Ultrasonic studies on alkali borate tungstate glasses

Longitudinal and shear ultrasonic wave velocities have been measured in different compositions of the glass system 20Li₂O-(80−x)B₂O₃-xWO₃ (0?x?12.5 mol%), at room temperature and at 4 MHz frequency. Elastic moduli, Debye temperature and Poisson's ratio have been obtained as a function of WO₃ content. Based on FTIR spectroscopy and theoretical bond compression model, quantitative analysis has been carried out in order to obtain more information about the structure of these glasses. The longitudinal ultrasonic wave velocity measurements showed a bend at about 2.5 mol% WO₃ content while shear ultrasonic wave velocity decreased monotonously with an increase of WO₃ content. Elastic moduli values decreased as WO₃ content increased from 0 to 2.5 mol%. Further increase of WO₃ beyond 2.5 mol% increased the elastic moduli values. It is suggested that these behaviours are mainly due to the presence of WO₃ in the network structure of these glasses as a network modifier when WO₃ content is between 0 and 2.5 mol%, and acts as a network former above 2.5 mol%.     

Magnetic and structural properties of CaO–SiO2–P2O5–Na2O–Fe2O3 glass ceramics

Magnetic properties of glass ceramics derived from glasses with composition 41CaO·(52−x)SiO₂·4P₂O₅·xFe₂O₃·3Na₂O (2?x?10 mol% iron oxide (Fe₂O₃)) are reported. Structural investigation revealed the presence of nanocrystalline magnetite phase in the heat-treated samples containing x?2 mol% Fe₂O₃. Magnetic hysteresis cycles of the glass-ceramic samples were obtained with a maximum applied field of ±20 kOe as well as a low field of ±500 Oe, in order to evaluate the potential of these glass ceramics for hyperthermia treatment of cancer. Samples with x>2 mol% of iron oxide exhibited magnetic behavior similar to soft magnetic materials with low coercivity. The evolution of magnetic properties in these samples as a function of iron oxide molar concentration is correlated with the amount and crystallite size of magnetite phase present in them.     

Optical absorption and thermoluminescence studies on LiF-Sb2O3-B2O3 glasses doped with Ni ions

20LiF-(30−x)Sb₂O₃-50B₂O₃:xNiO glasses with the value of x (ranging from 0 to 1.0 mol% in steps of 0.2) were prepared. A number of studies, viz. differential scanning calorimetry, optical absorption, magnetic susceptibility and thermoluminescence, on these glasses were carried out as a function of nickel ion concentration. An anomaly has been observed in all the properties of these glasses when NiO concentration is about 0.6 mol%. The results of these studies were analysed in the light of different environments of nickel ions in the glass network.     

Effect of ZnO on phase emergence, microstructure and surface modifications of calcium phosphosilicate glass/glass-ceramics having iron oxide

The effect of ZnO on phase emergence and microstructure properties of glass and glass-ceramics with composition 25SiO₂-50CaO-15P₂O₅-(10 − x)Fe₂O₃-xZnO (where x = 0, 2, 5, 7 mol%) has been studied. They have been characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Surface modifications of these glass-ceramics in simulated body fluid have been studied using Fourier transform infrared reflection spectroscopy (FTIR), XPS and SEM. Results have shown a decrease in the fraction of non-bridging oxygen with increase in zinc oxide content. Emergence of crystalline phases in glass-ceramics at different heat treatment temperatures was studied using XRD. When glass is heat treated at 800 °C calcium phosphate, hematite and magnetite are developed as major phases in the glass-ceramics samples with ZnO up to 5 mol%. In addition to these, calcium silicate (Ca₃Si₂O₇) phase is also observed when glass is heat treated at 1000 °C. The microstructure of the glass-ceramics heat treated at 800 °C exhibits the formation of nano-size (40-50 nm) grains. On heat treatment at 1000 °C crystallites grow to above 50 nm size and more than one phase are observed in the microstructure. The formation of thin flake-like structure with coarse particles is observed at high zinc oxide concentration (x = 7 mol%). In vitro studies have shown the surface modifications and formation of Ca-P-rich layer on the glass-ceramics when immersed in simulated body fluids (SBF) for different durations. The bioactive response was found to depend on ZnO content.     

Mossbauer, infrared and magnetic susceptibility studies of iron sodium borate glasses doped by sulphur

The affect of sulphur on the structural properties of iron sodium diborate glasses having the composition {(100−x)Na₂B₄O₇+xFe₂O₃}+yS, where x=0.05, 0.15 and 0.25 mol% and Y=0, 2.5 and 5 wt% was studied by infrared, Mossbauer spectroscopy and magnetic susceptibility measurements. It was found that, for samples having 5 mol% Fe₂O₃ and free from sulphur, the iron ions are present in both Fe²⁺ and Fe³⁺ states and also 92% of the total iron enters the glass network as a glass former. The ratio of Fe³⁺/Fe²⁺ increases with increasing the iron content for sulphur-free samples and others containing sulphur. This ratio also decreases with increasing the sulphur content. The magnetic susceptibility was found to decrease with increasing the sulphur content. Also, the increase of Fe₂O₃ content led to a less symmetrical environment of Fe³⁺ ions and vice versa for the Fe²⁺ environment.     

FTIR structural investigation of gamma irradiated BaO–Na2O–B2O3–SiO2 glasses

Fourier transform infrared (FT-IR) spectra of xBaO–15Na₂O–(70−x)B₂O₃–15SiO₂ glass system with x=0, 5, 10, 15 and 20 (mol%) has been measured in the spectral range 400–4000 cm⁻¹ at room temperature in order to understand the characteristic frequencies of the chemical bonds and bonding mechanisms, which are susceptible to the structural and spectral changes. The effect of gamma irradiation in the dose range 0.1 kGy–60 kGy on the infrared absorption spectra of these glasses is also reported. The change in the glass structure due to the effect of composition is also discussed. It has been observed that irradiation of the glasses with the gamma rays increases the BO₃ groups and the non bridging oxygens which make the network loose.     

Structural and optical properties of lithium borobismuthate glasses

Glasses with compositions 25Li₂O-(75−x)Bi₂O₃-x B₂O₃, with 0?x?30 mol%, have been prepared using the melt quenching technique. The density and the molar volume have been determined. IR spectroscopy is used as a structural probe of the nearest neighbor environment in the glass network. The optical transmittance and reflectance spectrum of the glasses have been recorded in the wavelength range 400-1100 nm. The values of the optical band gap E_g^opt for indirect transition and refractive index have been determined for 0?x?30 mol%. The average electronic polarizability of the oxide ion α_o²⁻ and the optical basicity have been estimated from the calculated values of the refractive indices. Variations in the different physical parameters such as the density, molar volume, optical band gap, refractive index, average electronic polarizability of the oxide ion and optical basicity with B₂O₃ content have been analyzed and discussed in terms of the changes in the glass structure.     

Nickel ion—A structural probe in BaO-Al2O3-P2O5 glass system by means of dielectric, spectroscopic and magnetic studies

BaO-Al₂O₃-P₂O₅ glasses containing different concentrations of NiO (ranging from 0 to 1.0 mol%) were prepared. A number of studies viz., chemical durability, differential thermal analysis, spectroscopic (infrared, optical absorption spectra), magnetic susceptibility and dielectric properties (constant ε′, loss tan δ, AC conductivity σ_AC over a range of frequency and temperature) of these glasses have been carried out. The studies on chemical durability indicate that there is a significant increase in the corrosion resistance of the glasses; where as the results of differential thermal analysis suggests that there is a substantial improvement in the glass forming ability, with increase in the concentration of NiO up to 0.6 mol% in the glass matrix. The optical absorption, magnetic susceptibility and IR spectral studies point out nickel ions occupy both tetrahedral and octahedral positions in the glass network; the later positions seems to be dominant when the concentration of NiO is beyond 0.6 mol% in the glass matrix. The studies of dielectric properties reveal that the presence of nickel oxide in the glass network causes a considerable improvement in the insulating strength of the se glasses when the concentration of NiO?0.6 mol%.     

Electrical and optical properties of Ga doped zinc oxide thin films deposited at room temperature by continuous composition spread

Ga doped ZnO (GZO) thin films were deposited on glass substrates at room temperature by continuous composition spread (CCS) method. CCS is thin films growth method of various Ga_xZn_1−xO(GZO) thin film compositions on a substrate, and evaluating critical properties as a function position, which is directly related to material composition. Various compositions of Ga doped ZnO deposited at room temperature were explored to find excellent electrical and optical properties. Optimized GZO thin films with a low resistivity of 1.46 × 10⁻³ Ω cm and an average transmittance above 90% in the 550 nm wavelength region were able to be formed at an Ar pressure of 2.66 Pa and a room temperature. Also, optimized composition of the GZO thin film which had the lowest resistivity and high transmittance was found at 0.8 wt.% Ga₂O₃ doped in ZnO.     

Structure, electrical and optical properties of TiNx films by atmospheric pressure chemical vapor deposition

Titanium nitride (TiN_x) films with various nitride compositions (x) were prepared on glass substrates by atmospheric pressure chemical vapor deposition using TiCl₄ and NH₃ as precursors. The structural, compositional, electrical and optical properties of the films were studied and the results were discussed with respect to nitride composition. The results showed a linear relationship between the lattice constant and the nitride composition. Resistivity of the films was minimized near x = 1. All the TiN_x films exhibited a transmission band with a peak value of about 15% in the visible region (400-700 nm). As the wavelength increased to transition point (λ_T-R), the reflectance of the obtained films presented a sharp increase and then reached a high value of about 50% near 2000 nm. Moreover, the red-shift of transmission band and the transition wavelength (λ_T-R) with increasing the nitride composition were also discussed.     

Effect of Li2O content on physical and structural properties of vanadyl doped alkali zinc borate glasses

The effect of Li₂O content in vanadyl doped 20ZnO+xLi₂O+(30−x)Na₂O+50B₂O₃ (5≤x≥25) glasses has been studied with respect to their physical and structural properties. The absence of sharp peaks in XRD spectra of these glass samples confirms the amorphous nature. The physical parameters like density, refractive index, ionic concentration and electronic polarizability vary non-linearly with x mol% depending on the diffusivities of alkali ions. EPR and optical absorption spectra reveal that the resonance signals are characteristics of VO²⁺ ions in tetragonally compressed octahedral site. Spin-Hamiltonian, crystal field, tetragonal field and bonding parameters are found to be in good agreement with the other reported glass systems. The tetragonal distortion (g_⊥-g_∥) and Dt reveals that their values vary non-linearly with Li₂O content and reaches a minimum at x=10 mol%. An anomaly of character has been observed in all the properties of vanadyl doped glass systems, which gives a clear indication of mixed alkali effect.     

Optical characterization of Mn, Ni and Co ions doped zinc lead borate glasses

This paper reports on the development and optical characterization of heavy metal oxide (HMO)-based transparent glasses in the chemical composition of 15PbO-40B₂O₃-(45−x) ZnO−x TM²⁺ (=Mn²⁺ or Ni²⁺ or Co²⁺) (where x=0.2, 0.5 mol%). For these glasses both absorption and emission spectra have been measured, in order to understand their optical performances. The XRD profiles have confirmed their glassy nature and the FTIR spectral features have been analyzed. From the emission spectra, a bright green emission (538 nm) from Mn²⁺-glasses, an intense red emission (670 nm) from Ni²⁺ and from Co²⁺ (625 nm) glasses have been noticed very clearly. Based on the UV-absorption spectra of these materials, both direct and indirect bond gaps have been computed. Apart from the spectral analysis, different physical properties of these glasses have also been carried out. Due to the presence of both PbO and ZnO, these glasses are found to be good moisture-resistant optical systems. Both optical and physical properties have been found to be more encouraging towards their use as novel luminescent optical materials.     

Bioactivity of SiO2-CaO-P2O5-Na2O glasses containing zinc-iron oxide

Glasses with composition x(ZnO,Fe₂O₃)(65 − x)SiO₂20(CaO,P₂O₅)15Na₂O (6 ≤ x ≤ 21 mol%) were prepared by melt-quenching technique. Bioactivity of the glasses was investigated in vitro by examining apatite formation on the surface of glasses treated in acellular simulated body fluid (SBF) with ion concentrations nearly equal to those in human blood plasma. Formation of bioactive apatite layer on the samples treated in SBF was confirmed by using Fourier transform infrared reflection (FTIR) spectroscopy, grazing incidence X-ray diffraction (GI-XRD) and scanning electron microscope (SEM) equipped with energy dispersive X-ray spectrometer. Development of an apatite structure on the surface of the SBF treated glass samples as functions of composition and time could be established using the GI-XRD data. FTIR spectra of the glasses treated in SBF show features at characteristic vibration frequencies of apatite after 1-day of immersion in SBF. SEM observations revealed that the spherical particles formed on the glass surface were made of calcium and phosphorus with the Ca/P molar ratio being close to 1.67, corresponding to the value in crystalline apatite. Increase in bioactivity with increasing zinc-iron oxide content was observed. The results have been used to understand the evolution of the apatite surface layer as a function of glass composition and immersion time in SBF.     

Preparation of (CdO)1−x(PbO)x and (CdS)1−x(PbS)x thin films by spray pyrolysis technique and their characterization

Mixed thin films of (CdO)_1−x(PbO)_x and (CdS)_1−x(PbS)_x (x=0.25) were prepared on glass substrates by spray pyrolysis technique for various substrate temperatures 300, 320 and 340 °C. Structural and optical properties were studied. XRD studies reveal the formation of mixed films. The substrate temperature of 340 °C seems to be critical for the formation of CdO-PbO mixed films. It is observed that (CdS)_1−x(PbS)_x mixed films were formed at all the three substrate temperatures. The direct band gap value of (CdO)_1−x(PbO)_x and (CdS)_1−x(PbS)_x mixed films is about 2.6 and 2.37 eV, respectively.     

In vitro evaluation of bioactivity of CaO-SiO2-P2O5-Na2O-Fe2O3 glasses

Glasses with compositions 41CaO(52 − x)SiO₂4P₂O₅·xFe₂O₃3Na₂O (2 ≤ x ≤ 10 mol.%) were prepared by melt quenching method. Bioactivity of the different glass compositions was studied in vitro by treating them with simulated body fluid (SBF). The glasses treated for various time periods in SBF were evaluated by examining apatite formation on their surface using grazing incidence X-ray diffraction, Fourier transform infrared reflection spectroscopy, scanning electron microscopy and energy dispersive spectroscopy techniques. Increase in bioactivity with increasing iron oxide content was observed. The results have been used to understand the evolution of the apatite surface layer as a function of immersion time in SBF and glass composition.     

Thermoluminescence of B2O3-Li2O glass system doped with MgO

Lithium borate (LiB) glasses in the system (100−x)B₂O₃-xLi₂O with x=20, 30, 40, 50, 60 and 70 mol% were prepared. The glasses were doped with different concentrations of the order of 10⁻¹, 10⁻², 10⁻³, 10⁻⁴ and 10⁻⁵ of MgO and their thermoluminescent (TL) response was investigated. The irradiations were performed using γ rays from a ⁶⁰Co source in the dose range from 0.1 to 25 kGy. The material displayed good sensitivity for γ-rays and intensity of TL signals is dependent on γ-ray dose and Li₂O content. For each dose level and investigated temperature range (50-350 °C), exactly single isolated glow peak appears in the temperature range of 165-205 °C depending on both Li₂O concentrations and time of exposure. The shape of the glow peak has altered significantly with increase in the gamma ray dose or Li₂O concentrations. The glass composition with x=50 mol% doped with 10⁻³ mol% of MgO presented the best TL response. The results of the present study indicated that the recorded single and isolated high temperature peak is a good candidate for TL dosimetric investigations. This indicates that 50 B₂O₃-50Li₂O-doped with 10⁻³ mol% of MgO is possibly used as materials for radiation dosimetry in the dose range of 0.1-20 kGy.     

Luminescence spectra and optical properties of TeO2-WO3-Li2O glasses doped with Nd, Sm and Er rare earth ions

New tellurite glass series of the form (70-x)TeO₂-20WO₃-10Li₂O-xLn₂O₃, where x=0, 1, 3 and 5 mol% and Ln=Nd, Sm and Er, were prepared. Density of the prepared glasses was measured and molar volume was calculated. Luminescence spectra of the prepared glasses were measured at room temperature using a micro-Raman spectrometer. The obtained luminescence intensity ratio was correlated with the rare earth ion concentration, the short distance between the identical rare earth ions r(Ln-Ln) and the glass density. Optical properties like refractive index, molar refractivity and optical polarizability were theoretically calculated in order to interpret the dependence of these properties on the rare earth ion content.     

Improving dosimetric properties of tellurite glasses

Thermoluminscence (TL) properties of quaternary tellurite glass in the form 80(TeO₂)–5(TiO₂)–(15−x)(WO₃)–(x)A_nO_m where A_nO_m=Nb₂O₅, Nd₂O₃, Er₂O₃ and x mol% have been measured. TL main dosimetry peak for each produced glass sample were investigated for ⁶⁰Co gamma rays. Dosimetric properties of the quaternary tellurite glasses have been measured as a function of different compositions of the glass system in different rare earth oxides concentration by using thermoluminescence (TL) detection technique.     

Influence of valence states and co-ordination of cobalt ions on dielectric properties of PbO-Bi2O3-As2O3:CoO glass system

The glasses of the composition (40−x) PbO-15Bi₂O₃-45As₂O₃-xCoO, with 0≤x≤0.6 mol% in the steps of 0.1 were synthesized. The dielectric properties viz., dielectric constant, loss and ac conductivity over moderately larger ranges of frequency and temperature were investigated. The results were analyzed with the aid of the data on optical absorption and IR spectra. The analysis indicated that there is an increase in the insulating strength of the glasses with increase in the concentration of CoO up to 0.4 mol%.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.