Proton-conducting solid oxide fuel cell (SOFC) with Y-doped BaZrO3 electrolyte

Y-doped BaZrO₃ (BZY) electrolyte films are successfully fabricated by utilizing the driving force from the anode substrate, aiming to circumvent the refractory nature of BZY materials. The BZY electrolyte film on the high shrinkage anode becomes dense after sintering even though no sintering aid is added, while the BZY electrolyte remains porous on the conventional anode substrate after the same treatment. The resulting BZY electrolyte shows a high conductivity of 4.5 × 10^− 3 S cm^− 1 at 600 °C, which is 2 to 20 times higher than that for most of BZY electrolyte films in previous reports. In addition, the fuel cell with this BZY electrolyte generates a high power output of 267 mW cm^− 2 at 600 °C. These results suggest the strategy presented in this study provides a promising way to prepare BZY electrolyte films for fuel cell applications.     

Development of micro-tubular SOFCs with an improved performance via nano-Ag impregnation for intermediate temperature operation

Micro-tubular solid-oxide fuel cell consisting of a 10-μm thick (ZrO₂)_0.89(Sc₂O₃)_0.1(CeO₂)_0.01 (ScSZ) electrolyte on a support NiO/(ScSZ) anode (1.8 mm diameter, 200 μm wall thickness) with a Ce_0.8Gd_0.2O_1.9 (GDC) buffer-layer and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF)/GDC functional cathode has been developed for intermediate temperature operation. The functional cathode was in situ formed by impregnating the well-dispersed nano-Ag particles into the porous LSCF/GDC layer using a citrate method. The cells yielded maximum power densities of 1.06 W cm⁻² (1.43 A cm⁻², 0.74 V), 0.98 W cm⁻² (1.78 A cm⁻², 0.55 V) and 0.49 W cm⁻² (1.44 A cm⁻², 0.34 V), at 650, 600 and 550 °C, respectively.     

High performance cathode-supported SOFC with perovskite anode operating in weakly humidified hydrogen and methane

A high performance cathode-supported solid oxide fuel cell (SOFC), suitable for operating in weakly humidified hydrogen and methane, has been developed. The SOFC is essentially made up by a YSZ/LSM composite supporting cathode, a thin YSZ film electrolyte, and a GDC-impregnated La_0.75Sr_0.25Cr_0.5Mn_0.5O₃ (LSCM) anode. A gas tight thin YSZ film (∼27 μm) was formed during the co-sintering of cathode/electrolyte bi-layer at 1200 °C. The cathode-supported SOFC developed in this study showed encouraging performance with maximum power density of 0.182, 0.419, 0.628 and 0.818 W cm⁻² in air/3% H₂O–97% H₂ (and 0.06, 0.158, 0.221 and 0.352 W cm⁻² in air/3% H₂O–97% CH₄) at 750, 800, 850 and 900 °C, respectively. Such performance is close to that of the cathode-supported cell (0.42 W cm⁻² vs. 0.455 W cm⁻² in humidified H₂ at 800 °C) developed by Yamahara et al. [Solid State Ionics 176 (2005) 451–456] with a Co-infiltrated supporting LSM-YSZ cathode, a (Sc₂O₃)_0.1(Y₂O₃)_0.01(ZrO₂)_0.89 (SYSZ) electrolyte of 15 μm in thickness and a SYSZ/Ni anode, indicating that the performance of the GDC-impregnated LSCM anode is comparable to that made of Ni cermet while stable in weakly humidified methane fuel.     

Li2SO4-polyacrylamide polymer electrolytes for 2.0 V solid symmetric supercapacitors

A neutral polymer electrolyte comprised of lithium sulfate (Li₂SO₄) and polyacrylamide (PAM) was developed. The Li₂SO₄-PAM electrolyte film shows an ionic conductivity up to 10 mS cm^− 1 in 45%RH conditions. Solid double layer capacitors were demonstrated using CNT-graphite electrodes and Li₂SO₄-PAM solid electrolytes. The voltage window of the solid cell was about 2.0 V, identical to that of a Li₂SO₄ liquid cell used as baseline. The demonstrated voltage window is significantly larger than that reported for proton- or hydroxyl-conducting electrolytes, suggesting that the Li₂SO₄-PAM electrolyte is a promising system for high energy density supercapacitors. The solid device also demonstrated excellent rate capability (up to 5 V s^− 1) and good cycle life (beyond 10,000 charge/discharge cycles).     

Near-infrared spectroscopy as an effective tool for monitoring the conformation of alkylammonium surfactants in montmorillonite interlayers

Application of near-infrared (NIR) spectroscopy to probing the arrangement of trimethylalkylammonium cations in montmorillonite interlayers has been demonstrated. Detailed analysis of the mid-IR (MIR) and NIR spectra of montmorillonite from Jelšový Potok (JP, Slovakia) saturated with surfactants with varying alkyl chain length (even numbers of carbon atoms from C6 to C18) was performed to show the advantages of the NIR region in characterizing surfactant conformations. The position of the ν_as(CH₂), (∼2930–2920 cm⁻¹), ν_s(CH₂) (∼2860–2850 cm⁻¹), 2ν_as(CH₂) (∼5810–5785 cm⁻¹), (ν + δ)_as(CH₂) (∼4340–4330 cm⁻¹) and (ν + δ)_s(CH₂) (∼4270–4250 cm⁻¹) signals was used as an indicator of the gauche/trans conformer ratio. For all bands, a shift toward lower wavenumber on increasing the alkyl chain length from 6 to 18 carbons suggests a transition from disordered liquid-like to more ordered solid-like structures of the surfactants. The magnitude of the shift was significantly higher for 2ν_as(CH₂) (28 cm⁻¹) than for ν_as(CH₂) (8 cm⁻¹) or ν_s(CH₂) (10 cm⁻¹), showing the NIR region to be a useful tool for examining this issue. Comparison of the IR spectra of crystalline alkylammonium salts and the corresponding organo-montmorillonites demonstrated a confining effect of montmorillonite layers on surfactant ordering. For each alkyl chain length the CH₂ bands of the organo-montmorillonites appeared at higher wavenumbers than for the unconfined surfactant, thus indicating a higher disorder of the alkyl chains. The wavenumber difference between corresponding samples was always higher in the NIR than in the MIR region. All these findings show NIR spectroscopy to be useful for conformational studies.     

Potentiostatically deposited nanostructured α-Co(OH)2: A high performance electrode material for redox-capacitors

A high specific capacitance was obtained for α-Co(OH)₂ potentiostatically deposited onto a stainless-steel electrode in 0.1 M Co(NO₃)₂ electrolyte at −1.0 V vs. Ag/AgCl. The structure and surface morphology of the obtained α-Co(OH)₂ were studied by using X-ray diffraction analysis and scanning electron microscopy. A network of nanolayered α-Co(OH)₂ sheets was obtained; the average thickness of individual α-Co(OH)₂ sheets was 10 nm, and the thickness of the deposit was several micrometers. The capacitive characteristics of the α-Co(OH)₂ electrodes were investigated by means of cyclic voltammetry and constant current charge–discharge cycling in 1 M KOH electrolyte. A specific capacitance of 860 F g⁻¹ was obtained for a 0.8 mg cm⁻² α-Co(OH)₂ deposit. The specific capacitance did not decrease significantly for the active mass loading range of 0.1–0.8 mg cm⁻² due its layered structure, which allowed easy penetration of electrolyte and effective utilization of electrode material even at a higher mass. This opens up the possibility of using such materials in supercapacitor applications.     

A direct borohydride–peroxide fuel cell using a Pd/Ir alloy coated microfibrous carbon cathode

A direct borohydride fuel cell with a Pd/Ir catalysed microfibrous carbon cathode and a gold-catalysed microporous carbon cloth anode is reported. The fuel and oxidant were NaBH₄ and H₂O₂, at concentrations within the range of 0.1–2.0 mol dm⁻³ and 0.05–0.45 mol dm⁻³, respectively. Different combinations of these reactants were examined at 10, 25 and 42 °C. At constant current density between 0 and 113 mA cm⁻², the Pd/Ir coated microfibrous carbon electrode proved more active for the reduction of peroxide ion than a platinised-carbon one. The maximum power density achieved was 78 mW cm⁻² at a current density of 71 mA cm⁻² and a cell voltage of 1.09 V.     

Fabrication and supercapacitive performance of long anodic TiO2 nanotube arrays using constant current anodization

A galvanostatic anodization is used to prepare long TiO₂ nanotube arrays (TNTAs). TNTAs of over 100 μm in length, with similar nanotube size and structural regularity to the classic TNTAs made from potentiostatic mode, are achieved at 10 mA cm^− 2. After a post-anodization in a H₃PO₄-based electrolyte, the TNTAs with long nanotubes exhibit good adhesion to Ti substrate. The as-prepared long TNTAs yield a larger areal capacitance of 128.4 mF cm^− 2. Further, the long TNTAs possess a higher surface area, making them suitable as support templates for other active materials.     

A strategy of tailoring stable electrolyte material for high performance proton-conducting solid oxide fuel cells (SOFCs)

A facile strategy was proposed to synthesize Nb-containing BaCeO₃-based material, which is a potential electrolyte for proton-conducting solid oxide fuel cells (SOFCs), via a wet chemical route while the conventional synthesis of Nb-containing oxides relied on the solid state reaction method due to the unavailability of suitable Nb-precursors such as Nb-nitrates resulting in a less desirable fuel cell performance when used as an electrolyte. The BaCe_0.7Nb_0.1Y_0.2O_3 − δ (BCNY) electrolyte material in this study persisted a good chemical stability against CO₂ and exhibited good performance in the fuel cell application. The fuel cell with BCNY electrolyte film showed a high performance of 533 mW cm^− 2 at 700 °C. This cell performance based on BCNY electrolyte was superior to that of many stable modified BaCeO₃-based proton-conducting SOFCs where the electrolytes were tailored by other strategies. This result indicated that the strategy presented in this study could be an effective way to prepare a stable electrolyte for high performance proton-conducting SOFCs, which could advance the development of proton-conducting SOFCs.     

All-solid-state micro lithium-ion batteries fabricated by using dry polymer electrolyte with micro-phase separation structure

Micro-batteries were fabricated by using BAB block copolymer as dry polymer electrolyte, which consisted of polyethylene oxide and polystyrene and had relatively high ionic conductivity at room temperature. The micro-batteries were fabricated by a sol–gel method combined with micro-injection system. Two types of micro-battery were fabricated. One consists of a single cell and another of 3-cells connected in series. LiMn₂O₄ and Li_4/3Ti_5/3O₄ were used as active materials in positive and negative electrode, respectively. The micro-array batteries were operated at room temperature without any plasticizer in the polymer electrolyte. The operation voltages were 2.45 V and 7.40 V for a single cell and 3-cell array, respectively. The discharge capacities estimated from cyclic voltammetry measurements were 245 nA h for a single cell and 12.1 nA h for a 3-cell array, which corresponded to the energy densities of 8.48 μW h cm⁻² and 4.54 μW h cm⁻², respectively.     

Electrochemical properties of LaCePr-oxide/K2WO4 composite electrolyte for low-temperature SOFCs

In this study, we introduced tungstate into solid oxide fuel cells (SOFCs) for the first time by using a La/Pr-doped CeO₂ (LCP)/K₂WO₄ composite as the electrolyte, which exhibited remarkably enhanced grain boundary conduction compared to that of single-phase LCP. The composition dependence of the electrical conductivity was investigated. As a result, the composite with 10 wt% K₂WO₄ was proven to be the optimum ratio, revealing a significantly higher ionic conductivity than LCP, along with a negligible electronic conductivity. The fuel cell using the LCP/K₂WO₄ electrolyte displayed an encouraging performance of 500 mW cm^− 2 at 550 °C. These findings indicate that the LCP/K₂WO₄ composite is a promising electrolyte for low-temperature SOFCs.     

Molybdenum electrodes for hydrogen production by water electrolysis using ionic liquid electrolytes

The hydrogen production by water electrolysis was tested with different electrocatalysts (molybdenum, nickel, iron alloys containing chromium, manganese and nickel) using aqueous solutions of ionic liquid (IL) like 1-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF₄). The hydrogen evolution reaction (HER) was performed at room temperature in a potential of −1.7 V (PtQRE). A Hoffman cell apparatus was used to water electrolysis with current density values, j, between 14.6 mA cm⁻² (for Ni electrode) and 77.5 mA cm⁻² (for Mo electrode). The system efficiency was very high for all electrocatalysts tested, between 97.0% and 99.2%. The energy activation values of HER was determined in an aqueous solution of BMI.BF₄ 10 vol.%, using platinum (23.40 kJ mol⁻¹) and Mo (9.22 kJ mol⁻¹) as electrocatalysts. The results show that the hydrogen production in IL electrolyte can be carried out with cheap material at room temperature, which makes this method economically attractive.     

A novel process to prepare porous membranes comprising SnO2 nanoparticles and P(MMA-AN) as polymer electrolyte

We have successfully developed a new process to prepare porous poly(methyl methacrylate-co-acrylonitrile) (P(MMA-AN)) copolymer based gel electrolyte. The porous structure in the polymer matrix is achieved by adding SnO₂ nanoparticles which are mostly used as gas sensor materials. The quasi-aromatic solvent, NMP, has an electron-repulsion effect with the space charge layer on the surface of SnO₂ nanoparticles and forms a special gas–liquid phase interface. Once the cast polymer solution is stored at an elevated temperature to evaporate the solvent, gas–liquid phase separation happens and spherical pores are obtained. The ionic conductivity at room temperature of the prepared gel polymer electrolyte based on the porous membrane is as high as 1.54 × 10⁻³ S cm⁻¹ with the electrochemical stability up to 5.10 V (vs. Li/Li⁺). This method presents another promising way to prepare porous polymer electrolyte for practical use.     

A new promising high temperature lithium battery solid electrolyte

Lithium lanthanoid silicates find importance as a solid electrolyte in high temperature lithium batteries in view of its high ionic conductivity at high temperatures. An first ever attempt is made to synthesis a new high temperature solid electrolyte viz., lithium samarium holmium silicate by sol–gel process and it has been characterized by thermal analysis (TGA–DTA), X-ray diffraction (XRD), infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Lithium ion conductivity of 0.8087 × 10⁻⁷ Ω⁻¹ cm⁻¹ at 25 °C was obtained and it increases with increasing temperature. For the first time a highest conductivity of 0.1095 × 10⁻² Ω⁻¹ cm⁻¹ was obtained at 850 °C which is high compared to other high temperature lithium battery solid electrolytes.     

Nanocrystalline FeWO4 as a pseudocapacitive electrode material for high volumetric energy density supercapacitors operated in an aqueous electrolyte

Iron tungstate (FeWO₄) has been synthesized using two low-temperature synthetic routes and investigated as a new pseudocapacitive electrode material for supercapacitors operating in a neutral aqueous electrolyte. Its electrochemical properties are clearly related to the specific surface area and seem to originate from Fe^3 +/Fe^2 + fast surface reactions. For FeWO₄ obtained by polyol-mediated synthesis, a high volumetric capacitance of 210 F·cm^− 3 (i.e. more than two times higher than that of activated carbon) was measured at 20 mV·s^− 1 with less than 5% fade over 10,000 cycles. Furthermore, unlike most of the previously investigated iron based electrodes, a unique pseudocapacitive behavior is observed, thus emphasizing the role of the crystallographic structure on the electrochemical signature.     

Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Vibrational spectroscopic study of syngenite formed during the treatment of liquid manure with sulphuric acid

Syngenite (K₂Ca(SO₄)₂·H₂O), formed during treatment of manure with sulphuric acid, was studied by infrared, near-infrared (NIR) and Raman spectroscopy. C_s site symmetry was determined for the two sulphate groups in syngenite (P2₁/m), so all bands are both infrared and Raman active. The split ν₁ (two Raman+two infrared bands) was observed at 981 and 1000 cm⁻¹. The split ν₂ (four Raman+four infrared bands) was observed in the Raman spectrum at 424, 441, 471 and 491 cm⁻¹. In the infrared spectrum, only one band was observed at 439 cm⁻¹. From the split ν₃ (six Raman+six infrared) bands three 298 K Raman bands were observed at 1117, 1138 and 1166 cm⁻¹. Cooling to 77 K resulted in four bands at 1119, 1136, 1144 and 1167 cm⁻¹. In the infrared spectrum, five bands were observed at 1110, 1125, 1136, 1148 and 1193 cm⁻¹. From the split ν₄ (six infrared+six Raman bands) four bands were observed in the infrared spectrum at 604, 617, 644 and 657 cm⁻¹. The 298 K Raman spectrum showed one band at 641 cm⁻¹, while at 77 K four bands were observed at 607, 621, 634 and 643 cm⁻¹. Crystal water is observed in the infrared spectrum by the OH-liberation mode at 754 cm⁻¹, OH-bending mode at 1631 cm⁻¹, OH-stretching modes at 3248 (symmetric) and 3377 cm⁻¹ (antisymmetric) and a combination band at 3510 cm⁻¹ of the H-bonded OH-mode plus the OH-stretching mode. The near-infrared spectrum gave information about the crystal water resulting in overtone and combination bands of OH-liberation, OH-bending and OH-stretching modes.     

Novel core–shell SDC/amorphous Na2CO3 nanocomposite electrolyte for low-temperature SOFCs

Novel core–shell SDC (Ce_0.8Sm_0.2O_1.9)/amorphous Na₂CO₃ nanocomposite was prepared for the first time. The core–shell nanocomposite particles are smaller than 100 nm with amorphous Na₂CO₃ shell of 4–6 nm in thickness. The nanocomposite electrolyte shows superionic conductivity above 300 °C, where the conductivity reaches over 0.1 S cm⁻¹. Such high conductive nanocomposite has been applied in low-temperature solid oxide fuel cells (LTSOFCs) with an excellent performance of 0.8 W cm⁻² at 550 °C. A new potential approach of designing and developing superionic conductors for LTSOFCs was presented to develop interface as ‘superionic highway’ in two-phase materials based on coated SDC.     

Electrically rechargeable zinc-oxygen flow battery with high power density

The development of a powerful, cyclically stable and electrically rechargeable zinc-oxygen battery with a three-electrode configuration is reported. A copper foam was used as stable substrate for zinc deposition in flowing potassium hydroxide electrolyte, while oxygen reduction and evolution were accomplished by a commercial silver electrode and a nickel foam, respectively. The cell could be charged and discharged with up to 600 mA cm^− 2, delivered a peak power density of 270 mW cm^− 2, and performed for more than 600 cycles, although short circuits by dendrite formation could not yet be completely avoided. At a current density of 50 mA cm^− 2 and a temperature of 30 °C, a promising energy efficiency of 54% was achieved.     

A cobalt-free electrode material La0.5Sr0.5Fe0.8Cu0.2O3 − δ for symmetrical solid oxide fuel cells

Cobalt-free perovskite oxide La_0.5Sr_0.5Fe_0.8Cu_0.2O_3 − δ (LSFC) was applied as both anode and cathode for symmetrical solid oxide fuel cells (SSOFCs). The LSFC shows a reversible transition between a cubic perovskite phase in air and a mixture of SrFeLaO₄, a K₂NiF₄-type layered perovskite oxide, metallic Cu and LaFeO₃ in reducing atmosphere at elevated temperature. The average thermal expansion coefficient of LSFC in air is 17.7 × 10^− 6 K^− 1 at 25 °C to 900 °C. By adopting LSFC as initial electrodes to fabricate electrolyte supported SSOFCs, the cells generate maximum power output of 1054, 795 and 577 mW cm^− 2 with humidified H₂ fuel (~ 3% H₂O) and 895, 721 and 482 mW cm^− 2 with humidified syngas fuel (H₂:CO = 1:1) at 900, 850 and 800 °C, respectively. Moreover, the cell with humidified H₂ fuel demonstrates a reasonable stability at 800 °C under 0.7 V for 100 h.