Flame Spray Pyrolysis for Finding Multicomponent Nanomaterials with Superior Electrochemical Properties in the CoOx‐FeOx System for Use in Lithium‐Ion Batteries

High‐temperature flame spray pyrolysis is employed for finding highly efficient nanomaterials for use in lithium‐ion batteries. CoO_x‐FeO_x nanopowders with various compositions are prepared by one‐pot high‐temperature flame spray pyrolysis. The Co and Fe components are uniformly distributed over the CoO_x‐FeO_x composite powders, irrespective of the Co/Fe mole ratio. The Co‐rich CoO_x‐FeO_x composite powders with Co/Fe mole ratios of 3:1 and 2:1 have mixed crystal structures with CoFe₂O₄ and Co₃O₄ phases. However, Co‐substituted magnetite composite powders prepared from spray solutions with Co and Fe components in mole ratios of 1:3, 1:2, and 1:1 have a single phase. Multicomponent CoO_x‐FeO_x powders with a Co/Fe mole ratio of 2:1 and a mixed crystal structure with Co₃O₄ and CoFe₂O₄ phases show high initial capacities and good cycling performance. The stable reversible discharge capacities of the composite powders with a Co/Fe mole ratio of 2:1 decrease from 1165 to 820 mA h g^?1 as the current density is increased from 500 to 5000 mA g^?1; however, the discharge capacity again increases to 1310 mA h g^?1 as the current density is restored to 500 mA g^?1.     

A Robust Solid Electrolyte Interphase Layer Augments the Ion Storage Capacity of Bimetallic‐Sulfide‐Containing Potassium‐Ion Batteries

Metal–organic framework‐derived NiCo_2.5S₄ microrods wrapped in reduced graphene oxide (NCS@RGO) were synthesized for potassium‐ion storage. Upon coordination with organic potassium salts, NCS@RGO exhibits an ultrahigh initial reversible specific capacity (602 mAh g^?1 at 50 mA g^?1) and ultralong cycle life (a reversible specific capacity of 495 mAh g^?1 at 200 mA g^?1 after 1 900 cycles over 314 days). Furthermore, the battery demonstrates a high initial Coulombic efficiency of 78 %, outperforming most sulfides reported previously. Advanced ex situ characterization techniques, including atomic force microscopy, were used for evaluation and the results indicate that the organic potassium salt‐containing electrolyte helps to form thin and robust solid electrolyte interphase layers, which reduce the formation of byproducts during the potassiation–depotassiation process and enhance the mechanical stability of electrodes. The excellent conductivity of the RGO in the composites, and the robust interface between the electrodes and electrolytes, imbue the electrode with useful properties; including, ultrafast potassium‐ion storage with a reversible specific capacity of 402 mAh g^?1 even at 2 A g^?1.     

Hierarchical Metal Sulfide/Carbon Spheres: A Generalized Synthesis and High Sodium‐Storage Performance

The development of suitable anode materials is far from satisfactory and is a major scientific challenge for a competitive sodium‐ion battery technology. Metal sulfides have demonstrated encouraging results, but still suffer from sluggish kinetics and severe capacity decay associated with the phase change. Herein we show that rational electrode design, that is, building efficient electron/ion mixed‐conducting networks, can overcome the problems resulting from conversion reactions. A general strategy for the preparation of hierarchical carbon‐coated metal sulfide (MS?C) spheres through thermal sulfurization of metal glycerate has been developed. We demonstrate the concept by synthesizing highly uniform hierarchical carbon coated vanadium sulfide (V₂S₃?C) spheres, which exhibit a highly reversibly sodium storage capacity of 777 mAh g^?1 at 100 mA g^?1, excellent rate capability (410 mAh g^?1 at 4000 mA g^?1), and impressive cycling ability.     

Long‐Life Room‐Temperature Sodium–Sulfur Batteries by Virtue of Transition‐Metal‐Nanocluster–Sulfur Interactions

Room‐temperature sodium–sulfur (RT‐Na/S) batteries hold significant promise for large‐scale application because of low cost of both sodium and sulfur. However, the dissolution of polysulfides into the electrolyte limits practical application. Now, the design and testing of a new class of sulfur hosts as transition‐metal (Fe, Cu, and Ni) nanoclusters (ca. 1.2 nm) wreathed on hollow carbon nanospheres (S@M‐HC) for RT‐Na/S batteries is reported. A chemical couple between the metal nanoclusters and sulfur is hypothesized to assist in immobilization of sulfur and to enhance conductivity and activity. S@Fe‐HC exhibited an unprecedented reversible capacity of 394 mAh g^?1 despite 1000 cycles at 100 mA g^?1, together with a rate capability of 220 mAh g^?1 at a high current density of 5 A g^?1. DFT calculations underscore that these metal nanoclusters serve as electrocatalysts to rapidly reduce Na₂S₄ into short‐chain sulfides and thereby obviate the shuttle effect.     

Morphology‐Dependent Electrochemical Properties of CuS Hierarchical Superstructures

Hierarchical superstructures formed by self‐assembled nanoparticles exhibit interesting electrochemical properties that can potentially be exploited in Li‐ion batteries (LIBs) as possible electrode materials. In this work, we tested two different morphologies of CuS superstructures for electrodes, namely, tubular dandelion‐like and ball‐like assemblies, both of which are composed of similar small covellite nanoparticles. These two CuS morphologies are characterized by their markedly different electrochemical performances, suggesting that their complex structures/morphologies influence the electrochemical properties. At 1.12 A g^?1, the cells made with CuS tubular structures delivered about 420 mAh g^?1, and at 0.56 A g^?1, the capacity was as high as about 500 mAh g^?1 with good capacity retention. Their ease of preparation and processing, together with good electrochemical performance, make CuS tubular dandelion‐like clusters attractive for developing low‐cost LIBs based on conversion reactions.     

Double‐Helix Structure in Carrageenan–Metal Hydrogels: A General Approach to Porous Metal Sulfides/Carbon Aerogels with Excellent Sodium‐Ion Storage

The metal sulfide‐carbon nanocomposite is a new class of anode material for sodium ion batteries, but its development is restricted by its relative poor rate ability and cyclic stability. Herein, we report the use of double‐helix structure of carrageenan–metal hydrogels for the synthesis of 3D metal sulfide (M_xS_y) nanostructure/carbon aerogels (CAs) for high‐performance sodium‐ion storage. The method is unique, and can be used to make multiple M_xS_y/CAs (such as FeS/CA, Co₉S₈/CA, Ni₃S₄/CA, CuS/CA, ZnS/CA, and CdS/CA) with ultra‐small nanoparticles and hierarchical porous structure by pyrolyzing the carrageenan–metal hydrogels. The as‐prepared FeS/CA exhibits a high reversible capacity and excellent cycling stability (280 mA h^?1 at 0.5 A g^?1 over 200 cycles) and rate performance (222 mA h^?1 at 5 A g^?1) when used as the anode material for sodium‐ion batteries. The work shows the value of biomass‐derived metal sulfide–carbon heterostuctures in sodium‐ion storage.     

One‐Step Pyro‐Synthesis of a Nanostructured Mn3O4/C Electrode with Long Cycle Stability for Rechargeable Lithium‐Ion Batteries

A nanostructured Mn₃O₄/C electrode was prepared by a one‐step polyol‐assisted pyro‐synthesis without any post‐heat treatments. The as‐prepared Mn₃O₄/C revealed nanostructured morphology comprised of secondary aggregates formed from carbon‐coated primary particles of average diameters ranging between 20 and 40 nm, as evidenced from the electron microscopy studies. The N₂ adsorption studies reveal a hierarchical porous feature in the nanostructured electrode. The nanostructured morphology appears to be related to the present rapid combustion strategy. The nanostructured porous Mn₃O₄/C electrode demonstrated impressive electrode properties with reversible capacities of 666 mAh g^?1 at a current density of 33 mA g^?1, good capacity retentions (1141 mAh g^?1 with 100 % Coulombic efficiencies at the 100^th cycle), and rate capabilities (307 and 202 mAh g^?1 at 528 and 1056 mA g^?1, respectively) when tested as an anode for lithium‐ion battery applications.     

Scalable Dry Production Process of a Superior 3D Net‐Like Carbon‐Based Iron Oxide Anode Material for Lithium‐Ion Batteries

Carbon‐based transition‐metal oxides are considered as an appropriate anode material candidate for lithium‐ion batteries. Herein, a simple and scalable dry production process is developed to produce carbon‐encapsulated 3D net‐like FeO_x /C materials. The process is simply associated with the pyrolysis of a solid carbon source, such as filter paper, adsorbed with ferrite nitrate. The carbon derived from filter paper induces a carbothermal reduction to form metallic Fe, the addition of carbon and iron increase the conductivity of this material. As expected, this 3D net‐like FeO_x /C composite delivers an excellent charge capacity of 851.3 mAh g⁻¹ after 50 cycles at 0.2 A g⁻¹ as well as high stability and rate performance of 714.7 mAh g⁻¹ after 300 cycles at 1 A g⁻¹. Superior performance, harmlessness, low costs, and high yield may greatly stimulate the practical application of the products as anode materials in lithium‐ion batteries.     

Coated/Sandwiched rGO/CoSx Composites Derived from Metal–Organic Frameworks/GO as Advanced Anode Materials for Lithium‐Ion Batteries

Rational composite materials made from transition metal sulfides and reduced graphene oxide (rGO) are highly desirable for designing high‐performance lithium‐ion batteries (LIBs). Here, rGO‐coated or sandwiched CoS_x composites are fabricated through facile thermal sulfurization of metal–organic framework/GO precursors. By scrupulously changing the proportion of Co²⁺ and organic ligands and the solvent of the reaction system, we can tune the forms of GO as either a coating or a supporting layer. Upon testing as anode materials for LIBs, the as‐prepared CoS_x‐rGO‐CoS_x and rGO@CoS_x composites demonstrate brilliant electrochemical performances such as high initial specific capacities of 1248 and 1320 mA h g^?1, respectively, at a current density of 100 mA g^?1, and stable cycling abilities of 670 and 613 mA h g^?1, respectively, after 100 charge/discharge cycles, as well as superior rate capabilities. The excellent electrical conductivity and porous structure of the CoS_x/rGO composites can promote Li⁺ transfer and mitigate internal stress during the charge/discharge process, thus significantly improving the electrochemical performance of electrode materials.     

Green Template‐Free Synthesis of Hierarchical Shuttle‐Shaped Mesoporous ZnFe2O4 Microrods with Enhanced Lithium Storage for Advanced Li‐Ion Batteries

In the work, a facile and green two‐step synthetic strategy was purposefully developed to efficiently fabricate hierarchical shuttle‐shaped mesoporous ZnFe₂O₄ microrods (MRs) with a high tap density of ～0.85 g cm³, which were assembled by 1D nanofiber (NF) subunits, and further utilized as a long‐life anode for advanced Li‐ion batteries. The significant role of the mixed solvent of glycerin and water in the formation of such hierarchical mesoporous MRs was systematically investigated. After 488 cycles at a large current rate of 1000 mA g^?1, the resulting ZnFe₂O₄ MRs with high loading of ～1.4 mg per electrode still preserved a reversible capacity as large as ～542 mAh g^?1. Furthermore, an initial charge capacity of ～1150 mAh g^?1 is delivered by the ZnFe₂O₄ anode at 100 mA g^?1, resulting in a high Coulombic efficiency of ～76 % for the first cycle. The superior Li‐storage properties of the as‐obtained ZnFe₂O₄ were rationally associated with its mesoprous micro‐/nanostructures and 1D nanoscaled building blocks, which accelerated the electron transportation, facilitated Li⁺ transfer rate, buffered the large volume variations during repeated discharge/charge processes, and provided rich electrode–electrolyte sur‐/interfaces for efficient lithium storage, particularly at high rates.     

Hollow and Yolk‐Shell Iron Oxide Nanostructures on Few‐Layer Graphene in Li‐Ion Batteries

We report a simple and template‐free strategy for the synthesis of hollow and yolk‐shell iron oxide (FeO_x) nanostructures sandwiched between few‐layer graphene (FLG) sheets. The morphology and microstructure of this material are characterized in detail by X‐ray diffraction, X‐ray absorption near‐edge structure, X‐ray photoelectron spectroscopy, Raman spectroscopy, scanning and transmission electron microscopy. Its properties are evaluated as negative electrode material for Li‐ion batteries and compared with those of solid FeO_x/FLG and two commercial iron oxides. In all cases, the content of carbon in the electrode has a great influence on the performance. The use of pristine FLG improves the capacity retention and further enhancement is achieved with the hollow structure. For a low carbon loading of 18 wt. %, the presence of metallic iron in the hollow and yolk‐shell FeO_x/FLG composite significantly enhances the capacity retention, albeit with a relatively lower initial reversible capacity, retaining above 97 % after 120 cycles at 1000 mA g^?1 in the voltage range of 0.1–3.0 V.     

2 D Manganese Vanadate Nanoflakes as High‐Performance Anode for Lithium‐Ion Batteries

Nanometer‐sized flakes of MnV₂O₆ were synthesized by a hydrothermal method. No surfactant, expensive metal salt, or alkali reagent was used. These MnV₂O₆ nanoflakes present a high discharge capacity of 768 mA h g^?1 at 200 mA g^?1, good rate capacity, and excellent cycling stability. Further investigation demonstrates that the nanoflake structure and the specific crystal structure make the prepared MnV₂O₆ a suitable material for lithium‐ion batteries.     

Hermetically Coated and Well‐Separated Co3O4 Nanophase within Porous Graphitic Carbon Nanosheets: Synthesis,Confinement Effect,and Improved Lithium‐Storage Capacity and Durability

Considerable lithium‐driven volume changes and loss of crystallinity on cycling have impeded the sustainable use of transition metal oxides (MOs) as attractive anode materials for advanced lithium‐ion batteries that have almost six times the capacity of carbon per unit volume. Herein, Co₃O₄ was used as a model MO in a facile process involving two pyrolysis steps for in situ encapsulation of nanosized MO in porous two‐dimensional graphitic carbon nanosheets (2D‐GCNs) with high surface areas and abundant active sites to overcome the above‐mentioned problems. The proposed method is inexpensive, industrially scalable, and easy to operate with a high yield. TEM revealed that the encaged Co₃O₄ is well separated and uniformly dispersed with surrounding onionlike graphitic layers. By taking advantage of the high electronic conductivity and confinement effect of the surrounding 2D‐GCNs, a hierarchical GCNs‐coated Co₃O₄ (Co₃O₄@GCNs) anode with 43.5 wt % entrapped active nanoparticles delivered a remarkable initial specific capacity of 1816 mAh g^?1 at a current density of 100 mA g^?1. After 50 cycles, the retained capacity is as high as 987 mAh g^?1. When the current density was increased to 1000 mA g^?1, the anode showed a capacity retention of 416 mAh g^?1. Enhanced reversible rate capability and prolonged cycling stability were found for Co₃O₄@GCN compared to pure GCNs and Co₃O₄. The Co₃O₄@GCNs hybrid holds promise as an efficient candidate material for anodes due to its low cost, environmentally friendly nature, high capacity, and stability.     

Microwave‐Induced In Situ Synthesis of Zn2GeO4/N‐Doped Graphene Nanocomposites and Their Lithium‐Storage Properties

Zn₂GeO₄/N‐doped graphene nanocomposites have been synthesized through a fast microwave‐assisted route on a large scale. The resulting nanohybrids are comprised of Zn₂GeO₄ nanorods that are well‐embedded in N‐doped graphene sheets by in situ reducing and doping. Importantly, the N‐doped graphene sheets serve as elastic networks to disperse and electrically wire together the Zn₂GeO₄ nanorods, thereby effectively relieving the volume‐expansion/contraction and aggregation of the nanoparticles during charge and discharge processes. We demonstrate that an electrode that is made of the as‐formed Zn₂GeO₄/N‐doped graphene nanocomposite exhibits high capacity (1463 mAh g^?1 at a current density of 100 mA g^?1), good cyclability, and excellent rate capability (531 mAh g^?1 at a current density of 3200 mA g^?1). Its superior lithium‐storage performance could be related to a synergistic effect of the unique nanostructured hybrid, in which the Zn₂GeO₄ nanorods are well‐stabilized by the high electronic conduction and flexibility of N‐doped graphene sheets. This work offers an effective strategy for the fabrication of functionalized ternary‐oxide‐based composites as high‐performance electrode materials that involve structural conversion and transformation.     

Stereoselectively Assembled Metal–Organic Framework (MOF) Host for Catalytic Synthesis of Carbon Hybrids for Alkaline‐Metal‐Ion Batteries

Cost‐effective metal‐based nanostructured hybrids have been widely dedicated to potential energy storage and conversion applications. Herein, we develop a facile methodology for the synthesis of precise carbon‐confined hybrid nanostructures by stereoselective assembly accompanied by catalytic pyrolysis. Polyacrylonitrile fiber films favors not only metal‐polymer coordination, but also oriented assembly to ensure the well‐defined nanostructure of the carbon hybrids. During chemical vapor deposition (CVD), cobalt‐nanoparticle‐catalyzed growth of carbon‐nanotube branches driven by organic molecules (e.g. melamine) delivers hierarchical carbon hybrids. The resulting carbon hybrids exhibit outstanding electrochemical performance for metal‐ion batteries, for example, a high specific capacity of 680 mAh g^?1 after 320 cycles (Li‐storage) and 220 mAh g^?1 after 500 cycles (Na‐storage) without decay.     

A Self‐Standing and Flexible Electrode of Yolk–Shell CoS2 Spheres Encapsulated with Nitrogen‐Doped Graphene for High‐Performance Lithium‐Ion Batteries

Flexible lithium‐ion batteries (LIBs) have recently attracted increasing attention with the fast development of bendable electronic systems. Herein, a facile and template‐free solvothermal method is presented for the fabrication of hybrid yolk–shell CoS₂ and nitrogen‐doped graphene (NG) sheets. The yolk–shell architecture of CoS₂ encapsulated with NG coating is designed for the dual protection of CoS₂ to address the structural and interfacial stability concerns facing the CoS₂ anode. The as‐prepared composite can be assembled into a film, which can be used as a binder‐free and flexible electrode for LIBs that does not require any carbon black conducting additives or current collectors. When evaluating lithium‐storage properties, such a flexible electrode exhibits a high specific capacity of 992 mAh g^?1 in the first reversible discharge capacity at a current rate of 100 mA g^?1 and high reversible capacity of 882 mAh g^?1 after 150 cycles with excellent capacity retention of 89.91 %. Furthermore, a reversible capacity as high as 655 mAh g^?1 is still achieved after 50 cycles even at a high rate of 5 C due to the yolk–shell structure and NG coating, which not only provide short Li‐ion and electron pathways, but also accommodate large volume variation.     

Two‐Dimensional Cobalt‐/Nickel‐Based Oxide Nanosheets for High‐Performance Sodium and Lithium Storage

Two‐dimensional (2D) nanomaterials are one of the most promising types of candidates for energy‐storage applications due to confined thicknesses and high surface areas, which would play an essential role in enhanced reaction kinetics. Herein, a universal process that can be extended for scale up is developed to synthesise ultrathin cobalt‐/nickel‐based hydroxides and oxides. The sodium and lithium storage capabilities of Co₃O₄ nanosheets are evaluated in detail. For sodium storage, the Co₃O₄ nanosheets exhibit excellent rate capability (e.g., 179 mA h g^?1 at 7.0 A g^?1 and 150 mA h g^?1 at 10.0 A g^?1) and promising cycling performance (404 mA h g^?1 after 100 cycles at 0.1 A g^?1). Meanwhile, very impressive lithium storage performance is also achieved, which is maintained at 1029 mA h g^?1 after 100 cycles at 0.2 A g^?1. NiO and NiCo₂O₄ nanosheets are also successfully prepared through the same synthetic approach, and both deliver very encouraging lithium storage performances. In addition to rechargeable batteries, 2D cobalt‐/nickel‐based hydroxides and oxides are also anticipated to have great potential applications in supercapacitors, electrocatalysis and other energy‐storage‐/‐conversion‐related fields.     

Multi‐Electron Reactions Enabled by Anion‐Based Redox Chemistry for High‐Energy Multivalent Rechargeable Batteries

The development of multivalent metal (such as Mg and Ca) based battery systems is hindered by lack of suitable cathode chemistry that shows reversible multi‐electron redox reactions. Cationic redox centres in the classical cathodes can only afford stepwise single‐electron transfer, which are not ideal for multivalent‐ion storage. The charge imbalance during multivalent ion insertion might lead to an additional kinetic barrier for ion mobility. Therefore, multivalent battery cathodes only exhibit slope‐like voltage profiles with insertion/extraction redox of less than one electron. Taking VS₄ as a model material, reversible two‐electron redox with cationic–anionic contributions is verified in both rechargeable Mg batteries (RMBs) and rechargeable Ca batteries (RCBs). The corresponding cells exhibit high capacities of >300 mAh g^?1 at a current density of 100 mA g^?1 in both RMBs and RCBs, resulting in a high energy density of >300 Wh kg^?1 for RMBs and >500 Wh kg^?1 for RCBs. Mechanistic studies reveal a unique redox activity mainly at anionic sulfides moieties and fast Mg²⁺ ion diffusion kinetics enabled by the soft structure and flexible electron configuration of VS₄.     

Hierarchical MoS2@Carbon Microspheres as Advanced Anodes for Li‐Ion Batteries

Hierarchical hybridized nanocomposites with rationally constructed compositions and structures have been considered key for achieving superior Li‐ion battery performance owing to their enhanced properties, such as fast lithium ion diffusion, good collection and transport of electrons, and a buffer zone for relieving the large volume variations during cycling processes. Hierarchical MoS₂@carbon microspheres (HMCM) have been synthesized in a facile hydrothermal treatment. The structure analyses reveal that ultrathin MoS₂ nanoflakes (ca. 2–5 nm) are vertically supported on the surface of carbon nanospheres. The reversible capacity of the HMCM nanocomposite is maintained at 650 mA h g^?1 after 300 cycles at 1 A g^?1. Furthermore, the capacity can reach 477 mA h g^?1 even at a high current density of 4 A g^?1. The outstanding electrochemical performance of HMCM is attributed to the synergetic effect between the carbon spheres and the ultrathin MoS₂ nanoflakes. Additionally, the carbon matrix can supply conductive networks and prevent the aggregation of layered MoS₂ during the charge/discharge process; and ultrathin MoS₂ nanoflakes with enlarged surface areas, which can guarantee the flow of the electrolyte, provide more active sites and reduce the diffusion energy barrier of Li⁺ ions.     

Boron‐Doped,Carbon‐Coated SnO2/Graphene Nanosheets for Enhanced Lithium Storage

Heteroatom doping is an effective method to adjust the electrochemical behavior of carbonaceous materials. In this work, boron‐doped, carbon‐coated SnO₂/graphene hybrids (BCTGs) were fabricated by hydrothermal carbonization of sucrose in the presence of SnO₂/graphene nanosheets and phenylboronic acid or boric acid as dopant source and subsequent thermal treatment. Owing to their unique 2D core–shell architecture and B‐doped carbon shells, BCTGs have enhanced conductivity and extra active sites for lithium storage. With phenylboronic acid as B source, the resulting hybrid shows outstanding electrochemical performance as the anode in lithium‐ion batteries with a highly stable capacity of 1165 mA h g^?1 at 0.1 A g^?1 after 360 cycles and an excellent rate capability of 600 mA h g^?1 at 3.2 A g^?1, and thus outperforms most of the previously reported SnO₂‐based anode materials.