposited particles have a good electrical contact with the diamond powder surface and high purity. Moreover, the use of the sol–gel method on a BDD powder substrate leads to the formation of metallic and metallic oxides deposits of the desired composition. The electrocatalyst composite prepared in this manner (Pt–RuO_x/BDD powder) shows an excellent activity for methanol oxidation presenting an onset potential 20 mV lower than that observed on a Pt–Ru/C commercial catalyst, probably due to the ruthenium oxide contribution to the overall catalytic activity.     

Synthesis of highly active nanostructured PtRu electrocatalyst with three-dimensional mesoporous silica template

Nanostructured PtRu material has been successively synthesized via chemical co-reduction of hexachloroplatinic acid and ruthenium trichloride using three-dimensional (3D) hexagonal mesoporous SBA-12 silica as a solid template, and has been studied as an electrocatalyst toward methanol electro-oxidation. The ordered nanostructure of the PtRu particles has been disclosed by transmission electron micrographs and is characterized by regular pores of ca. 3.0 ± 0.3 nm in diameter separated by walls of ca. 3.0 ± 0.3 nm thick. X-ray diffraction and energy dispersive X-ray spectroscope studies indicate that the PtRu material comprises of complicated phases rather than a single alloy phase of Pt and Ru. The specific electrochemical surface area of the nanostructured powder measured using both CO and underpotential deposited Cu stripping techniques is 74–78 m² g^–1, higher than that of unsupported precious metal catalysts prepared using standard techniques. The combination of high surface area and periodic nanostructure of the templated PtRu makes it an interesting promising fuel cell electrocatalyst. This has been demonstrated by the high activity of the templated PtRu towards the methanol electrooxidation. Therefore the solid template route based on 3D mesoporous silica with controlled pore size and high pore interconnectivity provides an interesting alternative to produce promising high-surface-area electrode materials.     

Unique CO-tolerance of Pt–WOx materials

Well-defined tungsten-oxide-supported platinum nanoparticles (Pt/WO_x) were elaborated by impregnation-reduction of a platinum salt onto commercial monoclinic WO₃. Field-emission gun scanning electron microscopy (FEG-SEM) and transmission electron microscopy (TEM) revealed that the Pt particles are well-distributed on the oxide support, present a narrow particle size distribution centered on ca. 2–3 nm and a low degree of agglomeration. Carbon black was added to ensure electronic percolation in the electrodes during the electrochemical measurements. CO_ads electrooxidation currents were monitored at potentials as low as 0.1 V vs. RHE on Pt/WO_x, demonstrating high CO-tolerance compared to carbon-supported Pt or PtRu catalysts.     

Highly active PtRuFe/C catalyst for methanol electro-oxidation

High methanol electro-oxidation activity was obtained on novel PtRuFe/C (2:1:1 at.%) catalyst. Mass and specific activities were 5.67 A  g⁻¹ catal. and 177 mA m⁻² for the PtRuFe/C catalyst while those of the commercial PtRu/C catalyst were 2.28 A g⁻¹ catal. and 87.7 mA m⁻², respectively. CO stripping results showed that on-set voltage for CO electro-oxidation was lowered by incorporation of Fe. XRD and XPS results revealed that Fe₂O₃ was formed instead of Fe(0), which resulted in large electron deficiency in Pt and easy CO electro-oxidation. The electron deficiency of Pt was proved by XPS results of Pt4f peaks, which moved to higher binding energies in PtRuFe/C than PtRu/C.     

Promotion of PtRu/C anode catalysts for ethanol oxidation reaction by addition of Sn modifier

PtRu/C anode electrocatalysts modified by Sn were prepared for ethanol oxidation reaction (EOR). Their phase structures, surface species, surface compositions, and EOR activities were characterized by XRD, XPS, temperature-programmed reduction (TPR), and CV, respectively. It has been found that in the PtRu/Sn_xC and PtSn/C alloy catalysts, some Sn alloyed with Pt to form Pt–Sn phase existed as the metallic state, however, the excess Sn existed as the amorphous SnO or crystalline SnO₂. Surface analyses and electrochemical measurements suggest that the surface Ru and amorphous SnO instead of the crystalline SnO₂ are important species for the promotion of EOR. As a result, compared with PtSn/C, the I₀₆ was enhanced about 200% for the PtRu/C electrocatalyst with 10 wt% of Sn modification.     

Surface modified Pt/C as a methanol tolerant oxygen reduction catalyst for direct methanol fuel cells

A new procedure has been successfully developed by which PtN_x/C is synthesized to enhance methanol tolerance while maintaining a high catalytic activity for the oxygen-reduction reaction (ORR). The nitrogen-modified Pt surface, which is prepared using a chelating agent followed by heat treatment, exhibits considerable selectivity toward the ORR in the presence of methanol. The high methanol tolerance could be attributed to the suppression of methanol adsorption resulting from the modification of the Pt surface with nitrogen. A direct methanol fuel-cell (DMFC) test showed that a power density of up to 120 m W cm⁻² was generated when PtN_x/C was used as the cathode catalyst (1 mg cm⁻²) in 6 M methanol and oxygen at 70 °C.     

A novel vanadium oxide deposit for the cathode of asymmetric lithium-ion supercapacitors

Hydrous vanadium oxide (denoted as VO_x·yH₂O) deposited at 0.4 V shows promising capacitive behavior in aqueous media containing concentrated Li ions. VO_x·yH₂O annealed in air at 300 °C for 1 h shows highly reversible Li-ion intercalation/de-intercalation behavior with specific capacitance reaching ca. 737 and 606 F g^? 1 at 25 and 500 mV s^? 1 in 12 M LiCl between ?0.2 and 0.8 V. In 14 M LiCl, retention of specific capacitance is about 95% when the scan rate is increased from 25 to 500 mV s^? 1. This work is the first report showing the ultrahigh rate of Li-ion intercalation/de-intercalation in VO_x·yH₂O. A so-called Li-ion supercapacitor of the asymmetric type consisting of a VO_x^.yH₂O cathode and a WO₃^.zH₂O anode is proposed here.     

Novel method for the preparation of carbon supported nano-sized amorphous ruthenium oxides for supercapacitors

Nanostructured amorphous RuO₂ · xH₂O/C composite materials are prepared via a modified sol–gel process using glycolic acid. The glycolate anion, which dissociates from glycolic acid at pH 7, behaves as a stabilizer by adsorbing onto the RuO₂ · xH₂O surface, thus resulting in particles with a size of about 2 nm. As evidenced by zeta potential measurements, the surface charge of RuO₂ · xH₂O becomes more electronegative as the amount of glycolic acid increases. After heat treatment at 160 ^oC to remove the stabilizer, RuO₂ · xH₂O/C is found to exhibit an amorphous structure. The specific capacitance of RuO₂ · xH₂O/C particles (40 wt% Ru) prepared in the presence of glycolic acid (0.3 g L⁻¹) is 462 F g⁻¹, which is 30% higher than that of the material prepared in the absence of glycolic acid. Both the nanosized particles and the amorphous structure mainly contribute to this increase in the specific capacitance.     

Effect of sintering temperature and thermoelectric power studies of the system MgFe2−xCrxO4

Mixed metal oxides showing the spinel structure exhibit interesting structural and electrical properties. Substances with specific compositions in the system MgFe_2?xCr_xO₄ were synthesized by the simple co-precipitation method and have been investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM) to study the effect of temperature on the size of particles and grains. The infrared spectrum shows, two strong bands around 600 and 500 cm^?1. An elemental composition of one of the samples, MgFeCrO₄ was found by energy dispersive X-ray spectroscopy (EDS). The thermoelectric power measurements carried out from room temperature to 500 °C, show both n-type and p-type behavior.     

Electrode properties of Sr doped La2CuO4 as new cathode material for intermediate-temperature SOFCs

High performance La_2−xSr_xCuO_4−δ (x = 0.1, 0.3, 0.5) cathode materials for intermediate temperature solid oxide fuel cell (IT-SOFCs) were prepared and characterized. The investigation of electrical properties indicated that La_1.7Sr_0.3CuO₄ cathode has low area specific resistance (ASR) of 0.16 Ω cm² at 700 °C and 1.2 Ω cm² at 500 °C in air. The rate-limiting step for oxygen reduction reaction on La_1.7Sr_0.3CuO₄ electrode changed with oxygen partial pressure and measurement temperature. La_1.7Sr_0.3CuO₄ cathode exhibits the lowest overpotential of about 100 mV at a current density of 150 mA cm⁻² at 700 °C in air.     

A Raman scattering study of structural changes in LaMn1−xCoxO3+δ system

We present results of Raman scattering studies on LaMn_1−xCo_xO_3+δ over a wide range of doping content (x = 0.1–0.75) and temperature range of 20–300 K. Powder X-ray diffraction patterns show that there is a structural change from orthorhombic to rhombohedral at x = 0.5 as x increases. Raman spectra of all LaMn_1−xCo_xO_3+δ samples show peaks near 260, 500, and 650 cm⁻¹. However, the Raman spectra are not drastically different from each other across the structural phase transition at x = 0.5. On the other hand, the peak frequencies of the modes near 260 and 500 cm⁻¹ as functions of Co content (x) show slope changes at x = 0.5. The full-width at the half-maximum (FWHM) of the mode near 650 cm⁻¹ as a function of Co content (x) shows minimum at x = 0.5. Normally, larger values of FWHM are expected at near x = 0.5, if the mode were affected by the structural disorder at the phase boundary. Therefore, it is likely due to lowest charge concentration at x = 0.5, which results in lowest screening effect. This is consistent with the fact that the intensity of the phonons is strongest at x = 0.5. As the temperature decreases, the two peaks near 500 and 650 cm⁻¹ of different Co contents, related with octahedral distortions, are found to shift to lower frequencies unlike the usual temperature behavior. However, no abrupt change in the peak frequencies and the FWHM is observed across measured temperature range, regardless of the Co content.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Cu–Ni hetero-bimetallic compounds,Part 1: Preparation,structure and properties of [Cu0.05Ni0.95(bpy)2(ox)]·4H2O

New bimetallic compound [Cu_xNi_1?x(bpy)₂(ox)]·4H₂O (x = 0.05, ox = oxalato, bpy = 2,2′-bipyridine) was synthesized and chemically characterized. Its crystal structure is molecular. The octahedron around the metal central atom is deformed due to coordination by one bidentate oxalate anion and two bpy ligands. There are four uncoordinated water molecules in the asymmetric unit. The metal site is occupied by both Cu(II) and Ni(II) atoms in the 5:95 ratio. The complex molecules interact with water molecules through hydrogen bonds and, moreover, π–π interactions between aromatic rings lead to a 1D arrangement of molecules. The susceptibility data measured down to 2 K were analyzed using strong-coupling theory and the best agreement with the experimental data were found for g = 2.1, D/k = 5.6, E/k = 0.35, J/k = 0.2. The dehydration starts at 30 °C. As a final product of its thermal decomposition a solid solution of Cu_xNi_1?xO was detected by X-ray powder diffraction.     

Synthesis of coin-like hollow carbon and performance as Pd catalyst support for methanol electrooxidation

The coin-like hollow carbon (CHC) has been synthesized by only using ethanol as the carbon source with a novel Mg/NiCl₂ catalytic system via a facile solvothermal method for the first time. The CHC synthesized at optimized conditions shows an average thickness of less than 154 nm and the coin diameter of 1–3 μm. The CHC is characterized by SEM, TEM, XRD and electrochemical techniques. Pd on CHC (denotes as Pd/CHC) electrocatalysts are prepared for methanol oxidation in alkaline media. The Pd/CHC electrocatalyst gives a mass activity of 2930 A g⁻¹ Pd for methanol oxidation against 870 A g⁻¹ Pd on Pd/C electrocatalyst. One main reason for the higher mass activity of the Pd/CHC is the higher electrochemical active surface area (EASA) of the Pd/CHC.     

Phase transitions of CaTiO3 ceramics sintered with the aid of NaF and MgF2

New phases with initial composition (1 ? x)CaTiO₃ ? xNaF ? xMgF₂ (0 ≤ x ≤ 0.20) have been prepared at low temperature (950 °C) from mixtures of CaTiO₃ and fluorides NaF and MgF₂. The oxyfluorides obtained have been characterized by X-ray diffraction at room temperature and indexed by isotypy with orthorhombic CaTiO₃. The microstructures of these phases are observed by scanning electron microscopy. Dielectric measurements have been carried out during cooling cycle from 500 °C to room temperature at two frequencies (100 Hz, 1 kHz). Differential scanning calorimetry (DSC), thermogravimetry (TG) and differential thermogravimetry (DTG) analyses have been performed, respectively, from room temperature up to 550 °C (DSC) and 920 °C (TG–DTG). The dielectric measurements revealed two anomalies which have been confirmed by DSC analyses. These phenomena are ascribed to second order phase transitions. The variation of the real permittivity with temperature is in agreement with the class I capacitor specifications. However, the dielectric losses have to be improved.     

Fabrication of highly conductive Ru/a-CNx:H composite films by anode deposit

Ruthenium(0) composite hydrogenated amorphous carbon nitride (Ru/a-CN_x:H) films were deposition on single crystal silicon (1 0 0) substrate by electrochemical deposition technique with acetonitrile as carbon source, and Ru₃(CO)₁₂ as dopant. In the deposited progress, the Si (1 0 0) acted as anode. The relative atomic ratio of Ru/N/C was about 0.28/0.33/1, and Ru nanocrystalline particles about 8 nm were homogeneously dispersed into the amorphous carbon matrix. After doping Ru into a-CN_x:H films, the conductivity of the films were evidently improved and the resistivity drastically decrease from 10⁸ Ω cm to about 100 Ω cm.     

Enhanced stability and activity of PtRu nanotubes for methanol electrooxidation

PtRu 1D nanostructures on titanium are prepared and analysed as electrocatalysts for methanol electrooxidation. The morphology and composition of the 1D nanostructure are characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). The electrocatalytic properties of such catalysts for methanol oxidation are investigated by cyclic voltammetry (CV) and chronoamperometry (CA) in 1.0 M CH₃OH + 0.5 M H₂SO₄ aqueous solution. The results show that Pt₄₆Ru₅₄ nanotubes yields to a five-fold improvement of the mass specific activity and to a three-fold improvement of the long-term poisoning rate as compared to PtRu black of similar composition.     

Preparation via microemulsion method and proton conduction at intermediate-temperature of BaCe1−xYxO3−α

The ceramic powders of BaCe_1?xY_xO_3?α (x = 0.05, 0.10, 0.15, 0.20) have been prepared via a microemulsion method. Green compacts of the powders were sintered to densities higher than 95% of theoretical at the lower temperature (1500 °C). The obtained ceramics showed a single-phase of orthorhombic perovskite. The proton conduction was investigated by employing the techniques of AC impedance and electrochemical hydrogen permeation (hydrogen pumping) at 300–600 °C. It was found that the ceramics were almost pure proton conductors in wet hydrogen, and the highest proton conductivity was observed for x = 0.15 at 600 °C. Ammonia was synthesized successfully from nitrogen and hydrogen at atmospheric pressure in the electrolytic cell using BaCe_0.85Y_0.15O_3?α. The maximum rate of NH₃ formation was found to be 2.1 × 10^?9 mol s^?1 cm^?2 at 500 °C with an applied current of 0.75 mA.     

Synthesis and magnetic properties of heptadecametallic Fe(III) clusters

Heptadecametallic, all-ferric pieces of molecular magnetite of general formula HL_x[Fe₁₇O₁₆(OH)₁₂(L)₁₂Br₄]Br_3+x (L = β-picoline, isoquinoline, 3,5-lutidine; x = 0, 1) are made by the simple dissolution of FeBr₃ in L. The β-picoline (or equivalent) molecules act simultaneously as solvent, base and capping ligand. The resultant structure consists of a metal–oxygen core containing both octahedral and tetrahedral Fe(III) ions that is the exact analogue of the metal–oxygen positions seen in the magnetite lattice. Antiferromagnetic exchange between the tetrahedral and octahedral Fe(III) ions lead to the stabilization of an S = 35/2 spin ground state.