Solubility of CO2 in the ionic liquid [hmim][Tf2N]

New experimental results are presented for the total pressure above liquid mixtures of carbon dioxide and the ionic liquid 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([hmim][Tf₂N]). The series of experiments were performed at preset temperature and liquid phase composition by means of a very precise high-pressure view-cell technique based on the synthetic method. A temperature range from (293.15 to 413.2) K was investigated where the maximum pressure reached approximately 10 MPa. Gas molalities in [hmim][Tf₂N] ranged up to about 4.7 mol · kg⁻¹. The (extended) Henry’s law is successfully applied to correlate the solubility pressures.     

Direct electrochemistry of hemoglobin and its electrocatalytic effect based on its direct immobilization on carbon ionic liquid electrode

Direct electrochemistry of hemoglobin (Hb) has been achieved by its direct immobilization on carbon ionic liquid electrode (CILE). CILE was immersed in a solution containing Hb and ionic liquid, octylpyridinium chloride ([OcPy][Cl]), to directly immobilize Hb on CILE. Cyclic voltammetry of modified electrode exhibited quasi-reversible peaks corresponding to Hb. The oxidation and reduction peak potentials of immobilized Hb in acetate buffer solution, pH 5.0 and at a scan rate of 0.1 V s⁻¹ were obtained at about –150 mV and –290 mV, respectively. The average surface coverage of the electroactive Hb adsorbed on the electrode surface was calculated as 8.4 × 10⁻¹¹ mol cm⁻². Hb retained its bioactivity on modified electrode and showed excellent electrocatalytic activity towards oxygen, hydrogen peroxide and nitrite. Hydrogen peroxide can be determined in the range of 1.0 × 10⁻⁴–5.0 × 10⁻³ M.     

Isobaric vapor–liquid equilibria for ethanol–water system containing different ionic liquids at atmospheric pressure

Isobaric vapor–liquid equilibrium (VLE) data for ethanol–water systems containing ionic liquids (ILs) 1-methyl-3-methylimidazolium dimethylphosphate ([MMIM][DMP]), 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP]), 1-butyl-3-methylimidazolium bromide ([BMIM][Br]), 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF₆]) at atmospheric pressure (101.32 kPa) were measured with a circulation still. The results showed that the VLE of ethanol–water systems in the presence of different ILs was obviously different from that of the IL-free system. All ILs studied showed a salting-out effect, which gave rise to a change of the relative volatility of ethanol, and even to an elimination of the azeotropic point. It was found that the salting-out effect followed the order of [BMIM][Cl] > [BMIM][Br] > [BMIM][PF₆] and [MMIM][DMP] > [EMIM][DEP], which was ascribed to the preferential solvation ability of the ions resulting from the dissociation of the IL.     

Activity and stability of horseradish peroxidase in hydrophilic room temperature ionic liquid and its application in non-aqueous biosensing

The activity and stability of horseradish peroxidase (HRP) were investigated in a hydrophilic room temperature ionic liquid 1-butyl-3-methylimidazolium tetrafluroborate ([bmim][BF₄]) by electrochemical methods. Although no detectable activity exhibited in anhydrous [bmim][BF₄], HRP was active in the presence of a small amount of water (4.53%, v/v). And its activity can be improved by immobilization in agarose hydrogel. The immobilized HRP possesses excellent activity at 65 °C. It remained 80.2% of its initial activity after being immersed for 10.5 h in an aqueous mixture of [bmim][BF₄] with some hydrogen peroxide (H₂O₂) under room temperature, implying extremely high stability. Moreover, the immobilized HRP was found to be very sensitive and stable in H₂O-containing [bmim][BF₄] for the detection of H₂O₂, with a wide linear range of 6.10 × 10⁻⁷ to 1.32 × 10⁻⁴ mol l⁻¹ and low detection limit of 1.0 × 10⁻⁷ mol l⁻¹.     

Phase equilibria of didecyldimethylammonium nitrate ionic liquid with water and organic solvents

The phase diagrams for binary mixtures of an ammonium ionic liquid, didecyldimethylammonium nitrate, [DDA][NO₃], with: alcohols (propan-1-ol, butan-1-ol, octan-1-ol, and decan-1-ol): hydrocarbons (toluene, propylbenzene, hexane, and hexadecane) and with water were determined in our laboratory. The phase equilibria were measured by a dynamic method from T = 220 K to either the melting point of the ionic liquid, or to the boiling point of the solvent. A simple liquidus curve in a eutectic system was observed for [DDA][NO₃] with: alcohols (propan-1-ol, butan-1-ol, and octan-1-ol); aromatic hydrocarbons (toluene and propylbenzene) and with water. (Solid + liquid) equilibria with immiscibility in the liquid phase were detected with the aliphatic hydrocarbons heptane and hexadecane and with decan-1-ol. (Liquid + liquid) equilibria for the system [DDA][NO₃] with hexadecane was observed for the whole mole fraction range of the ionic liquid. The observation of the upper critical solution temperature in binary mixtures of ([DDA][NO₃] + decan-1-ol, heptane, or hexadecane) was limited by the boiling temperature of the solvent.Characterisation and purity of the compounds were determined by elemental analysis, water content (Fisher method) and differential scanning microcalorimetry (d.s.c.) analysis. The d.s.c. method of analysis was used to determine melting temperatures and enthalpies of fusion. The thermal stability of the ionic liquid was resolved by the thermogravimetric technique–differential thermal analysis (TG–DTA) technique over a wide temperature range from (200 to 780) K. The thermal decomposition temperature of 50% of the sample was greater than 500 K.The (solid + liquid) phase equilibria, curves were correlated by means of different G^Ex models utilizing parameters derived from the (solid + liquid) equilibrium. The root-mean-square deviations of the solubility temperatures for all calculated data are dependent upon the particular system and the particular equation used. Comparison of the solubilities of different ammonium salts in alcohols, in hexane, in benzene, and in water are discussed.     

Silver particle-decorated carbon paste electrode based on ionic liquid for improved determination of nitrite

A simple silver particle-modified carbon paste electrode is proposed for the determination of low concentration levels of nitrite ions. The electrode consists of a carbon powder decorated with silver sub-micrometre particles (AgPs) and a hydrophobic ionic liquid trihexyltetradecylphosphonium chloride as a binder. It has been shown that AgPs exhibit a strong electrocatalytic effect on the nitrite oxidation. For optimal electroanalytical performance the electrode was conditioned via silver oxidation/reduction cycle. The electrode revealed a linear square-wave voltammetric response in a wide examined concentration range of 0.05 to 1.0 mmol L^− 1, limit of detection (LOD) of 3 μmol L^− 1 and excellent repeatability with RSD of 0.3%.     

Direct electrochemical response of Myoglobin using a room temperature ionic liquid, 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate,as supporting electrolyte

Direct electrochemical response of Myoglobin (Myb) at the basal plane graphite (BPG) electrode was observed when a room temperature ionic liquid (RTIL), 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate ([HEMIm][BF₄]), was used as the supporting electrolyte. In a 0.17 M [HEMIm]BF₄ aqueous solution, a couple of well-defined redox peaks of Myb could be obtained, whose anodic and cathodic peak potentials were at −0.158 and −0.224 V (vs. Ag/AgCl), respectively. Both anodic and cathodic peak currents increased linearly with the potential scan rate. Compared with the supporting electrolyte of phosphate buffer, [HEMIm][BF₄] played an obvious promotion for the direct electron transfer between Myb and the BPG electrode. Further investigation suggested that Myb was adsorbed tightly on the surface of the BPG electrode in the presence of [HEMIm][BF₄] to form a stable, approximate monolayer Myb film. Myb adsorbed on the BPG electrode surface showed a remarkable electrocatalytic activity for the reduction of oxygen in a [HEMIm][BF₄] aqueous solution. Based on these, a third-generation biosensor could be constructed to directly detect the concentration of oxygen in aqueous solution with a limit of detection of 2.3 × 10⁻⁸ M.     

Quasi in situ XPS study of anion intercalation into HOPG from the ionic liquid [EMIM][BF4]

Highly oriented pyrolytic graphite (HOPG) electrodes were electrochemically oxidized in the ionic liquid [EMIM][BF₄]. Both, the electrolyte and the electrode surface were investigated using X-ray photoelectron spectroscopy (XPS) after electrochemical treatment. For that purpose an electrochemical preparation chamber was attached to the ultra high vacuum system allowing for preparation of electrodes in non-aqueous electrolyte and subsequent sample transfer under inert nitrogen atmosphere. The XP-spectra of all species detected on the oxidized HOPG surface show core level shifts towards lower binding energies referring to a Fermi level shift and proving that a graphite intercalation compound was formed. Anion intercalation occurs together with co-intercalation of cations at 2 V vs. carbon quasi-reference electrode and is found to be irreversible. XPS analysis of the ionic liquid prior to and after electrochemical treatment indicates a change in electrolyte composition.     

Micro-electrodeposition in the presence of ionic liquid for the preconcentration of trace amounts of Fe,Co, Ni and Zn from aqueous samples

The paper presents the preconcentration of trace elements via electrodeposition onto a (micro)aluminum cathode in the presence of ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF₆] as a supporting electrolyte. The advantages of the proposed method include very simple instrumentation for the preconcentration of trace elements and low-cost reagents. The experiment showed that the use of ionic liquid in the electrodeposition process significantly improves sensitivity, recovery and detection limits for the determination of trace amounts of iron, cobalt, nickel and zinc. The preconcentrated metals were determined using X-ray fluorescence spectrometry. The optimum parameters for electrodeposition such as pH, the volume of the analyzed solution, the voltage and the deposition time were studied. Under the optimized conditions, the detection limits were 5, 2, 3 and 6 μg L^− 1 for iron, cobalt, nickel and zinc, respectively. The precision and recovery of the method were in the range of 3–5.5%, and 92–103%, respectively. The calibration was performed using aqueous standards of Fe(III), Co(II), Ni(II) and Zn(II) in the range 0.01–0.25 mg L^− 1. The method was applied successfully in water analysis.     

(Liquid + liquid) extraction of methanol from alkanes using dialkylphosphate-based ionic liquids as solvents

In this work, the feasibility of ionic liquids (ILs), 1,3-dimethylimidazolium dimethylphosphate ([MMIM][DMP]), 1-ethyl-3-methylimidazolium diethylphosphate ([EMIM][DEP]), and 1-butyl-3-methylimidazolium dibutylphosphate ([BMIM][DBP]), as solvents for the extraction of methanol from its mixtures with hexane and heptane was analyzed. The knowledge of (liquid + liquid) equilibria (LLE) of these mixtures is necessary for the design of the extraction separation process. Hence, the LLE data for the ternary systems, {methanol + hexane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, and {methanol + heptane + ([MMIM][DMP], or [EMIM][DEP], or [BMIM][DBP])}, were measured at T = 298.2 K and atmospheric pressure. The experimental results were correlated with the thermodynamic nonrandom two-liquid (NRTL) model. The solute distribution ratios of methanol and methanol/alkane selectivities, derived from the experimental LLE data, were calculated and analyzed to evaluate the capability of the studied ILs to accomplish the separation target. Meanwhile, these capabilities were also compared with that of other ILs obtained from the literature.     

Electro-reduction of cuprous chloride powder to copper nanoparticles in an ionic liquid

Cyclic voltammetry of the CuCl powder in a cavity microelectrode revealed direct electro-reduction in solid state in 1-butyl-3-methylimidazolium hexafluorophosphate. Potentiostatic electrolysis of the salt powder (attached to a current collector) in the ionic liquid produced Cu nanoparticles as confirmed by X-ray diffraction, energy dispersive X-ray analysis, scanning and transmission electron microscopy. The particle size decreased down to 10 nm when the electrode potential was shifted from −0.9 V to −1.8 V (versus Ag/Ag⁺). The electro-reduction and the nanoparticle formation mechanisms were investigated in the ionic liquid and also in aqueous 0.1 mol L⁻¹ KClO₄ in which larger Cu particles were obtained.     

Study of the solubility of CO2, H2S and their mixture in the ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate: Experimental and modelling

New experimental results are presented for the solubility of carbon dioxide, hydrogen sulfide in the ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈mim][PF₆]) at temperatures range from (303.15 to 353.15) K and pressures up to about 2 MPa. The solubility of the mixture of CO₂/H₂S in [C₈mim][PF₆] under various feed compositions were also measured at temperatures of (303.15, 323.15 and 343.15) K and the pressure up to 1 MPa. The solubility of carbon dioxide and hydrogen sulfide increased with increasing pressure and decreased with increasing temperature and the solubility of H₂S is about three times that of CO₂ in the particular ionic liquid studied. The measured data were correlated using extended Henry’s law included Pitzer’s virial expansion for the excess Gibbs energy, and the generic Redlich–Kwong cubic equation of state proposed for gas/ionic liquid systems. The correlations from the two models show quite good consistency with the experimental data for CO₂/IL and H₂S/IL binary mixtures within experimental uncertainties. For CO₂/H₂S/IL ternary mixtures, the RK model shows better correlation with the experimental values. We also studied the effect of cation alkyl chain length on the CO₂ and H₂S solubility by comparison of the experimental data of this study with those of previous reports. As the cation alkyl chain length became longer, the solubility of CO₂ and H₂S increased in the ionic liquid. Additionally, the influence of the anion on the solubility is studied by comparing the solubility of CO₂ and H₂S in [C₈mim][PF₆] with those in [C₈mim][Tf₂N]. As a result, CO₂ and H₂S have higher solubility in the IL with [Tf₂N]⁻ as the anion.     

Low-viscosity and low-melting point asymmetric trialkylsulfonium based ionic liquids as potential electrolytes

Nine new ionic liquids based on small asymmetric trialkylsulfonium cations with TFSI⁻ anion were prepared and characterized. Physical and electrochemical properties of these ionic liquids, including melting point, thermal stability, viscosity, conductivity and electrochemical window were determined. Reducing symmetry of cations reduces the melting points of these ILs. Some of these hydrophobic ionic liquids showed low-viscosity and low-melting point characteristics. The viscosities of S₂₂₃TFSI, S₂₂₁TFSI and S₁₂₃TFSI were 33, 36 and 39 mPa s at 25 °C, respectively. Electrochemical and thermal stabilities of these ILs permitted them to become promising electrolytes used in electrochemical devices.     

Molybdenum electrodes for hydrogen production by water electrolysis using ionic liquid electrolytes

The hydrogen production by water electrolysis was tested with different electrocatalysts (molybdenum, nickel, iron alloys containing chromium, manganese and nickel) using aqueous solutions of ionic liquid (IL) like 1-butyl-3-methylimidazolium tetrafluoroborate (BMI.BF₄). The hydrogen evolution reaction (HER) was performed at room temperature in a potential of −1.7 V (PtQRE). A Hoffman cell apparatus was used to water electrolysis with current density values, j, between 14.6 mA cm⁻² (for Ni electrode) and 77.5 mA cm⁻² (for Mo electrode). The system efficiency was very high for all electrocatalysts tested, between 97.0% and 99.2%. The energy activation values of HER was determined in an aqueous solution of BMI.BF₄ 10 vol.%, using platinum (23.40 kJ mol⁻¹) and Mo (9.22 kJ mol⁻¹) as electrocatalysts. The results show that the hydrogen production in IL electrolyte can be carried out with cheap material at room temperature, which makes this method economically attractive.     

Direct electrochemistry of single-stranded DNA on an ionic liquid modified carbon paste electrode

Electrochemical oxidation of thermally denatured single-stranded DNA (ssDNA) was studied on a room temperature ionic liquid N-butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (IL-CPE). A distinct oxidation peak appeared at +0.772 V (vs. SCE) on the IL-CPE after preconcentration of ssDNA at +0.35 V for 160 s in pH 7.0 phosphate buffer solution (PBS), which was attributed to the oxidation of guanine residue on the ssDNA molecular structure. The results showed an apparent negative shift of the oxidation peak potential and a great enhancement of the oxidation peak current on the IL-CPE compared with that of CPE. The electrochemical parameters of ssDNA on the IL-CPE were further calculated. Under the selected conditions, a linear calibration curve for ssDNA detection was obtained in the concentration range from 10.0 to 110.0 μg mL⁻¹ with the detection limit of 1.5 μg mL⁻¹(3σ).     

Li/LiFePO4 batteries with room temperature ionic liquid as electrolyte

Room temperature ionic liquid (RTIL) was prepared on basis of N-methyl-N-butylpiperidinium bis(trifluoromethanesulfonyl)imide (PP₁₄TFSI), which showed a wide electrochemical window (?0.1–5.2 V vs. Li⁺/Li) and is theoretically feasible as an electrolyte for batteries with metallic Li as anodes. The addition of vinylene carbonate (VC) improved the compatibility of PP₁₄TFSI-based electrolyte towards lithium anodes and enhanced the formation of solid electrolyte interphase film to protect lithium anodes from corrosion. Accordingly, Li/LiFePO₄ cells initially delivered a discharge capacity of about 127 mAh g^?1 at a current density of 17 mA g^?1 in the ionic liquid with the addition of VC and showed better cyclability than in the neat ionic liquid. Electrochemical impedance spectroscopy disclosed that the addition of VC enhanced Li-ion diffusion and depressed interfacial resistance significantly.     

Outstanding room-temperature capacitance of biomass-derived microporous carbons in ionic liquid electrolyte

A remarkable capacitance of 180 F·g^− 1 (at 5 mV·s^− 1) in solvent-free room-temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, was achieved in symmetric supercapacitors using microporous carbons with a specific surface area of ca. 2000 m²·g^− 1 calculated from gas sorption by the 2D-NLDFT method. The efficient capacitive charge storage was ascribed to textural properties: unlike most activated carbons, high specific surface area was made accessible to the bulky ions of the ionic liquid electrolyte thanks to micropores (1–2 nm) enabled by fine-tuning chemical activation. From the industrial perspective, a high volumetric capacitance of ca. 80 F·cm^− 3 was reached in neat ionic liquid due to the absence of mesopores. The use of microporous carbons from biomass waste represents an important advantage for large-scale production of high energy density supercapacitors.     

Highly mesoporous and high surface area carbon: A high capacitance electrode material for EDLCs with various electrolytes

Activated carbon fibers (ACFs) with high surface area and highly mesoporous structure for electrochemical double layer capacitors (EDLCs) have been prepared from polyacrylonitrile fibers by NaOH activation. Their unique microstructural features enable the ACFs to present outstanding high specific capacitance in aqueous, non-aqueous and novel ionic liquid electrolytes, i.e. 371 F g⁻¹ in 6 mol L⁻¹ KOH, 213 F g⁻¹ in 1 mol L⁻¹ LiClO₄/PC and 188 F g⁻¹ in ionic liquid composed of lithium bis(trifluoromethane sulfonyl)imide (LiN(SO₂CF₃)₂, LiTFSI) and 2-oxazolidinone (C₃H₅NO₂, OZO), suggesting that the ACF is a promising electrode material for high performance EDLCs.     

Using ionic liquid [EMIM][CH3COO] as an enzyme-‘friendly’ co-solvent for resolution of amino acids

An ionic liquid (IL), 1-ethyl-3-methylimidazolium acetate [EMIM][CH₃COO], was used in 0–4.0 M (∼60% IL, v/v), as a nonvolatile organic medium for the enzymatic resolution of amino acids. When dl-phenylalanine methyl ester was studied as a model substrate, high enantiomeric excesses (ee) of l-amino acid were obtained in all ionic concentrations; however, lower yields were observed at high IL concentrations. This IL is more enzyme-‘friendly’ than the hydrophilic organic solvent acetonitrile and those ILs containing chaotropic anions (such as [EMIM][OTs]). Among three proteases and two lipases investigated, lyophilized Bacillus licheniformis protease exhibited the best enantioselectivity and activity. Highly enantioselective resolutions were also produced for several other amino acids in 2.0 M IL. Interestingly, high ee were also found in deuterium oxide (D₂O) rather than in ordinary water, and a further enhancement was achieved with the co-existence of [EMIM][CH₃COO]. The heavy water effect was explained in terms of protein stabilization by D₂O. The secondary structural changes of enzyme in various media were interpreted by the second derivatives of FT-IR spectra.     

Study on the enthalpy of solution and enthalpy of dilution for the ionic liquid [C3mim][Val] (1-propyl-3-methylimidazolium valine)

A new amino acid ionic liquid (AAIL) [C₃mim][Val] (1-propyl-3-methylimidazolium valine) was prepared by the neutralization method. Using the solution-reaction isoperibol calorimeter, molar solution enthalpies of the ionic liquid [C₃mim][Val] with known amounts of water and with different concentrations in molality were measured at T = 298.15 K. In terms of standard addition method (SAM) and Archer’s method, the standard molar enthalpy of solution for [C₃mim][Val] without water, ${\mathrm{\Delta }}_{\text{s}}{H}_{\text{m}}^{\circ }$ = (−55.7 ± 0.4) kJ · mol⁻¹, was obtained. The hydration enthalpy of the cation [C₃mim]⁺, ΔH₊ ([C₃mim]⁺) = −226 kJ · mol⁻¹, was estimated in terms of Glasser’s theory. Using the RD496-III heat conduction microcalorimeter, the molar enthalpies of dilution, Δ_DH_m(m_i → m_f), of aqueous [C₃mim][Val] with various values of molality were measured. The values of Δ_DH_m(m_i → m_f) were fitted to Pitzer’s ion-interaction model and the values of apparent relative molar enthalpy, ^φL, calculated using Pitzer’s ion-interaction model.