Block copolymer compatibilizers for polystyrene/poly(dimethylsiloxane) blends

Symmetric polystyrene (PS)–poly(dimethylsiloxane) (PDMS) diblock copolymers were mixed into a 20% dispersion of PDMS in PS. The effect of adding the block copolymer on the blend morphology was examined as a function of the block copolymer molecular weight (M_n,bcp), concentration, and viscosity ratio (η_r). When blended together with the PS and PDMS homopolymers, most of the block copolymer appeared as micelles in the PS matrix. Even when the copolymer was preblended into the PDMS dispersed phase, block copolymer micelles in the PS matrix phase were observed with transmission electron microscopy after mixing. Adding 16 kg/mol PS–PDMS block copolymer dramatically reduced the PDMS particle size, but the morphology, as examined by scanning electron microscopy, was unstable upon thermal annealing. Adding 156 kg/mol block copolymer yielded particle sizes similar to those of blends with 40 or 83 kg/mol block copolymers, but only blends with 83 kg/mol block copolymer were stable after annealing. For a given value of M_n,bcp, a minimum PDMS particle size was observed when η_r ～ 1. When η_r = 2.6, thermally stable, submicrometer particles as small as 0.6 μm were observed after the addition of only 3% PS–PDMS diblock (number‐average molecular weight = 83 kg/mol) to the blend. As little as 1% 83 kg/mol block copolymer was sufficient to stabilize a 20% dispersion of 1.1‐μm PDMS particles in PS. Droplet size reduction was attributed to the prevention of coalescence caused by small amounts of block copolymer at the interface. The conditions under which block copolymer interfacial adsorption and interpenetration were facilitated were explained with Leibler's brush theory. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 346–357, 2002; DOI 10.1002/polb.10098     

Strongly segregated cubic microdomain morphology consistent with the double gyroid phase in high molecular weight diblock copolymers of polystyrene and poly(dimethylsiloxane)

We report the observation of a cubic phase consistent with the double gyroid structure in strongly segregated diblock copolymers of PS‐b‐PDMS over a volume fraction (φ_PDMS) range of ～0.39 to 0.45. The samples have respective molecular weights of 127 kg/mol and 73 kg/mol and degree of segregation Nχ equal to 187 and 106, respectively, at annealing temperature of 130 °C. It is important to highlight that two out of the total four samples investigated, exhibited hexagonally close packed cylindrical domains of PDMS and alternating lamellae at φ_PDMS = 0.39 and 0.45, respectively, indicating the possible narrow range of the DG morphology for the specific diblock copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2419–2427, 2009     

Nanostructured thermoset epoxy resin templated by an amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) diblock copolymer

An amphiphilic poly(ethylene oxide)‐block‐poly(dimethylsiloxane) (PEO–PDMS) diblock copolymer was used to template a bisphenol A type epoxy resin (ER); nanostructured thermoset blends of ER and PEO–PDMS were prepared with 4,4′‐methylenedianiline (MDA) as the curing agent. The phase behavior, crystallization, hydrogen‐bonding interactions, and nanoscale structures were investigated with differential scanning calorimetry, Fourier transform infrared spectroscopy, transmission electron microscopy, and small‐angle X‐ray scattering. The uncured ER was miscible with the poly(ethylene oxide) block of PEO–PDMS, and the uncured blends were not macroscopically phase‐separated. Macroscopic phase separation took place in the MDA‐cured ER/PEO–PDMS blends containing 60–80 wt % PEO–PDMS diblock copolymer. However, the composition‐dependent nanostructures were formed in the cured blends with 10–50 wt % PEO–PDMS, which did not show macroscopic phase separation. The poly(dimethylsiloxane) microdomains with sizes of 10–20 nm were dispersed in a continuous ER‐rich phase; the average distance between the neighboring microdomains was in the range of 20–50 nm. The miscibility between the cured ER and the poly(ethylene oxide) block of PEO–PDMS was ascribed to the favorable hydrogen‐bonding interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3042–3052, 2006     

Synthesis and characterization of model diblock copolymers of poly(dimethylsiloxane) with poly(1,4‐butadiene) or poly(ethylene)

Model diblock copolymers of poly(1,4‐butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS, were synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene and hexamethylciclotrisiloxane (D₃) in the presence of sec‐BuLi. By homogeneous hydrogenation of PB‐b‐PDMS, the corresponding poly(ethylene) and poly(dimethylsiloxane) block copolymers, PE‐b‐PDMS, were obtained. The synthesized block copolymers were characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size‐exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and rheology. SEC combined with ¹H NMR analysis indicates that the polydispersity index of the samples (M_w/M_n) is low, and that the chemical composition of the copolymers varies from low to medium PDMS content. According to DSC and TGA experiments, the thermal stability of these block copolymers depends on the PDMS content, whereas TEM analysis reveals ordered arrangements of the microphases. The morphologies observed vary from spherical and cylindrical to lamellar domains. This ordered state (even at high temperatures) was further confirmed by small‐amplitude oscillatory shear flow tests. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1579–1590, 2006     

Synthesis of polybutadiene‐graft‐poly(dimethylsiloxane) and polyethylene‐graft‐poly(dimethylsiloxane) copolymers with hydrosilylation reactions

We report preliminary results for the synthesis of polyethylene‐graft‐poly(dimethylsiloxane) copolymers obtained by catalytic hydrogenation of polybutadiene‐graft‐poly(dimethylsiloxane) copolymers (PB‐g‐PDMS). These last copolymers were synthesized by hydrosilylation reactions between commercial polybutadiene and ω‐silane poly(dimethylsiloxane). The reaction was carried in solution catalyzed by cis‐dichloro bis(diethylsufide) platinum(II) salt. The PB‐g‐PDMS copolymers were analyzed by ¹H and ¹³C NMR spectroscopies, and the relative weight percentages of the grafted poly(dimethylsiloxane) macromonomer were determined from the integrated peak areas of the spectra. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2920–2930, 2004     

The effect of polyethylene addition on the morphology of polystyrene/polyamide blends

The effect of a small admixture of high‐density polyethylene (HDPE) with a high or low viscosity to polystyrene/polyamide (PS/PA) blends of various compositions was studied. PS/PA blends with composition near 50/50 form sheet‐like or fiber‐like morphology at mixing that passes to the cocontinuous structure during compression molding. Ternary PS/PA/HDPE blends with PS/PA ratio about 50/50 show similar behavior. Generally, neither continuity nor shape of PS and PA phases was changed qualitatively by the addition of a small amount of HDPE. In agreement with existing rules for ternary blends, HDPE particles prefer a contact with PS phase to PA phase. On the other hand, none of these rules explains why a number of small HDPE subinclusions were dispersed into PS particles instead of HDPE‐PS core‐shell structure with a lower Gibbs free energy. Quantitative evaluation of the size of PA particles in blends with PS matrix showed that the previously proposed rule stating, that the addition of a small amount of a third immiscible component leads to a strong decrease in the size of dispersed particles, was not valid for the blends studied in this work. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2158–2170, 2009     

Control of self‐organized low‐dimensional morphology in poly(styrene‐b‐4vinylpyridine)/polystyrene blend thin films

The surface morphologies of poly(styrene‐b‐4vinylpyridine) (PS‐b‐P4VP) diblock copolymer and homopolystyrene (hPS) binary blend thin films were investigated by atomic force microscopy as a function of total volume fraction of PS (?_PS) in the mixture. It was found that when hPS was added into symmetric PS‐b‐P4VP diblock copolymers, the surface morphology of this diblock copolymer was changed to a certain degree. With ?_PS increasing at first, hPS was solubilized into the corresponding domains of block copolymer and formed cylinders. Moreover, the more solubilized the hPS, the more cylinders exist. However, when the limit was reached, excessive hPS tended to separate from the domains independently instead of solubilizing into the corresponding domains any longer, that is, a macrophase separation occurred. A model describing transitions of these morphologies with an increase in ?_PS is proposed. The effect of composition on the phase morphology of blend films when graphite is used as a substrate is also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3496–3504, 2004     

High‐performance thin film composite membranes with well‐defined poly(dimethylsiloxane)‐b‐poly(ethylene glycol) copolymer additives for CO2 separation

A series of well‐defined diblock copolymers (BCPs) consisting of poly(ethylene glycol) (PEG) and poly(dimethylsiloxane) (PDMS) were synthesized and blended with commercially available PEBAX® 2533 to form the active layer of thin‐film composite (TFC) membranes, via spin‐coating. BCPs with a PEG component ranging from 1 to 10 kDa and a PDMS component ranging from 1 to 10 kDa were synthesized by a facile condensation reaction of hydroxyl terminated PEG and carboxylic acid functionalized PDMS. The BCP/PEBAX® 2533 blends up to 50 wt % on cross‐linked PDMS gutter layers were tested at 35 °C and 350 kPa. TFC membranes containing BCPs of 1 kDa PEG and 1–5 kDa PDMS produced optimal results with CO₂ permeances of approximately 1000 GPU which is an increase up to 250% of the permeance of pure PEBAX® 2533 composite membranes, while maintaining a CO₂/N₂ selectivity of 21. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1500–1511     

Synthesis and characterization of well‐defined diblock and triblock copolymers of poly(N‐isopropylacrylamide) and poly(ethylene oxide)

Well‐defined diblock and triblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly(ethylene oxide) (PEO) were successfully synthesized through the reversible addition–fragmentation chain transfer polymerization of N‐isopropylacrylamide (NIPAM) with PEO capped with one or two dithiobenzoyl groups as a macrotransfer agent. ¹H NMR, Fourier transform infrared, and gel permeation chromatography instruments were used to characterize the block copolymers obtained. The results showed that the diblock and triblock copolymers had well‐defined structures and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.2), and the molecular weight of the PNIPAM block in the diblock and triblock copolymers could be controlled by the initial molar ratio of NIPAM to dithiobenzoate‐terminated PEO and the NIPAM conversion. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4873–4881, 2004     

Novel synthesis of polyethylene–poly(dimethylsiloxane) copolymers with a metallocene catalyst

Polyethylene–poly(dimethylsiloxane) copolymers were synthesized in solution from an ethylene monomer and an ω‐vinyl poly(dimethylsiloxane) (PDMS) macromonomer at 363 and 383 K with EtInd₂ZrCl₂/methylaluminoxane as a catalyst. The copolymers obtained were characterized with Fourier transform infrared spectroscopy, ¹H and ¹³C NMR, size exclusion chromatography, and differential scanning calorimetry. The rheological properties of the molten polymers were determined under dynamic shear flow tests at small‐amplitude oscillations, whereas the physical arrangement of the phase domains was analyzed with scanning electron microscopy (SEM)/energy dispersive X‐ray (EDX). The analysis of the catalyst activity and the resulting polymers supported the idea of PDMS blocks or chains grafted to polyethylene. The changes in the rheological behavior and the changes in the Fourier transform infrared and NMR spectra were in agreement with this proposal. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2462–2473, 2004     

Polymethylene‐b‐polystyrene diblock copolymer: Synthesis,property, and application

The design and synthesis of well‐defined polymethylene‐b‐polystyrene (PM‐b‐PS, M_n = 1.3 × 10⁴–3.0 × 10⁴ g/mol; M_w/M_n (GPC) = 1.08–1.18) diblock copolymers by the combination of living polymerization of ylides and atom transfer radical polymerization (ATRP) was successfully achieved. The ¹H NMR spectrum and GPC traces of PM‐b‐PS indicated the successful extension of PS segment on the PM macroinitiator. The micellization behavior of such diblock copolymers in tetrahydrofuran were characterized by dynamic light scattering (DLS) and atomic force microscopy (AFM) techniques. The average aggregate sizes of PM‐b‐PS diblock copolymers with the same length of PM segment in tetrahydrofuran solution (1.0 mg mL^?1) increases from 104.2 nm to 167.7 nm when the molecular weight of PS segment increases. The spherical precipitated aggregates of PM‐b‐PS diblock copolymers with an average diameter of 600 nm were observed by AFM. Honeycomb porous films with the average diameter of 3.0 μm and 6.0 μm, respectively, were successfully fabricated using the solution of PM‐b‐PS diblock copolymers in carbon disulfide via the breath‐figure (BF) method under a static humid condition. The cross‐sections of low density polyethylene (LDPE)/polystyrene (PS)/PM‐b‐PS and LDPE/polycarbonate (PC)/PM‐b‐PS blends were observed by scanning electron microscope and reveal that the PM‐b‐PS diblock copolymers are effective compatilizers for LDPE/PS and LDPE/PC blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1894–1900, 2010     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). II. Effect of poly(phenylene sulfide) homopolymer solubilization of PPS‐graft‐PET copolymer on morphology and crystallization behavior

The morphology and crystallization behavior of poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) blends compatibilized with graft copolymers were investigated. PPS‐blend‐PET compositions were prepared in which the viscosity of the PPS phase was varied to assess the morphological implications. The dispersed‐phase particle size was influenced by the combined effects of the ratio of dispersed‐phase viscosity to continuous‐phase viscosity and reduced interfacial tension due to the addition of PPS‐graft‐PET copolymers to the blends. In the absence of graft copolymer, the finest dispersion of PET in a continuous phase of PPS was achieved when the viscosity ratio between blend components was nearly equal. As expected, PET particle sizes increased as the viscosity ratio diverged from unity. When graft copolymers were added to the blends, fine dispersions of PET were achieved despite large differences in the viscosities of PPS and PET homopolymers. The interfacial activity of the PPS‐graft‐PET copolymer appeared to be related to the molecular weight ratio of the PPS homopolymer to the PPS segment of the graft copolymer (M_H/M_A). With increasing solubilization of the PPS graft copolymer segment by the PPS homopolymer, the particle size of the PET dispersed phase decreased. In crystallization studies, the presence of the PPS phase increased the crystallization temperature of PET. The magnitude of the increase in the PET crystallization temperature coincided with the viscosity ratio and extent of the PPS homopolymer solubilization in the graft copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 599–610, 2000     

Monte Carlo simulation of AB diblock copolymer between surface and substrate and comparison of experimental results

The morphologies of AB diblock copolymer film between the substrate and surface were investigated via Monte Carlo simulations on simple cubic lattices. The morphological dependence of the diblock copolymer thin film on the thickness, as well as the composition and interactive intensity has been mainly studied. With the increase of A‐segments fraction, various microdomain morphologies including regular parallel stripe‐like, mesh‐like, and normal lamella near the region of the surface were generated in this work. The morphology of thin films of asymmetric diblock copolymer was found to form cylinders in a bulk system when L_z was equal to 30. The morphologies of PS‐b‐PDMS diblock copolymer films have been studied via atomic force microscopy (AFM) and transition electron microscopy (TEM) measurements. The surface morphology of the PS‐b‐PDMS copolymer thin film shows a mesh‐like microphase separated structure, and PDMS continuous phase protruded on the PS dispersed phase. The surface composition of PS‐b‐PDMS copolymer thin films was measured by means of X‐ray photoelectron spectroscopy (XPS) and ATR‐IR. The comparison results show that the experimental observations are in good agreement with the simulation results. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1835–1845, 2006     

Well‐defined PE‐b‐PDMS diblock copolymers via the combination of thiol‐ene click and esterification reactions: Facile synthesis and compatibilization for HDPE/silicone oil blends

Well‐defined diblock copolymers of linear polyethylene (PE) and poly(dimethylsiloxane) (PDMS) have been synthesized through a facile route combining the thiol‐ene click chemistry of vinyl‐terminated polyethylene (PE‐ene) and the sequential esterification reaction. The resulting diblock copolymers are characterized by ¹H NMR, FT‐IR, DSC, TGA, and TEM. In addition, the PE‐b‐PDMS diblock copolymers have been evaluated as compatibilizers in the blends of high‐density polyethylene (HDPE) and silicone oil. The morphological analysis and mechanical properties demonstrate that the compatibilized blends with low loading concentration of PE‐b‐PDMS display significant improvements in modulus of elasticity and elongation at break as compared to the uncompatibilized binary blends. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3205–3212     

Preparation of methoxy poly(ethylene glycol)/polyester diblock copolymers and examination of the gel‐to‐sol transition

Diblock copolymers consisting of methoxy poly(ethylene glycol) (MPEG) and poly(?‐caprolactone) (PCL), poly(δ‐valerolactone) (PVL), poly(L ‐lactic acid) (PLLA), or poly(lactic‐co‐glycolic acid) (PLGA) as biodegradable polyesters were prepared to examine the phase transition of diblock copolymer solutions. MPEG–PCL and MPEG–PVL diblock copolymers and MPEG–PLLA and MPEG–PLGA diblock copolymers were synthesized by the ring‐opening polymerization of ?‐caprolactone or δ‐valerolactone in the presence of HCl · Et₂O as a monomer activator at room temperature and by the ring‐opening polymerization of L ‐lactide or a mixture of L ‐lactide and glycolide in the presence of stannous octoate at 130 °C, respectively. The synthesized diblock copolymers were characterized with ¹H NMR, IR, and gel permeation chromatography. The phase transitions for diblock copolymer aqueous solutions of various concentrations were explored according to the temperature variation. The diblock copolymer solutions exhibited the phase transition from gel to sol with increasing temperature. As the polyester block length of the diblock copolymers increased, the gel‐to‐sol transition moved to a lower concentration region. The gel‐to‐sol transition showed a dependence on the length of the polyester block segment. According to X‐ray diffraction and differential scanning calorimetry thermal studies, the gel‐to‐sol transition of the diblock copolymer solutions depended on their degrees of crystallinity because water could easily diffuse into amorphous polymers in comparison with polymers with a crystalline structure. The crystallinity markedly depended on both the distinct character and composition of the block segment. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5784–5793, 2004     

Synthesis of well‐defined miktoarm star polymers of poly(dimethylsiloxane) by the combination of chlorosilane and benzyl chloride linking chemistry

A series of novel four‐arm A₂B₂ and A₂BC and five‐arm A₂B₂C miktoarm star polymers, where A is poly(dimethylsiloxane) (PDMS), B is polystyrene (PS), and C is polyisoprene (PI), were successfully synthesized by the combination of chlorosilane and benzyl chloride linking chemistry. This new and general methodology is based on the linking reaction of in‐chain benzyl chloride functionalized poly(dimethylsiloxane) (icBnCl–PDMS) with the in‐chain diphenylalkyl (icD) living centers of PS‐DLi‐PS, PS‐DLi‐PI, or (PS)₂‐DLi‐PI. icBnCl–PDMS was synthesized by the selective reaction of lithium PDMS enolate (PDMSOLi) with the chlorosilane groups of dichloro[2‐(chloromethylphenyl)ethyl]methylsilane, leaving the benzyl chloride group intact. The icD living polymers, characterized by the low basicity of DLi to avoid side reactions with PDMS, were prepared by the reaction of the corresponding living chains with the appropriate chloro/bromo derivatives of diphenylethylene, followed by a reaction with BuLi or the living polymer. The combined molecular characterization results of size exclusion chromatography, ¹H NMR, and right‐angle laser light scattering revealed a high degree of structural and compositional homogeneity in all miktoarm stars prepared. The power of this general approach was demonstrated by the synthesis of a morphologically interesting complex miktoarm star polymer composed of two triblock terpolymer (PS‐b‐PI‐b‐PDMS) and two diblock copolymer (PS‐b‐PI) arms. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6587–6599, 2006     

Library synthesis and characterization of 3‐aminopropyl‐terminated poly(dimethylsiloxane)s and poly(ϵ‐caprolactone)‐b‐poly(dimethylsiloxane)s

Libraries of 3‐aminopropyl‐terminated poly(dimethylsiloxane) (APT–PDMS) and poly(?‐caprolactone)–poly(dimethylsiloxane)–poly(?‐caprolactone) (PCL—PDMS–PCL) triblock copolymers were synthesized. Preliminary experiments were carried out to select an appropriate catalyst and route for the poly(dimethylsiloxane) synthesis, and trial experiments were conducted to verify the successful synthesis of the intended polymer compositions. Then, a series of APT–PDMS oligomers were synthesized with an automated combinatorial high‐throughput synthesis system to cover a molecular weight range of 2500–50,000 g/mol. Trial PCL—PDMS–PCL triblock copolymers were synthesized with the automated reactor system and characterized in detail with rapid gel permeation chromatography, high‐throughput Fourier transform infrared, nuclear magnetic resonance, and differential scanning calorimetry. Finally, two library synthesis experiments were carried out in which the lengths of both the poly(dimethylsiloxane) and poly(?‐caprolactone) blocks in the PCL—PDMS–PCL triblock copolymers were varied. The results obtained from these experiments demonstrated that it was possible to synthesize libraries of well‐defined APT–PDMS oligomers and PCL—PDMS–PCL triblock copolymers with an automated high‐throughput system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4880–4894, 2006     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Effect of mixing conditions on the morphology and properties of polystyrene/polyethylene blends compatibilized with styrene–butadiene block copolymers

The effect of mixing conditions on the morphology, molten‐state viscoelastic properties, and tensile impact strength of polystyrene/polyethylene (80/20) blends compatibilized with styrene–butadiene block copolymers containing various numbers and lengths of blocks was studied. Under all mixing conditions, an admixture of a styrene–butadiene block copolymer led to a finer phase structure and to an increase in the dynamic viscosity, storage modulus, and tensile impact strength. The effects were stronger for S–B diblock with a short styrene block than for S–B–S–B–S pentablock with long styrene blocks (where S represents styrene and B represents butadiene). For all blends mixed longer than 2 min, the mixing time had only a small effect on their morphology and properties. Surprisingly, the localization of S–B diblock copolymers was strongly dependent on the rate of mixing. The mixing rate had a nonnegligible effect on the viscoelastic properties of the compatibilized blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 609–622, 2003     

Phase diagrams of poly(dimethylsiloxane) and 5CB blends

The phase diagrams of poly(dimethylsiloxane) (PDMS) and 4‐cyano‐4′‐n‐pentyl‐biphenyl (5CB) mixtures are studied for two systems of different molecular weights of the polymer. The experimental diagrams are established by polarized optical microscopy (POM), and analyzed using a combination of the Flory–Huggins theory of isotropic mixing and the Maier–Saupe theory of nematic order. The results are compared with those of polystyrene (PS) and 4‐cyano‐4′‐n‐octyl‐biphenyl (8CB) with analogous molecular weight of the polymer. This investigation could be useful for the choice of systems in electro‐optical devices. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 581–588, 2001