Impact of polypyrrole incorporation on nickel oxide@multi walled carbon nanotube composite for application in supercapacitors

In this article we report the synthesis of polypyrrole incorporated nickel oxide multi walled carbon nanotube (NiO@NMWCNT/PPy) composites by thermal reduction protocol for supercapacitor applications. The structural and morphological properties of the composites were confirmed by the aid of X-ray diffraction (XRD), Field-emission scanning electron microscope (FE-SEM) with energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS) and Field-emission transmission electron microscopy (FE-TEM) analysis indicating the hexagonal crystal structure of NiO decorated on NMWCNT/Ppy. The electrochemical characteristics of the NiO@MWCNT/PPy composite were analyzed in the presence of 2 M KOH as an electrolyte. The NiO@NMWCNT/PPy nanostructured composite produced a plenty of active sites for ion migration reactions that facilitate the energy storage mechanism. As a proof of concept demonstration, the NiO@NMWCNT/PPy composite was explored as an electrode materials in supercapacitor and exhibited specific capacitance of 395 F g⁻¹ and cyclic stability up to 5000 cycles at 0.5 A g⁻¹. Enhanced performance of composite is attributed to the incorporation of polypyrrole in NiO@NMWCNT. The improved capacitance and cyclic stability demonstrated by the composite indicates the NiO@NMWCNT/PPy to be a promising candidate for supercapacitor applications.     

Effect of Lithia and Substrate on the Electrochemical Performance of a Lithia/Cobalt Oxide Composite Thin‐Film Anode

Highly porous reticular Li₂O/CoO composite thin films fabricated by electrostatic spray deposition were investigated by using X-ray diffraction, scanning electron microscopy, galvanostatic cell-cycling measurements, and AC impedance spectroscopy measurements. The results of the electrochemical tests indicate that the initial coulombic efficiency and capacity retention are dependent on Li₂O content and the specific surface area of the deposited layer. Irrespective of the type of substrate, the electrode gave the best electrochemical performance when the molar ratio of Li to Co was controlled at 1:1. At the optimal composition, at 0.2 C the initial coulombic efficiency was as high as 81.9 % and 83.6 % for the film on Cu foil and on porous Ni, respectively. The Li₂O/CoO (Li/Co=1:1) films on Ni foam and Cu foil had sustained capacities of up to 790 and 715 mAh g⁻¹, respectively, at a rate of 1 C over 100 cycles at 25 °C. Similar cycling experiments carried out at 70 °C showed that the capacity is temperature-sensitive, and it exhibited reversible capacities as high as 1018 (Cu foil) and 1269 mAh g⁻¹ (Ni foam) for up to 100 cycles. The thin-film electrodes on Ni foam always performed better than those on Cu foil. Cycling at elevated temperature (70 °C) also resulted in a significant increase in capacity.     

Enhanced Supercapacitor Performance Using a Co3O4@Co3S4 Nanocomposite on Reduced Graphene Oxide/Ni Foam Electrodes

To avoid an enormous energy crisis in the not-too-distant future, it be emergent to establish high-performance energy storage devices such as supercapacitors. For this purpose, a three-dimensional (3D) heterostructure of Co₃O₄ and Co₃S₄ on nickel foam (NF) that is covered by reduced graphene oxide (rGO) has been prepared by following a facile multistep method. At first, rGO nanosheets are deposited on NF under mild hydrothermal conditions to increase the surface area. Subsequently, nanowalls of cobalt oxide are electro-deposited on rGO/Ni foam by applying cyclic-voltammetry (CV) under optimized conditions. Finally, for the synthesis of Co₃O₄@Co₃S₄ nanocomposite, the nanostructure of Co₃S₄ was fabricated from Co₃O₄ nanowalls on rGO/NF by following an ordinary hydrothermal process through the sulfurization for the electrochemical application. The samples are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The obtained sample delivers a high capacitance of 13.34 F cm⁻² (5651.24 F g⁻¹) at a current density of 6 mA cm⁻² compared to the Co₃O₄/rGO/NF electrode with a capacitance of 3.06 F cm⁻² (1230.77 F g⁻¹) at the same current density. The proposed electrode illustrates the superior electrochemical performance such as excellent specific energy density of 85.68 W h Kg⁻¹, specific power density of 6048.03 W kg⁻¹ and a superior cycling performance (86% after 1000 charge/discharge cycles at a scan rate of 5 mV s⁻¹). Finally, by using Co₃O₄ @Co₃S₄/rGO/NF and the activated carbon-based electrode as positive and negative electrodes, respectively, an asymmetric supercapacitor (ASC) device was assembled. The fabricated ASC provides an appropriate specific capacitance of 79.15 mF cm⁻² at the applied current density of 1 mA cm⁻², and delivered an energy density of 0.143 Wh kg⁻¹ at the power density of 5.42 W kg⁻¹.     

In situ polymerization and reduction to fabricate gold nanoparticle‐incorporated polyaniline as supercapacitor electrode materials

Nanocomposites of gold nanoparticles and polyaniline are synthesized by using HAuCl₄ and ammonium peroxydisulfate as the co‐oxidant involving in situ polymerization of aniline and in situ reduction of HAuCl₄. Through these in situ methods, the synthesized Au nanoparticles of ca. 20 nm embedded tightly and dispersed uniformly in polyaniline backbone. With the Au content in composite increasing from 4.20 to 24.72 wt.%, the specific capacitance of the materials first increased from 334 to 392 F g⁻¹ and then decreased to 298 F g⁻¹. Based on the real content of PANI in composite material, the highest specific capacitance is calculated to be 485 F g⁻¹ at the Au amount of 19.15 wt.%, which remains 55.6% after 5000 cycles at the current density of 2 A g⁻¹. Finally, the asymmetric supercapacitor of AuNP/PANI||AC and the symmetric supercapacitor of AuNP/PANI||AuNP/PANI are assembled. The asymmetric supercapacitor device shows a better electrochemical performance, which delivers the maximum energy density of 7.71 Wh kg⁻¹ with power density of 125 W kg⁻¹ and maximum power density of 2500 W kg⁻¹ with the energy density of 5.35 Wh kg⁻¹.     

Fabrication of a Hierarchical Ni(OH)2@Ni3S2/Ni Foam Electrode from a Prussian Blue Analogue-Based Composite with Enhanced Electrochemical Capacitive and Electrocatalytic Properties

Developing high-efficiency, cost-effective, and durable electrodes is significant for electrochemical capacitors and electrocatalysis. Herein, a 3D bifunctional electrode consisting of nickel hydroxide nanosheets@nickel sulfide nanocubes arrays on Ni foam (Ni(OH)₂@Ni₃S₂/NF) obtained from a Prussian blue analogue-based precursor is reported. The 3D higher-order porous structure and synergistic effect of different compositions endow the electrode with large specific surface area, facile ion/electron transport path, and improved conductivity. As a result, the Ni(OH)₂@Ni₃S₂/NF electrode exhibits a high specific capacity of 211 mA h g⁻¹ at a current density of 1 A g⁻¹ and 73 % capacity retention after 5000 cycles at 5 A g⁻¹. Moreover, the Ni(OH)₂@Ni₃S₂/NF electrode has superior electrocatalytic activity for the hydrogen evolution reaction with low overpotentials of 140 and 210 mV at current densities of 10 and 100 mA cm⁻², respectively. The synthetic strategy for the unique higher-order porous structure can be extended to fabricate other composite materials for energy storage and conversion.     

Preparation of hexagonal nanoporous nickel hydroxide film and its application for electrochemical capacitor

Nanoporous nickel hydroxide film has been successfully electrodeposited on titanium substrate from nickel nitrate dissolved in the aqueous domains of the hexagonal lyotropic liquid crystalline phase of Brij 56. Low-angle X-ray diffraction (XRD), transmission electron microscopy (TEM), and atomic force microscopy (AFM) studies show that the film has a regular nanostructure consisting of a hexagonal array of cylindrical pores with a repeat center-to-center spacing of about 7 nm. Preliminary electrochemical studies are carried out using cyclic voltammetry (CV) and chronopotentiometry technology. A maximum specific capacitance of 578 F g⁻¹ could be achieved for the nanoporous Ni(OH)₂ film electrode, suggesting its potential application in electrochemical capacitors.     

Recent Advances on Nitrogen-Doped Porous Carbons Towards Electrochemical Supercapacitor Applications

Due to ever-increasing global energy demands and dwindling resources, there is a growing need to develop materials that can fulfil the World's pressing energy requirements. Electrochemical energy storage devices have gained significant interest due to their exceptional storage properties, where the electrode material is a crucial determinant of device performance. Hence, it is essential to develop 3-D hierarchical materials at low cost with precisely controlled porosity and composition to achieve high energy storage capabilities. After presenting the brief updates on porous carbons (PCs), then this review will focus on the nitrogen (N) doped porous carbon materials (NPC) for electrochemical supercapacitors as the NPCs play a vital role in supercapacitor applications in the field of energy storage. Therefore, this review highlights recent advances in NPCs, including developments in the synthesis of NPCs that have created new methods for controlling their morphology, composition, and pore structure, which can significantly enhance their electrochemical performance. The investigated N-doped materials a wide range of specific surface areas, ranging from 181.5 to 3709 m² g⁻¹, signifies a substantial increase in the available electrochemically active surface area, which is crucial for efficient energy storage. Moreover, these materials display notable specific capacitance values, ranging from 58.7 to 754.4 F g⁻¹, highlighting their remarkable capability to effectively store electrical energy. The outstanding electrochemical performance of these materials is attributed to the synergy between heteroatoms, particularly N, and the carbon framework in N-doped porous carbons. This synergy brings about several beneficial effects including, enhanced pseudo-capacitance, improved electrical conductivity, and increased electrochemically active surface area. As a result, these materials emerge as promising candidates for high-performance supercapacitor electrodes. The challenges and outlook in NPCs for supercapacitor applications are also presented. Overall, this review will provide valuable insights for researchers in electrochemical energy storage and offers a basis for fabricating highly effective and feasible supercapacitor electrodes.     

Facile synthesis of nickel cobalt sulfide nano flowers for high performance supercapacitor applications

A facile synthesis of nickel cobalt sulfide (NCS) nanoflowers have been deposited successfully onto binder free 3D nickel foam electrodes using simple successive ionic layer adsorption and reaction (SILAR) method for supercapacitor applications. The obtained NCS nanoflowers manifest ultrahigh specific capacitance of 1899 F g^?1 at a scan rate of 5 mV s^?1. The NCS nanoflowers exhibit a prominent energy density of 55.16 Wh kg^?1 at power density of 495 W kg^?1 and superior cyclic stability of 94% after 10000 cycles. In addition, the asymmetric supercapacitor (ASC) device is fabricated using NCS nanoflower as positive and reduced graphene oxide (rGO) as negative electrodes, respectively. The ASC (NCS//rGO) delivered good capacity with excellent energy and power densities within 1.6 V wider potential window. Hence, NCS nanoflowers are an outstanding material for energy storage applications in near future.     

A facile synthesis of hierarchical porous carbon derived from renewable lignin for high-performance supercapacitor

In this work, we proposed a facile one-pot pyrolysis method to conveniently manufacture lignin-derived carbon materials with graded porous construction for use in supercapacitors. The renewable lignin was selected as precursor, while the potassium citrate was used as a pore-forming agent. The properties of the prepared lignin-derived carbon (LAC) and the performance for supercapacitor application were thoroughly evaluated. The LAC at optimal preparation conditions shows a layered porous structure with a large specific surface area of 3174 cm² g⁻¹ and pore volume of 2.796 cm³ g⁻¹, where the specific capacitance reach to 241 F g⁻¹ at 1 A g⁻¹ scan rate in 6 M KOH electrolyte solution. At the same time, the specific capacitance remains at 220 F g⁻¹ even at an excessive scan velocity of 20 A g⁻¹, while the capacitance retention is still close to 91.3%. The capacitance retention rate is stable above 95% after 10,000 charge/discharge cycles, which shows the desired long-time stability. All these results demonstrate the outstanding properties of the new prepared LAC material and the considerable application potential in the field of electrical energy storage.     

Binder-free porous core–shell structured Ni/NiO configuration for application of high performance lithium ion batteries

An interwoven core–shell structured Ni/NiO anode for lithium ion batteries was created by a simple oxidation of Ni foam. As-prepared configuration has a high specific discharge capacity of 701 mAh g^?1 at the 2nd cycle. Its electrochemical performance at subsequent cycles shows good energy capacity of 646 mAh g^?1 at the 65th cycle as well as good rate capability. The porous core–shell structure not only buffers the volume change during cycling but also effectively increases the contact among anode, current collector and electrolyte. The small contact resistance between NiO and Ni facilitates enhanced intrinsic kinetics from conversion reaction.     

Ni Foam-Supported Tin Oxide Nanowall Array: An Integrated Supercapacitor Anode

A novel product consisting of a homogeneous tin oxide nanowall array with abundant oxygen deficiencies and partial Ni-Sn alloying onto a Ni foam substrate was successfully prepared using a facile solvothermal synthesis process with subsequent thermal treatment in a reductive atmosphere. Such a product could be directly used as integrated anodes for supercapacitors, which showed outstanding electrochemical properties with a maximum specific capacitance of 31.50 mAh·g⁻¹ at 0.1 A·g⁻¹, as well as good cycling performance, with a 1.35-fold increase in capacitance after 10,000 cycles. An asymmetric supercapacitor composed of the obtained product as the anode and activated carbon as the cathode was shown to achieve a high potential window of 1.4 V. The excellent electrochemical performance of the obtained product is mainly ascribed to the hierarchical structure provided by the integrated, vertically grown nanowall array on 3D Ni foam, the existence of oxygen deficiency and the formation of Ni-Sn alloys in the nanostructures. This work provides a general strategy for preparing other high-performance metal oxide electrodes for electrochemical applications.     

Application of a novel redox-active electrolyte in MnO2-based supercapacitors

This paper reports a novel strategy for preparing redox-active electrolyte through introducing a redox-mediator(p-phenylenediamine,PPD) into KOH electrolyte for the application of ball-milled MnO 2-based supercapacitors.The morphology and compositions of ball-milled MnO 2 were characterized using scanning electron microscopy(SEM) and X-ray diffraction(XRD).The electrochemical properties of the supercapacitor were evaluated by cyclic voltammetry(CV),galvanostatic charge-discharge(GCD),and electrochemical impedance spectroscopy(EIS) techniques.The introduction of p-phenylenediamine significantly improves the performance of the supercapacitor.The electrode specific capacitance of the supercapacitor is 325.24 F g-1,increased by 6.25 folds compared with that of the unmodified system(44.87 F g-1) at the same current density,and the energy density has nearly a 10-fold increase,reaching 10.12 Wh Kg-1.In addition,the supercapacitor exhibits good cycle-life stability.     

Facile ordered ZnCo2O4@MnO2 nanosheet arrays for superior-performance supercapacitor electrode

Constructing ZnCo₂O₄ nanosheet arrays (NSAs)@MnO₂ nanosheets core-shell nanostructures directly on the current collector (Ni foam) was successfully realized via hydrothermal process and heat treatment. The whole surfaces of uniform ZnCo₂O₄ NSAs were covered with well-ordered MnO₂ nanosheets, which make the whole system have a large specific surface area. At a low current density of 2 mA cm⁻², supercapacitor electrode made of ZnCo₂O₄@MnO₂ composite gave rise to a superior specific capacity about 929.2 C g⁻¹. Although at an ultrahigh current density of 40 mA cm⁻², it still kept a satisfactory specific capacity about 751.1 C g⁻¹, and retained ∼95.75% of the capacity even after 5000 cycles. Because of the synergistic effect between ZnCo₂O₄ and MnO₂ and the great surface area of the system with the special core-shell structure, ZnCo₂O₄@MnO₂ composite has the excellent rate performance, considerable capacity, and quite good cycle performance, which make it a candidate for a new generation of superior-performance electrochemical supercapacitors.     

Hierarchical FeCo2S4@FeNi2S4 Core/Shell Nanostructures on Ni Foam for High-Performance Supercapacitors

The design of electrode materials with rational core/shell structures is promising for improving the electrochemical properties of supercapacitors. Hence, hierarchical FeCo₂S₄@FeNi₂S₄ core/shell nanostructures on Ni foam were fabricated by a simple hydrothermal method. Owing to their structure and synergistic effect, they deliver an excellent specific capacitance of 2393 F g⁻¹ at 1 A g⁻¹ and long cycle lifespan as positive electrode materials. An asymmetric supercapacitor device with FeCo₂S₄@FeNi₂S₄ as positive electrode and graphene as negative electrode exhibited a specific capacitance of 133.2 F g⁻¹ at 1 A g⁻¹ and a high energy density of 47.37 W h kg⁻¹ at a power density of 800 W kg⁻¹. Moreover, the device showed remarkable cycling stability with 87.0 % specific-capacitance retention after 5000 cycles at 2 A g⁻¹. These results demonstrate that the hierarchical FeCo₂S₄@FeNi₂S₄ core/shell structures have great potential in the field of electrochemical energy storage.     

PPy modified titanium foam electrode with high performance for supercapacitor

Pyrrole was polymerized on the surface of titanium foam using FeCl₃ as oxidant and the as-synthesized product could be directly used as electrode for supercapacitor. The globular polypyrrole (PPy) particles were firmly loaded on the substrate with high density. The morphology study of PPy film is observed in SEM images, the XRD, FTIR and UV–vis spectra reveal the structure and crystalline of PPy nanoparticles. The electrochemical properties of PPy modified electrode are investigated by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) and cycle life techniques. The electrochemical measurements showed such a PPy–Ti electrode had a wide working potential window, a high specific capacitance of 855 F g⁻¹ and excellent cycle stability at a discharge current density of 1 A g⁻¹.     

Intertwined Titanium Carbide MXene within a 3 D Tangled Polypyrrole Nanowires Matrix for Enhanced Supercapacitor Performances

The exploration of the rational design and synthesis of unique and robust architectured electrodes for the high capacitance, rate capability, and stability of supercapacitors is crucial to the future of energy storage technology. Herein, an in situ synthesis of multilayered titanium carbide MXene tightly caging within a 3 D conducting tangled polypyrrole (PPy) nanowire (NW) network is proposed as an effective strategy to prevent the aggregation of MXene, profoundly enhancing the electrochemical performance of the supercapacitor. Owing to the beneficial effects of an ideal 3 D interconnected porous structure and high electrical conductivity, the obtained electrode exhibits fast charge and ion transport kinetics as well as full usage of active material. As expected, the 3 D Ti₃C₂T_x@PPY NW exhibits a specific capacitance five times higher than that of pristine MXene (610 F g⁻¹), a good rate capability up to a current density of 25 A g⁻¹, and excellent stability with 100 % retention after 14 000 cycles at 4 A g⁻¹, outperforming the known state-of-the-art MXene-based supercapacitor. Our work provides a facile method for enhancing the performance of MXene-based energy storage devices.     

Electrochemical Evaluation of Titanium (IV) Oxide/Polyacrylonitrile Electrospun Discharged Battery Coals as Supercapacitor Electrodes

The TiO₂ nanoparticles are electrospun with polyacrylonitrile (PAN) polymer solution onto the discharged battery coal (DBC) electrode and the results are evaluated as a supercapacitor. The morphology and chemical composition of the synthesized TiO₂ nanoparticles and PAN+TiO₂ nanocomposite fibers were characterized by Scanning electron microscopy, thermogravimetry and FTIR analysis. Supercapacitor measurements and electrochemical characterizations of the electrodes examined by cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical measurements showed that the best current value was obtained from PAN and TiO₂ coated DBC. The performances of both PAN and PAN+TiO₂ coated DBC electrodes were investigated as supercapacitors. PAN+TiO₂/DBC showed the best specific capacitance value of 156.00 F g⁻¹ and PAN/DBC showed 74.93 F g⁻¹. In addition, PAN+TiO₂/DBC exhibited reliable stability performance over 2000.00 cycles.     

Insoluble metal hexacyanoferrates as supercapacitor electrodes

Nano-sized insoluble iron, cobalt and nickel hexacyanoferrates (Mhcf) were prepared by a simple co-precipitation method. The potential of using these materials for supercapacitor was examined by cyclic voltammogram and constant charge/discharge. Due to the different types of the second metal (M), the Mhcf electrodes showed different electrochemical capacitive performances. The specific discharge capacitances of Fehcf, Nihcf and Cohcf electrodes at the current density of 0.2 A g⁻¹ were 425 F g⁻¹, 574.7 F g⁻¹ and 261.56 F g⁻¹, respectively. Meanwhile, the Mhcf electrodes showed good cyclic performance.     

Rational Design of Porous Structured Nickel Manganese Sulfides Hexagonal Sheets-in-Cage Structures as an Advanced Electrode Material for High-Performance Electrochemical Capacitors

The design of hierarchical electrodes comprising multiple components with a high electrical conductivity and a large specific surface area has been recognized as a feasible strategy to remarkably boost pseudocapacitors. Herein, we delineate hexagonal sheets-in-cage shaped nickel–manganese sulfides (Ni-Mn-S) with nanosized open spaces for supercapacitor applications to realize faster redox reactions and a lower charge-transfer resistance with a markedly enhanced specific capacitance. The hybrid was facilely prepared through a two-step hydrothermal method. Benefiting from the synergistic effect between Ni and Mn active sites with the improvement of both ionic and electric conductivity, the resulting Ni-Mn-S hybrid displays a high specific capacitance of 1664 F g⁻¹ at a current density of 1 A g⁻¹ and a capacitance of 785 F g⁻¹ is maintained at a current density of 50 A g⁻¹, revealing an outstanding capacity and rate performance. The asymmetric supercapacitor device assembled with the Ni-Mn-S hexagonal sheets-in-cage as the positive electrode delivers a maximum energy density of 40.4 Wh kg⁻¹ at a power density of 750 W kg⁻¹. Impressively, the cycling retention of the as-fabricated device after 10 000 cycles at a current density of 10 A g⁻¹ reaches 85.5 %. Thus, this hybrid with superior capacitive performance holds great potential as an effective charge-storage material.     

Sulfur-/Nitrogen-Rich Albumen Derived “Self-Doping” Graphene for Sodium-Ion Storage

The development of sodium-ion batteries (SIBs) is hindered by the rapid reduction in reversible capacity of carbon-based anode materials. Outside-in doping of carbon-based anodes has been extensively explored. Nickel and NiS₂ particles embedded in nitrogen and sulfur codoped porous graphene can significantly improve the electrochemical performance. Herein a built-in heteroatom “self-doping” of albumen-derived graphene for sodium storage is reported. The built-in sulfur and nitrogen in albumen act as the doping source during the carbonization of proteins. The sulfur-rich proteins in albumen can also guide the doping and nucleation of nickel sulfide nanoparticles. Additionally, the porous architecture of the carbonized proteins is achieved through removable KCl/NaCl salts (medium) under high-temperature melting conditions. During the carbonization process, nitrogen can also reduce the carbonization temperature of thermally stable carbon materials. In this work, the NS-graphene delivered a specific capacity of 108.3 mAh g⁻¹ after 800 cycles under a constant current density of 500 mA g⁻¹. In contrast, the Ni/NiS₂/NS-graphene maintained a specific capacity of 134.4 mAh g⁻¹; thus the presence of Ni/NiS₂ particles improved the electrochemical performance of the whole composite.