Determination of organic and inorganic mercury species in water and sediment samples by HPLC on-line coupled with ICP-MS

This paper describes a preconcentration method for Hg²⁺ and MeHg⁺ in water samples using sodium diethyldithiocarbamate immobilized in polyurethane foam (PU-NaDDC) and an extraction method for several mercury species in sediment samples, including MeHg⁺, EtHg⁺ and PhHg⁺, which is simple, rapid, and uses a single organic solvent. Separation and measurement were done by high-performance liquid chromatography on-line with inductively coupled plasma mass spectrometry (HPLC/ICP-MS). Initially, the test of recovery was applied using procedures compatible with HPLC. Under the optimum extraction conditions, recoveries of 96.7, 96.3 and 97.3% were obtained for MeHg⁺, EtHg⁺, and PhHg⁺, respectively, from n = 4 spiked sediment samples. This study also demonstrates that the combination of solid-phase extraction on PU-NaDDC with HPLC separation and ICP-MS detection is an effective preconcentration procedure for simultaneous measurement of Hg²⁺ and MeHg⁺ at ultra-trace levels in water samples. The application of the proposed procedure to the determination of mercury species in drinking water sample was investigated. The proposed method clearly gave satisfactory average recoveries between 93.7 and 101.5%.     

Non-chromatographic screening method for the determination of mercury species. Application to the monitoring of mercury levels in Antarctic samples

A simple non-chromatographic method for the determination of mercury (Hg²⁺), methylmercury (MeHg⁺), dimethylmercury (Me₂Hg), and phenylmercury (PhHg⁺) employing atomic fluorescence spectrometry (AFS) as detection technique was developed. Mercury species showed a particular behavior in the presence of several reagents. In a first stage SnCl₂ was employed for Hg²⁺ determination; in a second step, [Hg²⁺ + PhHg⁺] concentration was determined using SnCl₂ and UV radiation. MeHg⁺ decomposition was prevented adding 2-mercaptoethanol. In a third stage, [Hg²⁺ + PhHg⁺ + MeHg⁺] concentration was determined using K₂S₂O₈. Finally, the four species were determined employing NaBH₄. Reagents concentration and flow rates were optimized. The extraction technique of mercury species involved the use of 2-mercaptoethanol as ion-pair reagent. The limits of detection for Hg²⁺, PhHg⁺, MeHg⁺, and Me₂Hg were 1, 40, 68, and 99 ng L⁻¹ with a relative standard deviation of 1.5, 3.1, 4.7 and 5.8%, respectively. Calibration curve was linear with a correlation factor equal to 0.9995. The method was successfully applied to the determination of the mercury species in two Antarctic materials: IRMM 813 (Adamussium colbecki) and MURST-ISS-A2 (Antarctic Krill).     

Liquid-phase microextraction with in-drop derivatization combined with microvolume fluorospectrometry for free and hydrolyzed formaldehyde determination in textile samples

A novel approach for preconcentration and speciation analysis of trace amount of mercury from water samples was proposed by dispersive liquid–liquid microextraction (DLLME) coupled to high performance liquid chromatography with diode array detection (HPLC-DAD). Mercury species (Hg²⁺, methylmercury (MeHg⁺) and phenylmercury (PhHg⁺)) were complexed with dithizone (DZ) to form hydrophobic chelates and then extracted into the fine drops of extraction solvent dispersed in the aqueous sample by dispersive solvent. After extraction, the sedimented phase was analyzed by HPLC-DAD. Some important parameters affecting the DLLME such as extraction solvent and dispersive solvent type and volume, concentration of dithizone solution, sample pH, extraction time and salt effect were investigated. Ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIM][PF₆]) was found to be a suitable extractant for the chelates. Under the optimized conditions (extraction solvent: 70 μL of ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate ([HMIM][PF₆]); dispersive solvent: 0.75 mL of methanol containing dithizone (0.02%, m/v); pH: 4; extraction time: 5 min; and without salt addition), the limits of detection for Hg²⁺, MeHg⁺ and PhHg⁺ were 0.32, 0.96 and 1.91 μg L⁻¹ (S N⁻¹ = 3) respectively, and the relative standard deviation (RSD) was between 4.1 and 7.3% (n = 5). Three real water samples (tap water, river water and lake water) spiked with mercury species were detected by the developed method, and the relative recoveries obtained for Hg²⁺, MeHg⁺ and PhHg⁺ were 89.6–101.3%, 85.6–102.0% and 81.3–97.6%, respectively.     

Ionic liquids dispersive liquid–liquid microextraction and HPLC‐atomic fluorescence spectrometric determination of mercury species in environmental waters

An ionic liquid (IL) based dispersive liquid–liquid microextraction combined with HPLC hydride generation atomic fluorescence spectrometry method for the preconcentration and determination of mercury species in environmental water samples is described. Four mercury species (MeHg⁺, EtHg⁺, PhHg⁺, and Hg²⁺) were complexed with dithionate and the neutral chelates were extracted into IL drops using dispersive liquid–liquid microextraction. Variables affecting the formation and extraction of mercury dithizonates were optimized. The optimum conditions found were as follows: IL‐type and amount, 0.05 g of 1‐octyl‐3‐methylimidazolium hexafluorophosphate; dispersive solvents type and amount, 500 μL of acetone; pH, 6; extraction time, 2 min; centrifugation time, 12 min; and no sodium chloride addition. Under the optimized conditions, the detection limits of the analytes were 0.031 μg/L for Hg²⁺, 0.016 μg/L for MeHg⁺, 0.024 μg/L for EtHg⁺, and 0.092 μg/L for PhHg⁺, respectively. The repeatability of the method, expressed as RSD, was between 1.4 and 5.2% (n = 10), and the average recoveries for spiked test were 96.9% for Hg²⁺, 90.9% for MeHg⁺, 90.5% for EtHg⁺, 92.3% for PhHg⁺, respectively. The developed method was successfully applied for the speciation of mercury in environmental water samples.     

Improvement of analytical performances for mercury speciation by on-line derivatization, cryofocussing and atomic fluorescence spectrometry

A modified automated on-line hyphenated system for simultaneous inorganic ionic mercury (Hg²⁺) and monomethylmercury (MeHg⁺) analysis by hydride generation (HG) or ethylation (Eth), cryofocussing, gas chromatography (GC) separation and atomic fluorescence spectrometry (AFS) detection has been improved. Both derivatization methods are investigated with respect to the chromatographic and analytical performances. They can be both affected by interferences when the AFS detection system is used. Water vapor removal using a soda lime moisture trap improves significantly the chromatographic performances, the reproducibility and the detection limits for Hg²⁺ and MeHg⁺ analyzed with both methods. For ethylation (Eth) derivatization, a scattering interference generated from low-quality ethylation reagent has also been eliminated. For HG, improved detection limits are 0.13 ng l⁻¹ and 0.01 ng l⁻¹ for Hg²⁺ and MeHg⁺, respectively (0.1 l water sample), and reproducibility are 5% for Hg²⁺ (20 ng l⁻¹) and MeHg⁺ (5 ng l⁻¹). Improved detection limits for Eth are 0.22 ng g⁻¹ for Hg²⁺ and 0.02 ng g⁻¹ for MeHg⁺ (1 g dry sediment sample) and the reproducibility are 5-6% for Hg²⁺ and MeHg⁺ (1-2 ng g⁻¹).     

Speciation of mercury in water samples by dispersive liquid-liquid microextraction combined with high performance liquid chromatography-inductively coupled plasma mass spectrometry

The dispersive liquid-liquid microextraction (DLLME) combined with high performance liquid chromatography-inductively coupled plasma mass spectrometry for the speciation of mercury in water samples was described. Firstly methylmercury (MeHg⁺) and mercury (Hg²⁺) were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors of 138 and 350 for MeHg⁺ and Hg²⁺ were obtained from only 5.00 mL sample solution. The detection limits of the analytes (as Hg) were 0.0076 ng mL⁻¹ for MeHg⁺ and 0.0014 ng mL⁻¹ for Hg²⁺, respectively. The relative standard deviations for ten replicate measurements of 0.5 ng mL⁻¹ MeHg⁺ and Hg²⁺ were 6.9% and 4.4%, respectively. Standard reference material of seawater (GBW(E)080042) was analyzed to verify the accuracy of the method and the results were in good agreement with the certified values. Finally, the developed method was successfully applied for the speciation of mercury in three environmental water samples.     

Speciation of mercury by ionic liquid-based single-drop microextraction combined with high-performance liquid chromatography-photodiode array detection

Room temperature ionic liquids can be considered as environmentally benign solvents with unique physicochemical properties. Ionic liquids can be used as extractant phases in SDME, being compatible with chromatographic systems. A single-drop microextraction method was developed for separation and preconcentration of mercury species (MeHg⁺, EtHg⁺, PhHg⁺ and Hg²⁺), which relies on the formation of the corresponding dithizonates and microextraction of these neutral chelates onto a microdrop of an ionic liquid. Afterwards, the separation and determination were carried out by high-performance liquid chromatography with a photodiode array detector. Variables affecting the formation and extraction of mercury dithizonates were optimized. The optimum conditions found were: microextraction time, 20 min; stirring rate, 900 rpm; pH, 11; ionic liquid type, 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]); drop volume, 4 μL; and no sodium chloride addition. Limits of detection were between 1.0 and 22.8 μg L⁻¹ for the four species of mercury, while the repeatability of the method, expressed as relative standard deviation, was between 3.7 and 11.6% (n = 8). The method was finally applied to the determination of mercury species in different water samples.     

Sequential cloud point extraction for the speciation of mercury in seafood by inductively coupled plasma optical emission spectrometry

A novel nonchromatographic speciation technique for the speciation of mercury by sequential cloud point extraction (CPE) combined with inductively coupled plasma optical emission spectrometry (ICP-OES) was developed. The method based on Hg²⁺ was complexed with I⁻ to form HgI₄²⁻, and the HgI₄²⁻ reacted with the methyl green (MG) cation to form hydrophobic ion-associated complex, and the ion-associated complex was then extracted into the surfactant-rich phase of the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114), which are subsequently separated from methylmercury (MeHg⁺) in the initial solution by centrifugation. The surfactant-rich phase containing Hg(II) was diluted with 0.5 mol L^− 1 HNO₃ for ICP-OES determination. The supernatant is also subjected to the similar CPE procedure for the preconcentration of MeHg⁺ by the addition of a chelating agent, ammonium pyrrolidine dithiocarbamate (APDC), in order to form water-insolvable complex with MeHg⁺. The MeHg⁺ in the micelles was directly analyzed after disposal as describe above. Under the optimized conditions, the extraction efficiency was 93.5% for Hg(II) and 51.5% for MeHg⁺ with the enrichment factor of 18.7 for Hg(II) and 10.3 for MeHg⁺, respectively. The limits of detection (LODs) were 56.3 ng L^− 1 for Hg(II) and 94.6 ng L^− 1 for MeHg⁺ (as Hg) with the relative standard deviations (RSDs) of 3.6% for Hg(II) and 4.5% for MeHg⁺ (C = 10 μg L⁻¹, n = 7), respectively. The developed technique was applied to the speciation of mercury in real seafood samples and the recoveries for spiked samples were found to be in the range of 93.2–108.7%. For validation, a certified reference material of DORM-2 (dogfish muscle) was analyzed and the determined values are in good agreement with the certified values.     

Speciation analysis of mercury in sediments, zoobenthos and river water samples by high-performance liquid chromatography hyphenated to atomic fluorescence spectrometry following preconcentration by solid phase extraction

A high-pressure microwave digestion was applied for microwave-assisted extraction (MAE) of mercury species from sediments and zoobenthos samples. A mixture containing 3 mol L⁻¹ HCl, 50% aqueous methanol and 0.2 mol L⁻¹ citric acid (for masking co-extracted Fe³⁺) was selected as the most suitable extraction agent. The efficiency of proposed extraction method was better than 95% with R.S.D. below 6%. A preconcentration method utilizing a “homemade” C18 solid phase extraction (SPE) microcolumns was developed to enhance sensitivity of the mercury species determination using on-column complex formation of mercury-2-mercaptophenol complexes. Methanol was chosen for counter-current elution of the retained mercury complexes achieving a preconcentration factor as much as 1000. The preconcentration method was applied for the speciation analysis of mercury in river water samples. The high-performance liquid chromatography-cold vapour atomic fluorescence spectrometric (HPLC/CV-AFS) method was used for the speciation analysis of mercury. The complete separation of four mercury species was achieved by an isocratic elution of aqueous methanol (65%/35%) on a Zorbax SB-C18 column (4.6 mm × 150 mm, 5 μm) using the same complexation reagent (2-mercaptophenol). The limits of detection were 4.3 μg L⁻¹ for methylmercury (MeHg⁺), 1.4 μg L⁻¹ for ethylmercury (EtHg⁺), 0.8 μg L⁻¹ for inorganic mercury (Hg²⁺), 0.8 μg L⁻¹ for phenylmercury (PhHg⁺).     

Determination of mercury species by the diffusive gradient in thin film technique and liquid chromatography – atomic fluorescence spectrometry after microwave extraction

A diffusive gradient in thin films technique (DGT) was combined with liquid chromatography (LC) and cold vapor atomic fluorescence spectrometry (CV-AFS) for the simultaneous quantification of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, and C₆H₅Hg⁺). After diffusion through an agarose diffusive layer, the mercury species were accumulated in resin gels containing thiol-functionalized ion-exchange resins (Duolite GT73, and Ambersep GT74). A microwave-assisted extraction (MAE) in the presence of 6 M HCl and 5 M HCl (55 °C, 15 min) was used for isolation of mercury species from Ambersep and Duolite resin gels, respectively. The extraction efficiency was higher than 95.0% (RSD 3.5%). The mercury species were separated with a mobile phase containing 6.2% methanol + 0.05% 2-mercaptoethanol + 0.02 M ammonium acetate with a stepwise increase of methanol content up to 80% in the 16th min on a Zorbax C18 reverse phase column. The LODs of DGT–MAE–LC–CV-AFS method were 38 ng L⁻¹ for CH₃Hg⁺, 13 ng L⁻¹ for Hg²⁺, 34 ng L⁻¹ for C₂H₅Hg⁺ and 30 ng L⁻¹ for C₆H₅Hg⁺ for 24 h DGT accumulation at 25 °C.     

Multicapillary gas chromatography coupled to inductively coupled plasma-time-of-flight mass spectrometry for rapid mercury speciation analysis

A simple, rapid and accurate method on the basis of multicapillary gas chromatography (MCGC) combined with inductively coupled plasma-time-of-flight mass spectrometry (ICP-TOFMS) was developed for speciation analysis of methylmercury (MeHg⁺) and inorganic mercury (Hg²⁺). The potential of the ICP-TOFMS for transient multi-isotope detection of very short signals (peak width of 0.4 s at half peak height) was evaluated. Two injection systems (purge-and-trap (PTI) and split (SI) injections) were compared in terms of species separation resolution and transient signal profile. Using purge-and-trap injection, after in situ derivatization of the ionic mercury species with sodium tetraethylborate, a baseline separation of MeHg⁺ and Hg²⁺ was achieved within a chromatographic run of <35 s. To correct for matrix-induced ion signal variation and instrumental drift, propylmercury (PrHg⁺) was used as internal standard. Detection limits of 16 and 257 fg g⁻¹ for MeHg⁺ (as Hg) and Hg²⁺, respectively, were achieved. The analytical precision (R.S.D. (%)) for 10 successive injections of a standard mixture containing 10 pg MeHg⁺ (as Hg) and Hg²⁺ was 1.2% for MeHg⁺ and 4.1% for Hg²⁺. The method was validated by analysis of two biological certified reference materials (CRM): a dogfish muscle (DORM-2) and a freeze-dried tuna fish (CRM 464).     

Online anion exchange column preconcentration and high performance liquid chromatographic separation with inductively coupled plasma mass spectrometry detection for mercury speciation analysis

A hyphenated method for mercury speciation analysis by the coupling of high performance liquid chromatography and inductively coupled plasma mass spectrometry with the online strong anion exchange column (SAX) preconcentration was developed. The Hg analytes (Hg⁺, MeHg, EtHg and Hg²⁺) were absorbed on the SAX column preconditioned with sodium 3-mercapto-1-propanesulfonate, and then rapidly eluted (less than 16 s) by 5 μL 3% (v/v) 2-mercaptoethanol. The enrichment factors of 1025 for Hg⁺, 1084 for MeHg, 1108 for EtHg and 1046 for Hg²⁺ were obtained using 6 mL sample in a 1.5-min enrichment procedure. Rapid separation of the four mercurial compounds was achieved within 5 min on a 50-mm C₁₈ column using 0.5% (v/v) 2-mercaptoethanol as the mobile phase. The detection limits for Hg⁺, MeHg, EtHg and Hg²⁺ were 0.015, 0.010, 0.009 and 0.016 ng L⁻¹, each, and the relative standard deviations of peak height and peak area (5 ng L⁻¹ for each Hg species) were all below 5%. Mercury speciation in three freshwater, two drinking water and two seawater samples were then analyzed by the proposed method. MeHg and Hg²⁺ concentrations down to 0.14 and 0.56 ng L⁻¹ were detected in the drinking waters.     

High-performance liquid chromatographic/ion-trap mass spectrometric speciation of aquatic mercury as its pyrrolidinedithiocarbamate complexes

Mercury-pyrrolidinedithiocarbamate complexes are first time used for speciation of aquatic mercury with high-performance liquid chromatographic/ion trap-mass spectrometric method utilizing atmospheric pressure chemical ionization (APCI). The separation of the four mercury species was achieved in less than 5 min with a linear gradient profile of aqueous methanol from 70 up to 100% (v/v) in 4th min, isocratic elution at 100% up to 5th min and followed by a negative gradient to 70% in 6th min. The best separation was achieved on a reverse phase Zorbax Eclipse XDB C18 column (50 mm × 2.1 mm i.d., 1.8 μm particle size). The on-column limits of detection (injection volume 1 μL) were 370 pg for methylmercury (MeHg⁺), 280 pg for ethylmercury (EtHg⁺), 250 pg for phenylmercury (PhHg⁺) and 90 pg for inorganic mercury (Hg²⁺) when the data were collected in selective ion monitoring (SIM) mode. A method of isolation and preconcentration of the mercury species using a “home-made” C18 solid phase extraction (SPE) microcolumns was developed to enhance sensitivity of the method. The preconcentration factor as much as 2500 was achieved with on-column complex formation of mercury-pyrrolidinedithiocarbamate. Methanol (100%) was chosen for elution of preconcentrated mercury species. The method was applied for the determination of mercury species in river water samples.     

Determination of methylmercury and inorganic mercury by coupling short-column ion chromatographic separation,on-line photocatalyst-assisted vapor generation,and inductively coupled plasma mass spectrometry

We have combined short-column ion chromatographic separation and on-line photocatalyst-assisted vapor generation (VG) techniques with inductively coupled plasma mass spectrometry to develop a simple and sensitive hyphenated method for the determination of aqueous Hg²⁺ and MeHg⁺ species. The separation of Hg²⁺ and MeHg⁺ was accomplished on a cation-exchange guard column using a glutathione (GSH)-containing eluent. To achieve optimal chromatographic separation and signal intensities, we investigated the influence of several of the operating parameters of the chromatographic and photocatalyst-assisted VG systems. Under the optimized conditions of VG process, the shortcomings of conventional SnCl₂-based VG techniques for the vaporization of MeHg⁺ was overcome; comparing to the concentric nebulizer-ICP-MS system, the analytical sensitivity of ICP-MS toward the detection of Hg²⁺ and MeHg⁺ were also improved to 25- and 7-fold, respectively. With the use of our established HPLC–UV/nano-TiO₂–ICP-MS system, the precision for each analyte, based on three replicate injections of 2 ng/mL samples of each species, was better than 15% RSD. This hyphenated method also provided excellent detection limits—0.1 and 0.03 ng/mL for Hg²⁺ and MeHg⁺, respectively. A series of validation experiments—analysis of the NIST 2672a Standard Urine Reference Material and other urine samples—confirmed further that our proposed method could be applied satisfactorily to the determination of inorganic Hg²⁺ and MeHg⁺ species in real samples.     

Method optimization for the determination of four mercury species by micro-liquid chromatography-inductively coupled plasma mass spectrometry coupling in environmental water samples

A method based on the coupling microHPLC-microneb-ICPMS has been developed for Hg(II), MeHg⁺, EtHg⁺ and PhHg⁺ species. Gradient elution using methanol and l-cysteine at pH 3.0 allowed the chromatographic separation of all species in less than 13 min (total analysis time 15 min). The direct coupling of microLC to ICPMS through a Micromist nebulizer permits the analysis of environmental water without sample pretreatment and derivatization steps. Nebulizer type, organic modifier and column length were the main parameters tested. The methanol content and pH of the mobile phase greatly affected the retention time and sensitivity of the method. Key factors to obtain high signal to noise ratio, at concentrations below 1 μg L⁻¹, were found to be the nebulization step and traces of Hg present in the complexing agent. A detailed optimization of carrier and make up gas flow rates have enabled the nebulization of the methanol gradient elution with good mass transport efficiency, low organic solvent loading into the plasma and excellent precision.The performance of the microHPLC-microneb-ICPMS method developed was evaluated on a surface water sample filtered (0.22 μm) and spiked with 0.5 μg L⁻¹ (as Hg) of each species. Precision (R.S.D., n = 6) for all species of Hg varied from 0.5 to 2.1%. Detection limit, defined as three times the standard deviation (n = 6), ranged from 8 ng L⁻¹ for EtHg⁺ to 32 ng L⁻¹ for PhHg⁺ and was noticeably lower than those reported in previous LC-based methods. Accuracy was suitable with recoveries ranging from 85 to 100% when tested at two levels (0.5 and 10 μg L⁻¹) in groundwater samples. Recovery was matrix affected when water samples of high salinity (depurated wastewater and seawater) were used.     

Determination of methylmercury and inorganic mercury in water samples by slurry sampling cold vapor atomic absorption spectrometry in a flow injection system after preconcentration on silica C18 modified

A novel method for preconcentration of methylmercury and inorganic mercury from water samples was developed involving the determination of ng l⁻¹ levels of analytes retained on the silica C₁₈ solid sorbent, previous complexation with ammonium pyrrolidine dithiocarbamate (APDC), by slurry sampling cold vapor atomic absorption spectrometry (SS-CVAAS) in a flow injection (FI) system. Several variables were optimized affecting either the retention of both mercury species, such as APDC concentration, silica C₁₈ amount, agitation times, or their determination, including hydrochloric acid concentration in the suspension medium, peristaltic pump speed and argon flow-rate. A Plackett-Burman saturated factorial design permitted to differentiate the influential parameters on the preconcentration efficiency, which were after optimized by the sequential simplex method. The contact time between mercury containing solution and APDC, required to reach an efficient sorption, was decreased from 26 to 3 min by the use of sonication stirring instead of magnetic stirring. The use of 1 mol dm⁻³ hydrochloric acid suspension medium and 0.75% (m/v) sodium borohydride reducing agent permitted the selective determination of methylmercury. The combination of 5 mol dm⁻³ hydrochloric acid and 10⁻⁴% (m/v) sodium borohydride was used for the selective determination of inorganic mercury. The detection limits achieved for methylmercury and inorganic mercury determination under optimum conditions were 0.96 and 0.25 ng l⁻¹, respectively. The reliability of the proposed method for the determination of both mercury species in waters was checked by the analysis of samples spiked with known concentrations of methylmercury and inorganic mercury; quantitative recoveries were obtained.     

Adsorption of mercury species on river sediments — effects of selected abiotic parameters

Abiotic parameters (pH, temperature, current velocity, mercury species concentration, and sediment and aqueous media composition) influence mercury species (MeHg⁺, EtHg⁺, PhHg⁺ and inorganic Hg²⁺) adsorption on river sediments. The highest amount of adsorbed MeHg⁺ and EtHg⁺ (82–93% and 85–91% for static and agitated system, respectively) occurred at pH 3–4. For PhHg⁺ the maximum adsorption (90% and 95% for static and agitated systems) was located over the broad 3–10 pH range, while for Hg²⁺ (94% and 97% for static and agitated systems) it was at pH ∼ 3. Temperature (4.5–60°C) influenced the adsorption rate but not the quantity. Both rate and quantity increased in the order: static < agitated ≤ stirred systems. The aqueous medium composition affected both rate and quantity. Sulfate caused the largest adsorption decrease for organomercury species (15–25% decrease); sulfide reduced Hg²⁺ adsorption about 67%. Cations at pH 5.2 reduced either the adsorption rate (Ca²⁺, Al³⁺) or the total adsorption (Zn²⁺, Fe³⁺). Positive correlations were found between sediment C, N, S content as well as cation exchange capacity (CEC) with mercury adsorption (R = 0.45–0.66, 0.56–0.89, 0.45–0.61 and 0.55–0.73, respectively) while negative correlations were observed with Fe and Al (R = −0.63 to −0.90 and −0.65 to −0.86, respectively).     

Development of the diffusive gradient in thin films technique for the measurement of labile mercury species in waters

The diffusive gradients in thin films (DGT) technique, utilizing resin gel with ion-exchange resin Duolite GT73 and new ion-exchange resin Ambersep GT74, was investigated for the accumulation of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, C₆H₅Hg⁺). The diffusion coefficients of mercury species in agarose gel calculated on the basis of Fick’s Law were mercury species-specific. The diffusion coefficients of Hg²⁺ and CH₃Hg⁺ at 25 °C (9.07 ± 0.23 × 10⁻⁶ cm² s⁻¹ and 9.06 ± 0.30 × 10⁻⁶ cm² s⁻¹, respectively) were very similar, but the diffusion coefficients of C₂H₅Hg⁺ (6.87 ± 0.23 × 10⁻⁶ cm² s⁻¹) and C₆H₅Hg⁺ (3.86 ± 0.19 × 10⁻⁶ cm² s⁻¹) were significantly lower. Influence of experimental conditions (pH, selected cations, chlorides and humic substance) on mercury species accumulation by DGT was studied. The DGT technique was applied to river water spiked with mercury species.     

Preconcentration and speciation of inorganic and methyl mercury in waters using polyaniline and gold trap-CVAAS

Applicability of polyaniline (PANI) has been investigated for the preconcentration and speciation of inorganic mercury (Hg²⁺) and methyl mercury (CH₃Hg⁺) in various waters (ground, lake and sea waters). Preliminary experiments (batch) with powdered PANI for the quantitative removal of both Hg²⁺ and CH₃Hg⁺ showed that the retention of Hg²⁺ was almost independent of pH while a pH dependent trend from pH 1 to 12 was seen for CH₃Hg⁺ with maximum retention at pH > 5. Time dependence batch studies showed that a contact time of 10 min was sufficient to reach equilibrium. The K_d values were found to be ∼8 × 10⁴ and ∼7 × 10³ for Hg²⁺ and CH₃Hg⁺, respectively.Subsequently column experiments were carried out with PANI and the separation of the species was carried out by selective and sequential elution with 0.3% HCl for CH₃Hg⁺ and 0.3% HCl-0.02% thiourea for Hg²⁺. This was then followed by further pre-concentration of mercury on a gold trap and its determination by CVAAS. The uptake efficiency studies showed that the PANI column was able to accumulate up to 100 mg Hg²⁺/g and 2.5 mg CH₃Hg⁺/g. This method allows both preconcentration and speciation of mercury with preconcentration factors around 120 and 60 for Hg²⁺ and CH₃Hg⁺, respectively. The interfering effects of various foreign substances on the retention of mercury were investigated.     

Metal–organic frameworks of zeolitic imidazolate framework-7 and zeolitic imidazolate framework-60 for fast mercury and methylmercury speciation analysis

A fluorescence sensing platform based on metal–organic frameworks (MOFs) nanoparticles (NPs) of both zeolitic imidazolate framework-7 (ZIF-7) and zeolitic imidazolate framework-60 (ZIF-60) was developed for speciation analysis of inorganic Hg [Hg(II)] and methylmercury (MeHg⁺). Microwave-ultrasound assisted synthesis was employed for the preparation of ZIF-7 and ZIF-60 NPs, with short reaction time, easy procedure, and small particle size obtained. Based on strict cavity confinement of the ZIF-7 and ZIF-60 structures, the proposed method exhibited excellent selectivity for both Hg(II) and MeHg⁺, even in the presence of the other Hg species or various cations or anions with the concentration of 50 times high. Effect of pH and ionic strength on sensing behaviour of the ZIF MOF was studied as well. The calculated detection limit is 3 ng mL⁻¹ and 6 ng mL⁻¹ for Hg(II) and MeHg⁺, respectively. Furthermore, the application of the developed method to the analysis of local drinking water was demonstrated to be feasible, and the obtained recovery was 102% and 96.2% for Hg(II) and MeHg⁺, respectively.