TiO2/柚子皮生物质活性炭复合材料的制备和吸附光降解性研究

本文以自制柚子皮生物质活性炭为原料,采用凝胶-溶胶法合成TiO2/柚子皮生物质活性炭复合材料(TiO2/BAC)。对复合材料进行SEM、FTIR、XRD等表征,并研究该复合材料对中性红、亚甲基蓝染料及甲醛的吸附降解性能。结果表明,在复合材料中柚子皮生物质活性炭的添加量为7 g、预吸附时间为2 h时,对染料具有最佳的吸附降解效果,复合材料在循环使用5次后对染料的吸附降解率仍达到了80 %以上。当活性炭的添加量为6 g、复合材料的添加量为2 g时,复合材料对甲醛的吸附降解达到最大,可达61%。表明该复合材料对中性红、亚甲基蓝染料及甲醛具有良好的吸附降解效果,有望用于废水染料的去除和家居甲醛净化。     

Ag@ Fe-TiO2 catalysts for catalytic oxidation of formaldehyde indoor: a further improvement of Fe-TiO2

In this paper, a series of Fe-doped TiO₂ (Fe-TiO₂) catalysts were prepared by ultrasonic hydrothermal method and were used to catalytic oxidation formaldehyde (HCHO) indoor at room temperature. Although the catalytic activity was improved compared with P25, but the final concentration of HCHO was still higher than the Chinese standard (GB 0.08 mg/m³), and the stability was restrict under room temperature. In order to improve the catalytic activity and stability of the catalysts, various concentrations of Ag were loaded on Fe-TiO₂, and good catalytic oxidation effect was obtained and had a good repeat catalytic effect under room condition. UV–Vis, IR, PL, XRD, SEM, BET, XPS were used to characterize the materials. The results showed that the higher dispersion of active Ag, and the synergistic effect between Ag, Fe and TiO₂ nanostructure were helpful to improve the catalytic oxidation ability of Ag@Fe-TiO₂. In the repeat experiments, 0.6%Ag@0.3%Fe-TiO₂ exhibited good catalytic activity and stability. The formaldehyde concentration was reduced to 0.05 mg/m³, after four rounds of tests, the formaldehyde concentration was still below 0.08 mg/m³, applying for long time indoor HCHO degradation at room temperature. Indicating the modification of Ag element can further promote the catalytic activity and stability of Fe-TiO₂.

     

Mixed phase Fe2O3/Mn3O4 magnetic nanocomposite for enhanced adsorption of methyl orange dye: Neural network modeling and response surface methodology optimization

In this research, a novel magnetic mesoporous adsorbent with mixed phase of Fe₂O₃/Mn₃O₄ nanocomposite was prepared by a facile precipitating method and characterized extensively. The prepared nanocomposite was used as adsorbent for toxic methyl orange (MO) dye removal from aqua matrix considering its high surface area (178.27 m²/g) with high saturation magnetization (23.07 emu/g). Maximum dye adsorption occurs at solution pH 2.0 and the electrostatic attraction between anionic form of MO dye molecules and the positively charged nanocomposite surface is the main driving force behind this adsorption. Response surface methodology (RSM) was used for optimizing the process variables and maximum MO removal of 97.67% is obtained at optimum experimental condition with contact time, adsorbent dose and initial MO dye concentration of 45 min, 0.87 g/l and 116 mg/l, respectively. Artificial neural network (ANN) model with optimum topology of 3–5–1 was developed for predicting the MO removal (%), which has shown higher predictive ability than RSM model. Maximum adsorption capacity of this nanocomposite was found to be 322.58 mg/g from Langmuir isotherm model. Kinetic studies reveal the applicability of second‐order kinetic model with contribution of intra‐particle diffusion in this process.     

Converting red mud wastes into mesoporous ZSM-5 decorated with TiO2 as an eco-friendly and efficient adsorbent-photocatalyst for dyes removal

Red mud wastes have been converted into mesoporous zeolite socony mobile-5 (ZSM-5) followed by deposited titanium dioxide (TiO₂) nanoparticles to generate synergy adsorption-photodegradation for removal of dye removal in waste water. The amount of TiO₂ loading was varied to achieve optimum photocatalytic activity while maintaining the mesoporosity and high surface area of ZSM-5. Sol-gel method facilitated the formation of anatase TiO₂ on the ZSM-5. The fourier transform infrared spectra clarified the formation of Si–O–Ti at 957 cm^?1 by the exchanging the hydrogen ion with titanium ion, which proved by decreasing the absorption band of Si–OH and Si–O interaction at 964 and 944 cm^?1, respectively. Sol-gel method also preserved the mesopore diameter of ZSM-5 at 3.5 nm which allow the diffusion of methylene blue (MB) molecules into the pores. However, the surface area and the pore volume were slightly reduced with increasing the TiO₂ loading. The adsorption performance of samples showed that the increasing in the TiO₂ loading led to the decreasing in the adsorption capacity. All samples showed the suitability towards the pseudo second order kinetic. The Langmuir isotherm was suitable to describe the adsorption mechanism by monolayer adsorption. Mesoporosity of ZSM-5 accelerated the adsorption of dye via the increase of mass transfer in the pore channel which confirmed by the low intercept of intraparticle diffusion model at the first stage. The photocatalytic test showed that 10% TiO₂ loading on the ZSM-5 exhibited the highest methylene blue removal followed by 5% and 20% TiO₂ loading. Optimization on the amount of photocatalyst and the pH of solution indicated the reaction favoured 1 g L^?1 of catalysts and at alkaline pH. 10% TiO₂/ZSM-5 also exhibited high stability and reusability up to four reaction cycles. Photocatalytic performance of 10% TiO₂/ZSM-5 was further investigated on photodegradation of malachite green and rhodamine B organic dyes, which showed the photocatalytic efficiency of 73 and 88%, respectively. Superoxide radical, hydroxyl radical, and photogenerated electron were identified as the main active species for MB photodegradation based on the reduction of degradation rate following the addition scavenger molecules.     

A novel approach for the synthesis of visible-light-active nanocrystalline N-doped TiO2 photocatalytic hydrosol

A visible-light-active nitrogen doped nanocrystalline titanium dioxide (N–TiO₂) hydrosol was prepared by precipitation–peptization method and following with hydrothermal crystallization at 110 °C holding for 6 h. XPS results show that nitrogen ions have been doped into the TiO₂ lattice successfully and the UV–Vis absorption spectra indicate that the light absorption edge of the N-doped TiO₂ has been red-shifted into visible light region. The photocatalytic performance of the N-doped TiO₂ thin film prepared from the synthesized hydrosol was evaluated by photodegrading the gaseous formaldehyde (HCHO) under visible light irradiation. The photodegradation ratio of HCHO reached up to 90% within 24 h and the degradation ratio was stable for ten degradation cycles, indicating the prepared hydrosol has good reusable performance in photodegrading gaseous pollutants.     

Research on photodegradation of formaldehyde by nanocrystalline N-TiO<Subscript>2</Subscript> powders under visible light irradiation

The photo-degradation of formaldehyde (HCHO) by nitrogen-doped nanocrystalline TiO₂ (N-TiO₂) powders under visible light irradiation has been systematically investigated. Experimental results show that the degradation ratio reached up to 42.6% after 2 h visible light irradiation when the amounts of N-TiO₂ powders were 0.5 g, the initial concentration of the HCHO was set at 0.98 mg/m³, the illumination intensity was fixed at 10,000 lux, the ambient temperature was set at 26 °C, and the relative humidity was maintained at 33 ± 5%. Further research shows that the degradation ratios were all larger than 40% in ten repeated cycles of photodegradation of HCHO by N-TiO₂ powders. The degradation ratio was as high as 82.9% after 2 h visible light irradiation when the amount of N-TiO₂ was 5 g. The degradation ratio was increased from 25.5 to 59.6% when the illumination intensity of the visible light was increased from 0 to 30,000 lux. However, the degradation ratio could not be further increased by further increasing the illumination intensity.     

In situ growth of MnO2 on pDA-templated cotton fabric for degradation of formaldehyde

Degradation of formaldehyde (HCHO) in interior decoration has been an urgent issue due to its toxicity nature and potential threats to human health. In this work, manganese dioxide nanoparticles (MnO₂ NPs) were in situ grown on the polydopamine (pDA)-templated cotton fabrics for environmentally friendly HCHO degradation applications. The morphology, elemental composition, and crystal structure of the cotton/pDA/MnO₂ were characterized by scanning electron microscopy–energy dispersive X-ray spectrum, Fourier transform infrared, X-ray diffractometer and X-ray photoelectron spectroscopy, respectively. The degradation of HCHO by the as-developed cotton/pDA/MnO₂ was measured in a self-made quartz reactor, and the stability of adsorption was evaluated by cyclic experiments. The results showed that the HCHO removal efficiency reached to 100% within 20 min after three cycles, suggesting that the as-prepared fabrics exhibited good stability for the degradation of HCHO. The development of MnO₂ NPs coated fabrics provides new strategies in degradation HCHO in interior decoration.

     

Rapid removal of anionic organic dye from contaminated water using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite low-cost adsorbent via adsorption techniques

This research study aims to remove hazardous anionic azo dyes (Congo red (CR)) from aqueous solutions via a simple adsorption method using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite (P3ABA/GO/CoFe₂O₄) as a novel and low-cost nanoadsorbent, as synthesized by a simple and straightforward polymerization method. Typically, 3-aminobenzoic acid (3ABA), as monomer, was chemically polymerized with graphene oxide (GO) and cobalt ferrite (CoFe₂O₄) in an aqueous acidic medium containing an ammonium persulfate initiator. The adsorbent P3ABA/GO/CoFe₂O₄ nanocomposite was characterized using various techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, scanning electron microscopy, energy-dispersive analysis by X-ray and Brunauer–Emmett–Teller, vibrating sample magnetometer, and zeta potential techniques. These techniques confirmed the interaction between the poly(3-aminobenzoic acid) with GO and CoFe₂O₄ due to the presence of π-π interactions, hydrogen bonding, and electrostatic forces. Herein, the removal efficiency of dye from aqueous solution by the adsorbent was studied according to several parameters such as the pH of the solution, dye concentration, dosage of adsorbent, contact time, and temperature. The adsorption of the dye was fitted using a Langmuir model (R² between 0.9980 and 0.9995) at different temperatures, and a kinetic model that was pseudo-second order (R² = between 0.9993 and 0.9929) at various initial concentrations of CR dye. In addition, the data revealed that the P3ABA/GO/CoFe₂O₄ nanocomposite exhibited a high adsorption capacity (153.92 mg/g) and removal for CR dye (98 %) at pH 5. Thermodynamic results showed the adsorption process was an endothermic and spontaneous reaction. It was found that, in terms of reusability, the P3ABA/GO/CoFe₂O₄ adsorbent can be used for up to six cycles. In this study, P3ABA/GO/CoFe₂O₄ nanocomposites were found to be low cost, and have an excellent removal capability and fast adsorption rate for CR from wastewater via a simple adsorption method. Moreover, this adsorbent nanocomposite could be simply separated from the resultant solution and recycled.     

Removal of cibacron blue 3G-A (CB) dye from aqueous solution using chemo-physically activated biochar from oil palm empty fruit bunch fiber

A novel biodegradable adsorbent called pyrolysed empty fruit bunch fibres (PEF) was prepared by chemo-physical activation of empty fruit bunch fibres (EFB) biochar for removal of cibacron blue 3G-A (CB) dye from aqueous solution. PEF was characterized using FTIR, SEM-EDX, XRD and BET techniques. The N₂ adsorption-desorption isotherms indicated PEF’s surface area to be 362.84 m²g⁻¹ and XRD attributed amorphous nature to PEF. After adsorption process, PEF has smoother surface morphology, increase in carbon by weight and shift in functional groups. The established adsorption optimum conditions were pH 10, 45 min contact time and 0.10 g/100 mL adsorbent dosage with 99.05% CB dye removal capacity at 343 K and initial dye concentration 100 mg/L. Desorption ratio >90% after seventh cycle of adsorption-desorption experiments confirmed high reusability (regeneration) of PEF. Pseudo second order kinetic and Freundlich were better fitted with kinetic and isotherm model respectively, while mechanism of adsorption was controlled by film diffusion (external mass transfer). Thermodynamic studied revealed ΔG, ΔS and ΔH to be −3.12 MJ/mol K, 9.11 kJ/mol K, 6.83 kJ/mol respectively at 343 K. The negative value of ΔG, positive values of ΔS and ΔH indicated spontaneity, feasibility and endothermic nature of CB dye adsorption from aqueous solution onto PEF.     

Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.     

Fe3O4-CuO-activated carbon composite as an efficient adsorbent for bromophenol blue dye removal from aqueous solutions

Dye wastewater from industries is posing tremendous health hazards. The lethal dyes can be eliminated using nanomaterials and scientific approach like adsorption which is facile, cheap, safe as well as ecofriendly. Fe₃O₄-CuO-AC composite was prepared by a hydrothermal method and used for the removal of dyes in wastewater. The composite material was characterized by various techniques such as XRD, SEM, EDS, TEM and FT-IR. The Fe₃O₄-CuO-AC composite was used to treat five types of dyes in water. Fe₃O₄-CuO-AC composite showed the highest adsorption capability for bromophenol blue (BPB) dye. The effects of initial concentration, pH, the amount of adsorbent and temperature were also studied. The optimum conditions were found to be 20 ppm dye concentration, pH 9, an adsorbent dose of 0.06 gL^─1 at 65 °C. A removal efficiency of 97% was obtained for BPB dye during 120 min of adsorption. Kinetic studies indicated that a pseudo-second order is the most suitable model for the adsorption process. The Fe₃O₄-CuO-AC composite showed better adsorption capacity as compare to Fe₃O₄-AC except for the Methyl green dye. The maximum adsorption capacity was found to be 88.60 mg/g for BPB. Additionally, the thermodynamic parameters (ΔS°, ΔH° and ΔG°) showed that the process was spontaneous and exothermic. All the above results revealed that the Fe₃O₄-CuO-AC compositecan be an effective adsorbent for removing dyes from wastewater.     

Microemulsion‐Assisted Preparation of a Mesoporous Ferrihydrite/SiO2 Composite for the Efficient Removal of Formaldehyde from Air

Mesoporous ferrihydrite/SiO₂ composites were synthesized according to a water‐in‐oil microemulsion method and characterized by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetry, nitrogen‐adsorption/desorption, and by X‐ray photoelectron spectroscopy. The as‐prepared porous ferrihydrite/SiO₂ composites showed an excellent adsorption performance for formaldehyde (HCHO) removal from indoor air at ambient temperature. It was found that the aging time during the synthesis had a significant impact on the pore structure, surface area, and HCHO adsorption of these materials. The ferrihydrite/SiO₂ composite that was aged for 3 h in the presence of tetraethyl orthosilicate (TEOS) exhibited a relatively high HCHO adsorption capacity, as well as good recyclability, which was attributed to a relatively large BET surface area, optimal pore size, a suitable Si/Fe atomic ratio, and a synergistic effect between ferrihydrite and SiO₂. This work not only demonstrates that porous ferrihydrite/SiO₂ composites can act as an efficient adsorbent toward HCHO, but suggests a new route for the rational design of cost‐effective and environmentally benign adsorbents with high performance for indoor air purification.     

Synthesis and application of treated activated carbon for cationic dye removal from modelled aqueous solution

Use of activated carbon (AC) prepared from rice husk and treated with anionic surfactant is investigated to eliminate cationic dye crystal violet (CV) using modelled dye solution. AC modified with anionic surfactant sodium lauryl sulfate (ACSLS) and other two surfactant namely sodium dodecyl sulfonate and hexadecyl trimethyl ammonium bromide were used for the analysis. Optimum ACSLS was analyzed and characterized using BET, XRD, SEM accompanied with XEDS, FTIR, HR-TEM and zeta potential, which confirms the sorption of CV onto ACSLS. Influence of pH, dose of adsorbent, concentration of initial dye, contact time, additive salts as well as actual water samples were investigated. Presence of NH⁴⁺, Ca²⁺, Mg²⁺, Na²⁺, Ca²⁺ and K⁺ cations in dye solution were having negligible (less than 4 %) influence on dye removal capacity. Study of mass transfer parameters revealed intra particle diffusion and film diffusion both played their part, whereas other kinetic studies has shown that experimental data fitted best with Pseudo 2nd order rate. Isotherm studies accompanied with error analysis revealed that Langmuir isotherm controls the adsorption equilibrium with highest capacity of CV adsorption with optimum operating conditions as pH = 6, temperature = 318 K, adsorbent dose = 100 mg/L and dye concentration = 30–60 mg/L. Study of thermodynamics and temperature analysis have shown that the sorption reaction was favourable and spontaneous with rise in temperature and endothermic in nature. Column studies are reported for varying rate of flow, depth of bed and dye concentrations along with analysis of column experimental data with various models like Yoon-Nelson, Thomas, Bohart-Adam and Clark model. Reusability (no. of cycles) of used adsorbent was studied using regeneration experiments. Analysis inferred that AC modified using surfactants can be a useful technique for enhanced adsorption capacity of dyes from aqueous solution and not much work has been reported on use of anionic surfactant modified AC for dye removal process.     

Quartzite an efficient adsorbent for the removal of anionic and cationic dyes from aqueous solutions

Quartzite obtained from local source was investigated for the removal of anionic dye congo red (CR) and cationic dye malachite green (MG) as an adsorbent from aqueous solution in batch experiment. The adsorption process was studied as a function of dye concentration, contact time, pH and temperature. Adsorption process was described well by Langmuir and Freundlich isotherms. The adsorption capacity remained 666.7 mg/g for CR dye and 348.125 mg/g for MG dye. Data was analyzed thermodynamically, ΔH⁰ and ΔG⁰ values proved that adsorption of CR and MG is an endothermic and spontaneous process. Adsorption data fitted best in the pseudo-first order kinetic model. The adsorption data proved that quartzite exhibits the best adsorption capacity and can be utilized for the removal of anionic and cationic dyes.     

Synthesis and performance evaluation of chitosan/zinc oxide nanocomposite as a highly efficient adsorbent in the removal of reactive red 198 from water

In this study, Chitosan and Chitosan-zinc oxide (ZnO) nanocomposite were prepared and applied as a low-cost adsorbent with high adsorption capacity for removing reactive red 198 (RR 198) dye from contaminated water. After preparation, it was characterized using FT-IR, XRD, and SEM. The effect of pH, temperature, time, adsorbent amount, and initial dye concentration were investigated in the removal efficiency of RR 198. The maximum adsorption capacity (q_m) obtained from the Langmuir equation was 172.41 mg/g in adsorbent dose of 0.1 g/L, pH: 4, temperature of 25°C, adsorption time of 40 min. The thermodynamic parameters demonstrated the spontaneous and endothermic nature of the adsorption process. Due to the high efficiency of chitosan/ZnO nanocomposite in removal of RR 198 from water and advantages such as high adsorption capacity, simple synthesis, and easy application, it can be used as an effective method in the removal of RR 198 from water.     

In situ FTIR Study of the Adsorption of Formaldehyde, Formic Acid, and Methyl Formiate at the Surface of TiO2 (Anatase)

The catalytic properties of TiO₂ (anatase) in the reactions of formaldehyde oxidation and formic acid decomposition are examined. At 100–150°C, formaldehyde is converted into methyl formate with high selectivity regardless of the presence of oxygen in the reaction mixture. Formic acid is decomposed to CO and water. Surface compounds formed in the reactions of formaldehyde, formic acid, and methyl formate with TiO₂ (anatase) are identified by in situ FTIR spectroscopy. In a flow of a formaldehyde-containing mixture at 100°C, H-bonded HCHO, dioxymethylene species, bidentate formate, and coordinatively bonded HCHO are observed on the TiO₂ surface. In the adsorption of formic acid, H-bonded HCOOH and two types of formates (bidentate and unsymmetrical formates) are formed. In the adsorption of methyl formate, H-bonded HCOOCH₃, HCOOCH₃ coordinatively bonded via the carbonyl oxygen, and bidentate formate are identified.     

Adsorption and redox chemistry of cis-RuLL'(SCN)2 with L=4,4′-dicarboxylic acid-2,2′-bipyridine and L'=4,4′-dinonyl-2,2′-bipyridine (Z907) at FTO and TiO2 electrode surfaces

The electrochemical and spectroelectrochemical properties of the sensitizer dye Z907 (cis-RuLL'(SCN)₂ with L=4,4′-dicarboxylic acid-2,2′-bipyridine and L'=4,4′-dinonyl-2,2′-bipyridine) adsorbed on fluorine-doped tin oxide (FTO) and TiO₂ surfaces have been investigated. Langmuirian binding constants for FTO and TiO₂ are estimated to be 3 × 10⁶ M⁻¹ and 4 × 10⁴ M⁻¹, respectively. The Ru(III/II) redox process is monitored by voltammetry and by spectroelectrochemistry. For Z907 adsorbed onto FTO, a slow EC-type electrochemical reaction is observed with a chemical rate constant of ca. k = 10⁻² s⁻¹ leading to Z907 dye degradation of a fraction of the FTO-adsorbed dye. The Z907 adsorption conditions affect the degradation process. No significant degradation was observed for TiO₂-adsorbed dye. Degradation of the Z907 dye affects the electron hopping conduction at the FTO–TiO₂ interface.     

Optimization of cadmium adsorption from aqueous solutions by functionalized graphene and the reversible magnetic recovery of the adsorbent using response surface methodology

Novel functionalized graphene adsorbent was prepared and characterized using different techniques. The prepared adsorbent was applied for the removal of cadmium ions from aqueous solution. A response surface methodology was used to evaluate the simple and combined effects of the various parameters, including adsorbent dosage, pH, and initial concentration. Under the optimal conditions, the cadmium removal performance of 70% was achieved. A good agreement between experimental and predicted data in this study was observed. The experimental results revealed of cadmium adsorption with high linearity follow Langmuir isotherm model with maximum adsorption capacity of 502 mg g^?1, and the adsorption data fitted well into pseudo‐second order model. Thermodynamic studies showed that adsorption process has exothermic and spontaneous nature. The recommended optimum conditions are: cadmium concentration of 970 mg L^?1, adsorbent dosage of 1 g L^?1, pH of 6.18, and T = 25 °C. The magnetic recovery of the adsorbent was performed using a magnetic surfactant to form a noncovalent magnetic functionalized graphene. After magnetic recovery of the adsorbent both components (adsorbent and magnetic surfactant) were recycled by tuning the surface charges through changing the pH of the solution. Desorption behavior studied using HNO₃ solution indicated that the adsorbent had the potential for reusability.     

Photocatalytic degradation of triazine dyes over N-doped TiO2 in solar radiation

Photocatalytic degradation of the reactive triazine dyes Reactive Yellow 84 (RY 84), Reactive Red 120 (RR 120), and Reactive Blue 160 (RB 160) on anatase phase N-doped TiO₂ in the presence of natural sunlight has been carried out in this work. The effect of experimental parameters like initial pH and concentration of dye solution and dosage of the catalyst on photocatalytic degradation have also been investigated. Adsorption of dyes on N-doped TiO₂ was studied prior to photocatalytic studies. The studies show that the adsorption of dyes on N-doped TiO₂ was high at pH 3 and follows the Langmuir adsorption isotherm. The Langmuir monolayer adsorption capacity of dyes on N-doped TiO₂ was 39.5, 86.0, and 96.3 mg g^?1 for RY 84, RR 120, and RB 160, respectively. The photocatalytic degradation of the dyes follows pseudo first-order kinetics and the rate constant values are higher for N-doped TiO₂ when compared with that of undoped TiO₂. Moreover, the degradation of RY 84 on N-doped TiO₂ in sunlight was faster than the commercial Aeroxide^® P25. However, the P25 has shown higher photocatalytic activity for the other two dyes, RR 120 and RB 160. The COD of 50 mg l^?1 Reactive Yellow-84, RR 120 and RB 160 was reduced by 65.1, 73.1, and 69.6 %, respectively, upon irradiation of sunlight for 3 h in the presence of N-doped TiO₂. The photocatalyst shows low activity for the degradation of RY 84 dye, when its concentration was above 50 mg l^?1, due to the strong absorption of photons in the wavelength range 200–400 nm by the dye solution. LC–MS analysis shows the presence of some triazine compounds and formimidamide derivatives in the dye solutions after 3 h solar light irradiation in the presence of N-doped TiO₂.     

Removal of Rhodamine B,a Cationic Dye From Aqueous Solution Using Poly(cyclotriphosphazene-co-4,4′-sulfonyldiphenol) Nanotubes

Poly(cyclotriphosphazene-co-4,4′-sulfonyldiphenol) (PZS) nanotubes were evaluated as an efficient adsorbent for the removal of Rhodamine B (RhB), a cationic dye from aqueous solution. The as-synthesized adsorbent (PZS nanotubes) were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) and N₂ adsorption/desorption isotherms. The factors influencing the adsorption efficiency and capacity had been systematically studied. Results showed that the adsorption was highly dependent on temperature, initial RhB concentration and adsorbent dose. Effects of initial solution pH indicate that the adsorption can proceed in both basic and acidic environment. The equilibrium absorption capacity at 25°C can reach up to 35.58 mg/g within 60 min implying the adsorption procedure was highly rapid. The kinetic data was better described by the pseudo-second-order model with the correlation coefficient (R² = 0.9981), and the adsorption process followed Weber's intraparticle model, indicating the adsorption process could be divided into two stages. Results also showed that the adsorption equilibrium obeyed the Langmuir isotherm, and the value of equilibrium parameter R_L suggested that the PZS nanotubes were an efficient adsorbent for the removal of RhB from aqueous solution.