3-(4-Tolylazo)phenylboronic acid as the active component of polyhydroxy compounds-selective electrodes

Ionophoric, extraction, acidic and hydrophobic properties of 3-(4-tolylazo)phenylboronic acid (TAPBA) were studied. Determined K_d value equals to 36±2, pK_a equals to 8.6±0.5. TAPBA extracts dobutamine from water into chloroform and transports it across a bulk chloroform membrane. The recovery is 83% (pH=7.5), the transport rate – (6.5±0.5)×10⁻⁷ mol/h. ¹H and ¹³C NMR data confirm the formation of an 1:1 complex between arylboronic acid and catecholamine. TAPBA was used as electrode-active component of plasticized membrane electrodes with cationic and anionic responses to catecholamines and phenolic acids, respectively. For the diethyl sebacate-plasticized membrane, a slope of electrode function to dobutamine is 56±2 mV/decade; the detection limit is 1.3×10⁻⁵ mol/l; the linear range – 5×10⁻⁵–1×10⁻² mol/l; the working pH-range – 4.8–7.6; the response time – 5–10 s. ISE gives incomplete cationic function to less lipophilic catecholamines. The membrane with cationic additive shows an anionic response to caffeic acid in wide pH range.     

A study of the spectrophotometric determination of traces of cadmium(II) and copper(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of polyglycol octylphenyl ether

A spectrophotometric study of the Cd(II) and Cu(II) complex of a new reagent, 2-(5-bromo-2-pyridylazo)-5-diethylamino phenol (5-Br-PADAP) in the presence of polyglycol octylphenyl ether (OP) is presented. A reddish binary complex is formed at pH 9 and shows maximal absorbance at 560 nm with molar absorptivity of 1.16 × 10⁵ · mol⁻¹ · cm⁻¹ liter (Cd), 1.5 × 10⁵ mol⁻¹ · cm⁻¹ · liter (Cu). Beer's law is followed over the range 0.0 to 20 μg cadmium(II) and 0.0–18 μg copper(II). The continuous variation method and molar ratio method showed that the metal ligand ratio is 1:2; ordinarily, most ions do not interfere with the determination and the method can be applied for direct spectrophotometric determination of cadmium(II) and copper(II) in actual samples and the results obtained are satisfactory.     

Crystal Structure and Thermal Decomposition of 5-Aminotetrazole Trinitrophloroglucinolate

5-Aminotetrazole trinitrophloroglucinolate ((ATZ)TNPG) was prepared and characterized by elemental analysis and FT-IR spectroscopy. The crystal structure was determined by X-ray diffraction analysis and it belonged to orthorhombic system and Pbca space group with a=0.6624(2) nm, b=1.7933(4) nm, c=2.3117(5) nm, V=2.7458(9) nm³, Z=4, and D_c=1.849 g·cm⁻³. The molecular formula was confirmed to be (ATZ)TNPG·2H₂O. 5-Aminotetrazole cation (ATZ⁺) and trinitrophloroglucinol anion (TNPG⁻) were linked into 2-D layers along b-axis and c-axis by hydrogen bonds. Then the layers were linked along a-axis by hydrogen bonds between the water molecules belonging to different layers. The thermal decomposition mechanism of the compound was studied by differential scanning calorimetry (DSC), thermogravimetry-thermogravimetric analysis (TG-DTG), and Fourier transform-infrared (FT-IR) spectroscopy techniques. Under nitrogen atmosphere with a heating rate of 10 °C·min⁻¹, the compound experienced one endothermic process with peak temperature of 76 °C and one exothermal process with peak temperature of 203 °C. The former was confirmed to be a dehydrate process. The latter was the decomposition of TNPG⁻ and ATZ⁺ in the compound. The exothermic enthalpy change of this process was −212.10 kJ·mol⁻¹. The kinetic parameter calculation from Kissinger's method were, E=132.1 kJ·mol⁻¹, ln(A/s⁻¹)=12.54 with r=0.9990, and the calculation results from Ozawa-Doyle's method were, E=133.1 kJ·mol⁻¹ with r=0.9992.     

Copper(II)-cetyltrimethylammonium chloride-chromal blue G ternary complex and its application to the spectrophotometric determination of copper(II)

A sensitive spectrophotometric method for the determination of copper(II) based on a ternary complex with chromal blue G, a triphenylmethane reagent in the presence of cetyltrimethylammonium chloride, is described. The sensitivity of color reaction between copper and chromal blue G has been greatly increased by the sensitizing action of cetyltrimethylammonium chloride, a cationic surfactant. The color development of the ternary complex can be utilized in the highly sensitive spectrophotometric determination of copper. The molar absorptivity of the binary complex between copper and chromal blue G ε_630nm = 9.56 × 10³liters · mol⁻¹ · cm⁻¹ is enchanced on ternary complex formation to ε_{542 nm} = 4.78 × 10⁴liters · mol⁻¹ · cm⁻¹. The ternary complex gave a maximal absorbance at 542 nm in the pH range 9.8–11. Beer's law is obeyed up to at least 1.2 ppm of copper. The maximal absorbance of the ternary complex was found to develop within 5 min and then it remains constant for several hours. The formation constant of the ternary complex is calculated to be 8.6 × 10¹⁰ under these conditions.     

[As(V)As(III)O6]: An uncommon anion group in the crystal structure of K2Cu3(As2O6)2

The crystal structure of K₂Cu₃(As₂O₆)₂ was determined from single-crystal X-ray data by a direct method strategy and Fourier summations [a = 10.359(4) Å, B = 5.388(2)Å, C = 11.234(4) Å, β = 110.48(2)°; space group C2/m; Z = 2; R_w = 0.025 for 1199 reflections up to sin /λ = 0.81 Å⁻¹]. In detail, the structure consists of As(V)O₄ tetrahedra and As(III)O₃ pyramids linked by a common O corner atom to [As(V)As(III)O₆]⁴⁻ groups with symmetry m. The bridging bonds As(V)---O [1.749(3) Å] and As(III)---O [1.838(2) Å] are definitely longer than the other As(V)---O bonds [mean 1.669 Å] and As(III)---O bonds [1.764(2) Å, 2×]. The angle As(V)---O---As(III) is 123.0(1)°. The Cu atoms are [4 + 2]- and [4 + 1]-, and the K atom is [9]-coordinated to oxygen atoms. The As₂O₆ groups and the Cu coordination polyhedra are linked to sheets parallel to (001). These sheets are connected by the K atoms. Single crystals of K₂Cu₃(As₂O₆)₂ suitable for X-ray work were synthesized under hydrothermal conditions.     

Sub- and post-micellar catalytic and inhibitory effects of cetlytrimethylammonium bromide in the permanganate oxidation of phenylalanine

The kinetics of phenylalanine (phe) oxidation by permanganate has been investigated in absence and presence of cetlytrimethylammonium bromide (CTAB) using conventional spectrophotometric technique. The rate shows first- and fractional-order dependence on [MnO₄⁻] and [phe] in presence of CTAB. At lower values of [CTAB] (≤10.0 × 10⁻⁴ mol dm⁻³), the catalytic ability of CTAB aggregates are strong. In contrast, at higher values of [CTAB] (≥10.0 × 10⁻⁴ mol dm⁻³), the inhibitory effect was observed in absence of H₂SO₄. We find that anions (Br⁻, Cl⁻ and NO₃⁻) in the form of sodium salts are strong inhibitors for the CTAB catalyzed oxidation. Kinetic and spectrophotometric evidences for the formation of an intermediate complex and an ion-pair complex between phe and MnO₄⁻, CTAB and MnO₄⁻, respectively, are presented. A mechanism consistent with kinetic results has been discussed. Complex formation constant (K_c) and micellar binding constant (K_s) were calculated at 30 °C and found to be K_c = 319 mol⁻¹ dm⁻³ and K_s = 1127 mol⁻¹ dm⁻³, respectively.     

Colorimetric determination of palladium (II) by means of promazine hydrochloride

In acetate buffer medium palladium(II) ions form with promazine hydrochloride (PM) two complexes: an orange one of a formula [Pd(C₁₇H₂₀N₂S)]²⁺ (λ_max = 460 nm, ε = 4.5 × 10³, at 20 °C and pH = 2) and a violet one of a formula [Pd(C₁₇H₂₀N₂S)₂]²⁺ (λ_max = 540 nm, ε = 8.8 × 10³ at 20 °C and pH = 2).The values for instability constants determined by Bjerrum's method amount to pK₁ = 3.95; pK₂ = 3.07; pβ₁ = 3.95; pβ₂ = 7.02, respectively.A colorimetric method of the determination of palladium(II) has been elaborated. The method consists in a measurement of the absorbance of the violet complex of palladium(II) with promazine hydrochloride at λ = 540 nm. The method permits the determination of 2–17 μg Pd/ml with an error of ±2%. The time of the determination is 20 min. Iron(III), Ce(IV), Pt(IV), V(V), Cr(VI), and HNO₃ interfere with the determination.     

Comparative studies on hydrolysis of bis(p-nitrophenyl) phosphate catalyzed by short- and long-alkyl-multiamine metallomicelles

Four short- and long-alkyl-multiamine ligands L¹–L⁴ have been synthesized and characterized. The catalytic efficiency of complex CuL¹ and functional metallomicelles CuL²–CuL⁴ were comparatively investigated for the hydrolysis of bis(p-nitrophenyl) phosphate (BNPP) in buffered solution at 30 °C. The ternary kinetic model for metallomicellar catalysis was suggested to analyze the experimental data. The kinetic and thermodynamic parameters k^′_N, K_T and pK_a were obtained. The results indicated that the complexes with 1:1 ratio of ligands L²–L⁴ to copper(II) ion were the kinetic active catalysts, and the deprotonized Cu(II) complex formed by activated water molecule was the real active species for BNPP catalytic hydrolysis. The real rate constant of the reaction catalyzed by CuL¹–CuL⁴ was 4.00 × 10⁻⁶, 7.44 × 10⁻⁵, 1.42 × 10⁻⁴ and 4.10 × 10⁻⁴ s⁻¹, respectively. The effects of ligand and microenvironment on the hydrolytic reaction of BNPP have been discussed in detail.     

Extraction and spectrophotometric determination of trace amounts of niobium with diphenylglioxal-bis-(2-hydroxybenzoylhydrazone)

A method is described for the direct spectrophotometric determination of microamounts of niobium based on its extraction into chloroform with dephenylglyoxal-bis-(2-hydroxy benzoyl) hydrazone (BSHB). This reagent builds up a chelate with Nb(V) in very acidic media, its chloroform solution being pink to reddish depending on niobium concentration (λ_max = 495 nm). Optimum conditions for chelate extraction and niobium determination have been established. The precision of procedure proposed, expressed in terms of relative standard deviation, is ±1.0%.It is shown that the method is sensitive, the molar absorptivity being 1.95 ± 0.02 × 10⁴ liter · mol⁻¹ · cm⁻¹ in the organic phase, and the interferences study demonstrates a high selectivity against common cations and the majority of those accompanying niobium in its natural sources and special alloys.     

Spectrophotometric microdetermination of iron(III) by tris-pyrrolidone(5)-hydroxamato(2)-chelate

The optimum conditions for the spectrophotometric determination of iron(III) with neutrial tris-PIH-chelate are: pH = 5, λ = 430 nm, PIH concentration 2 × 10⁻² M, and iron (III) concentration (0.6–3.3) × 10⁻⁴ M. Under these conditions the suggested method conforms to Beer's law and the molar absorptivity is 2800. The relative accuracy is ±0.48% based upon evaluation from the calibration curve and ±1.02% based upon algebraic equations. The precision is ±0.53% as deviation from the mean, and 0.69% as SD.The suggested method suffers from no interference from Fe²⁺, Al³⁺, Cr³⁺, Pb²⁺, Hg²⁺, Cd²⁺, Ni²⁺, Co²⁺, Zn²⁺, Mn²⁺, Ca²⁺, Sr²⁺, Ba²⁺, Mg²⁺, Ag⁺, F⁻, and tartrate, but interference is caused by U⁶⁺, V⁵⁺, Mo²⁺, Cu²⁺, (in larger concentrations) or by oxalate and citrate. The method may be used either as a sensitive spectrophotometric or visual method.     

Heat capacity, enthalpy and entropy of strontium niobate Sr2Nb2O7 and calcium niobate Ca2Nb2O7

The heat capacity and the enthalpy increments of strontium niobate Sr₂Nb₂O₇ and calcium niobate Ca₂Nb₂O₇ were measured by the relaxation time method (2–300 K), DSC (260–360 K) and drop calorimetry (720–1370 K). Temperature dependencies of the molar heat capacity in the form C_pm = 248.0 + 0.04350T − 3.948 × 10⁶/T² J K⁻¹ mol⁻¹ for Sr₂Nb₂O₇ and C_pm = 257.2 + 0.03621T − 4.434 × 10⁶/T² J K⁻¹ mol⁻¹ for Ca₂Nb₂O₇ were derived by the least-square method from the experimental data. The molar entropies at 298.15 K, S_m°(298.15 K) = 238.5 ± 1.3 J K⁻¹ mol⁻¹ for Sr₂Nb₂O₇ and S_m°(298.15 K) = 212.4 ± 1.2 J K⁻¹ mol⁻¹ for Ca₂Nb₂O₇, were evaluated from the low-temperature heat capacity measurements.     

Kinetics of the R + HBr RH + Br (CH3CHBr, CHBr2 or CDBr2) equilibrium. Thermochemistry of the CH3CHBr and CHBr2 radicals

The kinetics of the reaction of the CH₃CHBr, CHBr₂ or CDBr₂ radicals, R, with HBr have been investigated in a temperature-controlled tubular reactor coupled to a photoionization mass spectrometer. The CH₃CHBr (or CHBr₂ or CDBr₂) radical was produced homogeneously in the reactor by a pulsed 248 nm exciplex laser photolysis of CH₃CHBr₂ (or CHBr₃ or CDBr₃). The decay of R was monitored as a function of HBr concentration under pseudo-first-order conditions to determine the rate constants as a function of temperature. The reactions were studied separately from 253 to 344 K (CH₃CHBr + HBr) and from 288 to 477 K (CHBr₂ + HBr) and in these temperature ranges the rate constants determined were fitted to an Arrhenius expression (error limits stated are 1σ + Student’s t values, units in cm³ molecule⁻¹ s⁻¹, no error limits for the third reaction): k(CH₃CHBr + HBr) = (1.7 ± 1.2) × 10⁻¹³ exp[+ (5.1 ± 1.9) kJ mol⁻¹/RT], k(CHBr₂ + HBr) = (2.5 ± 1.2) × 10⁻¹³ exp[−(4.04 ± 1.14) kJ mol⁻¹/RT] and k(CDBr₂ + HBr) = 1.6 × 10⁻¹³ exp(−2.1 kJ mol⁻¹/RT). The energy barriers of the reverse reactions were taken from the literature. The enthalpy of formation values of the CH₃CHBr and CHBr₂ radicals and an experimental entropy value at 298 K for the CH₃CHBr radical were obtained using a second-law method. The result for the entropy value for the CH₃CHBr radical is 305 ± 9 J K⁻¹ mol⁻¹. The results for the enthalpy of formation values at 298 K are (in kJ mol⁻¹): 133.4 ± 3.4 (CH₃CHBr) and 199.1 ± 2.7 (CHBr₂), and for α-C–H bond dissociation energies of analogous compounds are (in kJ mol⁻¹): 415.0 ± 2.7 (CH₃CH₂Br) and 412.6 ± 2.7 (CH₂Br₂), respectively.     

Extraction-spectrophotometric determination of vanadium with 5,5′-dithiodisalicylhydroxamic acid (DTDSHA)

A new method for the extraction-spectrophotometric determination of V(V) is proposed. The violet complex V(V)-5,5′-dithiodisalicylhydroxamic acid formed in aqueous medium (pH 5.0) is extracted into a solution of trioctylmethylammonium chloride (Adogen 464) in toluene, and its spectrophotometric characteristics are studied. The stoichiometry of the complexes formed is 1:1 and 2:1 (reagent:vanadium), and 1:3 for the ionic association complex (2:1):trioctylmethylammonium ion. The system follows Beer's law at pH 5.0 (λ = 550 nm) over the concentration range 0.4 to 2.0 ppm (ε = 7.34 × 10³ liter · mol⁻¹ · cm⁻¹). The method is applied for the determination of vanadium in steel.     

Ruthenium-azoimine-chloranilates Synthesis,Spectra and Electrochemistry of Ruthenium(II)-1-alkyl-2-(arylazo)imidazole-chloranilate Complexes

Ag⁺-assisted dechlorination of blue cis-trans-cis Ru(R-aai-R′)₂Cl₂ followed by the reaction with chloranilic acid (H₂CA) in the presence of Et₃N, gives a neutral mononuclear violet complex [Ru(R-aai-R′)₂(CA)]. [R-aai-R′=p-R-C₆H₄—N=N—C₃H₂—NN, abbreviated as an N,N′ chelator where N(imidazole) and N(azo) represent N and N′, respectively; R = H (a), OMe (b), NO₂ (c) and R′= Me (4), Et(5), Bz(6)]. All the complexes exhibit strong intense MLCT transitions in the visible region and weak broad bands at higher wavelength (>700 nm). Visible transitions (580–595 nm) show a negative solvatochromic effect. The cyclic voltammograms show two quasireversible to irreversible couples positive to SCE and are due to CA⁻/CA²⁻ (1.2–1.35 V) and Ru(III)/Ru(II) (1.6–1.8 V) redox processes. Three couples, negative to SCE, are assigned to CA²⁻/CA³⁻ (−0.2 to −0.3 V), and azo reductions (−0.5 to −0.7, −0.8 to −0.9 V) of the chelated R-aai-R′.     

Spectrophotometric study of pseudopurpurin-Pd(II) dimer complex. Spectrophotometric determination of traces of Pd(II)

We have studied spectrophotometrically the Pseudopurpurin-Pd(II) complex in an ethanolic-water medium ¦Ethanolamine ¦_optimum = 4 × 10⁻¹M; λ = 670 nm; 20% H₂O; stable for at least 4 hr; ¦Reagent¦_optimum = 5 × 10⁻⁵M; stoichiometry 2:2; log K = 17.7. A new method for the spectrophotometric determination of Pd traces is proposed for concentrations between 0.30 and 2.40 ppm. The relative error and the interferences of the method have been investigated.     

A spectrophotometric study of the color reaction of zinc with 2,2′-dipyridyl-2-pyridylhydrazone (DPPH)

A spectrophotometric study of the zinc complex with 2,2′-clipyridyl-2-pyridylhydrazone (DPPH) is presented. The optimal formation conditions, the composition, and the overall apparent instability constant of the yellow, water-soluble zinc — DPPH complex are studied. A simple, rapid, and very sensitive spectrophotometric method for the determination of zinc with DPPH is proposed. At pH 10.9 to 12.4 the molecular extinction coefficient of the complex is 5.25 × 10⁴M⁻¹ · cm⁻¹ at 442 nm. DPPH can be also used as a methallochromic indicator for the complexometric titration of zinc.     

Glass–ceramic Li2S–P2S5 electrolytes prepared by a single step ball billing process and their application for all-solid-state lithium–ion batteries

We report that glass–ceramic Li₂S–P₂S₅ electrolytes can be prepared by a single step ball milling (SSBM) process. Mechanical ball milling of the xLi₂S·(100 − x)P₂S₅ system at 55 °C produced crystalline glass–ceramic materials exhibiting high Li-ion conductivity over 10⁻³ S cm⁻¹ at room temperature with a wide electrochemical stability window of 5 V. Silicon nanoparticles were evaluated as anode material in a solid-state Li battery employing the glass–ceramic electrolyte produced by the SSBM process and showed outstanding cycling stability.     

Dibenzophenoxazon-(5)-derivate als Neutralisationsindicatoren in wasserfreier Essigs?ure

Zusammenfassung Die relativen Basizitätskonstanten von 5H-Dibenzo(a,h)phenoxazon-(5) (I) (K=3,2 · 10^–2), 5H-Dibenzo(a,j)phenoxazon-(5) (II) (K=6,5 · 10^–2), 9-(N-1-Naphthylamino)-5H-dibenzo(a,j)phenoxazon-(5) (III) (K=1,12), 9-(N-2-Naphthylamino)-5H-dibenzo(a, j)phenoxazon-(S) (IV) (K=1,22), 9-Anilino-5H-dibenzo(a,j) phenoxazon-(5) (V) (K=1,28) und 9-(p-Tolylamino)-5H-dibenzo(a,j)phenoxazon-(5) (VI) (K=1,45) wurden für das Puffersystem Acetat-Antipyrinperchlorat in wasserfreier Essigsäure bestimmt. Die Verbindungen II, V und VI wurden zur visuellen Indikation von Titrationen schwacher Basen mit Perchlorsäure in wasserfreier Essigsäure benutzt. Mit Indicator II können Basen mit pK_a(H₂O)-Werten von 2–4 und mit den Indicatoren V und VI stärkere Basen mit pK_a(H₂O)-Werten von 4–7 bestimmt werden.

---

Dibenzophenoxazone-(5)-derivatives as neutralisation indicators in non-aqueous acetic acid

The relative basicity constants of 5H-dibenzo(a,h)phenoxazone-(5) (I) (K=3.2×10^–2), 5H-dibenzo(a,j)phenoxazone-(5) (II) (K=6.5×10^–2), 9-(N-1-naphthylamino)-5H-dibenzo(a,j)phenoxazone-(5) (III) (K=1.12), 9-(N-2-naphthylamino)-5H-dibenzo(a,j)phenoxazone-(5) (IV) (K=1.22), 9-anilino-5H-dibenzo(a,j)phenoxazone-(5) (V) (K=1.28) and 9-(p-tolylamino)-5H-dibenzo(a,j)phenoxazone-(5) (VI) (K=1.45) have been determined with respect to the buffer system antipyrine acetate-antipyrine perchlorate in non-aqueous acetic acid. The compounds II, V and VI were employed for visual indication of titrations of weak bases with perchloric acid in non-aqueous acetic acid. Indicator II is convenient for the titration of bases with pK _a (H₂O) values 2–4 and indicators V and VI for bases with pK_a(H₂O) values 4–7.

     

Isolation of p-tricyanovinylphenyldicyanomethide ion via a [2+2] cycloaddition of 7,7,8,8-tetracyanoquinodimethane (TCNQ) molecules

In the presence of CoCl₂·6H₂O and dppm (bis(diphenylphosphino) methane), the reaction of TCNQ (7,7,8,8-tetracyanoquinodimethane) molecules by [2+2] cycloaddition forms a p-tricyanovinylphenyldicyanomethide ion (PCQ⁻), which has been obtained as one anion unit in one new compound [Co(dppmdo)₃][PCQ⁻]₂·H₂O 1 (dppmdo = bis(diphylphospine oxide) methane). Its structure was determined by X-ray crystallography: 1 crystallizes in with a = 14.174(3) Å, b = 19.553(4) Å, c = 19.776(4) Å, α = 112.72(3)°, β = 95.43(3)°, γ = 110.79(3)°, and Z = 2. It was characterized by IR spectra, UV–Vis spectra, and cyclic voltammogram. Magnetic properties indicate that no magnetic coupling between PCQ⁻ and [Co(dppmdo)₃]²⁺ unit.     

The standard partial molar entropy of the aqueous tetra-n-butylammonium cation

The standard partial molar entropy of the aqueous tetrabutylammonium cation, not known previously, has now been obtained, based on the molar entropy of two of its crystalline salts, the iodide and the tetraphenylborate, recently determined experimentally for this purpose. The calculation required also published molar enthalpies of solution and solubilities of these two salts as well as of the perchlorate. The choice of the anions depended mainly on the limited solubilities of the examined salts in water, facilitating the estimation of the relevant activity coefficients. The result is S^∞(Bu₄N⁺, aq) = (380 ± 20) J · K⁻¹ · mol⁻¹ at T = 298.15 K, on the mol · dm⁻³ scale and based on S^∞(H⁺, aq) = (−22.2 ± 1.2) J · K⁻¹ · mol⁻¹ (yielding the ‘absolute’ value). The molar entropy of this cation in the ideal gas standard state, S(Bu₄N⁺, g) = (798 ± 8) J · K⁻¹ · mol⁻¹ then yielded the molar entropy of hydration Δ_hydS^∞ (Bu₄N⁺) = (−418 ± 23) J · K⁻¹ · mol⁻¹.