Thermodynamic analysis of the phase separation during the polymerization of a thermoset system into a thermoplastic matrix. I. Effect of the composition on the cloud‐point curves

The cloud‐point curves of polystyrene (PS) mixed with reactive epoxy monomers based on diglycidyl ether of bisphenol A with stoichiometric amounts of 4,4′‐methylenebis(2,6‐diethylaniline) were experimentally studied. A thermodynamic analysis of the phase‐separation process in these epoxy‐modified polymers was performed that considered the composition dependence of the interaction parameter, χ(T,Φ₂) (where T is the temperature and Φ₂ is the volume fraction of polystyrene), and the polydispersity of both polymers. In this analysis, χ(T,Φ₂) was considered the product of two functions: one depending on the temperature [D(T)] and the other depending on the composition [B(Φ₂)]. For mixtures without a reaction, the cloud‐point curves showed upper critical solution temperature behavior, and the dependence of χ(T,Φ₂) on the composition was determined from the threshold point, that is, the maximum cloud‐point temperature. During the isothermal reactions of mixtures with different initial PS concentrations, the dependence of χ(T,Φ₂) on the composition was determined under the assumption that, at each conversion level, the D(T) contribution to the χ(T,Φ₂) value had to be constant independently of the composition. For these mixtures, it was demonstrated that the changes in the chemical structure produced by the epoxy–amine reaction reduced χ(T,Φ₂). This effect was more important at lower volume fractions of PS. Nevertheless, the decrease in the absolute value of the entropic contribution to the free energy of mixing was the principal driving force behind the phase‐separation process. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1351–1360, 2004     

Effect of composition on the width of the calorimetric glass transition in polymer–solvent and solvent–solvent mixtures

The calorimetric glass‐transition temperature (T_g) and transition width were measured over the full composition range for solvent–solvent mixtures of o‐terphenyl with tricresyl phosphate and with dibutyl phthalate and for polymer–solvent mixtures of polystyrene with three dialkyl phthalates. T_g shifted smoothly to higher temperatures with the addition of the component with the higher T_g for both sets of solvent–solvent mixtures. The superposition of the differential scanning calorimetry traces showed almost no composition dependence for the width of the transition region. In contrast, the composition dependence of T_g in polymer–solvent mixtures was different at high and low polymer concentrations, and two distinct T_g's were observed at intermediate compositions. These results were interpreted in terms of the local length scale and associated local composition variations affecting T_g. The possible implications of these results for the dynamics of miscible polymer blends were examined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1155–1163, 2004     

A new technique for measuring retrograde vitrification in polymer–gas systems and for making ultramicrocellular foams from the retrograde phase

A stepwise temperature‐ and pressure‐scanning thermal analysis method was developed to measure glass‐transition temperature T_g in the two‐phase polymer–gas systems as a function of gas pressure p, and was used to confirm recent theoretical predictions that certain polymer–gas systems exhibit retrograde vitrification, that is, they undergo rubber‐to‐glass transition on heating. A complete T_g‐p profile delineating the glass–rubber phase envelope was established for the PMMA‐CO₂ system. The retrograde vitrification behavior observed, where at certain gas pressures the polymer exists in the rubbery state at low and high temperatures and in the glassy state at intermediate temperatures, was similar to that reported previously based on the creep‐compliance measurements. The existence of the rubbery state at low temperatures was used to generate foams by saturating the polymer with CO₂ at 34 atm and at temperatures in the range −0.2 to 24 °C followed by foaming at temperatures in the range 24 to 90 °C. Foams with very fine cell structure never reported before could be prepared by this technique. For example, PMMA foams with average cell size of 0.35 μm and cell density of 4.4 × 10¹³ cells/g were prepared by processing the low temperature rubbery phase. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 716–725, 2000     

Equilibrium phase diagram of polystyrene and 8CB

The experimental equilibrium phase diagram of a mixture of linear polystyrene of molecular weight M_w = 44,000 g/mol and 4‐cyano‐4′‐n‐octyl‐biphenyl (8CB) is established. The three transitions smectic A‐nematic, nematic‐isotropic, and isotropic‐isotropic are observed. The first two are observed both by optical microscopy and differential scanning calorimetry (DSC) while the isotropic‐isotropic transition could be seen only via optical microscopy. Two series of samples with the same compositions were independently prepared and yielded consistent results both by microscopy and DSC. Measurements of sample compositions with less than 50 weight % of 8CB were influenced by the vicinity of the glass transition temperature (T_g) of the polymer in the mixture. This quantity is also determined by DSC as a function of composition. A single T_g is observed, which decreases with composition of the LC. Other thermodynamic quantities such as the enthalpy variations of LC in the nematic‐isotropic transition and the fraction of LC contained in the droplets are also considered. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1841–1848, 1999     

Miscibility behavior and hydrogen bonding in blends of poly(vinyl phenyl ketone hydrogenated) and poly(2‐ethyl‐2‐oxazoline)

The miscibility behavior of poly(2‐ethyl‐2‐oxazoline) (PEOx)/poly(vinyl phenyl ketone hydrogenated) (PVPhKH) blends was studied for the entire range of compositions. Differential scanning calorimetry and thermomechanical analysis measurements showed that all the PEOx/PVPhKH blends studied had a single glass‐transition temperature (T_g). The natural tendency of PVPhKH to self‐associate through hydrogen bonding was modified by the presence of PEOx. Partial IR spectra of these blends suggested that amide groups in PEOx and hydroxyl groups in PVPhKH interacted through hydrogen bonding. This physical interaction had a positive influence on the phase behavior of PEOx/PVPhKH blends. The Kwei equation for T_g as a function of the blend composition was satisfactorily used to describe the experimental data. Pure‐component pressure–volume–temperature data were also reported for both PEOx and PVPhKH. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 636–645, 2004     

Phase separation dynamics of a poly(vinyl methyl ether)/polystyrene (PVME/PS) blend studied by ultrafast differential scanning calorimetry

In this work, ultrafast differential scanning calorimetry (UFDSC) is used to study the dynamics of phase separation. Taking poly(vinyl methyl ether)/polystyrene (PVME/PS) blend as the example, we firstly obtained the phase diagram that has lower critical solution temperature (LCST), together with the glass transition temperature (T_g) of the homogeneous blend with different composition. Then, the dynamics of the phase separation of the PVME/PS blend with a mass ratio of 7:3 was studied in the time range from milliseconds to hours, by the virtue of small time and spatial resolution that UFDSC offers. The time dependence of the glass transition temperature (T_g) of PVME‐rich phase, shows a distinct change when the annealing temperature (T_a) changes from below to above 385 K. This corresponds to the transition from the nucleation and growth (NG) mechanism to the spinodal decomposition (SD) mechanism, as was verified by morphological and rheometric investigations. For the SD mechanism, the temperature‐dependent composition evolution in PVME‐rich domain was found to follow the Williams–Landel–Ferry (WLF) laws. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1357–1364     

Glass transition temperatures of butyl acrylate–methyl methacrylate copolymers

The glass transition temperatures T_g of butyl acrylate–methyl methacrylate copolymers obtained by free radical polymerization in 3 and 5 mol/L benzene solution have been measured using differential scanning calorimetry (DSC) and the values have been correlated using Johnston's equation with inter‐intramolecular copolymer structure. From the data calculated with copolymer prepared at low conversion, the variation of glass transition temperature with copolymer conversion has been theoretically predicted. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2512–2520, 1999     

High‐throughput kinetic analysis of acrylate and thiol‐ene photopolymerization using temperature and exposure time gradients

In this work, a high‐throughput technique for evaluating photopolymers is developed to enable simultaneous measurement of the effects of temperature in combination with exposure time. Temperature and exposure time gradients were produced in orthogonal directions on a single sample, and subsequently sampled using Fourier transform infrared (FTIR) spectroscopy. The technique developed here allows for photopolymerization kinetics to be analyzed rapidly over a large range of industrially relevant temperatures, giving insight into the role temperature and the polymer's glass transition temperature have in dictating the photopolymerization kinetics. In the 70/30 wt % hexyl acrylate and hexanediol diacrylate system, conversion in samples below the glass transition temperature (T_G) was 66 ± 2% after 12 s, significantly lower than the 93 ± 4% conversion at 12 s for samples polymerized at temperatures above the T_G. In addition, a thiol‐ene system was analyzed to study the effect of temperature on the ene homopolymerization in allyl ether monomers, which leads to incomplete thiol conversion in stoichiometrically balanced systems. At a 60% thiol conversion, the allyl ether‐ene conversion at all temperatures is 65 ± 3% irrespective of initial formulation temperature, indicative of the homopolymerization behavior being nearly independent of temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1502–1509, 2008     

Molecular relaxation of isotactic polystyrene: Real‐time dielectric spectroscopy and X‐ray scattering studies*

The molecular relaxation processes and structure of isotactic polystyrene (iPS) films were investigated with real‐time dielectric spectroscopy and simultaneous wide‐ and small‐angle X‐ray scattering. The purpose of this work was to explore the restrictions imposed on molecular mobility in the vicinity of the α relaxation (glass transition) for crystallized iPS. Isothermal cold crystallization at temperatures of T_c = 140 or 170 °C resulted in a sigmoidal increase of crystallinity with crystallization time. The glass‐transition temperature (T_g), determined calorimetrically, exhibited almost no increase during the first stage of crystal growth before impingement of spherulites. After impingement, the calorimetric T_g increased, suggesting that confinement effects occur in the latter stages of crystallization. For well‐crystallized samples, the radius of the cooperativity region decreased substantially as compared with the purely amorphous sample but was always smaller than the layer thickness of the mobile amorphous fraction. Dielectric experiments directly probed changes in the amorphous dipole mobility. The real‐time dielectric data were fitted to a Havriliak–Negami model, and the time dependence of the parameters describing the distribution of relaxation times and dielectric strength was obtained. The central dipolar relaxation time showed little variation before spherulite impingement but increased sharply during the second stage of crystal growth as confinement occurred. Vogel–Fulcher–Tammann analysis demonstrated that the dielectric reference temperature, corresponding to the onset of calorimetric T_g, did not vary for well‐crystallized samples. This observation agreed with a model in which constraints affect primarily the modes having longer relaxation times and thus broaden the glass‐transition relaxation process on the higher temperature side. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 777–789, 2004     

Above,below, and in‐between the two glass transitions of ultrathin free‐standing polystyrene films: Thermal expansion coefficient and physical aging

In previous work we observed two simultaneous transitions in high molecular weight (MW) free‐standing polystyrene films that were interpreted as two thickness‐dependent reduced glass transition temperatures (T_gs). The weaker lower transition agreed well with the MW‐dependent T_g(h) previously reported, while the much stronger upper transition matched the MW‐independent T_g(h) previously observed in low‐MW free‐standing films. Here, we investigate the nature of these two transitions by inspecting the temperature dependence of the films' thermal coefficient of expansion (TCE) and present physical aging measurements using ellipsometry both below and in‐between the two transitions. TCE values indicate approximately 80 to 90% of the film solidifies at the upper transition, while only 10 to 20% remains mobile to lower temperatures, freezing out at the lower transition. Physical aging is observed at a temperature below the upper transition, but above the lower transition, indicative of the upper transition being an actual glass transition associated with the α‐relaxation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 64–75     

Amine‐cured epoxy/clay nanocomposites. II. The effect of the nanoclay aspect ratio

The thermophysical and mechanical properties of a nanocomposite material composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay are reported. The storage modulus at 100 °C, which was above the glass‐transition temperature (T_g), increased approximately 350% with the addition of 10 wt % (6.0 vol %) of clay. Below the T_g, the storage modulus at 30 °C increased 50% relative to the value of unfilled epoxy. It was determined that the T_g linearly increased as a function of clay volume percent. The tensile modulus of epoxy at room temperature increased approximately 50% with the addition of 10 wt % of clay. The reinforcing effect of the organoclay nanoplatelets is discussed with respect to the Tandon–Weng and Halpin–Tsai models. A pseudoinclusion model is proposed to describe the behavior of randomly oriented, uniformly dispersed platelets in nanocomposite materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4391–4400, 2004     

Effect of sample preparation on the glass‐transition of thin polystyrene films

We have investigated the effect of sample preparation on the glass‐transition temperature (T_g) of thin films of polystyrene (PS). By preparing and measuring the glass‐transition temperature T_g of multilayered polymer films, we are able to assess the contribution of the spincoating process to the reduced T_g values often reported for thin PS films. We find that it is possible to determine a T_g even on the first heating cycle, and that by the third heating cycle (a total annealing time of 15 min at T = 393 K) the T_g value has reached a steady state. By comparing multilayered versus single layered films we find that the whole T_g depends only on the total film thickness, and not on the thickness of the individual layers. These results strongly suggest that the spincasting process does not contribute significantly to T_g reductions in thin polymer films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4503–4507, 2004     

Influence of carboxyl‐terminated (butadiene‐co‐acrylonitrile) loading on the mechanical and thermal properties of cured epoxy blends

A mixture of epoxy with liquid nitrile rubber, carboxyl‐terminated (butadiene‐co‐acrylonitrile) (CTBN) was cured under various temperatures. The cured resin was a two‐phase system, where spherical rubber domains were dispersed in the matrix of epoxy. The morphology development during cure was investigated by scanning electron microscope (SEM). There was slight reduction in the glass transition temperature of the epoxy matrix (T_g) on the addition of CTBN. It was observed that, for a particular CTBN content, T_g was found to be unaffected by the cure temperature. Bimodal distribution of particles was noted by SEM analysis. The increase in the size of rubber domains with CTBN content is due probably to the coalescence of the rubber particles. The mechanical properties of the cured resin were thoroughly investigated. Although there was a slight reduction in tensile strength and young's modulus, appreciable improvements in impact strength, fracture energy, and fracture toughness were observed. Addition of nitrile rubber above 20 parts per hundred parts of resin (phr) made the epoxy network more flexible. The volume fraction of dispersed rubbery phase and interfacial area were increased with the addition of more CTBN. A two‐phase morphology was further established by dynamic mechanical analysis (DMA). © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2531–2544, 2004     

Electric,dielectric, and dynamic mechanical behavior of carbon black/styrene‐butadiene‐styrene composites

The conductivity of styrene‐butadiene‐styrene block copolymers containing different amounts of extraconductive carbon black (CB) was investigated as a function of the mold temperature. The composites exhibited reduced percolation thresholds (between 1.0 and 2.0 vol % CB). The dynamic mechanical analysis characterization revealed that the glass‐rubber‐transition temperatures of both segments were not affected by the CB addition, although the damping of the polybutadiene phase displayed a progressive drop with an increase in the CB concentration. The normalized curves of tan δ/tan δ_max (where tan δ represents the value of the loss tangent at any measurement temperature and tan δ_max represents the loss tangent peak value at the corresponding temperature T_max) versus T/T_max (where T is the temperature and T_max is the maximum temperature), corresponding to both polystyrene and polybutadiene phases as well as the activation energy related to the glass‐rubber‐transition process, did not present any significant change with the addition of CB. The dielectric analysis revealed the presence of two relaxation peaks in the composite containing 1.5 vol % CB, the magnitude of which was strongly influenced by the frequency, being attributed to interfacial Maxwell‐Wagner‐Sillars relaxations caused by the presence of different interfaces in the composite. The mechanical properties were not affected by the presence of CB at concentrations of up to 2.5 vol %. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2983–2997, 2003     

Stereoselective nucleophilic substitution of poly(vinyl chloride) with potassium 4‐acetamidothiophenolate

The nucleophilic substitution reaction of poly(vinyl chloride) (PVC) with potassium 4‐acetamidothiophenolate was performed in a cyclohexanone solution. The quantitative microstructural analysis, as a function of the conversion, was followed by ¹³C NMR spectroscopy. Through a comparison of the microstructural changes with the degree of substitution, a small fraction of mmr tetrads was found to react occasionally with the central chlorine of the mr triad instead of the mm, such as for sodium benzenethiolate (NaBT). This conclusion was confirmed by Fourier transform infrared results. However, unlike NaBT, the evolution of the glass‐transition temperature (T_g) with the degree of conversion changed with the degree of substitution similarly to the ratio of the extents to which mmr and rrmr structures intervened in the substitution reaction. From these studies, it followed that the specific interactions due to the polar nature of the nucleophile enhanced the molecular‐microstructure‐based mechanisms, which were responsible for T_g. Such a novel quantitative correlation, compared with more tentative ones obtained previously, presents valuable insight into the role of the stereochemical microstructure in the glass‐transition process in PVC. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1857–1867, 2004     

Glass transition and relaxation behavior of epoxy nanocomposites

With advances in nanoscience and nanotechnology, there is increasing interest in polymer nanocomposites, both in scientific research and for engineering applications. Because of the small size of nanoparticles, the polymer–filler interface property becomes a dominant factor in determining the macroscopic material properties of the nanocomposites. The glass‐transition behaviors of several epoxy nanocomposites have been investigated with modulated differential scanning calorimetry. The effect of the filler size, filler loading, and dispersion conditions of the nanofillers on the glass‐transition temperature (T_g) have been studied. In comparison with their counterparts with micrometer‐sized fillers, the nanocomposites show a T_g depression. For the determination of the reason for the T_g depression, the thermomechanical and dielectric relaxation processes of the silica nanocomposites have been investigated with dynamic mechanical analysis and dielectric analysis. The T_g depression is related to the enhanced polymer dynamics due to the extra free volume at the resin–filler interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3849–3858, 2004     

Tuning the LCST of poly(2‐cyclopropyl‐2‐oxazoline) via gradient copolymerization with 2‐ethyl‐2‐oxazoline

Poly(2‐propyl‐oxazoline)s can be prepared by living cationic ring‐opening polymerization of 2‐oxazolines and represent an emerging class of biocompatible polymers exhibiting a lower critical solution temperature in aqueous solution close to body temperature. However, their usability is limited by the irreversibility of the transition due to isothermal crystallization in case of poly(2‐isopropyl‐2‐oxazoline) and the rather low glass transition temperatures (T_g < 45 °C) of poly(2‐n‐propyl‐2‐oxazoline)‐based polymers. The copolymerization of 2‐cyclopropyl‐2‐oxazoline and 2‐ethyl‐2‐oxazoline presented herein yields gradient copolymers whose cloud point temperatures can be accurately tuned over a broad temperature range by simple variation of the composition. Surprisingly, all copolymers reveal lower T_gs than the corresponding homopolymers ascribed to suppression of interchain interactions. However, it is noteworthy that the copolymers still have T_gs > 45 °C, enabling convenient storage in the fridge for future biomedical formulations. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3118–3122     

Curing kinetics and glass‐transition temperature of hexamethylene diisocyanate‐based polyurethane

The curing process of hexamethylene diisocyanate‐based polyurethane has been monitored by applying FTIR and DSC methods. A general relationship between glass‐transition temperature (T_g) and conversion of curing process has been obtained. This suggests that the reaction path and the relative reaction rates are independent of the curing temperature. The reaction kinetics of the system is analyzed using the T_g data converted to the conversion of the curing process. A set of experimental data and one theoretical model of T_g versus chemical conversion are presented to prove the assumption where a direct one‐to‐one relationship between the T_g (as measured) and the chemical conversion is obtained. Apparent activation energies (E_a) obtained by applying three different methods suggest good agreement. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2213–2220, 2000     

Viscoelastic characteristics of plasticized cellulose nanocomposites

The plasticization effects of cellulose diacetate composite systems including nanoparticles (montmorillonite, MMT) and plasticizers(diethyl phthalate, DEP) were investigated by the time–temperature superposition technique and viscoelastic modeling. Exhibiting the highest modulus value in the glass state, the viscoelastic modulus of the MMT nanocomposite rapidly decreased above the glass‐transition temperature (T_g). The Arrhenius‐type activation energy of pristine cellulose acetate showed the lowest value of activation energy and both DEP‐plasticized and MMT‐reinforced systems exhibited increased values of activation energy. Although the free volume fraction at the T_g decreased with the plasticizer content, it increased with the incorporation of MMT, seemingly preventing the polymer chains from being arranged in an ordered structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 59–65, 2005