Carbon nanotubes contain residual metal catalyst nanoparticles even after washing with nitric acid at elevated temperature because these metal nanoparticles are sheathed by several graphene sheets

It is demonstrated that multiwalled (MWCNT) and single-walled (SWCNT) carbon nanotube materials contain residual metal impurities (Fe, Ni, Co, Mo) even after prolonged periods of "washing" with concentrated nitric acid at temperature of 80 degrees C. Transmission electron microscopy (TEM) and high-resolution TEM (HR-TEM) reveals that this is because such metal impurities are intercalated in the nanotube channel (in the case of MWCNT) or in the "bamboo" segment of the nanotube (in the case of "bamboo"-like MWCNT), or they create graphene sheet protected metal core/shell nanoparticles (in the case of SWCNT). TEM/energy-dispersive X-ray spectroscopy (TEM/EDS) elucidate that residual metal impurities presented in "washed" carbon nanotube materials are in some cases in the form of metal alloys or that there can be several different pure metal nanoparticles presented in one CNT material. It is shown by thermogravimetric analysis that "washing" with concentrated nitric acid removes up to 88% (w/w) of metal catalyst nanoparticles from as-received carbon nanotubes and that such removal has in some cases a significant effect on the electrochemical reduction of hydrogen peroxide.     

Electrowetting of aligned carbon nanotube films

Electrowetting is one approach to reducing the interfacial tension between a solid and a liquid. In this method, an electrical potential is applied across the solid/liquid interface which modifies the wetting properties of the liquid on the solid without changing the composition of the solid and liquid phases. Electrowetting of aligned carbon nanotube (CNT) films is investigated by the sessile drop method by dispensing deionized (DI) water or 0.03 M NaCl droplets (contacted by Au wire) onto aligned CNT films assembled on a copper substrate. The results demonstrate that electrowetting can greatly reduce the hydrophobicity of the aligned CNTs; the contact angle saturation for DI water and 0.03 M NaCl droplets occurs at 98 and 50 degrees , respectively. The combined effects of the geometrical roughness and the electrical potential on the contact angle are briefly discussed and modeled. Such a strategy may be invoked to controllably reduce the interfacial tension between carbon nanotubes (CNTs) and polymer precursors when infiltrating the monomers into the prealigned nanotube films.     

X-ray fluorescence as a method of monitoring metal catalyst content during the purification of carbon nanotubes

There have been several studies that suggest that catalyst metals in carbon nanotubes (CNTs) may pose a health threat. As there are many potential applications of CNTs in medicine, it is important to be able to quantitatively determine the amount of metal catalyst contained in a CNT sample. The relative catalyst content of carbon nanotube samples synthesized via arc-discharge has been determined at various stages of the purification process using X-ray fluorescence (XRF) analysis. Purification was achieved by immersing samples in heated nitric acid. The intensities of the nickel K_α X-rays were studied to determine the relative catalyst content in the samples. Scanning electron microscopy (SEM) images of purified nanotubes have been compared to the images of a sample that has been irradiated by 0-15 keV bremsstrahlung in order to determine if the XRF analysis of the nanotubes is in any way destructive. No obvious structural defects were observed as the result of irradiation.     

Separation of carbon nanotubes by frit inlet asymmetrical flow field-flow fractionation

Flow field-flow fractionation (flow FFF), a separation technique for particles and macromolecules, has been used to separate carbon nanotubes (CNT). The carbon nanotube ropes that were purified from a raw carbon nanotube mixture by acidic reflux followed by cross-flow filtration using a hollow fiber module were cut into shorter lengths by sonication under a concentrated acid mixture. The cut carbon nanotubes were separated by using a modified flow FFF channel system, frit inlet asymmetrical flow FFF (FI AFIFFF) channel, which was useful in the continuous flow operation during injection and separation. Carbon nanotubes, before and after the cutting process, were clearly distinguished by their retention profiles. The narrow volume fractions of CNT collected during flow FFF runs were confirmed by field emission scanning electron microscopy and Raman spectroscopy. Experimentally, it was found that retention of carbon nanotubes in flow FFF was dependent on the use of surfactant for CNT dispersion and for the carrier solution in flow FFF. In this work, the use of flow FFF for the size differentiation of carbon nanotubes in the process of preparation or purification was demonstrated.     

Electron transport through carbon nanotube intramolecular heterojunctions with peptide linkages

We present a systematic analysis of electron transport characteristics of carbon nanotube (CNT) intramolecular heterojunctions with peptide linkages, MM, SS, SM1, and SM2 where M and S stand for metallic and semiconducting CNT electrodes, respectively. Our theoretical investigations show that the incorporation of peptide linkages and their associated dipole moments play an important role in determining the electron transport characteristics and lead to materials with unique properties, such as Schottky-like behavior. Furthermore, we show that the Schottky-like behavior is observed in our SM1 junction but not in the SM2 junction because of the different effects that arise from both the direction and strength of their dipole moments. We believe that our results will pave the way towards the design and implementation of various electronic logic functions based on carbon nanotubes for applications in the field of nanoelectronics.     

Determination of organophosphate pesticides at a carbon nanotube/organophosphorus hydrolase electrochemical biosensor

An amperometric biosensor for oganophosphorus (OP) pesticides based on a carbon nanotube (CNT)-modified transducer and an organophosphorus hydrolase (OPH) biocatalyst is described. A bilayer approach with the OPH layer atop of the CNT film was used for preparing the CNT/OPH biosensor. The CNT layer leads to a greatly improved anodic detection of the enzymatically generated p-nitrophenol product, including higher sensitivity and stability. The sensor performance was optimized with respect to the surface modification and operating conditions. Under the optimal conditions the biosensor was used to measure as low as 0.15 μM paraoxon and 0.8 μM methyl parathion with sensitivities of 25 and 6 nA/μM, respectively.     

Comparison of the properties of waterborne polyurethane/multiwalled carbon nanotube and acid‐treated multiwalled carbon nanotube composites prepared by in situ polymerization

A series of waterborne polyurethane (WBPU)/multiwalled carbon nanotube (CNT) and WBPU/nitric acid treated multiwalled carbon nanotube (A‐CNT) composites were prepared by in situ polymerization in an aqueous medium. The optimum nitric acid treatment time was about 0.5 h. The effects of the CNT and A‐CNT contents on the dynamic mechanical thermal properties, mechanical properties, hardness, electrical conductivity, and antistatic properties of the two kinds of composites were compared. The tensile strength and modulus, the glass‐transition temperatures of the soft and hard segments (T_gs and T_gh, respectively), and ΔT_g (T_gh − T_gs) of WBPU for both composites increased with increasing CNT and A‐CNT contents. However, these properties of the WBPU/A‐CNT composites were higher than those of the WBPU/CNT composites with the same CNT content. The electrical conductivities of the WBPU/CNT1.5 and WBPU/A‐CNT1.5 composites containing 1.5 wt % CNTs (8.0 × 10⁻⁴ and 1.1 × 10⁻³ S/cm) were nearly 8 and 9 orders of magnitude higher than that of WBPU (2.5 × 10⁻¹² S/cm), respectively. The half‐life of the electrostatic charge (τ_1/2) values of the WBPU/CNT0.1 and WBPU/A‐CNT0.1 composites containing 0.1 wt % CNTs were below 10 s, and the composites had good antistatic properties. From these results, A‐CNT was found to be a better reinforcer than CNT. These results suggest that WBPU/A‐CNT composites prepared by in situ polymerization have high potential as new materials for waterborne coatings with good physical, antistatic, and conductive properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3973–3985, 2005     

Tyrosine sensing on phthalic anhydride functionalized chitosan and carbon nanotube film coated glassy carbon electrode

Phthaloylchitosan (PHCS) has been synthesized by a simple and low-cost method using chitosan and phthalic anhydride as organic precursors by microwave irradiation. Techniques of nuclear magnetic resonance (NMR), FT-IR spectroscopy and transmission electron microscope (TEM) were used to characterize the structure and properties of the Phthaloylchitosan. Moreover, glassy carbon electrode modified with Phthaloylchitosan and carbon nanotube (PHCS–CNT/GCE) was prepared by casting of the PHCS–CNT solution on GCE. The electrochemical behavior of PHCS–CNT/GCE was investigated and compared with the electrochemical behavior of Phthaloylchitosan modified GC (PHCS/GC), carbon nanotube modified GC (CNT/GC) and unmodified GC using cyclic voltammetry (CV). The Phthaloylchitosan film is electrochemically inactive; similar background charging currents are observed at bare GC. Electrochemical parameters, including apparent diffusion coefficient for the Fe(CN)₆^3-/4- redox probe at PHCS–CNT/GCE is comparable to values reported for GCE, CNT/GCE and PHCS/GCE. The PHCS–CNT/GCE sensor responded linearly to tyrosine (Tyr) in the concentration of 1.0 × 10^–6 to 8.0 × 10^–4 M with detection limit of 3.0 × 10^–7 M at 3σ using amperometry. In addition, the PHCS–CNT/GCE displayed good reproducibility, high sensitivity and good selectivity towards the determination of Tyr, making it suitable for the determination of Tyr in clinical and medicine.     

Novel nanocomposite pervaporation membranes composed of poly(vinyl alcohol) and chitosan-wrapped carbon nanotube

Novel nanocomposite membranes (PVA–CNT(CS)) were prepared by incorporating chitosan-wrapped multiwalled carbon nanotube (MWNT) into poly(vinyl alcohol) (PVA). To further explore the intrinsic correlation between pervaporation performance and free volume characteristics, molecular dynamics simulation was first introduced to qualitatively analyze the contribution of carbon nanotube incorporation on improving free volume characteristics of the nanocomposite membranes. Secondly, the pervaporation performance of PVA–CNT(CS) nanocomposite membranes was investigated using permeation flux and separation factor as evaluating parameters. For benzene/cyclohexane (50/50, w/w) mixtures at 323 K, permeation flux and separation factor of pure PVA membrane are only 20.3 g/(m² h) and 9.6, respectively, while the corresponding values of PVA–CNT(CS) (CNT content: 1%) nanocomposite membrane are 65.9 g/(m² h) and 53.4. In order to explain the simultaneous increase of permeation flux and separation factor, as well as to check the calculation reliability of molecular dynamics simulation, positron annihilation lifetime spectroscopy (PALS) analysis was employed.     

Effects of carbon nanotube functionalization on the agglomeration and sintering of supported Pd nanoparticles

The size of carbon nanotube supported Pd and PdO nanoparticles was investigated on oxidatively functionalized multiwall carbon nanotubes. All samples were characterized by transmission electron microscopy, X-ray diffractometry, X-ray photoelectron spectroscopy and Raman spectroscopy. The average particle diameter calculated from TEM image analysis was found to be inversely proportional with the duration of the oxidation in nitric acid. Crystallite sizes determined from XRD patterns confirmed this general tendency.     

Studies of adsorption and total heterogeneity properties of pure and modified carbon nanotube surfaces

Modified carbon multiwall nanotubes were prepared via the oxidation process by means of 65 % nitric acid and/or ferric nitrate dissolved with 65 % nitric acid. Using special thermogravimetry (Q-TG), sorptometry, and AFM methods physicochemical properties of pure and modified nanotube surfaces were investigated. A numerical and analytical procedure for the evaluation of total heterogeneous properties on the basis of liquid thermodesorption from the sample surfaces under the quasi-equilibrium conditions is presented. The calculations of the fractal dimensions of carbon nanotubes using the thermogravimetry Q-TG, sorptometry, and AFM data are presented.     

Studies of modified carbon nanotubes by means of thermogravimetry Q-TG and sorptometry techniques

The paper presents the physicochemical (adsorption and porosity) properties of closed carbon nanotubes, opened through the action of an oxidizing acid and modified with metal ions of nickel, cobalt, and iron/cobalt. The carbon nanotubes were prepared via the oxidation process by means of 65 % nitric acid and/or nickel and cobalt nitrates dissolved with 65 % nitric acid. Using special thermogravimetry Q-TG and sorptometry methods physicochemical properties of pure and modified nanotube surfaces were investigated. A numerical and analytical procedure for the evaluation of heterogeneous properties (adsorption capacity, statistical number of adsorbed liquid layers, desorption energy distribution functions) on the basis of liquid thermodesorption Q-TG from the sample surfaces under the quasi-equilibrium conditions are presented. The calculations of the specific surface areas, pore size and volume, and fractal dimensions of carbon nanotubes were made from sorptometry data.     

Design and characterization of three-dimensional carbon nanotube foams

We demonstrate a new method that makes use of colloidal silica templates to fabricate porous three-dimensional architectures of carbon nanotubes (CNTs). CNTs were grown on monolayered and multilayered structures of colloidal silica using chemical vapor deposition. Porous CNT membranes and three-dimensional carbon nanotube foams were obtained by treating these silica-CNTs structures with HF. The membranes and foams of CNT so obtained were chemically and mechanically stable and were characterized by using scanning electron microscopy and energy dispersive spectroscopy.     

Novel in situ fabrication of chestnut-like carbon nanotube spheres from polypropylene and nickel formate

A novel in situ approach to mass fabrication of carbon nanotubes was reported. Composites of polypropylene (PP)/organomontmorillonite (OMMT)/nickel formate (NF) were prepared by mixing these components in a Brabender mixer at an elevated temperature. Chestnut-like carbon nanotube (CNT) spheres were in situ fabricated in high yields by heating the PP/OMMT/NF composites at 900 degrees C without adding any additional pre-synthesized nickel nanocatalysts. The products were studied by X-ray diffractometer (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Raman spectroscopy, and N2 adsorption-desorption measurements. The results showed that nickel nanoparticles were in situ produced, which catalyzed the formation of multiwalled carbon nanotubes (MWNTs) in an autoclave-like microreactor formed by OMMT. These in situ formed nickel nanoparticles were found to be more catalytically active than pre-synthesized nickel nanocatalysts, resulting in higher yields of CNTs. The obtained CNT spheres have a high surface area, which makes them a good catalyst support. Loading of metal nanoparticles was preliminarily tried, and Pt nanoparticles of ca. 2.65 nm in size were successfully deposited on CNTs. The applications of these nanocatalysts in chemical reactions are currently being studied in our laboratory.     

Poly(lactic acid) composites with poly(lactic acid)‐modified carbon nanotubes

This work reports the study of the effect of chemical functionalization of carbon nanotubes on their dispersion in poly(lactic acid). The nanotubes were functionalized by the 1,3‐dipolar cycloaddition reaction, generating pyrrolidine groups at the nanotube surface. Further reaction of the pyrrolidine groups with poly(lactic acid) was studied in solution and in the polymer melt. The former involved refluxing the nanotubes in a dimethylformamide/polymer solution; the latter was carried out by direct melt mixing in a microcompounder. The carbon nanotubes collected after each process were characterized by thermogravimetry and by X‐ray photoelectron spectroscopy, showing evidence of polymer bonded to the nanotube surface only when the reaction was carried out in the polymer melt. The composites with polymer modified nanotubes present smaller average agglomerate area and a narrower agglomerate area distribution. In addition, they show improved tensile properties at low CNT concentration and present lower electrical resistivity. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3740–3750     

Synthesis and characterization of unbranched and branched multi-walled carbon nanotubes using Cu as catalyst

Unbranched and branched carbon nanotubes (CNTs) were synthesized by catalytic chemical vapor deposition from methane at 900 °C over a Cu/MgO catalyst. Morphology and structure of the CNTs were characterized by scanning and transmission electron microscopy, and Raman spectroscopy. The effect of methane flow rate on the CNT growth was investigated. The results suggest that the products were transformed from unbranched to branched CNTs with an increase in methane flow rate. The simplicity and controllability of such a preparation technique make it a promising method to synthesize different carbon nanotube structures.     

Modifying the response of a polymer-based quartz crystal microbalance hydrocarbon sensor with functionalized carbon nanotubes

This report compares the performance of polymer and carbon nanotube-polymer composite membranes on a quartz crystal microbalance (QCM) sensor for the detection of aromatic hydrocarbons (benzene, toluene, ethylbenzene, p-xylene and naphthalene) in aqueous solutions. Several different polymers (polystyrene, polystyrene-co-butadiene, polyisobutylene and polybutadiene) and types of functionalized carbon nanotubes (multi-walled and single-walled carbon nanotubes) were investigated at varying carbon nanotube (CNT) loading levels and film thicknesses. In a majority of instances, the difference in response between membranes comprising pure polymer and membranes containing 10% (w/w) carbon nanotubes were not statistically significant. However, a notable exception is the decreasing sensitivity towards p-xylene with increasing carbon nanotube content in a polybutadiene film. This variation in sensitivity can be attributed to a change in the sorption mechanism from absorption into the polymer phase to adsorption onto the carbon nanotube sidewalls. With much thicker coatings of 10% (w/w) carbon nanotube in polybutadiene, the sensitivity towards toluene was higher compared to the pure polymer. The increased toluene sensitivity may be partially attributed to an increase in the sorption capacity of a carbon nanotube polymer composite film relative to its corresponding pure polymer film. Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) measurements were performed to understand the mechanism of sorption and these studies showed that the addition of functionalized CNT to the polymer increases the absorption of certain types of hydrocarbons. This study demonstrates that carbon nanotubes can be incorporated into a polymer-coated QCM sensor and that composite films may be used to modify the QCM response and selectivity during the analysis of complex hydrocarbon mixtures.     

Electrooxidation of ethanol on carbon nanotubes–nickel nanoparticles composites in alkaline media

In this report, the preparation of carbon nanotubes–Ni nanoparticles composites (CNT–Ni) is presented. The morphology and elemental composition of CNT–Ni composites were examined by transmission electron microscopy and X-ray diffraction. The electrochemical behaviour of carbon nanotubes–Ni nanoparticles composites in an aqueous solutions of alkali and alkaline solutions of ethanol has been studied by linear sweep voltammetry. The peak on the potentiodynamic curve for CNT–Ni composite electrode in alkaline solutions of ethanol is observed which is ascribed to the ethanol oxidation in alkaline medium. The results obtained are discussed from the point of view of employment of the CNT–Ni composites for the catalytic electrodes of fuel cells.     

The influence of nitrogen sources on nitrogen doped multi-walled carbon nanotubes

A range of nitrogen doped carbon nanotubes (N-CNTs) was produced by a nebulised floating catalyst method at 850 °C using a mixture of toluene and 1-8% nitrogen containing reagents (a range of amines and amides). The carbon nanotube (CNT) products were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA), CHN analysis as well as Raman spectroscopy. Differences due to the different N containing reagents were noted but in general all reagents gave aligned CNTs that at low concentration (1%) were longer and wider than those produced without nitrogen. Increased N content in the reactant mixture gave doped tubes that became shorter and showed more disorder. Treatment of the N-CNTs with nitric acid (microwave, 30 min) gave samples that were chemically modified by the acid (loss of alignment, narrower tubes and more facile oxidation). It appears in general that the amount of N in the nitrogen containing reagent is more important than the source and type of the N atoms used as revealed by trends in the morphology (diameter, length) of the N-CNTs produced.     

Fabrication of carbon nanotube sheets and their bilirubin adsorption capacity

Bilirubin adsorption on carbon nanotube surfaces has been studied to develop a new adsorbent in the plasma apheresis. Powder-like carbon nanotubes were first examined under various adsorption conditions such as temperatures and initial concentrations of bilirubin solutions. The adsorption capacity was measured from the residual concentrations of bilirubin in the solution after the adsorption process using a visible absorption spectroscopy. We found that multi-walled carbon nanotubes (MWCNTs) exhibit greater adsorption capacity for bilirubin molecules than that of single-walled carbon nanotubes (SWCNTs). To guarantee the safety of the adsorbents, we fabricated carbon nanotube sheets in which leakage of CNTs to the plasma is suppressed. Since SWCNTs are more suitable for robust sheets, a complex sheet consisting of SWCNTs as the scaffolds and MWCNTs as the efficient adsorbents. CNT/polyaniline complex sheets were also fabricated. Bilirubin adsorption capacity of CNTs has been found to be much larger than that of the conventional materials because of their large surface areas and large adsorption capability for polycyclic compound molecules due to their surface structure similar to graphite.