Comparisons of sorption of aquatic humic matter by DAX-8 and XAD-8 resins from solid-state (13)C NMR spectroscopy's point of view

Aquatic humic solutes were separated in parallel by the non-ionic macroporous DAX-8 and XAD-8 resins from four different fresh water sources. On average, the sorptive power of the DAX-8 resin does not differ systematically from that of the XAD-8 resin. The DAX-8 resin seems to have more precise column characteristics compared with the XAD-8 resin. There was no significant difference between the major elemental compositions of the parallel humic-solute bulks obtained by these two resins. According to the (13)C NMR spectroscopy the content and quality of aliphatic carbons, especially those representing terminal methyl groups or methylene carbons, were the most systematic and powerful discriminating factors between the humic extracts obtained by these two resins. Generally speaking the DAX-8 and XAD-8 resins seem to isolate humic-solute bulks almost equally, although the content of aliphatics is slightly greater for the former, producing mixtures with similar structural compositions for general purposes. The structural composition and quantity of the humic-solute mixture isolable with a weakly basic DEAE-cellulose anion exchange resin differs partially from any humic fraction obtained by non-ionic sorbing solids. The environmental impact was also visible on the quality of the structural fine-chemistry of the different humic isolates obtained both by the DAX-8 and XAD-8 resins.     

Synthesis and Application of a New Acrylic Ester Resin for Recycling SIPA from its Water Solution

A new acrylic ester polymer YWB-7 resin was prepared and characterized. The properties of YWB-7 resin were compared with those of the commercial Amberlite XAD-7, Diaion HP2MG and hypercrosslinked macroporous polymer NDA-150 resins. Both surface area and micropore area of YWB-7 resin were bigger than those of XAD-7 resin and HP2MG resin. The YWB-7 resin was successfully employed to recycle 5-sodiosulfoisophthalic acids （SIPA） from its solutions with and without methanol.     

Preparation and characterization of chelating resins loaded with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol for preconcentration of rare earth elements

 Chelating resins prepared by sorption of 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol (5-BrPADAP) on macroporous resins (Amberlite XAD-4 and XAD-7) were characterized. The adsorption properties (amount of chelating agent adsorbed per gram of resin, sorption kinetics, retention capacity, etc.) and the thermodynamic quantities of each adsorption process were determined. The retention of some rare earth elements (e.g. Er, Yb and Lu) on these chelating resins was studied in order to preconcentrate them for their determination by X-Ray fluorescence spectrometry. Received: 7 September 1995/Revised: 2 January 1996/Accepted: 10 January 1996     

STUDIES ON THE ADSORPTION OF PHENOLIC COMPOUNDS ON A PS-BASED RESIN MODIFIED BY NITRO FUNCTIONAL GROUPS

A new adsorbent (JN-01) was prepared by modifying resin NDA-1800 with nitro functional groups.The adsorption capacities of resins XAD-4,NDA-1800 and JN-01 were investigated,and the results indicated that the modified resin JN-01 was much better in adsorbing phenol,p-nitrophenol and p-cresol.The adsorption capacities of the resin JN-01 were higher than those of the resins XAD-4 and NDA-1800 within a temperature range of 283-323 K,which might be attributed to the higher surface area and the partial polarit...     

An Investigation on the Concentration Efficiencies of Some Macroreticular and Ambersorb Resins Using Radio-Labelled Organic Contaminants Commonly Encountered in Water

Abstract

The extraction efficiencies of the three commercially available Ambersorb®, carbonaceous, polymeric resins, XE-340, XE-347 and XE-348 were evaluated for their use as sorbents for environmental pollutants using four model, radio-labelled water-borne organic contaminants. Their accumulation behaviour was compared with that of the thoroughly-studied Amberlite®, macroreticular XAD-2 (hydrophobic) and XAD-7 (hydrophilic) resins. These model compounds were desorbed from the resins using known volumes of commonly-used solvents to select the solvent for a particular resin(s). In this preliminary study, at <4 μg/L concentrations of the labelled compounds in aqueous solution (pH 5.78), the order of extraction efficiency of the resins was found to be XAD-2 > XAD-7 > XE-340?-347?-348 for organics. Several inherent impurities originally present in the carbonaceous resins were desorbed by solvents during elution. These resins therefore required exhaustive soxhlet purification prior to use. Most of the impurities were identified by gas chromatography/mass spectrometry.     

Isolation of organic water pollutants by xad resins and carbon

The recovery efficiencies of XAD resins −2, −4, −7, and −8 and of resin mixtures were measured using distilled water samples containing 13 organic pollutants. An equal-weight mixture of XAD-4 and XAD-8 was most efficient. XAD-2 and XAD-4/8 were further terted and found effective using tapwater. Carbon was tested as a sorbent for materials not well retained by the resins. In-column solvent washing before sample sorption was found to be as effective as Soxhlet extraction for removing background impurities. Some compounds can be desorbed from carbon by in-column solvent elution; others require Soxhlet extraction. An XAD-4/8 column in series with a carbon column was used to sample 1000 1 of tapwater. Halomethanes, n-hydrocarbons, polynuclear aromatic compounds and dibenzofuran in the order of ng/l were identified using a gas chromatograph-mass spectrometer-computer system.     

Preparation of Amberlite XAD resins coated with dithiosemicarbazone compounds and preconcentration of some metal ions

The Amberlite XAD resins coated with dithiosemicarbazones were prepared and their collection behavior of metal ions from aqueous solution was investigated. Among the resins used, the reagent-loaded Amberlite XAD-7 was found to be superior for the collection of metal ions to other reagent-loaded resins used. The quantitative collection of mercury(II), palladium(II) and copper(II) was obtained from acidic medium, while cadmium(II) and lead(II) was obtained from neutral medium by the Amberlite XAD-7 resin coated with dimethylglyoxal bis(4-phenyl-3-thiosemicarbazone) (DMBS). These metal ions collected on the resin were easily eluted with a small volume of N,N-dimethylformamide as their DMBS chelates. This collection-elution method was applied to the determination of their metal ions by reversed-phase high performance liquid chromatography with a spectrophotometric detection.     

Removal of iodide from aqueous solutions by polyethylenimine-epichlorohydrin resins

The iodide removal from aqueous solutions (initial I^?-concentration: 300–5,000 mg/L) by a low and a high molecular weight polyethylenimine-epichlorohydrin resin was investigated both in absence and presence of background electrolytes (NaCl and Na₂SO₄, ionic strength due to background electrolyte 0.1 M) using a batch technique, ¹³¹I as radioactive tracer and high-resolution γ-ray spectrometry. The experiments in absence of background electrolyte were performed using solutions of initial pH 3 and 7, whereas those in presence using solutions of initial pH 3. The results, which demonstrated the high iodide-removal efficiency of both resins, were modeled using the Langmuir and Freundlich isotherm equations. The experimental data were better reproduced using the Langmuir equation. Using this equation maximum sorption capacity values (Q _max) of 638.8 and 603.3 mg/g were obtained for the high molecular weight resin from solutions of initial pH 3 and 7 respectively, whereas the corresponding values for the low molecular weight one were slightly lower (552.4 and 507.5 mg/g respectively). The iodide uptake by the resins strongly depended on the presence of competing anions and especially of sulfates. The examination of sections of the I-loaded resins grains by scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) revealed that iodine was evenly distributed throughout the bulk of the resins and not only bound to their surface.     

Flow microcalorimetry and competitive liquid sorption II. Liquid sorption and wetting on macroreticular hydrophilic/hydrophobic networks

Three different types of polymer networks (polymer resins) were investigated by flow microcalorimetry and selective liquid sorption from 1-propanol(1)-water(2) mixtures. Type 1 network structure is formed by non-polar, non-swelling, macroporous resins (Amberlite XAD-2, Amberlite XAD-4). The composite isotherms for alcohol sorption were S-shaped. 1-Propanol is preferentially sorbed up to x₁≈0.5. Macroreticular non-ionic resins, Amberlite XAD-7 and XAD-8, represent the second type of polymer structure. These particles have a considerable extent of swelling in the binary liquid mixture and 1-propanol was preferentially sorbed by the polymer. The composite isotherms were U-shaped and exhibit maxima and minima. The third type of network structure is attached to macroreticular polar, hydrophilic ion-exchange resins (Chelite-S, Amberlyste A-21). Depending on the composition range of the binary liquid mixture, the resins may swell to a different extent and water is preferentially embeded in the porous polymer network. The swelling of the polymer networks was monitored by the gravimetric technique in separate experiments. The sorption capacity determined from the liquid uptake of the resins was related to the sorption capacity derived from the reduced surface excess. The enthalpy effect accompanying the sorption process was determined by flow and immersion microcalorimetry. The enthalpy of displacement isotherms reveals differences in polarity and swelling ability of the polymer network fairly well. Structural changes in the adsorption layers and formation of alcohol-water clusters on the surfaces play an important role.     

Porous glass as an efficient adsorbent for volatile atmospheric polychlorinated biphenyl congeners

Porous glass is a more efficient adsorbent than Amberlite XAD-2 resin for volatile polychlorobiphenyls (PCB) in the atmospheric vapour phase. The adsorption efficiencies for individual PCB congeners are compared by analysis of the extracts by capillary gas chromatography (electron-capture detection); individual congeners are used as reference compounds. Efficiencies for some di-, tri- and tetra-chlor congeners are between 1.7 and 7 times higher the porous glass than for XAD-2 resin; values for penta-, hexa- and hepta-chloro congeners are very similar. The calculated “total” PCB (as the sum of individual congeners) was about four times higher for porous glass, because of the contribution from congeners with low chlorine numbers. Commercial mixtures may not reflect the real composition of PCB mixtures in the atmosphere.     

Extraction of Organic Compounds from Aqueous Media by Amberlite XAD Resins

Abstract

Three Amberlite polymeric resins, XAD-2, XAD-4 and XAD-7, were evaluated for extraction efficiency from aqueous media of several organic compounds representing pesticides, polyaromatic hydrocarbons, phenols and phthalate esters. The three resins exhibited different extraction characteristics. The extraction efficiency of the resins was found to be dependent on pH conditions and, on the average, was best at pH7. At this pH the XAD-2 and XAD-4 resins yielded quantitative recoveries in the 90–100% range for most compounds at the 20–200ppb level. Recoveries by XAD-7 resins were lower for several compounds. The recovery of aldrin and o, p DDT under all conditions was relatively low (>68%) and showed a higher degree of variability than that obtained for the other compounds. Alkaline pH conditions were generally unfavourable for the extraction of phenolic compounds but acidification to pH2 was not found to be a necessary step for the quantitative extraction of the phenolic compounds. Acidification to pH2 further led to a decrease in the recovery of most compounds for XAD-4 resins. A combined resin column yielded extraction efficiencies comparable to the XAD-2 column at pH 7, but since the three resins possess different extraction characteristics, a mixture comprising all three is recommended for the preconcentration of organic compounds from environmental water samples containing a wide range of compounds.     

Reversed-phase liquid chromatography analysis of alkyl-imidazolium ionic liquids II. Effects of different added salts and stationary phase influence

Two mixtures of four 1-alkyl-3-methylimidazolium ionic liquids (ILs) salts associated to the anions tetrafluoroborate or hexafluorophosphate were analyzed by reversed-phase liquid chromatography with three different stationary phases: Kromasil C(8), Zorbax Extend C(18) and Zorbax Sb-Aq. The effect on retention of various inorganic salts (NaCl, NaH(2)PO(4,) NaBF(4), NaClO(4) and NaPF(6)) added to acetonitrile/water mobile phases was studied. The three columns gave similar separation profiles. In all cases, the retention of ILs increased with the increasing affinity of the inorganic anions for the apolar stationary phases; a phenomenon called chaotropicity. The chaotropic anion order is Cl(-) approximately H(2)PO(4)(-) < BF(4)(-) approximately ClO(4)(-) < PF(6)(-). It is established that the presence of chaotropic anions in the mobile phase do not permit to differentiate between ILs associated to different anions. However, chloride or dihydrogenphosphate added salts do not fully screen the retention differences between ILs associated with different anions. Distorted and even split peaks may appear in the chromatogram depending on the nature and concentration of the injected ILs. In the RPLC analysis of imidazolium-based IL, it is recommended to add to the mobile phase significant amounts of a salt containing a chaotropic anion. This salt addition will improve the IL peak shapes and give reproducible retention factors. LODs in the low microgram range ( approximately 5 nmol) were obtained with the Kromasil C(8) column with a 50/50 acetonitrile-water mobile phase containing 0.01 M NaPF(6) added salt and 230 nm UV detection.     

A chromogenic macrocycle exhibiting cation-selective and anion-controlled color change: an approach to understanding structure-color relationships

[reaction: see text] A N-azo-coupled macrocycle (1) with a NO(2)S(2) donor set was synthesized as a chromoionophore and shown to exhibit Hg(2+) selectivity; anion control of the color of the Hg(2+) complex was observed. As a first approach, the nature of the color generation process was probed by determining the crystal structures of the two different colored species obtained with perchlorate and iodide anions. The results can be explained in terms of a "Push-n-Pull Process", which serves to illustrate how the coordinating ability of the anion controls the color change through formation of endo- or exo-metal complexes. The use of "simple" salts to induce color-switching of the above complex species was also reported.     

Selective preconcentration and determination of tributyltin in fresh water by electrothermal atomic absorption spectrometry

A rapid and simple method for separation and determination of tributyltin (TBT) in mineral and tap water is described. The procedure is based on the selective retention of TBT by a chelating resin, Amberlite XAD-2 impregnated with tropolone. The addition of 0.8% sulfuric acid to the water sample leads to the retention of TBT by the resin while monobutyltin (MBT), dibutyltin (DBT) and inorganic tin remain in solution. TBT is eluted with methyl isobutyl ketone (MIBK) obtaining a preconcentration factor of 80. Tin concentration is determined by ETAAS using zirconium coated tubes. Multi-injection and hot injection techniques are used in order to enhance the sensitivity of the method. A detection limit of 14.4 ng L(-1) is achieved with recoveries near to 100%. The procedure has been successfully applied to TBT determination in various fresh water samples.     

Preconcentration and determination of Ce, La and Pr by X-ray fluorescence analysis, using Amberlite XAD resins loaded with 8-Quinolinol and 2-(2-(5 chloropyridylazo)-5-dimethylamino)-phenol

8-Quinolinol (oxine) and 2-(2-(5 chloropyridylazo)-5-dimethylamino)-phenol (5ClDMPAP) were immobilized on the non ionic sorbents Amberlite XAD-4 and XAD-7. These loaded resins were used for the preconcentration of Ce, La and Pr. High preconcentration factors were obtained in each case. After the retention of these rare earths, the resins were measured as thin films by x-ray fluorescence spectrometry. Up to 50 ppm of REEs can be retained on these thin films.     

Trace detection of inorganic oxidants using desorption electrospray ionization (DESI) mass spectrometry

Desorption electrospray ionization (DESI), an established ambient ionization method in mass spectrometry (MS) for the analysis of organic compounds, is applied here to trace detection of inorganic salts, including inorganic oxidants. In-situ surface analysis of targeted compounds, including nitrogen-, halogen- and sulfur-salts, down to sub-nanogram levels, was performed using DESI-MS. Successful experiments were carried out in both the negative and the positive ion modes; simple anions and cations as well as small cluster ions were observed. Various surfaces are examined and surface porosity effects were briefly explored. Absolute detection limits on porous polytetrafluoroethylene (PTFE) of 120 pg (surface concentration 0.07 ng mm⁻²) and 50 pg (surface concentration 0.03 ng mm⁻²), were achieved for sodium chlorate and sodium perchlorate, respectively. The compounds of interest were examined in the presence of a hydrocarbon mixture to assess matrix effects: only a two- or three-fold decrease in the target ion intensity was observed. Commercial fireworks were analyzed to determine perchlorate salts in complex mixtures. This work demonstrates the potential applicability of ambient ionization mass spectrometry to forensic investigations involving improvised explosives.      

Modification of the electroosmotic flow and separation selectivity of anions in electrochromatography with pseudo-stationary phases of C14-alkyldimethylammoniopropane sulfonate zwitterionic surfactants by addition of salts to the background electrolyte

The effects of salts (NaCl, NaClO4, MgCl2, CeCl3) added to background electrolyte (BGE) solutions (10 mmol L(-1) sodium phosphate, pH 7.2) on electroosmotic flow (EOF) and the separation selectivity of anions (chloride, bromide, iodide, nitrite, nitrate, chlorate, thiocyanate, iodate, chromate, and molybdate ion) by capillary electrochromatography using the zwitterionic surfactant 3-(N,N-dimethylmyristylammonio)propane sulfonate (C14N3S) as a pseudo-stationary phase were investigated. There are two mechanisms affecting the separations: 1. the cations and anions of the added salts interact with the zwitterionic surfactant to varying degrees, thus changing the overall retention of the analytes; and 2. they change the EOF and the resulting apparent mobilities. It was shown that a BGE containing perchlorate and a low concentration of zwitterionic surfactant (2 mmol L(-1)) gave a stable and reproducible EOF and the concentration of perchlorate could be used to manipulate the separation selectivity for polarizable anions, such as iodide and thiocyanate. These effects are discussed in terms of measured association constants describing the interaction of anions and cations with the zwitterion.     

High loading polymer reagents based on polycationic Ultraresins. Polymer-supported reductions and oxidations with increased efficiency

Ultraresin 1 was prepared from highly branched polyethylene imine (M_n=10,000) via reductive cross-linking with terephthaldialdehyde. Following quaternization with methyl iodide, the polycationic Ultraresin 2, with iodide as a counterion, was obtained. These novel resins combine low swelling with high mechanical stability. By anion exchange polycationic Ultraresins carrying borohydride (3) and periodate (22) were generated and were investigated as very high loading polymer reagents. Ultra-borohydride resin 3 had a reducing activity of up to 12 mmol/g depending on the substrate. It proved successful in diverse reductions including those of aldehydes, ketones, and nitroolefines. The resin was employed in the reductive amination of aldehydes with an excess of amines, which were removed by the use of a scavenger resin. Periodate resin 22 was obtained with an active loading of up to 5.4 mmol/g and was employed in oxidations of sulfides, diols, hydroquinones, and hydrazines.     

Preconcentration of trace metals on Amberlite XAD-4 resin coated with dithiocarbamates and determination by inductively coupled plasma-atomic emission spectrometry in saline matrices

Preconcentration of Cd(II), Cu(II), Mn(II), Ni(II), Pb(II) and Zn(II) in saline matrices on Amberlite XAD-4 resins coated with ammonium pyrrolidine dithiocarbamate (APDC) and piperidine dithiocarbamate (pipDTC) and subsequent determination by inductively coupled plasma atomic emission spectrometry were studied. Parameters such as effect of pH, effect of HNO(3) concentration on elution of metals from resin were studied. The results show that Amberlite XAD-4 coated with APDC was more efficient in the recovery of metal ions compared with Amberlite XAD-4 coated with pipDTC, in the concentration range of 0.1-200 mug l(-1), for 1 g of Amberlite XAD-4 coated resin. The detection limits for Cd(II), Cu(II), Mn(II), Ni(II), Pb(II), Zn(II) are 0.1, 0.4, 0.3, 0.4, 0.6, 0.5 mug l(-1), respectively, for resin coated with APDC and 0.7, 1.0, 0.8, 0.9, 1.7 and 1.2 mug l(-1) for resin coated with pipDTC. The effect of diverse ions on the determination of aforesaid metals was studied. The method was applied for the determination of trace metal ions in artificial sea water and natural water samples. The results were compared with extraction AAS method.     

Determination of iodide in seawater samples by ion chromatography with chemically-bonded poly(ethylene glycol) stationary phase

An ion chromatographic method for the rapid and direct determination of iodide in seawater is reported. Poly(ethylene glycol) (PEG) groups were chemically bonded onto silica gel or C30-bonded silica gel via diol groups. PEG-bonded C30 binary phases allowed determination of iodide in seawater samples without any interference. Effects of eluent composition on retention behavior of inorganic anions have been investigated. Both cation and anion of the eluent affected the retention of analyte anions. The retention time of anions increased with increasing eluent concentration. The detection limit for iodide obtained by injecting 0.2 microl of sample was 13 microg l(-1) (S/N=3) while the limit of quantitation was 43 microg l(-1) (S/N=10). The present method was successfully applied to the rapid and direct determination of iodide in seawater with long-term durability.