Indium tin oxide surface treatments for improvement of organic light-emitting diode performance

We have systematically investigated the influence of UV ozone and acid (HCl) treatments (separate and combined) of the surface of indium tin oxide (ITO) on the ITO parameters and the performance of organic light-emitting diodes (OLEDs) fabricated on the treated substrates. The ITO substrates were characterized by Hall measurements, Seebeck coefficient measurements and surface-probe microscopy. After ITO characterization, two types of devices (ITO/NPB/rubrene/Alq₃/LiF/Al and ITO/TPD/rubrene/Alq₃/LiF/Al) were fabricated on the differently treated substrates. It was found that in both cases the optimal treatment was HCl followed by UV ozone, which resulted in the lowest turn-on voltage and the highest luminous efficiency. The maximum luminous efficiency in the ITO/NPB/rubrene/Alq₃/LiF/Al OLED with HCl followed by UV ozone treatment was 2.15 lm/W compared to 1.46 lm/W with UV ozone treatment only. PACS 81.65Cf; 85.60.Jb     

Hole-transporting property of a chemically hybridized poly(vinylcarbazole)-fullerene

We synthesized a star copolymer of poly(vinylcarbazole) (PVK) branched from a fullerene (C₆₀) center, and investigated its optical absorption and photoluminescence properties. The chemically hybridized PVK-C₆₀ was then employed as a hole-transporting layer of the electroluminescent device with a poly(9,9^′-dihexylfluorene-2,7-divinylene-m-phenylenevinylene-stat-p-phenylenevinylene) (CPDHFPV) emitting layer. The ITO/PVK-C₆₀/CPDHFPV/LiF/Al device showed a strong electroluminescence quenching due to a direct contact of the PVK-C₆₀ and the CPDHFPV layers. In contrast, when an additional PVK layer was introduced between the two layers, the electroluminescence was largely enhanced. The emitted light power of the ITO/PVK-C₆₀/PVK/CPDHFPV/LiF/Al device was improved by 3 times compared with the device without the PVK-C₆₀ layer.     

Influence of tetrabutylammonium hexafluorophosphate (TBAPF6) doping level on the performance of organic light emitting diodes based on PVK:PBD blend films

The effect of doping level of tetrabutylammonium hexafluorophosphate (TBAPF₆) on the performance of single-layer organic light emitting diodes (OLEDs) with ITO/PVK:PBD:TBAPF₆/Al structure were investigated where indium tin oxide (ITO) was used as anode, poly(9-vinylcarbazole) (PVK) as hole-transporting polymeric host, 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole (PBD) as electron-transporting molecule and aluminium (Al) as cathode. It was found that the doped devices underwent a unique transition at the first voltage scan as indicated by drastically increasing of current at certain applied voltage. After the transition, the threshold voltage for current injection as well as the turn-on voltage decreased significantly as compared to the undoped device. The current injection threshold voltage and turn-on voltage decreased with the increase of TBAPF₆ doping level. More importantly, a relatively low current injection threshold voltage of 3 V has been achieved by doping a significant amount of TBAPF₆ (weight ratio greater than five) in the single-layer OLED based on PVK:PBD blend films with high work function Al metal as cathode. The significant improvement was attributed to the reduction of both electron and hole injection energy barriers caused by accumulation of ionic species at the interface.     

Influence of the deposition temperature on the structure and performance of tris(8-hydroxyquinoline) aluminum based flexible organic light-emitting devices

Based on indium tin oxide (ITO)/N,N′diphenyl-N-N′-di(m-tdyl) benzidine (TPD)/Alq₃/Al structure, flexible OLEDs on polyethylene terephthalate (PET) substrates were fabricated by physical vapor deposition (PVD) method. Tris(8-hydroxyquinoline)aluminum (Alq₃) films were deposited at 90, 120 and 150 °C to examine the influence of the deposition temperature on the structure and performance of OLEDs. Electroluminescence (EL) spectra and current-voltage-luminance (I-V-L) characteristics of the OLEDs were examined. It was found that the device fabricated at a high temperature had a higher external efficiency and longer lifetime. Atomic force microscope (AFM) was adopted to characterize the surface morphology of ITO/TPD/Alq₃. The higher uniform morphology of the Alq₃ formed at high temperature might contribute to the performance improvement of the OLEDs.     

White-light-emitting devices based on Nile Red and π electron rich [Zn<Subscript>4core</Subscript>] complex

A white organic light-emitting device was fabricated with a structure of ITO/PEDOT: PSS (45 nm)/PVK: Nile Red: [Zn_4core] (75 nm)/BCP (25 nm)/Al. Without Nile Red green and with Nile Red white emission was achieved. When the concentration of the Nile Red in thin film increased from 0.01 to 0.5 wt%, a white emission achieved. The electroluminescence spectra of the device cover a wide range of visible region with two peaks around 501 and 618 nm. It is noteworthy that a white and pure white OLEDs with an incomplete energy transfer from the green host [Zn_4core] to the dopant (Nile Red) was obtained in this work using a single emissive layer relative to the multi layered light emitter ones in white OLED devices. For 0.1 doped device, a maximum luminance efficiency of 2.54 cd/A with CIE coordinates of (x, y = 0.35, 0.37) at 230 mA/cm² has was achieved.     

The roles of zinc selenide sandwiched between organic layers and its applications in white light-emitting diodes

In this paper, the roles of zinc selenide (ZnSe) sandwiched between organic layers, i.e. organic/ZnSe/aluminum quinoline (Alq₃), have been studied by varying device structure. A broad band emission was observed from ITO/poly(N-vinylcarbazole)(PVK)(80 nm)/ZnSe(120 nm)/ Alq₃(15 nm)/Al under electric fields and it combined the emissions from the bulk of PVK, ZnSe and Alq₃, however, emission from only Alq₃ was observed from trilayer device ITO/N,N^′-bis-(1-naphthyl)-N,N^′-diphenyl-1, 1^′-biphenyl-4, 4^′-diamine (NPB) (40 nm)/ZnSe(120 nm)/ Alq₃(15 nm)/Al. Consequently the luminescence mechanism in the ZnSe layer is suggested to be charge carrier injection and recombination. By thermal co-evaporating Alq₃ and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), we get white light emission with a Commission Internationale de l’E clairage (C.I.E) co-ordinates of (0.32, 0.38) from device ITO/PVK(80 nm)/ZnSe(120 nm)/ Alq₃:DCJTB(0.5 wt% DCJTB)(15 nm)/Al at 15 V and the device performs stably with increasing applied voltages.     

Enhanced electroluminescence of Eu by Tb in complexes Tb1−xEux(TTA)3Dipy

A series of rare earth ternary compounds of Tb_1−xEu_x(TTA)₃Dipy (HTTA=thenoyltrifluoroacetone, Dipy=2,2′-dipyridyl) have been synthesized, and the characteristics of the compounds have been performed by DTA-TG, IR, UV and fluorescence spectroscopy. Photoluminescence measurements indicated that the complexes of Eu(III) emit strong red luminescence under UV radiation. IR spectra suggest that complexes have been successfully synthesized, and TG curves indicate that the complexes are stable up to a temperature of about 220 °C. The Eu complex was blended with poly(N-vinylcarbazole) (PVK) and spin coated into films, and electroluminescence devices with the structure of Indium Tin Oxide (ITO)/PVK:Tb_1−xEu_x(TTA)₃Dipy/BCP(2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline)/aluminum quinoline (AlQ)/Al were fabricated, the luminescence of Eu³⁺ complexes enhances after doping with Tb³⁺. Therefore, it may be an effective method to improve the EL intensity of the lanthanide complex.     

The effects of sodium in ITO by pulsed laser deposition on organic light-emitting diodes

The depth profile of ITO on glass was measured by the time-of-flight secondary ion mass spectroscopy (TOFSIMS) which revealed high sodium (Na) ion concentration at the ITO surface as well as at the ITO–glass interface as a result of out diffusion with substrate heating. Effects of Na ions on the performance of organic light-emitting diode (OLED) were studied by etching away a few tens of nanometers off the ITO surface with a dilute aquaregia solution of HNO₃:HCl:H₂O. A single-layer, molecularly doped ITO/(PVK+TPD+Alq₃)/Al OLEDs were fabricated on bare and etched ITO samples. Although the removal of a 10-nm layer of ITO surface increased the voltage range, brightness, and lifetime, it was insufficient to correlate these improvements with solely to the Na ion reduction without considering the surface roughness.     

芴-咔唑新型共聚物/PVK掺杂体系的电致发光特性研究

研究了新型的芴-咔唑共聚物(PFC)与聚乙烯咔唑(PVK)掺杂体系的光致发光和电致发光特性.制备了结构分别为indium-tin-oxide(ITO)/PVK:PFC/bathocuproine(BCP)/tris-(8-hydroxylquinoline)-aluminum (Alq₃) /Mg:Ag，ITO/PFC/BCP/Alq₃/Mg∶Ag和ITO/PVK/BCP/Alq₃/Mg∶Ag的三种有机电致发光器件.对器件的光电特性进行了测试.结果表明，掺杂体系中的PVK有效地抑制了固态膜中PFC激基缔合物的形成.掺杂器件在不同的外加电场作用下发生发光层位置的移动，通过调节外加电场，可以获得从绿光到蓝光的可见光发射.当外加电压大于7V时，掺杂器件的蓝色发光亮度达到1650cd/m²，推测其中可能存在从PVK到PFC的能量传递过程.     

Ultraviolet photoelectron spectroscopy investigation of interface formation in an indium-tin oxide/fluorocarbon/organic semiconductor contact

It has been demonstrated that hole-injection in organic light-emitting devices (OLEDs) can be enhanced by inserting a UV-illuminated fluorocarbon (CF_x) layer between indium-tin oxide (ITO) and organic hole-transporting layer (HTL). In this work, the process of interface formation and electronic properties of the ITO/CF_x/HTL interface were investigated with ultraviolet photoelectron spectroscopy. It was found that UV-illuminated fluorocarbon layer decreases the hole-injection barrier from ITO to α-napthylphenylbiphenyl diamine (NPB). Energy level diagrams deduced from the ultraviolet photoelectron spectroscopy (UPS) spectra show that the hole-injection barrier in ITO/UV-treated CF_x/NPB is the smallest (0.46 eV), compared to that in the ITO/untreated CF_x/NPB (0.60 eV) and the standard ITO/NPB interface (0.68 eV). The improved current density-voltage (I-V) characteristics in the UV-treated CF_x-coated ITO contact are consistent with its smallest barrier height.     

Wetting and superhydrophobic properties of PECVD grown hydrocarbon and fluorinated-hydrocarbon coatings

Wetting characteristics of micro-nanorough substrates of aluminum and smooth silicon substrates have been studied and compared by depositing hydrocarbon and fluorinated-hydrocarbon coatings via plasma enhanced chemical vapor deposition (PECVD) technique using a mixture of Ar, CH₄ and C₂F₆ gases. The water contact angles on the hydrocarbon and fluorinated-hydrocarbon coatings deposited on silicon substrates were found to be 72° and 105°, respectively. However, the micro-nanorough aluminum substrates demonstrated superhydrophobic properties upon coatings with fluorinated-hydrocarbon providing a water contact angle of ∼165° and contact angle hysteresis below 2° with water drops rolling off from those surfaces while the same substrates showed contact angle of 135° with water drops sticking on those surfaces. The superhydrophobic properties is due to the high fluorine content in the fluorinated-hydrocarbon coatings of ∼36 at.%, as investigated by X-ray photoelectron spectroscopy (XPS), by lowering the surface energy of the micro-nanorough aluminum substrates.     

The effect of driving voltage on the electroluminescent property of a blend of poly(9-vinylcarbazole) and 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole

The impact of driving voltage on the electroluminescence (EL) from organic light emitting diode with ITO/PVK:PBD:TBAPF₆(10:10:1)/Al structure was analyzed by the method of Gaussian fitting. Indium tin oxide (ITO) was used as anode, poly(9-vinylcarbazole) (PVK) as polymeric host, 2-(4-biphenylyl)-5-phenyl-1,3,4-oxadiazole (PBD) as electron-transporting molecule, tetrabutylammonium hexafluorophosphate (TBAPF₆) as organic salt and aluminium (Al) as cathode. A broad EL has been observed and it could be attributed to the overlap of emission from four different excited state complexes, including PVK:PBD exciplex, PVK:PBD electroplex, PBD electromer and PVK electromer. The EL spectra shifted to longer wavelength with the increase of driving voltage. The ratio of PVK electromer to PVK:PBD exciplex emission intensity first declined slightly and then increased remarkably, while the relative intensity of combination of PVK:PBD electroplex and PBD electromer emission remained unchanged when the voltage was increased.     

Spectral studies of thin films based on poly(N-vinylcarzole) and red dopant

Organic light-emitting diodes were fabricated with a structure of indium-tin-oxide (ITO)/poly(N-vinylcarzole)(PVK):4-(dicyanom-ethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB)/8-tris-hydroxyquinoline aluminum (Alq₃)/lithium fluoride (LiF)/Al. The energy transfer from PVK to Alq₃ then to DCJTB and the charge trapping processes were investigated by employing the photoluminescence (PL) and electroluminescence (EL) spectra. With increasing thickness of the Alq₃ layer, the PL and EL emission from PVK were decreased gradually, which indicated that the effective energy transfer occurred from PVK to Alq₃ and then from Alq₃ to DCJTB. At the same time, we found that the exciton recombination zone could be adjusted by controlling the Alq₃ layer thickness and the applied voltages. The effects of different DCJTB concentrations on the optical and electrical characteristics of the devices were investigated, and an obvious red-shift was observed with the DCJTB dopant concentrations increasing in the PL and EL spectra.     

Transparent water repellent silica films by sol-gel process

Non-wettable surfaces with high contact angles and facile sliding angle of water droplets have received tremendous attention in recent years. The present paper describes the room temperature (∼27 °C) synthesis of dip coated water repellent silica coatings on glass substrates using iso-butyltrimethoxysilane (iso-BTMS) as a co-precursor. Emphasis is given to the influence of the hydrophobic reagent (iso-BTMS) on the water repellent properties of the silica films. Silica sol was prepared by keeping the molar ratio of tetraethoxysilane (TEOS) precursor, methanol (MeOH) solvent, water (H₂O) constant at 1:16.53:8.26 respectively, with 0.01 M NH₄F throughout the experiment and the molar ratio of iso-BTMS/TEOS (M) was varied from 0 to 0.965. The effect of M on the surface structure and hydrophobicity has been researched. The static water contact angle values of the silica films increased from 65° to 140° and water sliding angle values decreased from 42° to 16° with an increase in the M value from 0 to 0.965. The water repellent silica films are thermally stable up to a temperature of 280 °C and above this temperature the film shows hydrophilic behavior. The water repellent silica films were characterized by the Fourier Transform Infrared (FT-IR) Spectroscopy, Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), % of optical transmission, thermal and chemical aging tests, humidity tests, static and dynamic water contact angle measurements.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Diffusion study of multi-organic layers in OLEDs by ToF-SIMS

A model organic light-emitting diodes (OLEDs) with structure of tris(8-hydroxyquinoline) aluminum (Alq₃)/N,N′-diphenyl-N,N′-bis[1-naphthy-(1,1′-diphenyl)]-4,4′-diamine (NPB)/indium tin oxide (ITO)-coated glass was fabricated for diffusion study by ToF-SIMS. The results demonstrate that ToF-SIMS is capable of delineating the structure of multi-organic layers in OLEDs and providing specific molecular information to aid deciphering the diffusion phenomena. Upon heat treatment, the solidity or hardness of the device was reduced. Complicated chemical reaction might occur at the NPB/ITO interface and results in the formation of a buffer layer, which terminates the upper diffusion of ions from underlying ITO.     

Biomimetic, hierarchical structures on polymer surfaces by sequential imprinting

Thermal nanoimprint lithography (NIL) is based on the thermo-mechanical deformation of a polymer film above the glass transition temperature (T_g) and at an applied pressure. Sequential imprinting extends the process of thermal NIL to create hierarchical structures by carrying out secondary and tertiary imprintings at temperatures below the T_g of a polymer. In this work, we demonstrate the use of sequential imprinting technique to fabricate two- and three-level hierarchical structures on polystyrene (PS) and poly(methyl methacrylate) (PMMA) films over a temperature range of 70-130 °C, with the aim to mimic the hierarchical structures found in biological systems. By mimicking the hierarchical structure in a plant leaf, the water contact angle of PS film was increased from 95° to 128°, while the water contact angle of PMMA film was increased from 71° to 104°, without any chemical treatment.     

Improved performance of organic light-emitting devices with plasma treated ITO surface and plasma polymerized methyl methacrylate buffer layer

Transparent indium-tin-oxide (ITO) anode surface was modified using O₃ plasma and organic ultra-thin buffer layers were deposited on the ITO surface using 13.56 MHz rf plasma polymerization technique. A plasma polymerized methyl methacrylate (ppMMA) ultra-thin buffer layer was deposited between the ITO anode and hole transporting layer (HTL). The plasma polymerization of the buffer layer was carried out at a homemade capacitively coupled plasma (CCP) equipment. N,N′-Diphenyl-N,N′-bis(3-methylphenyl)-1,1′-diphenyl-4,4′-diamine (TPD) as HTL, Tris(8-hydroxy-quinolinato)aluminum (Alq₃) as both emitting layer (EML)/electron transporting layer (ETL), and aluminum layer as cathode were deposited using thermal evaporation technique. Electroluminescence (EL) efficiency, operating voltage and stability of the organic light-emitting devices (OLEDs) were investigated in order to study the effect of the plasma surface treatment of the ITO anode and role of plasma polymerized methyl methacrylate as an organic ultra-thin buffer layer.     

Biocompatibility of polypropylene non-woven fabric membrane via UV-induced graft polymerization of 2-acrylamido-2-methylpropane sulfonic acid

This work described the graft polymerization of a sulfonic acid terminated monomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS), onto the surface of polypropylene non-woven (NWF PP) membrane by O₂ plasma pretreatment and UV-induced photografting method. The chemical structure and composition of the modified surfaces were analyzed by FTIR-ATR and XPS, respectively. The wettability was investigated by water contact angle and equilibrium water adsorption. And the biocompatibility of the modified NWF PP membranes was evaluated by protein adsorption and platelet adhesion. It was found that the graft density increased with prolonging UV irradiation time and increasing AMPS concentration; the water contact angles of the membranes decreased from 124° to 26° with the increasing grafting density of poly(AMPS) from 0 to 884.2 μg cm⁻², while the equilibrium water adsorption raised from 5 wt% to 75 wt%; the protein absorption was effectively suppressed with the introduction of poly(AMPS) even at the low grafting density (132.4 μg cm⁻²); the number of platelets adhering to the modified membrane was dramatically reduced when compared with that on its virgin surface. These results indicated that surface modification of NWF PP membrane with AMPS was a facile approach to construct biocompatible surface.     

Fabrication of superhydrophobic polyurethane/organoclay nano-structured composites from cyclomethicone-in-water emulsions

Nano-structured polyurethane/organoclay composite films were fabricated by dispersing moisture-curable polyurethanes and fatty amine/amino-silane surface modified montmorillonite clay (organoclay) in cyclomethicone-in-water emulsions. Cyclomethicone Pickering emulsions were made by emulsifying decamethylcyclopentasiloxane (D₅), dodecamethylcyclohexasiloxane (D₆) and aminofunctional siloxane polymers with water using montmorillonite particles as emulsion stabilizers. Polyurethane and organoclay dispersed emulsions were spray coated on aluminum surfaces. Upon thermosetting, water repellent self-cleaning coatings were obtained with measured static water contact angles exceeding 155° and low contact angle hysteresis (<8°). Electron microscopy images of the coating surfaces revealed formation of self-similar hierarchical micro- and nano-scale surface structures. The surface morphology and the coating adhesion strength to aluminum substrates were found to be sensitive to the relative amounts of dispersed polyurethane and organoclay in the emulsions. The degree of superhydrophobicity was analyzed using static water contact angles as well as contact angle hysteresis measurements. Due to biocompatibility of cyclomethicones and polyurethane, developed coatings can be considered for specific bio-medical applications.