Synthesis and curing of novel LC twin epoxy monomers for liquid crystal thermosets

This article describes the synthesis and characterization of new liquid crystalline thermosets having a twin structure. Nematic epoxy-terminated monomers based on a phenyl benzoate twin mesogen connected by an alkylene spacer were synthesized for these studies. In addition, an epoxy-terminated monomer based on a 1,4-bis(benzoyloxy)phenylene mesogen was synthesized to determine the effect of the position of the mesogen on the final network structure. The diepoxy monomer made with phenyl benzoate twin mesogens connected with an alkylene spacer formed a smectic-like network when cured with diamines. This smectic organization appeared even though the diepoxy monomer itself showed only a nematic mesophase over a narrow temperature range. The presence of crosslinks at both ends of the mesogens helped to retain a uniform spacing between crosslinking sites during the curing reaction, and aided formation of the smectic layer arrangement. The epoxy monomer possessing a 1,4-bis(benzoyloxy)phenylene mesogen and two epoxidized alkylene end groups on both sides of the mesogen formed a stable nematic mesophase. However, in contrast to the twin epoxies, the latter epoxy when reacted with diamines tended to produce a nematic-like network which was retained as the crosslinking reaction proceeded. © 1996 John Wiley & Sons, Inc.     

Low temperature polymerization of novel,monotropic liquid crystalline benzoxazines

Cationic ring opening polymerization at a lower temperature range/faster polymerization than ordinary benzoxazine resins has been achieved without added initiators or catalysts via liquid crystalline (LC) benzoxazine resins. Faster polymerization is observed even above the liquid crystal forming temperature. The FTIR spectra show that opening of the oxazine ring occurs even at 110 °C generating phenolic groups that auto‐catalyzed the cationic polymerization of the monomer increasing the rate of polymerization. The newly formed H‐bonds inhibit the formation of LC phases after polymerization. Some of the monomers show nematic LC transitions upon cooling. None of them showed LC transitions during the heating cycle, exhibiting monotropic LC phases. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5871–5881, 2009     

Liquid crystalline epoxy thermosets based on dihydroxymethylstilbene: Synthesis and characterization

This article describes the synthesis and characterization of a new series of liquid crystalline thermosets. Nematic epoxy-terminated oligoethers based on dihydroxy-α-methylstilbene were synthesized for this study. These prepolymers were crosslinked within the nematic mesophase using methylenedianiline. Depending upon the molecular weight and polydispersity of the oligoether, the crosslinking reaction resulted in networks with either a smectic or nematic molecular organization in contrast to the simple nematic phase of the oligoether. The formation of a smectic-like structure on curing was found to be related to the breadth of the prepolymer molecular weight. In those networks with a low crosslink density a clearing transition could be observed, whereas in the more highly crosslinked networks the molecular organization was frozen in until decomposition. The glass transition temperature of these LC networks rose as the crosslink density was increased, ranging from 35 to 152°C. In agreement with theory, the clearing transition of the networks was found to be dependent on the phase state during curing © 1992 John Wiley & Sons, Inc.     

SYNTHESIS OF A GROUP OF MESOGEN JACKETED LIQUID CRYSTAL POLYMERS

A group of the mesogen jacketed liquid crystal polymers based on the monomers 2,5-bis (4-substituted benzoyl)oxystyrenes are synthesized. The substituents include alkoxy, alkyl, and cyano groups. The synthesis and the primary characterization of the liquid crystal phase of the monomers and the polymers are described. While some of the monomers give smectic textures the polymers are found to be nematic above their melting or glass transition temperatures. Interestingly the unsubstituted monomer and its polymer poly 2,5-di( benzoyloxy ) styrene are also liquid crystalline. The single crystal structure of one of the monomers is also discussed.     

Polymerization and viscoelastic behavior of networks from a dual‐curing,liquid crystalline monomer

The network formation and viscoelastic behavior of a liquid crystalline monomer, whose structure includes both acrylate and acetylene reactive groups, have been studied. By combining both photo and thermal polymerization, the networks can be formed in two separate steps, with the initial photopolymerization dominated by acrylate crosslinking and subsequent thermal polymerization dominated by acetylene crosslinking. In addition, the monomer exhibits a liquid crystalline phase. Photopolymerization while in the liquid crystal phase locks in the molecular ordering. Dynamic mechanical analysis shows that networks formed from the liquid crystalline phase have lower crosslink densities and narrower distributions of molecular weights between crosslinks when compared to networks formed from the isotropic phase (and at higher polymerization temperatures). After thermal postcure at 250°C, the networks formed from the isotropic monomer have a 23% higher dynamic mechanical storage modulus (in the glassy state) than the networks formed from the liquid crystalline monomer. The thermally postcured networks have unusually high glass‐transition temperatures, which exceed 300°C. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1183–1190, 1999     

Liquid crystalline thermosets based on anisotropic phases of cellulose nanocrystals

A new class of liquid crystalline thermosets (LCTs) was successfully produced containing lyotropic cellulose nanocrystals (CNCs) as the primary mesogenic component (up to 72 wt%) by the addition of non-mesogenic epoxy monomers. Cellulose-based LCTs were produced by totally aqueous processing methods and ultimately cured at elevated temperatures to produce ordered networks of ‘frozen’ liquid crystalline (LC) phases. Various degrees of birefringence were obtained via self-assembly of CNCs into oriented phases as observed by polarized optical microscopy and transmission electron microscopy. X-ray diffraction measurements highlighted the effects of texture of CNCs within LCT films compared to lyophilized CNCs. Cellulose-based LCT films uniquely exhibited thermo-mechanical properties of both traditional LCTs and LC elastomers, such as high elastic modulus (~1 GPa) under ambient conditions and low glass transition temperature (~?25 °C), respectively. The development of LCTs based on CNCs and aqueous processing methods provides a renewable pathway for designing high performance composites with ordered network structures and unique optical properties.     

The mechanical and magnetic alignment of liquid crystalline epoxy thermosets

The processing of a new series of liquid crystalline (LC) epoxy networks was evaluated. Above the glass transition temperature, the low crosslink density networks could be mechanically aligned. The mechanically oriented networks readily lost orientation upon heating. Highly anisotropic liquid crystalline (LC) epoxy networks were also prepared by aligning the mesophase of the prepolymer during the curing process under the influence of a magnetic field. Orientation parameters (f) of 0.13 to 0.57 were achieved by these processes as determined by x-ray diffraction analysis. The ability of the magnetically aligned networks to retain their orientation above the glass transition temperature was determined by time-resolved x-ray diffraction. The stability of the alignment of these networks was found to depend on crosslink density. The effect of the anisotropy of these networks was investigated by measuring the coefficient of thermal expansion (CTE). In the aligned networks, there was a substantial reduction in CTE parallel to the direction of the applied field compared to the randomly oriented networks. © 1992 John Wiley & Sons, Inc.     

Evolution of structure and properties of a liquid crystalline epoxy during curing

The evolution of structure, and thermal and dynamic mechanical properties of a liquid crystalline epoxy during curing has been studied with differential scanning calorimetry (DSC), polarized optical microscopy, x-ray scattering, and dynamic mechanical analysis. The liquid crystalline epoxy was the diglycidyl ether of 4,4′-dihydroxy-α-methylstilbene (DGEDHMS). Two curing agents were used in this study: a di-functional amine, the aniline adduct of DGEDHMS, and a tetra-functional sulfonamido amine, sulfanilamide. The effects of curing agent, cure time, and cure temperature have been investigated. Isothermal curing of the liquid crystalline epoxy with the di-functional amine and the tetra-functional sulfonamido amine causes an increase in the mesophase stability of the liquid crystalline epoxy resin. The curing also leads to various liquid crystalline textures, depending on the curing agent and cure temperature. These textures coarsen during the isothermal curing. Moreover, curing with both curing agents results in a layered structure with mesogenic units aligned perpendicular to the layer surfaces. The layer thickness decreases with cure temperature for the systems cured with the tetra-functional curing agent. The glass transition temperature of the cured networks rises with increasing cure temperature due to the increased crosslink density. The shear modulus of the cured networks shows a strong temperature dependence. However, it does not change appreciably with cure temperature. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2363–2378, 1997     

Synthesis and photochemistry of side-chain liquid crystal polymers based on cinnamate esters

The syntheses of three methacrylate monomers with cinnamate ester side-chains and of a further monomer with a corresponding cinnamide side-chain are described. Two of the monomers, with isomeric structures, were thermotropic liquid crystals. Although the clearing points were very similar the crystal melting points differed by 8°C. One compound also exhibited a monotropic smectic phase, behavior not shown by its isomer. The other two monomers were not liquid crystalline. The monomers were polymerized by free radical polymerization, both as homopolymers and as copolymers with methyl methacrylate. In the case of one of the mesogenic ester monomers, copolymers with a cyanophenyl benzoate monomer were also prepared. Three of the four monomers formed thermotropic liquid crystalline homopolymers and the copolymers with the benzoate monomer were also liquid crystalline. The monomers were considered as photoactive components of polymeric liquid crystals. As a preliminary investigation of their photochemistry, copolymers with methyl methacrylate were prepared and irradiated in solution with a broad-band source. Under these conditions two of the materials show a facile photo-Fries rearrangement of the aryl cinnamate ester group. © 1992 John Wiley & Sons, Inc.     

Optically-active comb-branch liquid crystalline polymers having the chiral center in the flexible spacer unit. III. Copolymers of (S)-2-(4′-cyano-4-biphenylyloxy)-1-methylethoxy ethyl methacrylate and di[6-(4-methoxy-4′-oxybiphenyl) hexyl]-2-methylene butane-1,4-dioate

A new series of copolymers with optically-active liquid crystalline side chain units has been synthesized from the comonomers (S)-2-[2-(4′-cyano-4-biphenylyloxy-1-methylethoxy]ethyl methacrylate ( 1 ) and di[6-(4-methoxy-4′-oxybiphenyl)hexyl]-2-methylene butane-1,4-dioate ( 4 ). Chiral nematic phases were exhibited by two members of the series, rich in monomer 1 , while a smectic phase was exhibited in copolymers rich in 4 . While it was thought possible that ordered chiral liquid crystalline phases may be induced by copolymerizing chiral mesogenic monomers with mesogenic derivatives of itaconic acid where the high side chain density encourages greater ordering in the system, no evidence of smectic C^* phases could be found in the present systems. © 1993 John Wiley & Sons, Inc.     

New liquid crystal polyethers and polyesters based on diphenylbutadiene mesogens

New liquid-crystalline (LC) polymers and small molecules have been synthesized based on the 1,4-diphenylbutadiene mesogen, a chromophore with χ⁽³⁾ nonlinear optical properties. Polyethers were formed by phase-transfer reaction, and polyesters were prepared by Schotten-Bauman polymerization from these 4,4'-bisphenolic mesogenic structures. Liquid crystallinity was examined using differential scanning calorimetry (DSC) and optical microscopy. Most of the model compounds were found to be nematic. All mesomorphic polymers were nematic and displayed LC ranges of up to 50°C as well as a wide diversity of melting points. The melting points varied with the flexible (methylene) spacer length and were strongly dependent upon the presence of substituents in the mesogenic core. Crosslinking and cis-trans isomerization were observed under the influence of heat and ultraviolet radiation. © 1992 John Wiley & Sons, Inc.     

High-temperature stability of a novel phenylethynyl liquid-crystalline thermoset

We report the synthesis of a new high-temperature liquid-crystalline thermoset based on the phenylethynyl functional group. The monomer was a nematic thermotropic liquid crystal with a melting temperature of 268 °C. The extrapolated onset of the cure exotherm occurred at 313 °C. The cured thermoset retained the nematic liquid-crystalline order of the parent monomer. The monomer and crosslinked resin were characterized by differential scanning calorimetry, optical microscopy, and thermogravimetric analysis. The thermal stability of the crosslinked resin was determined in both air and nitrogen atmospheres at various heating rates. The onset of weight loss in air and nitrogen atmospheres was determined to be 397 and 422 °C, respectively, for a heating rate of 10 °C/min. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4184–4190, 1999     

Synthesis and characterization of liquid crystalline epoxy and co-polymerisation with a non-mesomorphic epoxy resin

A novel liquid crystalline epoxy resin based on the imine group was synthesised and structurally characterised by infrared (IR) and nuclear magnetic resonance (NMR) spectroscopy. The mesogenic behaviour of the monomer was measured by differential scanning calorimetry (DSC) and polarised optical microscopy (POM), and presented various textures in the extensive temperature range. Methyl nadic anhydride (MNA) was employed to cure the liquid crystalline epoxy resin and the curing process was investigated using POM and wide-angle X-ray diffraction (WAXD). Information about distribution of liquid crystalline epoxy resin in the blending system resulted from the FT-IR Imaging System, indicating that molecules of liquid crystalline epoxy resin can agglomerate to form anisotropic domains. The improvement in mechanical properties of diglycidyl ether of biphenol A (DGEBA) modified with liquid crystalline epoxy was achieved. Scanning electronic microscopy (SEM) showed that an extremely rough and highly deformed fracture surface can be obtained. DGEBA modified with liquid crystalline epoxy resin was characterised by dynamic mechanical analysis (DMA) for its thermal properties. The results indicate that the presence of the liquid crystal phase influences glass transition temperature (Tg).     

Liquid crystal polymers. 14. Synthesis and properties of thermotropic poly(1,4-alkylphenylene terephthalates)

A series of terephthalate polyesters was prepared from substituted hydroquinone monomers that contained a single cyclic or branched alkyl group. All the polymers were crystalline with melting points well below 400°C that decreased as the size of the cycloalkyl substituent increased. Most of the polymers had clearing temperatures below 400°C and all formed nematic melts. Copolyesters that contained equimolar amounts of two different substituted hydroquinone monomers, which were crystalline and had broad temperature ranges for nematic phase formation, were also prepared.     

Synthesis and properties of mesogen‐jacketed liquid crystalline polymers containing biphenyl mesogen with asymmetric substitutions

This work focuses on the design, synthesis, and characterization of a series of mesogen‐jacketed liquid crystalline polymers (MJLCPs), poly(alkyl 4′‐(octyloxy)‐2‐vinylbiphenyl‐4‐carboxylate) (pVBP(m,8), m = 1, 2, 4, 6, 8, 10, 12). For the first time, we realized asymmetric substitutions in the mesogens of MJLCPs. The polymers obtained by conventional free radical polymerization were investigated in detail by a combination of various techniques, such as differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized light microscopy. Our results showed that all the polymers were thermally stable, and their glass transition temperatures decreased when m increased. The liquid crystalline (LC) phases that developed at high temperatures and disappeared at low temperatures were strongly dependent on the difference in lengths of alkyl groups on the 4 and 4′ substitution positions of the side‐chain biphenyl. While polymer pVBP(1,8) was not liquid crystalline, columnar liquid crystalline phases were observed for all other pVBP(m,8) (m = 2, 4, 6, 8, 10, 12) polymers. Polymer pVBP(8,8) showed a tetragonal columnar nematic liquid crystalline phase, and the other LC polymers exhibited columnar nematic phases. In additions, the smaller the difference in the lengths of the terminal alkyls, the easier the development of the liquid crystalline phase. Birefringence measurements showed that solution‐cast polymer films exhibited moderately high positive birefringence values, indicating potential applications as optical compensation films for liquid crystal displays. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

4,4'-二(4-烯丙氧基苯甲酸)联苯酯的合成及其液晶性能

以3-溴丙烯、4-羟基苯甲酸和4,4'-二羟基联苯为主要原料,经Williamson醚化、羧酸酰化和酯化反应合成了一种新的液晶单体--4,4'-二(4-烯丙氧基苯甲酸)联苯酯(1),用~1H NMR,~(13)C NMR,FT-IR,DSC,TGA和POM对其分子结构和液晶性能进行了表征.结果表明1呈现向列相,具有较高的熔点、液晶清亮点和较宽的液晶相温度范围.     

A Novel Pentaerythritol-based Carbosilane Liquid Crystalline Dendrimer Containing 12 Nitroazobenzene Groups on the Periphery

A novel liquid crystalline dendrimer with peripheral mesogenic units was successfully prepared. Azo-reaction and Williamson synthesis were employed in the preparation of the mesogenic unit 4-[4-(6-hydroxyhexyloxy)-phenylazo]nitrobenzene (M-NO2). A terminal Si-Cl functional carbosilane dendrimer based on pentaerythritol was used as dendritic scaffold and subsequently functionalized with the aforementioned groups. Investigation of the liquid crystalline properties of the mesogen-functionalized dendrimer PCSi-IG-NO2 by polarizing optical microscopy, DSC, and X-ray diffraction showed that it exhibits smectic E (SE) phase, different from the corresponding mesogenic unit, which shows nematic phase. Furthermore, the temperatures of both the melting point and the clearing point of the mesogen-functionalized dendrimer decrease, and the temperature region of the SE phase is wider than that of the nematic phase.     

New liquid‐crystalline poly(ester amide)s: The role of nitro groups in the phase behavior

New hydrogen‐bonded liquid‐crystalline poly(ester amide)s (PEA)s were obtained from 1,4‐terephthaloyl[bis‐(3‐nitro‐N‐anthranilic acid)] (5) or 1,4‐terephthaloyl[bis‐(N‐anthranilic acid)] (6), with or without nitro groups, respectively, through the separate condensation of each with hydroquinone or dihydroxynaphthalene. The dicarboxylic monomers were synthesized from 2‐aminobenzoic acid. The phase behavior of the monomers and polymers were studied with differential scanning calorimetry, polarized light microscopy, and wide‐angle X‐ray diffraction methods. Monomer 5, containing nitro groups, exhibited a smectic liquid‐crystalline phase, whereas the texture of monomer 6 without nitro groups appeared to be nematic. The PEAs containing nitro groups exhibited polymorphism (smectic and nematic), whereas those without nitro groups exhibited only one phase transition (a nematic threaded texture). The changes occurring in the phase behavior of the polymers were explained by the introduction of nitro groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1289–1298, 2004     

Synthesis and characterization of fluorine-containing cholesteric liquid crystalline polysiloxanes bearing trifluoromethyl-substituted mesogens

A series of side-chain liquid crystal (LC) polysiloxanes were synthesised with Poly(methylhydrogeno)siloxane, 4?-(undec-10-enoyloxy) biphenyl – 4 – yl 4- (trifluoromethyl) benzoate (M_th) and a chiral nematic (N*) LC monomer 1-allyl 10-(cholesteryl)-decanedioate (M_ch). The chemical structures and LC properties of the monomers and polymers were characterised by FTIR, ¹H-NMR, differential scanning calorimetry, thermogravimetric analysis, POM and X-ray diffractometer. M_ch is monotropic N* LC. The homopolymer derived from monomer M_ch is enantiotropic N* LC. Monomer M_th is a smectic A liquid crystal. The copolymers derived from M_ch and M_th are N* LCs. The temperatures at which 5% weight loss occurred are greater than 300°C for all the fluoro-containing polymers, and the residue weights of the samples at 600°C increased slightly as the content of trifluoromethyl mesogens increased in the polymers. The glass transition temperatures of the polymers increased as trifluoromethyl mesogens increased, too. The N*–I phase transition temperatures show a negative deviate from ideal or linear behaviour. The values of the enthalpy changes for the cholesteryl containing polymers are rather low and this is attributed to the biaxiality of cholesteryl moiety which tends to reduce the change in the orientational order at the N*–I transition. Compared to the monomers, the polymers show wider mesophase region.     

Side chain liquid crystalline diethanolamine‐based polyesters with methoxy and/or nitroazobenzene mesogenic moieties

Side‐chain polyesters based on diethanolamine and 5‐hydroxyisophthalic acid with mesogenic methoxyazobenzene and nitroazobenzene groups were synthesized and their liquid crystalline properties were examined.

Four different types of polyesters were prepared by using various combinations of monomers differing in the mesogen group and the length of the spacer. The thermal and structural properties depend on the type of polyester as well as on the side chain length. The glass transition and isotropization temperatures increase when the methoxyazobenzene group is bound to a diol and decrease when it is bound to an isophthalic acid. Most of the polyesters are thermotropic liquid crystals and form a nematic phase on heating. Some polyesters exhibit shear induced isotropisation to nematic transition up to 25°C above the isotropization temperature.