Stainless steel modified with poly(ethylene glycol) can prevent protein adsorption but not bacterial adhesion

The surface of AISI 316 grade stainless steel (SS) was modified with a layer of poly(ethylene glycol) (PEG) (molecular weight 5000) with the aim of preventing protein adsorption and bacterial adhesion. Model SS substrates were first modified to introduce a very high density of reactive amine groups by the adsorption of branched poly(ethylenimine) (PEI) from water. Methoxy-terminated aldehyde-poly(ethylene glycol) (M-PEG-CHO) was then grafted onto the PEI layers using reductive amination at the lower critical solution temperature (LCST) of the PEG in order to optimize the graft density of the linear PEG chains. The chemical composition and uniformity of the surfaces were determined using X-ray photoelectron spectroscopy (XPS) and time-of-flight static secondary ion mass spectrometry (ToF-SSIMS) in the imaging mode. The effects of PEI concentration and different substrate pre-cleaning methods on the structure and stability of the final PEG layer was examined. Piranha solution proved to be the most effective method for removing adventitious hydrocarbon contamination, compared to cleaning with ultrasonication in organic solvents, and was the SS substrate that produced the most stable and thickest PEI layer. The surface density of PEI was shown to increase with increasing PEI concentration (up to 30 mg/ml), as determined from XPS measurements, and subsequently produced the PEG layer with the highest density of attached chains. In model experiments using β-lactoglobulin no protein adsorption was detected on the optimized PEG surface as determined by XPS and ToF-SSIMS analysis. However, neither the adhesion of a Gram-negative (Pseudomonas sp.) nor a Gram-positive (Listeria monocytogenes) bacterium was affected by the coating as equal numbers adhered to all surfaces tested. Our results show that preventing protein adsorption is not a prerequisite stopping bacterial adhesion, and that other mechanisms most likely play a role.     

Poly(acrylic acid)-poly(ethylene glycol) layers on positively charged surface coatings: molecular structure, protein resistance, and application to single protein deposition

A new copolymer (PAA-PEG2000) has been designed, consisting of a negatively charged poly(acrylic acid) (PAA) backbone to which poly(ethylene glycol) (PEG) side chains with a molecular weight of about 2 kDa were grafted in a molecular ratio of 3:10. It readily adsorbs to positively charged surfaces and may be considered to be the anionic counterpart of PEG-grafted poly(l-lysine) (PLL-PEG), which was first described by Kenausis et al. and is widely used to render negatively charged surfaces protein-resistant. The synthesis of PAA-PEG2000 can be carried out in aqueous solution at room temperature and does not require any sophisticated techniques such as handling in an inert gas atmosphere. Using ellipsometry and infrared reflection absorption spectroscopy (IRRAS), the film structure has been carefully analyzed for copolymer adsorption onto three different positively charged surfaces, namely, thin layers of poly(allylamine) (PAH), poly(ethyleneimine) (PEI) and (3-aminopropyl)triethoxysilane (APTES). Besides the film thickness, the conformation of the PEG chains and their orientation with respect to the surface normal appear to be important parameters for the protein resistance of the films. Although PAA-PEG2000 adsorbed to PAH and PEI renders the surfaces inert, only partial protein resistance has been observed if the copolymer is deposited on APTES. In a model application, we have generated heterogeneous surfaces composed of isolated small Au nanoparticles (AuNP's) embedded in a protein-resistant layer of PAA-PEG2000 and demonstrated that the AuNP's can serve as adsorption sites for single protein species. In the future, these nanopatterned surfaces may be used for the investigation of isolated proteins.     

An aqueous-based surface modification of poly(dimethylsiloxane) with poly(ethylene glycol) to prevent biofouling

We report a simple modification of poly(dimethylsiloxane) (PDMS) surfaces with poly(ethylene glycol) (PEG) through the adsorption of a graft copolymer, poly(l-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) from aqueous solution. In this approach, the PDMS surface was treated with oxygen plasma, followed by immersion into aqueous solution containing PLL-g-PEG copolymers. Due to the hydroxyl/carboxylic groups generated on the PDMS surface after oxygen plasma, the polycationic PLL backbone is attracted to the negatively charged surface and PEG side chains exhibit an extended structure. The PEG/aqueous interface generated in this way revealed a near-perfect resistance to nonspecific protein adsorption as monitored by means of optical waveguide lightmode spectroscopy (OWLS) and fluorescence microscopy.     

Fabrication and anti-fouling properties of photochemically and thermally immobilized poly(ethylene oxide) and low molecular weight poly(ethylene glycol) thin films

Poly(ethylene oxide) (PEO) and low molecular weight poly(ethylene glycol) (PEG) were covalently immobilized on silicon wafers and gold films by way of the CH insertion reaction of perfluorophenyl azides (PFPAs) by either photolysis or thermolysis. The immobilization does not require chemical derivatization of PEO or PEG, and polymers of different molecular weights were successfully attached to the substrate to give uniform films. Microarrays were also generated by printing polymer solutions on PFPA-functionalized wafer or Au slides followed by light activation. For low molecular weight PEG, the immobilization was highly dependent on the quality of the film deposited on the substrate. While the spin-coated and printed PEG showed poor immobilization efficiency, thermal treatment of the PEG melt on PFPA-functionalized surfaces resulted in excellent film quality, giving, for example, a grafting density of 9.2×10(-4)?(-2) and an average distance between grafted chains of 33? for PEG 20,000. The anti-fouling property of the films was evaluated by fluorescence microscopy and surface plasmon resonance imaging (SPRi). Low protein adsorption was observed on thermally-immobilized PEG whereas the photoimmobilized PEG showed increased protein adsorption. In addition, protein arrays were created using polystyrene (PS) and PEG based on the differential protein adsorption of the two polymers.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Surface presentation of bioactive ligands in a nonadhesive background using DOPA-tethered biotinylated poly(ethylene glycol)

We have developed surfaces for the selective presentation of biotinylated peptides and proteins in a background that resists nonspecific protein adsorption; controlled amounts of biotinylated poly(ethylene glycol) (MW 3400 Da; PEG3400) anchored to titanium-dioxide-coated surfaces via an adhesive tri-peptide sequence of L-3,4-dihydroxyphenylalanine (DOPA3-PEG3400-biotin; DPB) were incorporated within a DOPA3-PEG2000 background. Using optical waveguide lightmode spectroscopy, we found that the amounts of sequentially adsorbed NeutrAvidin and singly biotinylated molecules increased proportionally with the amount of DPB in the surface. Biotinylated peptides (MW approximately 2000 Da) were able to fill all three of the remaining avidin-binding sites, while only one molecule of biotinylated PEG5000 or stem cell factor bound to each avidin. The resulting biotin-avidin-biotin linkages were stable for prolonged periods under continuous perfusion, even in the presence of excess free biotin. Hematopoietic M07e cells bound to immobilized peptide ligands for alpha5beta1 (cyclic RGD) and alpha4beta1 (cylic LDV) integrins in a DPB-dose-dependent manner, with near-maximal binding to cylic LDV for surfaces containing 1% DPB. Multiple ligands were adsorbed in a controlled manner by incubating NeutrAvidin with the respective ligands in the desired molar ratio and then adding the resulting complexes to DPB-containing surfaces. Cell adhesion to surfaces containing both cylic LDV and cyclic RGD increased in an additive manner compared to that for the individual ligands. The bioactivity of adsorbed biotinylated stem cell factor was retained, as demonstrated by DPB-dose-dependent M07e cell adhesion and ERK1/2 activation.     

Incorporation of an abnormally high amount of poly(ethylene glycol) into poly(ethylene terephthalate) during tensile drawing in liquid media

Tensile drawing of PET via the mechanism of solvent crazing in adsorption-active media containing poly(ethylene glycol) with M < 1 × 10⁶ is accompanied by their penetration into the porous structure of the matrix polymer. In this case, the amount of PEG in PET exceeds its concentration calculated on the assumption that the porous structure is filled with the polymer solution. This excess is evidently due to the adsorption of PEG on the highly developed surface of crazes.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Specific adsorption of histidine-tagged proteins on silica surfaces modified with Ni2+/NTA-derivatized poly(ethylene glycol)

Silica surfaces modified with nitrilotriacetic acid (NTA)-polyethylene glycol (PEG) derivatives were used to immobilize hexahistidine-tagged green fluorescent protein (His6-GFP), biotin/streptavidin-AlexaFluor555 (His6-biotin/SA-AF), and gramicidin A-containing vesicles (His6-gA). Three types of surface-reactive PEG derivatives-NTA-PEG3400-Si(OMe)3, NTA-PEG3400-vinylsulfone, and mPEG5000-Si(OMe)3 (control)-were grafted onto silica and tested for their ability to capture His6-tag species via His6/Ni2+/NTA chelation. The composition and thicknesses of the PEG-modified surfaces were characterized using X-ray photoelectron spectroscopy, contact angle, and ellipsometry. Protein capture efficiencies of the NTA-PEG-grafted surfaces were evaluated by measuring fluorescence intensities of these surfaces after exposure to His6-tag species. XPS and ellipsometry data indicate that surface adsorption occurs via specific interactions between the His6-tag and the Ni2+/NTA-PEG-grafted surface. Protein immobilization was most effective for NTA-PEG3400-Si(OMe)3-modified surfaces, with maximal areal densities achieved at 45 pmol/cm2 for His6-GFP and 95 fmol/cm2 for His6-biotin/SA-AF. Lipid vesicles containing His6-gA in a 1:375 gA/lipid ratio could also be immobilized on Ni2+/NTA-PEG3400-Si(OMe)3-modified surfaces at 0.5 mM total lipid. Our results suggest that NTA-PEG-Si(OMe)3 conjugates may be useful tools for immobilizing His6-tag proteins on solid surfaces to produce protein-functionalized surfaces.     

Conformational characteristics of poly(ethylene phthalate)s

The conformational characteristics, as embodied in the unperturbed mean‐square end‐to‐end distances (〈r²〉_o) and the characteristic ratios of the dimensions [C_n = 〈r²〉_o/(n〈l²〉] are calculated for the para, meta, and ortho isomers of poly(ethylene phthalate)s: poly(ethylene terephthalate) (PET), poly(ethylene isophthalate) (PEI), and poly(ethylene phthalate) (PEP), respectively. Although each of these isomeric and partially aromatic polyesters has identical permissible conformations available to their ethylene glycol fragments, their connections through the ester bonds to the phenyl rings are quite distinct. In addition, for the ortho isomer (PEP), the close spatial proximity of the ester groups bonded to the same phenyl ring results in an interdependence of their orientations with respect to each other and the phenyl ring to which they are attached, unlike the independent orientations of ester groups in the para and meta isomers (PET and PEI). Conformational energy calculations, dependent on the orientation of the ester groups in PEP, are used to characterize their rotational interdependence to modify the rotational isomeric state (RIS) conformational models for PET and PEI and thereby obtain an RIS model appropriate for PEP. This leads to calculated relative dimensions (〈r²〉_o) of 1.0:0.70:0.37 PET:PEI:PEP and characteristic ratios [C_n = 〈r²〉_o/(n〈l²〉)] of 4.13:4.67:2.49 PET:PEI:PEP. These results are discussed in an effort to obtain some understanding of the inherent static (or equilibrium) and dynamic flexibilities of the isomeric poly(ethylene phthalate)s. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1254–1260, 2002     

Surface immobilization of poly(ethylene oxide): Structure and properties

We covalently immobilized poly(ethylene oxide) (PEO) chains onto a fluorinated ethylene propylene copolymer (FEP) surface. On the FEP surface, aldehyde groups were first deposited by plasma polymerization of acetaldehyde or acrolein. Then, amino‐PEO chains were immobilized through Schiff base formation, which was followed by reduction stabilization with sodium cyanoborohydride. The PEO‐grafted polymer surfaces thus prepared were characterized by X‐ray photoelectron spectroscopy (XPS), atomic force microscopy, contact‐angle measurements, and protein adsorption. The dramatic increase in the C O intensity of the high‐resolution XPS C 1s spectrum, together with an overall increase in oxygen content, indicated the successful attachment of PEO chains onto the acetaldehyde plasma surfaces. The amount of grafted PEO chains depended on the superfacial density of the plasma‐generated aldehyde groups. The grafted monoamino‐PEO chains formed a brushlike structure on the polymer surface, whereas the bisamino‐PEO chains predominately adopted a looplike conformation. The PEO surface had a regular morphology with greater roughness than the aldehyde surface underneath. Surface hydrophilicity increased with the grafting of PEO. Also, the bisamino‐PEO‐grafted surface had slightly higher surface hydrophilicity than its monoamino‐PEO counterpart. These PEO coatings reduced fibrinogen adsorption by 43% compared with the substrate FEP surface. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2323–2332, 2000     

Dense passivating poly(ethylene glycol) films on indium tin oxide substrates

We describe the formation and characterization of surface-passivating poly(ethylene glycol) (PEG) films on indium tin oxide (ITO) glass substrates. PEG chains with a molecular weight of 2000 and 5000 D were covalently attached to the substrates in a systematic approach using different coupling schemes. The coupling strategies included the direct grafting with PEG-silane, PEG-methacrylate, and PEG-bis(amine), as well as the two-step functionalization with aldehyde-bearing silane films and subsequent coupling with PEG-bis(amine). Elemental analysis by X-ray photoelectron spectroscopy (XPS) confirmed the successful surface modification, and XPS and ellipsometry provided values for film thicknesses. XPS and ellipsometry thickness values were almost identical for PEG-silane films but differed by up to 400% for the other PEG layers, suggesting a homogeneous layer for PEG-silane but an inhomogeneous distribution for other PEG coatings on the molecularly rough ITO substrates. Atomic force microscopy (AFM) and water contact angle goniometry confirmed the different degrees of surface homogeneity of the polymer films, with PEG-silane reducing the AFM rms surface roughness by 50% and the water contact angle hysteresis by 75% compared to uncoated ITO. The ability of the PEG layers to passivate the substrate against the nonspecific adsorption of biopolymers was tested using fluorescence-labeled immunoglobulin G and DNA oligonucleotides in combination with fluorescence microscopy. The results indicate a positive relationship between film density and homogeneity on one hand and the ability to passivate against biopolymer adhesion on the other hand. The most homogeneous layers prepared with PEG-silane reduced the nonspecific adsorption of fluorescence-labeled DNA by a factor of 300 compared to uncoated ITO. In addition, the study finds that the ratio of film thicknesses derived by ellipsometry and XPS is a useful parameter to quantify the structural integrity of PEG layers on molecularly rough ITO surfaces. The findings may be applied to characterize PEG or other polymeric films on similarly coarse substrates.     

Control of specific attachment of proteins by adsorption of polymer layers

This study concerns the design of protein-resistant polymer adsorbed layers for the control of surface binding of biospecific recognition entities. Polymer surface layers were prepared using the adsorption of poly(allylamine hydrochloride) (PAH), poly(l-lysine) (PL), and branched and linear polyethyleneimine (PEI) and further modified by the covalent attachment of biotin for specific avidin attachment. The adsorption of PAH, PL, and PEI on silicon substrates was studied as a function of pH and ionic strength using ellipsometry. Average dry layer thicknesses of approximately 10, approximately 5, approximately 9, and approximately 3 A (+/-1 A) were obtained when polymer adsorption occurred from solutions at pH 9.5 that contained 0.5 M NaCl for PAH, PL, branched PEI, and linear PEI, respectively. These polymers showed significant differences in their efficiency to suppress nonspecific avidin adsorption. At low ionic strength, avidin adsorption occurred on all polymer-coated surfaces at basic pH values, despite the same positive electrostatic charge for protein globules and the surface. Though the net electrostatic repulsion between avidin molecules and branched PEI was efficiently screened in a protein solution of pH 7 and 0.15 M NaCl, branched-PEI coatings of high molecular weight were unique in their ability to provide avidin-resistant surfaces as a result of steric hindrance from the branched architecture of adsorbed polymer chains. All polymers studied were effective in suppressing avidin adsorption at pH 3 as a result of protonation of the avidin surface functional groups at this pH. Branched-PEI-coated surfaces were also effective for the suppression of smaller positively charged proteins such as lysozyme and ribonuclease A at pH 7 and 0.15 M NaCl. They were also resistant to the adsorption of negatively charged proteins such as BSA and fibrinogen at pH 7 and 0.75 M NaCl. Furthermore, by using PEI-modified protein-repellent surfaces, selective binding of avidin was achieved to surface-bound silver nanoparticles, which should provide a promising application for the label-free detection of biological species using surface-enhanced Raman scattering (SERS).     

Enhanced crystallization behaviors of poly(ethylene terephthalate) via adding expanded graphite and poly(ethylene glycol)

A compound additive system consisting of expanded graphite (EG) and poly(ethylene glycol) (PEG) was designed to enhance the crystallization of poly(ethylene terephthalate) (PET). In this additive system, EG acted as a heterogeneous nucleating agent to reduce energy barrier for nucleation, while PEG played as plasticizer to improve mobility of PET chains. Simultaneously adding EG and PEG resulted in faster crystallization kinetics than the cases of solely adding EG or PEG in both of non-isothermal and isothermal crystallization processes, indicating a synergistic effect of EG and PEG on enhancing PET crystallization. However, for non-isothermal crystallization process, in which crystallization occurred from a cooling melt, EG played a dominant role. As to isothermal crystallization process where crystallization took place in a super-cooling state, PEG seemed to be more important. Moreover, the chain conformation change among the semi-crystalline PET specimens was ascertained by Fourier transform infrared spectroscopy.     

Protein adhesion on silicon-supported hyperbranched poly(ethylene glycol) and poly(allylamine) thin films

Hyperbranching poly(allylamine) (PAAm) and poly(ethylene glycol) (PEG) on silicon and its effect on protein adhesion was investigated. Hyperbranching involves sequential grafting of polymers on a surface with one of the components having multiple reactive sites. In this research, PAAm provided multiple amines for grafting PEG diacrylate. Current methodologies for generating PEG surfaces include PEG-silane monolayers or polymerized PEG networks. Hyperbranching combines the nanoscale thickness of monolayers with the surface coverage afforded by polymerization. A multistep approach was used to generate the silicon-supported hyperbranched polymers. The silicon wafer surface was initially modified with a vinyl silane followed by oxidation of the terminal vinyl group to present an acid function. Carbodiimide activation of the surface carboxyl group allowed for coupling to PAAm amines to form the first polymer layer. The polymers were hyperbranched by grafting alternating PEG and PAAm layers to the surface using Michael addition chemistry. The alternating polymers were grafted up to six total layers. The substrates remained hydrophilic after each modification. Static contact angles for PAAm (32-44 degrees) and PEG (33-37 degrees) were characteristic of the corresponding individual polymer (30-50 degrees for allylamine, 34-42 degrees for PEG). Roughness values varied from approximately 1 to 8 nm, but had no apparent affect on protein adhesion. Modifications terminating with a PEG layer reduced bovine serum albumin adhesion to the surface by approximately 80% as determined by ELISA and radiolabel binding studies. The hyperbranched PAAm and PEG surfaces described in this paper are nanometer-scale, multilayer films capable of reducing protein adhesion.     

Preparation and characterization of nonfouling polymer brushes on poly(ethylene terephthalate) film surfaces

In this study, a surface grafting of nonfouling poly(ethylene glycol) methyl ether acrylate (PEGMA) on poly(ethylene terephthalate) (PET) was carried out via surface-initiated atom-transfer radical polymerization (SI-ATRP) to improve hemocompatibility of polymer based biomaterials. To do this, the coupling agent with hydroxyl groups for the ATRP initiator was first anchored on the surface of PET films using photochemical method, and then these hydroxyl groups were esterified by bromoisobutyryl bromide, from which PET with various main chain lengths of PEGMA was prepared. The structures and properties of modified PET surfaces were investigated using water contact angle (WAC), ATR-FTIR, X-ray photoelectron spectroscopy (XPS) and Atomic force microscopy (AFM). The molecular weights of the free polymer from solution were determined by gel permeation chromatography (GPC). These results indicated that grafting of PEGMA on PET film is a simple way to change its surface properties. The protein adsorption resistance on the surfaces of PET was primarily evaluated by an enzyme-linked immunosorbent assay (ELISA). The result demonstrated that the protein adsorption could be well suppressed by poly(PEGMA) brush structure on the surface of PET. This work provides a new approach for polymers to enhance their biocompatibility.     

Crystallization of poly(ethylene terephthalate–co–isophthalate)

Melt crystallization behaviors of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐isophthalate) (PETI) containing 2 and 12 mol % of noncrystallizable isophthalate components were investigated. Differential scanning calorimetry (DSC) isothermal results revealed that the introduction of 2 mol % isophthalate into PET caused a change of the crystal growth process from a two‐dimensional to a three‐dimensional spherulitic growth. The addition of more isophthalate up to 12 mol % into the PET structure induced a change in the crystal growth from a three‐dimensional to a two‐dimensional crystal growth. DSC heating scans after completion of isothermal crystallization at various T_c's showed three melting endotherms for PET and four melting endotherms for PETI‐2 and PETI‐12. The presence of an additional melting endotherm is attributed to the melting of copolyester crystallite composed of ethylene glycol, tere‐phthalate, and isophthalate (IPA) or the melting of molecular chains near IPA formed by melting the secondary crystallite T_m (I) and then recrystallizing during heating. Analyses of both Avrami and Lauritzen‐Hoffman equations revealed that PETI containing 2 mol % of isophthalate had the highest Avrami exponent n, growth rate constant G_o, and product of lateral and end surface free energies σσ_e. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2515–2524, 2000     

Simultaneous tailoring of surface topography and chemical structure for controlled wettability

Wettability was controlled in a rational manner by individually and simultaneously manipulating surface topography and surface chemical structure. The first stage of this research involved the adsorption of charged submicrometer polystyrene latex particles to oppositely charged poly(ethylene terephthalate) (PET) film samples to form surfaces with different topographies/roughness; adsorption time, solution pH, solution ionic strength, latex particle size, and substrate charge density are external variables that were controlled. The introduction of discrete functional groups to smooth and rough surfaces through organic transformations was carried out in the second stage. Amine groups (-NH(2)) and alcohol groups (-OH) were introduced onto smooth PET surfaces by amidation with poly(allylamine) and adsorption with poly(vinyl alcohol) (PVOH), respectively. On latex particle adsorbed surfaces, a thin layer of gold was evaporated first to prevent particle redistribution before chemical transformation. Reactions with functionalized thiols and adsorption with PVOH on patterned gold surfaces successfully enhanced surface hydrophobicity and hydrophilicity. Particle size and biomodal particle size distribution affect both hydrophobicity and hydrophilicity. A very hydrophobic surface exhibiting water contact angles of 150 degrees /126 degrees (theta(A)/theta(R)) prepared by adsorption of 1-octadecanethiol and a hydrophilic surface with water contact angles of 18 degrees /8 degrees (theta(A)/theta(R)) prepared by adsorption of PVOH were prepared on gold-coated surfaces containing both 0.35 and 0.1 microm latex particles. The combination of surface topography and surface-chemical functionality permits wettability control over a wide range.     

The behavior of poly(amino acids) containing l‐cysteine and their block copolymers with poly(ethylene glycol) on gold surfaces

Poly(ethylene glycol) (PEG) is often used to biocompatibilize surfaces of implantable biomedical devices. Here, block copolymers consisting of PEG and l ‐cysteine‐containing poly(amino acid)s (PAA's) were synthesized as polymeric multianchor systems for the covalent attachment to gold surfaces or surfaces decorated with gold nanoparticles. Amino‐terminated PEG was used as macroinitiator in the ring‐opening polymerization, (ROP), of respective amino acid N‐carboxyanhydrides (NCA's) of l ‐cysteine (l ‐Cys), l ‐glutamate (l ‐Glu), and l ‐lysine (l ‐Lys). The resulting block copolymers formed either diblock copolymers, PEG‐b‐p(l ‐Glu_x‐co‐l ‐Cys_y) or triblock copolymers, PEG‐b‐p(l ‐Glu)_x‐b‐p(l ‐Cys)_y. The monomer feed ratio matches the actual copolymer composition, which, together with high yields and a low polydispersity, indicates that the NCA ROP follows a living mechanism. The l ‐Cys repeat units act as anchors to the gold surface or the gold nanoparticles and the l ‐Glu repeat units act as spacers for the reactive l ‐Cys units. Surface analysis by atomic force microscopy revealed that all block copolymers formed homogenous and pin‐hole free surface coatings and the phase separation of mutually immiscible PEG and PAA blocks was observed. A different concept for the biocompatibilization of surfaces was followed when thiol‐terminated p(l ‐Lys) homopolymer was first grafted to the surface and then covalently decorated with HOOC‐CH₂‐PEG‐b‐p(Bz‐l ‐Glu) polymeric micelles. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 248–257     

Glass surfaces grafted with high-density poly(ethylene glycol) as substrates for DNA oligonucleotide microarrays

Surfaces carrying a dense layer of poly(ethylene glycol) (PEG) were prepared, characterized, and tested as substrates for DNA oligonucleotide microarrays. PEG bis(amine) with a molecular weight of 2000 was grafted onto silanized glass slides bearing aldehyde groups. After grafting, the terminal amino groups of the PEG layer were derivatized with the heterobifunctional cross-linker succinimidyl 4-[p-maleimidophenyl]butyrate to permit the immobilization of thiol-modified DNA oligonucleotides. The stepwise chemical modification was validated with X-ray photoelectron spectroscopy. Goniometry indicated that the PEG grafting procedure reduced surface inhomogeneities present after the silanization step, while atomic force microscopy and ellipsometry confirmed that the PEG layer was dense and monomolecular. Hybridization assays using DNA oligonucleotides and fluorescence imaging showed that PEG grafting improved the yield in hybridization 4-fold compared to non-PEGylated maleimide-derivatized surfaces. In addition, the PEG layer reduced the nonspecific adsorption of DNA by a factor of up to 13, demonstrating that surfaces with a dense PEG layer represent suitable substrates for DNA oligonucleotide microarrays.