Study on δ‐form complex in syndiotactic polystyrene–organic molecules systems. IV. Formation of complexes with a mixture of solvents and structural changes during the sorption of solvents by syndiotactic polystyrene mesophase membranes

The syndiotactic polystyrene (sPS) δ form was crystallized from mixtures with different compositions of p‐chlorotoluene–chlorobenzene (p‐CT–CB) and p‐chlorotoluene–1,1,2‐trichloroethane (p‐CT–TCE). The presence of the δ form and TTGG helical conformation was confirmed by Fourier transform infrared and wide‐angle X‐ray diffraction (WAXD) analyses. In sPS/p‐CT–CB and sPS/p‐CT–TCE δ‐form membranes, the relative absorbance (RA) of the p‐chlorotoluene (p‐CT) solvent peak was very high even at very low concentrations of p‐CT in comparison with the RA of higher concentrations of chlorobenzene (CB) or 1,1,2‐trichloroethane (TCE) in the mixtures. However, the RAs of both CB and TCE solvent peaks decreased with decreasing concentrations of CB and TCE in the mixtures. A negligible decrease in the RA of the TTGG helical content was observed with a decreasing concentration of CB or TCE. The WAXD results showed that the 2θ peak positions of the [010] and [ 10] planes of the sPS/p‐CT–CB and sPS/p‐CT–TCE δ‐form membranes appeared in the same position and were almost equal to those of the sPS–p‐CT δ‐form membrane. The mesophases of the sPS–p‐CT [p‐CT (A‐M)] and sPS–TCE [TCE (A‐M)] membranes were used for the sorption studies with different concentrations of various solvents. The sorption amount of aromatic solvents by both p‐CT (A‐M) and TCE (A‐M) mesophase membranes was higher than that of aliphatic solvents, regardless of the size, shape, and nature of the molecular cavity. The 2θ peak of the [010] plane of the sPS membranes slowly approached the original δ‐form value when the sPS mesophase membranes were immersed in various solvents of different concentrations for 48 h. The shifting of the 2θ peak of the [010] plane to the original δ form depended on the nature and concentration of the immersion solvents. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2380–2387, 2005     

Structure and properties of the mesophase of syndiotactic polystyrene—III. Selective sorption of the mesophase of syndiotactic polystyrene

Syndiotactic polystyrene (sPS) has various crystalline forms such as α, β, γ, and δ forms, and a mesophase depending on the preparation method. In this study, we focused on the mesophase with the molecular cavity of sPS, which is obtained by step‐wise extraction of the guest molecules from the sPS δ form. To prepare the mesophase containing different shapes and sizes of the cavity, two kinds of the sPS δ form membrane cast from either toluene or chloroform solution were first prepared and then the guest molecules were removed by a step‐wise extraction method using acetone and methanol. We could succeed in the preparation of two kinds of mesophase with different shapes and sizes of the molecular cavity. Either toluene or chloroform vapor sorption to the sPS mesophase membranes was examined at 25 °C. Sorption analysis indicates that the mesophase with large molecular cavities can mainly sorb large molecules; on the other hand, the mesophase with small cavities can sorb only the small molecules, and is unable to sorb a large amount of large molecule because the cavity was too small to sorb the large molecules. Therefore, the sPS mesophase membrane has sorption selectivity based on the size of the molecular cavity. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 238–245, 2004     

Structure and properties of the δ‐form and mesophase of syndiotactic polystyrene membranes prepared from different organic solvents

Syndiotactic polystyrene (sPS) membranes were prepared with different organic solvent systems and compared to get the information about the δ‐form complexing behavior of sPS. Further, the guest molecules included in the clathrate δ form of sPS are removed by stepwise extraction method. The conformational changes during the TTGG helical formation of sPS/organic solvent systems have been identified by FTIR spectroscopy, and it was concluded that the TTGG helices were constructed in regular sequences, which depends on the nature of the respective solvents. The TTGG content in the mesophase is found to be increased by removing the guest molecules. The structural changes of sPS/organic solvent systems have been characterized by WAXD analysis. Moreover, the different clathrate structures were found and showed the different crystalline reflections in the WAXD profiles, which are significantly changed with the kind of guest solvent included in sPS. The content of solvents in the clathrated sPS and the desorption temperatures were determined by thermal analysis. The resulted mesophase of sPS membrane contains the nanoporous molecular cavities that depend on the size of the guest molecule. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1873–1880, 2005     

Structure and properties of the mesophase of syndiotactic polystyrene. I. Effect of casting conditions on the preparation of the mesophase

A syndiotactic polystyrene–toluene solution was cast under two different casting conditions to obtain the δ form. A systematic study of its conformational transition, thermal behavior, and structural transformation as functions of the annealing temperature and time was performed. Spectroscopic studies revealed the content of its helical conformations and its retention up to 190 °C. Thermal analyses showed a significant difference in the transformation from the γ form to the α form. The retention of the intermediate emptied clathrate form (mesophase) of the conformational order for a longer duration (from 120 to 180 °C) in a syndiotactic polystyrene membrane cast at room temperature was confirmed by X‐ray diffraction analysis. On the basis of the experimental results in this work, the transition mechanism is discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 530–536, 2002; DOI 10.1002/polb.10120     

Effect of the premelting temperature and sample thickness on the polymorphic behavior of syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods and differential scanning calorimetry thermal analysis have been used to investigate the structural changes of syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay nanocomposites have been prepared by the mixing of sPS polymer solutions with organically modified montmorillonite. X‐ray diffraction data and differential scanning calorimetry results indicate that the dominating crystal forms and their relative fractions in sPS and sPS/clay nanocomposites are different for various premelting temperatures (T_max's). Higher T_max's favor the formation of the thermodynamically more stable β‐crystalline form, and its relative fraction has been obtained from the X‐ray diffraction data in the range of 11.5–13°. The intensity of the X‐ray diffraction data in the range of 11.5–13° decreases as the thickness of sPS/clay nanocomposites decreases from 150 to 20 μm. At the same time, the intensity of the X‐ray data in the range of 6–7° becomes sharper as the thickness of sPS/clay nanocomposites decreases. The calculation ratio based on the peak intensities at 6.2 and 6.8° for sPS/clay nanocomposites of equal thickness and crystallinity in the pure β and α forms has also been determined in this study. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1730–1738, 2003     

Effects of the oriented mesophase on the cold crystallization of syndiotactic polystyrene and its blend with poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The effects of molecular orientation on the crystallization and polymorphic behaviors of syndiotactic polystyrene (sPS) and sPS/poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) blends were studied with wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. The oriented amorphous films of sPS and sPS/PPO blends were crystallized under constraint at crystallization temperatures ranging from 140 to 240°C. The degree of crystallinity was lower in the cold‐crystallized oriented film than in the cold‐crystallized isotropic film. This was in contrast to the case of the cold crystallization of other polymers such as poly(ethylene terephthalate) and isotactic polystyrene, in which the molecular orientation induced crystallization and accelerated crystal growth. It was thought that the oriented mesophase was obtained in drawn films of sPS and that the crystallization of sPS was suppressed in that phase. The WAXD measurements showed that the crystal phase was more ordered in an sPS/PPO blend than in pure sPS under the same annealing conditions. The crystalline order recovered in the cold‐crystallized sPS/PPO blends in comparison with the cold‐crystallized pure sPS because of the decrease in the mesophase content. The crystal forms depended on the crystallization temperature, blend composition, and molecular orientation. Only the α′‐crystalline form was obtained in cold‐crystallized pure sPS, regardless of molecular orientation, whereas α′, α″, and β′ forms coexisted in the cold‐crystallized sPS/PPO blends prepared at higher crystallization temperatures (200–240°C). The β′‐form content was much lower in the oriented sPS/PPO blend than in the isotropic blend sample at the same temperature and composition. It was concluded that the oriented mesophase suppressed the crystallization of the stable β′ form more than that of the metastable α′ and α″ forms during the cold crystallization of sPS/PPO blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1665–1675, 2003     

Structure and properties of the mesophase of syndiotactic polystyrene. II. Effect of stepwise extraction on the preparation of the mesophase

In this study, a novel stepwise extraction method has been examined. The guest molecules housed between the helices of the clathrate δ form of syndiotactic polystyrene can be removed completely with this method. A systematic study of the preparation of a solvent‐free mesophase (emptied clathrate) membrane, its helical and residual solvent contents, and its structural transformations has been performed. In this first attempt, an enhancement in the TTGG helical content has been observed in the extracted membrane, and a conceptual mechanism is proposed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 269–273, 2003     

DGEBA monomer as a solvent for syndiotactic polystyrene

Syndiotactic polystyrene (sPS) has to be processed at high temperatures (i.e. >290°C due to its melting point of 270°C), which approaches its degradation temperature. We aim to facilitate the processing of sPS by lowering its melt temperature and viscosity with a curable epoxy/amine model system as reactive solvent, which will result in a thermoplastic-thermoset polymer blend. As a first step we therefore investigated the melting behaviour of sPS in epoxy monomer, established its phase diagram, and investigated the crystalline form of sPS in these mixtures. DGEBA epoxy monomer is found to be a solvent for syndiotactic polystyrene at temperatures above 220°C. The DGEBA-sPS phase diagram was established by means of DSC, on the basis of crystallization and melting peaks. The form of the curve in the phase diagram indicates that DGEBA is a poor solvent for sPS. In WAXS studies of blends only the β crystalline form was detected, not the δ form, thus no sPS-DGEBA polymer-solvent compounds (clathrates) were detected. However, DGEBA can still serve as a monomer for improved processing as it depresses the crystallization temperature by 20 to 60 K upon addition of 20 to 90 wt% DGEBA respectively, while a 16 to 45 K melting peak depression can be observed by adding 20 to 90 wt% DGEBA.     

Vapor sorption in emptied clathrate samples of syndiotactic polystyrene

The analysis of chloroform vapor sorption at 35°C in semicrystalline syndiotactic polystyrene samples shows remarkably different sorption isotherms, depending on the crystalline form of the samples. In particular, “emptied” clathrate (“emptied” δ form) samples are characterized by higher equilibrium sorption levels and the differences are particularly relevant for low vapor activities. Moreover, sorption kinetics detected at a vapor activity equal to 0.5 show that in the case of “emptied” δ form samples the sorption rate is much higher than for the other semicrystalline samples. The larger sorption equilibrium uptakes and sorption rates of the “emptied” δ form samples are essentially due to their ability to absorb chloroform, already for low activities, by clathration in the crystalline phase. The measured equilibrium uptakes and sorption kinetics suggest that “emptied” δ form samples of syndiotactic polystyrene could be suitable for removing polluting chlorinated compounds from vapor and liquid streams. © 1997 John Wiley & Sons, Inc.     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Molecular conformation of syndiotactic polystyrene gel from octadecyl benzoate solution

The molecular chain conformation of the dried gel of syndiotactic polystyrene (sPS) in octadecyl benzoate solution was investigated. sPS gels form rapidly through solid-liquid phase separation. The obtained sPS chains are in the highly ordered all-trans TT skeletal conformation which is different from a twofold TTGG helical conformation that sPS assumes in normal solvents. The size of the solvent molecule is considered to play an important role in the formation of the conformation of sPS in solution.     

Strong diffuse scattering and lamellar morphologies of syndiotactic polystyrene: Polymorphic effects

Syndiotactic polystyrene (sPS) samples melt‐crystallized into neat α″‐ hexagonal and β′‐orthorhombic modifications were prepared at various temperatures thoroughly for extensive morphological studies. The lamellar morphologies of the as‐prepared sPS samples were investigated with small‐angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM). For SAXS measured at 25°C, a barely observed scattering hump was detected for β′‐form sPS, whereas no discernible scattering feature was found for α″‐form sPS because of a small difference in the electron density between the crystalline and amorphous phases. For increased scattering contrast and strength, SAXS was carried out at 150°C so that more reliable morphological parameters would be obtained. In addition to the enhanced scattering peak relevant to the lamellar features, strong diffuse scattering near the beam stop was observed for both α″‐ and β′‐form sPS samples. The contribution of the diffuse scattering at low q regions (where q is the scattering vector) was rather prominent, obscuring the precise position of the scattering peak. On the basis of the Debye–Bueche theory, the strength and inhomogeneity length were derived to render the diffuse scattering. After the subtraction of the diffuse scattering from the observed intensities, scattering intensities exclusively associated with the lamellar features were obtained. Lamellar thicknesses were further derived from the one‐dimensional correlation function of the modified intensities, and a good agreement was reached in comparison with TEM results. From exhaustive TEM observations on the RuO₄‐stained samples, long and parallel lamellae were readily observed in β′‐form sPS. However, relatively irregular packing of lamellar stacks with short lateral dimensions was detected in the as‐prepared α″‐form sPS, leading to the absence of spherulitic birefringence under polarized optical microscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2457–2469, 2003     

Polymorphic behavior in syndiotactic polystyrene/clay nanocomposites

X‐ray diffraction methods were used in an investigation of the structural changes in syndiotactic polystyrene (sPS)/clay nanocomposites. sPS/clay was prepared by the intercalation of sPS polymer into layered montmorillonite. Both X‐ray diffraction data and transmission electron microscopy micrographs of sPS/clay nanocomposites indicated that most of the swellable silicate layers were exfoliated and randomly dispersed in the sPS matrix. The X‐ray diffraction data also showed the presence of polymorphism in the sPS/clay nanocomposites. This polymorphic behavior was strongly dependent on the thermal history of the sPS/clay nanocomposites from the melt and on the content of clay in the sPS/clay nanocomposites. Quenching from the melt induced crystallization into the α‐crystalline form, and the addition of montmorillonite probably increased heterophase nucleation of the α‐crystalline form. The effect of the melt crystallization of sPS and sPS/clay nanocomposites at different temperatures on the crystalline phases was also examined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 736–746, 2002     

GAS SORPTION,DIFFUSION AND PERMEATION OF ORDERED POLYMERIC MEMBRANES

He, CO_2, O_2, N_2, CH_4, C_3H_8, and t-C_4H_(10) gas permeability coefficients and diffusion coefficients of poly(4-methylpentene-1) (PMP) with various degrees of crystallization were plotted against the degree of crystallization. The plotdemonstrated a linear relationship. The gas permeability coefficient and diffusion coefficient of pure amorphous and purecrystalline PMPs were evaluated by a linear extrapolation to zero and 100% crystallinity, respectively. The relationshipbetween the diffusion coefficient of crystalline parts of PMP and the kinetic diameter of penetrant gases was discussed.Syndiotactic polystyrene (SPS) could exist as δ form crystals complexed with organic solvents such as benzene, toluene,xylene, and ethylbenzene. The mesophase of SPS is prepared by annealing the δ form of crystalline complexes at a certaintemperature for 1 h. The desorption of solvent during annealing almost does not result in changes of both the conformation ofbackbone chains and the crystal lattice. We could prepare the mesophase containing molecular cavities with the size andshape of the organic solvent molecules. The mesophase could sorb the same solvent after the manner of Langmuir sorption atlow vapor pressure range while this would not be the case for solvents of different size and shape. This suggests a molecularrecognition of organic solvent, and mesophase SPS might be useful for separation membrane and adsorptive material.     

Nonisothermal crystallization behavior of syndiotactic polystyrene/montmorillonite nanocomposites

X‐ray diffraction methods and differential scanning calorimetry were used to investigate the crystalline structure and crystallization kinetics of syndiotactic polystyrene (sPS)/clay nanocomposites. X‐ray diffraction data showed the presence of polymorphism in sPS/montmorillonite (MMT) nanocomposites, which was strongly dependent on the processing conditions (premelting temperature and cooling rate) of the sPS/MMT nanocomposites and on the content of MMT in the sPS/MMT nanocomposites. The α‐crystalline form could be transformed into β‐crystalline forms at higher premelting temperatures. The nonisothermal melt‐crystallization kinetics and melting behavior of the sPS/MMT nanocomposites were also studied at various cooling rates. The correlation of the crystallization kinetics, melting behavior, and crystalline structure of the sPS/MMT nanocomposites was examined. The results indicated that the addition of a small amount of MMT to sPS caused a change in the mechanism of nucleation and the crystal growth of the sPS crystallite. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 560–570, 2003     

Thermal properties and crystalline structure of syndiotactic polystyrene‐based miscible blends

This work examined the effect of the pre‐melting temperature (T_max) on the thermal properties and crystalline structure of four miscible syndiotactic polystyrene (sPS)‐based blends containing 80 wt % sPS. The counterparts for sPS included a high‐molecular‐weight atactic polystyrene [aPS(H)], a medium‐molecular‐weight atactic polystyrene [aPS(M)], a low‐molecular‐weight atactic polystyrene [aPS(L)], and a low‐molecular‐weight poly(styrene‐co‐α‐methyl styrene) [P(S‐co‐αMS)]. According to differential scanning calorimetry measurements, upon nonisothermal melt crystallization, the crystallization of sPS shifted to lower temperatures in the blends, and the shift followed this order of counterpart addition: P(S‐co‐αMS) > aPS(L) > aPS(M) > aPS(H). The change in T_max (from 285 to 315 °C) influenced the crystallization of sPS in the blends to different degrees, depending on the counterpart's molecular weight and cooling rate. The change in T_max also affected the complex melting behaviors of pure sPS and an sPS/aPS(H) blend, but it affected those of the other blends to a lesser extent. Microscopy investigations demonstrated that changing T_max slightly affected the blends' crystalline morphology, but it apparently altered that of pure sPS. Furthermore, the X‐ray diffraction results revealed that the α‐form sPS crystal content in the blends generally decreased with an increase in T_max, and it decreased with a decrease in the cooling rate as well. The blends showed a lower α‐form content than pure sPS; a counterpart of a lower molecular weight more effectively reduced the formation of α‐form crystals. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2798–2810, 2006     

Two‐phase crystallization kinetics of syndiotactic polystyrene

In this work, a two phase crystallization model based on the extension of the Kolmogoroff approach was proposed and verified by comparison with experimental isothermal and nonisothermal crystallization data of Syndiotactic Polystyrene (sPS) in a very wide range of cooling rates, up to 600 °C/s. To investigate the effects of high cooling rate on the sPS crystalline structure, a homemade apparatus was adopted. The morphology in solid samples was analyzed by densitometry, IR spectroscopy, and X‐rays diffraction. The coupling of these techniques allows the determination of the fractions of different crystalline phases. In agreement with melt‐crystallization studies of sPS proposed by different authors, either α and β forms could be produced depending on the thermal history of the sample. Results show that the stable β form is favored for specimens solidified at higher temperature or under low cooling rates, whereas α and mesomorphic forms are favoured at low temperature or high cooling rates. The proposed multiphase crystallization kinetics model successfully described all the range of experimental data. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1757–1766, 2010     

Separation of p‐Divinylbenzene by Selective Room‐Temperature Adsorption Inside Mg‐CUK‐1 Prepared by Aqueous Microwave Synthesis

A new Mg^II‐based version of the porous coordination polymer CUK‐1 with one‐dimensional pore structure was prepared by microwave synthesis in water. Mg‐CUK‐1 is moisture‐stable, thermally stable up to 500 °C, and shows unusual reversible soft‐crystal behavior: dehydrated single crystals of the material selectively adsorb a range of organic molecules at ambient temperature and pressure. Both polar and apolar aromatic compounds, including pyridine, benzene, p‐xylene, and p‐divinylbenzene (p‐DVB), are all readily adsorbed, while other isomers from complex mixtures of xylenes or DVBs are selectively excluded. The solvent‐loaded structures have been studied by single‐crystal X‐ray diffraction. Time‐dependent liquid sorption experiments using commercially available DVB demonstrate a high and rapid selective adsorption of p‐DVB and exclusion of m‐DVB and ethylvinylbenzene isomers.     

Reactive processing of syndiotactic polystyrene with an epoxy/amine solvent system

Syndiotactic polystyrene (sPS) is a new semi-crystalline thermoplastic which is believed to fill the price-performance gap between engineering and commodity plastics. In order to reduce the high processing temperature of sPS (>290°C), an epoxy-amine model system was used as a reactive solvent. Such a processing aid can be used to achieve a 50 to 500 fold lowering of the melt viscosity. When initially homogeneous solutions of sPS in a stoechiometric epoxy-amine mixture are thermally cured, Reaction Induced Phase Separation (RIPS) takes place, leading to phase separated thermoplastic-thermoset polymer blends. We focus our study on low (wt% sPS < 20%) and high concentration blends (wt% sPS > 60%) prepared by two processing techniques (mechanical stirring in a laboratory reactor or internal mixer/ reactive extrusion respectively). These blends have different potential interests. Low concentration blends (sPS domains in an epoxy-amine matrix) are prepared to create new, tunable blend morphologies by choosing the nature of the phase separation process, i.e. either crystallisation followed by polymerization or polymerization followed crystallisation. High concentration blends (sPS matrix containing dispersed epoxy-amine particles after RIPS) are prepared to facilitate the extrusion of sPS. In this case, the epoxy amine model system served as a reactive solvent. The time to the onset of RIPS is in the order of 7-9 min for low concentration blends, while it increases to 20-45 min for high concentration samples, as the reaction rates are substantially slowed down due to lower epoxy and amine concentrations. During the curing reaction the melting temperature of sPS in the reactive solvent mixture evolves back from a depressed value to the level of pure sPS. This indicates a change in the composition of the sPS phase, caused by (complete) phase separation upon reaction. We conclude that our epoxy amine system is suited for reactive processing of sPS, where final properties depend strongly on composition and processing conditions.     

Crystallization kinetics and crystallization behavior of syndiotactic polystyrene/clay nanocomposites

We investigated the effects of montmorillonite (clay) on the crystallization kinetics of syndiotactic polystyrene (sPS) with isothermal differential scanning calorimetry analyses. The clay was dispersed into the sPS matrix via melt blending on a scale of 1–2 nm or up to about 100 nm, depending on the surfactant treatment. For a crystallization temperature of 240 °C, the isothermal crystallization data were fitted well with the Avrami crystallization equation. Crystallization data on the kinetic parameters (i.e., the crystallization rate constant, Avrami exponent, clay content, and clay/surfactant cation‐exchange ratio) were also investigated. Experimental results indicated that the crystallization rate constant of the sPS nanocomposite increased with increasing clay content. The clay played a vital role in facilitating the formation on the thermodynamically more favorable all‐β‐form crystal when the sPS was melt‐crystallized. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2097–2107, 2001