Detection of rutin at DNA modified carbon paste electrode based on a mixture of ionic liquid and paraffin oil as a binder

A DNA-modified carbon paste electrode (DNA-CPIE) was designed by using a mixture of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate and paraffin oil as the binder. The electrochemistry of rutin at the DNA-CPIE was investigated by cyclic voltammetry and differential pulse voltammetry. Rutin exhibits a pair of reversible redox peaks in buffer solutions of pH 3.0, and respective electrochemical parameters are established. Under the optimal conditions, the oxidative peak current is linear with the concentration of rutin in the range from 8?×?10^?9 to 1?×?10^?5 mol L^?1, and the detection limit is 1.3?×?10^?9 mol L^?1 (at S/N?=?3). The electrode exhibits higher sensitivity compared to DNA modified carbon paste electrode without ionic liquid and better selectivity comparing with electrodes without DNA. It also showed good performance, stability, and therefore represents a viable method for the determination of rutin.     

The Use of Boron‐Doped Diamond Electrodes for the Amperometric Determination of Flavonoids in a Flow Injection System

Abstract

This paper describes the use of boron‐doped diamond electrode for the amperometric detection and quantification of flavonoids in tea samples using a flow injection system. Flavonoids are phenol derivates widely distributed in fruits, nuts, seeds, flowers, vegetable peels, and beverages; they are known to exhibit high antioxidative activities. After optimization, the experiments were performed at a fixed potential of 0.42 V vs Ag/AgCl with a flow rate of 2.5 ml min^?1 in a Britton‐Robinson buffer at pH 5.0. The results revealed that the peak current increases linearly with rutin concentration in the interval 0.1–2.5×10^?4 mol L^?1 and the detection limit was 7.7×10^?6 mol L^?1. The method was used for the determination of rutin in three different green tea (Camellia sinensis) infusions by the direct addition of 150 µL of untreated sample. The repeatability of current responses for injections of 150 µL rutin was evaluated to be 2.1% (n=20) and the analytical frequency was 100 Hz h^?1. The results were compared with the results obtained by high‐performance liquid chromatrography‐diode ray detector.     

Graphene Nanosheets Modified Glassy Carbon Electrode as a Highly Sensitive and Selective Voltammetric Sensor for Rutin

Graphene nanosheets modified glassy carbon electrode (GNs/GCE) was fabricated as voltammetric sensor for rutin with good sensitivity, selectivity and reproducibility. The sensor exhibits an adsorption‐controlled, reversible two‐proton and two electron transfer reaction for the oxidation of rutin with a peak‐to‐peak separation (ΔE_p) of 26 mV as revealed by cyclic voltammetry. Moreover, the redox peak current increased about 14 times than that on bare glassy carbon electrode (GCE). The linear response of the sensor is from 1×10^?7 to 1×10^?5 M with a detection limit of 2.1 × 10^?8 M (S/N = 3). The method was successfully applied to determine rutin in tablets with satisfied recovery.     

Electrocatalytic oxidation of NADH by rutin in biomembrane-like films on glassy carbon electrode

Stable lipid film was made by casting dipalmitoylphosphatidylcholine (DPPC) and rutin onto the surface of a glassy carbon (GC) electrode. The electrochemical behavior of rutin in the DPPC film was studied. The modified electrode coated with rutin gave quasi-reversible reduction-oxidation peak on cyclic voltammogram in the phosphate buffer (pH 7.4). The peak current did not decrease apparently after stored at 4°C for 8 hours in refrigerator. This model of biological membrane was used to investigate the oxidation of dihydronicotinamide adenine dinucleotide (NADH) by rutin. Rutin in the film acts as a mediator. The modified electrode shows a great enhancement and the anodic peak potential was reduced by about 220 mV in the oxidation of 5×10⁻³ mol L⁻¹ NADH compared with that obtained at a bare glassy carbon electrode.     

Electrochemical Behaviors of Baicalin at an Electrochemically Activated Glassy Carbon Electrode and Its Determination in Human Blood Serum

Electrochemical behavior of baicalin (BA) at an electrochemically activated glassy carbon electrode (GCE) had been investigated in Britton‐Robinson (B‐R) buffer solution (pH = 2.87) by cyclic voltammetry (CV) and square wave voltammetry (SWV). The experimental results suggested that the electrode exhibited an electrocatalytic activity toward the redox of BA. The electron transfer coefficient (α) and the standard rate constant (k_s) of BA at the electrochemically activated glassy carbon electrode were calculated. The reaction mechanism was proposed and discussed in this work. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of BA in the range of 5.0 × 10^?8 to 3.0 × 10^?6 mol L^?1 (r = 0.9990), with a detection limit of 2.0 × 10^?8 mol L^?1. The relative standard deviation (R.S.D.) for five times successful determination of 1.0 × 10^?6 mol L^?1 baicalin were 2.9%. The proposed method was also successfully applied for the determination of BA in human blood serum.     

Electrochemical determination of homocysteine using carbon nanotubes modified paste electrode and isoprenaline as a mediator

Homocysteine (HCy) is an important amino acid containing thiol group and is known as a risk factor in relation to ischemic heart disease and stroke. In this study the electrochemical determination of homocysteine (HCy) has been described using isoprenaline hydrochloride (ISP) as a mediator on multiwall carbon nanotubes modified paste electrode (MWCNTPE). Electrochemical behavior of homocysteine was investigated by cyclic voltarrtmetry and chronoamperometry. The cyclic voltammograms showed that the electrocatalytic oxidation of homocysteine occurs in the presence of ISP on the surface of MWCNTPE at a potential about 640 mV. Also, results showed that the oxidatation peak current of HCy at the modified carbon nanotubes electrode was more than unmodified electrode. The diffusion coefficient and the kinetic parameters including electron transfer coefficient and rate constant of electrocatalytic reaction were determined using electrochemical approaches. Linear sweep voltammetry results showed that electrocatalytic oxidation peak current of HCy had linear dynamic range in the range of 5.0 to 800 μmol L^?1 with a detection limit of 3.3 μmol L^?1 in pH 3.5 (universal buffer).     

Very sensitive differential pulse adsorptive stripping voltammetric determination of 4-nitrophenol at poly (diphenylamine)/multi-walled carbon nanotube-β-cyclodextrin-modified glassy carbon electrode

In this work, a glassy carbon electrode (GCE) modified with poly (diphenylamine)/multi-walled carbon nanotubes-β-cyclodextrin (PDPA/MWCNT-β-CD) film was constructed and used for the determination of 4-nitrophenol (4-NP). Diphenylamine was successfully electropolymerised onto MWCNT-β-CD-modified GCE by cyclic voltammetry in monomer solution and 5 mol L^?1 H₂SO₄. The surface morphology of PDPA/MWCNT-β-CD film was characterised using scanning electron microscopy and electrochemical impedance spectroscopy. After adsorption of 4-NP on PDPA/MWCNT-β-CD at 0.2 V for 150 s, it showed a well-defined reduction peak in phosphate buffer solution at pH = 7. The PDPA/MWCNT-β-CD film enhanced the reduction peak current due to the complex formation between β-CD and 4-NP, presence of conductive polymer film as electron transfer mediator and also ability of MWCNTs for strong adsorptive and catalytic effect. Peak current increased linearly with 4-NP concentration in the range of 0.1 to 13.9 µg L^?1. The detection limit was obtained as 0.02 µg L^?1, which is better than other reported detection limits for the determination of 4-NP. The results showed that modified electrode has good sensitivity and selectivity. This sensor was used for the determination of 4-NP in water samples.     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Voltammetric Study and Detection of Methane on Nickel Hydroxide–Modified Nickel Electrode

Abstract

The nickel hydroxide–modified nickel (NMN) electrode was prepared by cyclic voltammetry. The modified electrode exhibited better catalytic effect toward electrochemical oxidation of methane in 1.0 mol · L^?1 NaOH solution. The catalytic activation of nickel hydroxide on the nickel electrode surface was investigated in different supporting electrolyte solutions by the cyclic voltammetry method in detail, and the related electrochemical oxidation of methane at the NMN electrode was first proposed by amperometric i‐t curve method under the experiment conditions. The results indicated that in the 1.0 mol · L^?1 NaOH solution, the anodic peak current increased with the increased concentration of methane.     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

A Sensitive Sensor Based on Single‐walled Carbon Nanotubes: Its Preparation,Characterization and Application in the Electrochemical Determination of Drug Clorsulon in Milk Samples

Within this paper, a glassy carbon electrode modified with single‐walled carbon nanotubes (SWCNTs?GCE) was prepared, and employed for the determination of clorsulon (Clo), which is a frequently used veterinary drug against common liver fluke. The comprehensive topographical and electrochemical characterizations of bare GCE and SWCNTs?GCE were performed by atomic force microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Significantly enhanced electrochemical characteristics of SWCNTs?GCE toward a ferrocyanide/ferricyanide redox couple was observed when compared to bare GCE. Further, the prepared sensor was applied for the voltammetric determination of Clo, which was electrochemically investigated for the first time in this work. Voltammetric experiments were performed using square‐wave voltammetry with optimized parameters in phosphate buffer solution, pH 6.8, which was selected as the most suitable medium for the determination of Clo. The corresponding current at approx. +1.1 V increased linearly with Clo concentration within two linear dynamic ranges of 0.75–4.00 μmol L^?1 (R²=0.9934) and 4.00–15.00 μmol L^?1 (R²=0.9942) with a sensitivity for the first calibration range of 0.76 μA L μmol^?1, a limit of detection of 0.19 μmol L^?1, and a limit of quantification of 0.64 μmol L^?1. The developed method was subsequently applied for quantitative analysis of Clo in milk samples with results proving high repeatability and recovery.     

Ruthenium Hexacyanoferrate (III) Modified Glassy Carbon Electrode for Determination of Captopril

A glassy carbon electrode modified with a ruthenium (III) hexacyanoferrate film was investigated for the determination of captopril in pharmaceutical formulations. The RuOHCF film was deposited on the surface of the electrode after applying 50 successive cycles and subsequent stabilization in a mixture of NaNO₃ 0.50 mol L^?1+HCl 0.050 mol L^?1 used as supporting electrolyte. The main processes responsible for the redox electrode response are attributed to the system Ru^II/Ru^III/Ru^IV, and appeared at ?0.080, 0.86 and 1.01 V (vs. SCE). The redox process at ?0.080 V was selected for the determination of captopril in the present study, once it provided higher sensibility and occurs in a lower potential than the other ones which can prevent interferences. The experimental parameters used in the determination of the analyte, using differential pulse voltammetry were optimized: pulse amplitude: 50 mV, scan rate: 5 mV s^?1 and potential window: ?0.5 to 0.2 V (vs. SCE). The analytical application of the sensor in real samples demonstrated a linear range between 0.060 and 0.80 µmol L^?1 (r=0.998) with a detection limit of 0.047 µmol L^?1. A mechanism based on co‐precipitation of captopril and the Ru (III) complex in the film is presented once the signal of the Ru^II/III redox couple decreases with increasing the analyte concentration. Recoveries of 99 to 100 % were achieved in pharmaceutical samples and the proposed procedure agreed with the HPLC official method within 95 % confidence level, according to the t‐Student test.     

Determination of total antimony(III,V) by square-wave anodic stripping voltammetry with in situ plated bismuth-film electrode

A sensitive and reliable method is described for the determination of total Sb(III,?V) at traces levels by Osteryoung square-wave anodic stripping voltammery (OSWASV). This method is based on the co-deposition of Sb(III,?V) with Bi(III) onto an edge-plane pyrolytic graphite substrate at an accumulation step. OSWASV studies indicated that the co-deposited antimony was oxidised with anodic scans to give an enhanced anodic peak at about 450?mV vs. Ag/AgCl (sat. KCl). The anodic stripping peak current was directly proportional to the total concentration of antimony in the ranges of 0.01–0.10?µg?L^?1, 0.10–1.0?µg?L^?1 and 1.0–18.0?µg?L^?1 with correlation coefficient higher than 0.995 when 2.0?mol?L^?1 hydrochloric acid was used. The detection limits calculated as S/N?=?3 was 5.0?ng?L^?1 in 2.0?mol?L^?1 hydrochloric acid at 180?s deposition time. The relative standard deviation was 5% (n?=?6) at 0.10?µg?L^?1 level of antimony. The analytical results demonstrate that the proposed method is applicable to analyses of real water samples.     

Evaluation of a Multi-Walled Carbon Nanotube-Hemin Composite for the Voltammetric Determination of Hydrogen Peroxide in Dental Products

A simple, low cost sensor was developed for the voltammetric determination of hydrogen peroxide in mouthwash and dental whitening gel based on multi-walled carbon nanotubes incorporated with hemin. The sensor showed electrocatalytic activity toward the reduction of hydrogen peroxide in 0.05 mol L^?1 Tris-HCl buffer solution (pH 7.0) using cyclic voltammetry. The optimum composition of paste was 20:10:70% (m/m/m) (multi-walled carbon nanotubes:hemin:mineral oil). A linear plot of the square root of scan rate vs. cathodic peak current showed that reduction of hydrogen peroxide is diffusion controlled. Using linear sweep voltammetry, the analytical curve ranged from 0.2 up to 1.4 mmol L^?1 (r = 0.9996) with a sensitivity of 3.62 × 10^?2 mA mol^?1 L. The limits of detection and quantification were found to be 12.5 µmol L^?1 and 41.7 µmol L^?1, respectively. The developed method was applied for hydrogen peroxide determination in dental formulations. The results were compared with a volumetric method as a reference technique. No significant differences at the 95% level (paired student t test) were observed, thus demonstrating the accuracy of the sensor for the analysis of real samples.     

A sensitive electrochemical sensor for detection of rutin based on a gold nanocage‐modified electrode

In this article, an electrochemical sensor based on a gold nanocage (AuNC)‐modified carbon ionic liquid electrode (CILE) was fabricated and applied to the sensitive rutin determination. The presence of AuNCs on the electrode surface greatly improved the electrochemical performance of the working electrode due to its specific microstructure and high metal conductivity. Electrochemical behavior of rutin on AuNCs/CILE was studied using cyclic voltammetry and differential pulse voltammetry with the related electrochemical parameters calculated. Under the optimal experimental conditions, the oxidation peak current of rutin and its concentration had good linear relationship in the range from 4.0 × 10^?9 to 7.0 × 10^?4 mol/L with a low detection limit of 1.33 × 10^?9 mol/L (3σ). This fabricated AuNCs/CILE was applied to direct detection of the rutin concentration in drug samples with satisfactory results, showing the real application of AuNCs in the field of chemically modified electrodes.     

Acetylferrocene Modified Carbon Paste Electrode; A Sensor for Electrocatalytic Determination of Hydrazine

The electrocatalytic oxidation of hydrazine at a carbon paste electrode spiked with acetylferrocene as a mediator was studied by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. In contrast to other ferrocenic compounds, acetylferrocene exhibits a chemical irreversible behavior, but it can act as an effective mediator for electrocatalytic oxidation of hydrazine, too. The heterogeneous electron transfer rate constant between acetylferrocene and the electrode substrate (carbon paste) and the diffusion coefficient of spiked acetylferrocene in silicon oil were estimated to be about 3.45×10^?4 cm s^?1 and 4.45×10^?9 cm² s^?1, respectively. It has been found that under the optimum conditions (pH 7.5) the oxidation of hydrazine occurs at a potential of about 228 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak current of hydrazine was linearly dependent on its concentration and the obtained linear range was 3.09×10^?5 M–1.03×10^?3 M. The detection limit (2σ) has been determined as 2.7×10^?5 M by cyclic voltammetry. Also, the peak current was increased linearly with the concentration of hydrazine in the range of 1×10^?5 M–1×10^?3 M by differential pulse voltammetry with a detection limit of 1×10^?5 M. This catalytic oxidation of hydrazine has been applied as a selective, simple, and precise new method for the determination of hydrazine in water samples.     

Voltammetric Determination of Rutin Using a Carbon Composite Electrode Modified with Copper(II)-Resin

Abstract

The preparation and electrochemical characterization of a carbon composite electrode modified with copper(II)-resin as well as its behavior toward rutin were investigated using cyclic and linear sweep voltammetry. The best voltammetric response was observed for a composite composition of 20% (m/m) copper(II)-resin, 0.10 mol L^?1 KNO₃/10^?6 mol L^?1 HNO₃ solution (pH 6.0) as the supporting electrolyte, and a scan rate of 50 mVs^?1. A linear voltammetric response for rutin was obtained in the concentration range from 9.90 × 10^?7 to 8.07 × 10^?6 mol L^?1, with a detection limit of 2.65 × 10^?8 mol L^?1. The proposed electrode was useful for the quality control and routine analysis of rutin in pharmaceutical formulations.     

Electrochemical Determination of Dopamine with Ruthenium(III)-Modified Glassy Carbon and Screen-Printed Electrodes

Here is reported for the first time the application of sodium bis[N-2-oxyphenyl-5-bromosalicylideneiminato-ONO]ruthenate(III) as a mediator with multiwalled carbon nanotubes and Nafion at glassy carbon and screen-printed electrodes for the determination of dopamine in the presence of ascorbic acid. Electrochemical studies were performed using cyclic voltammetry, differential pulse voltammetry, and flow injection amperometry. In flow injection mode, the flow rate was 0.4?mL?min^?1, the injection volume 250?µL, and the operation potential 0.05?V vs. Ag/AgCl. In 0.1M pH 7.5 phosphate buffer, the sensor provided a linear dynamic range up to 50?mg?L^?1 dopamine with a detection limit of 0.11?±?0.04?mg?L^?1. The sensor was used for the determination of dopamine in ampoules of dopamine hydrochloride by cyclic voltammetry, differential pulse voltammetry, and flow injection amperometry.     

Electrochemical sensor for heparin based on a poly(thionine) modified glassy carbon electrode

A poly(thionine) thin film modified electrode was successfully assembled on the surface of the glassy carbon electrode by means of electrochemical polymerization, which was carried out with cyclic voltammetric sweeping in the potential range 0 to +1.4 V (vs. Ag/AgCl) in perchloric acid solution containing 0.1 mmol L^?1 thionine. The film modified electrode exhibited a couple of well-defined redox peaks, and the redox peaks decreased correspondingly without a shift of the peak potential after the addition of heparin. The conditions of the binding reaction and the electrochemical detection were optimized. Under the optimum conditions the decrease of the peak current was proportional to the concentration of heparin in the range 4.0 to 22.0 μg mL^?1 and the detection limit was 0.28 μg mL^?1. The relative standard deviation (RSD) for five parallel determinations of 10.0 μg mL^?1 heparin was 0.93%. The effects of potentially interfering species were investigated and the method was successfully applied to the determination of heparin in a pharmaceutical formulation.     

Spectrophotometric determination of Chromium(VI) using cyclam as a reagent

A simple, rapid, sensitive, and inexpensive method for spectrophotometric determination of chromium(VI), based on the absorbance of its complex with 1,4,8,11-tetraazacyclotetradecane (cyclam) is presented. The complex showed a molar absorbtivity of 1.5?×?10⁴?L?mol^?1?cm^?1 at 379?nm. Under optimum experimental conditions, a pH of 4.5 and 1.960?×?10³?mg?L^?1 cyclam were selected, and all measurements were performed 10?min after mixing. Major cations and anions did not show any interference; Beer's law was applicable in the concentration range 0.2–20?mg?L^?1 with a detection limit of 0.001?mg?L^?1. The standard deviation in the determination is ±0.5?mg?L^?1 for a 15.0?mg?L^?1 solution (n?=?7). The described method provides a simple and reliable means for determination of Cr(VI) in real samples.