Chemical Dual‐Responsive Wettability of Superhydrophobic PANI‐PAN Coaxial Nanofibers

PANI‐PAN coaxial nanofibers have been prepared by electro‐spinning during polymerization. The surface of the resulting nanofibers is superhydrophobic with a water contact angle up to 164.5°. Conductivity of the PANI‐PAN nanofibers is about 4.3 × 10⁻² S · cm⁻¹. The superhydrophobic nanofibers show a chemical dual‐responsive surface wettability, which can be easily triggered by changing pH value or redox properties of the solution. A reversible conversion between superhydrophobicity and superhydrophilicity can be performed in a short time. The strategy used here may provide an easy method to control the wettability of smart surfaces by using properties of low‐cost functional polymers.

     

Two‐Dimensional Metal–Organic Framework Nanosheets for Membrane‐Based Gas Separation

Metal–organic framework (MOF) nanosheets could serve as ideal building blocks of molecular sieve membranes owing to their structural diversity and minimized mass‐transfer barrier. To date, discovery of appropriate MOF nanosheets and facile fabrication of high performance MOF nanosheet‐based membranes remain as great challenges. A modified soft‐physical exfoliation method was used to disintegrate a lamellar amphiprotic MOF into nanosheets with a high aspect ratio. Consequently sub‐10 nm‐thick ultrathin membranes were successfully prepared, and these demonstrated a remarkable H₂/CO₂ separation performance, with a separation factor of up to 166 and H₂ permeance of up to 8×10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at elevated testing temperatures owing to a well‐defined size‐exclusion effect. This nanosheet‐based membrane holds great promise as the next generation of ultrapermeable gas separation membrane.     

Thickness effects in naturally superhydrophilic TiO2–SiO2 nanocomposite films deposited via a multilayer sol–gel route

TiO₂–SiO₂ nanocomposite films of various thicknesses have been deposited via a multilayer sol–gel route. These films exhibit a natural and persistent superhydrophilicity, which allows considering new applications for easy to clean surfaces. Atomic force microscopy, scanning and transmission electron microscopy, as well as ellipsometry and UV/visible spectrometry measurements, were performed to study how the multilayer procedure influenced the morphology and composition of composite films in relation to their thickness. The natural and photo-induced wettability of these films was studied and discussed in relation to morphology, composition, and thickness features. It is concluded that, while such features did not significantly influence the natural wettability of nanocomposite films, their photo-induced wettability was considerably enhanced when increasing their thickness, which favored a faster superhydrophilicity photo-regeneration when this natural property started to disappear after a long aging period in ambient atmosphere.     

CO2‐Responsive Nanofibrous Membranes with Switchable Oil/Water Wettability

Responsive polymer interfacial materials are ideal candidates for controlling surface wetting behavior. Here we developed smart nanostructured electrospun polymer membranes which are capable of switching oil/water wettability using CO₂ as the trigger. In particular, the combination of CO₂‐responsiveness and porous nanostructure enables the as‐prepared membranes to be used as a novel oil/water on–off switch. We anticipate that the promising versatility and simplicity of this system would not only open up a new way of surface wettability change regulation by gas, but also have obvious advantages in terms of highly controlled oil/water separation and CO₂ applications.     

Ultrathin pH‐Sensitive Nanoporous Membranes for Superfast Size‐Selective Separation

Stimuli‐responsive nanoporous membranes have attracted increasing interest in various fields due to their abrupt changes of permeation/separation in response to the external environment. Here we report ultrathin pH‐sensitive nanoporous membranes that are easily fabricated by the self‐assembly of poly(acrylic acid) (PAA) in a metal hydroxide nanostrand solution. PAA‐adsorbed nanostrands (2.5–5.0 nm) and PAA‐Cu^II nanogels (2.0–2.5 nm) grow competitively during self‐assembly. The PAA‐adsorbed nanostrands are deposited on a porous support to fabricate ultrathin PAA membranes. The membranes display ultrafast water permeation and good rejection as well as significant pH‐sensitivity. The 28 nm‐thick membrane has a water flux decrease from 3740 to 1350 L m^?1 h^?1 bar^?1 (pH 2.0 to 7.0) with a sharp decrease at pH 5.0. This newly developed pH‐sensitive nanoporous membranes may find a wide range of applications such as controlled release and size‐ and charge‐selective separation.     

Hierarchical metal-phenolic-polyplex assembly toward superwetting membrane for high-flux and antifouling oil-water separation

Superwetting membranes have emerged as promising materials for the efficient treatment of oily wastewater. Typically, superwetting membranes can be developed by ingeniously chemical modification and topographical structuration of microporous membranes. Herein, we report the hierarchical assembly of metal-phenolic-polyplex coating to manipulate membrane surface superwettability by integrating metal-phenolic (Fe^III-tannic acid (TA)) assembly with polyplex (tannic acid-polyethylenimine (PEI)) assembly. The proposed Fe-TA-PEI coating can be deposited on microporous membrane via simply dipping into Fe^III-TA-PEI co-assembly solution. Based on the catechol chemistry, the coordination complexation of Fe^III and TA develops metal-phenolic networks to provide hydrophilic chemistries, and the electrostatic complexation of TA and PEI generates nanoconjugates to impart hierarchical architectures. Benefiting from the synergy of hydrophilic chemistries and hierarchical architectures, the resulting PVDF/Fe-TA-PEI membrane exhibits excellent superhydrophilicity (～0°), underwater superoleophobicity (～150°) and superior anti-oil-adhesion capability. The superhydrophilicity of PVDF/Fe-TA-PEI membrane greatly promotes membrane permeability, featuring water fluxes up to 5860 L m^?2 h^?1. The underwater superoleophobicity of PVDF/Fe-TA-PEI membrane promises potential flux (3393 L m^?2 h^?1), high separation efficiency (99.3%) and desirable antifouling capability for oil-in-water emulsion separation. Thus, we highlight the reported hierarchical metal-phenolic-polyplex assembly as a straightforward and effective strategy that enables the synchronous modulation of surface chemistry and topography toward superwetting membranes for promising high-flux and antifouling oil-water separation.     

Polydopamine Nanocluster Embedded Nanofibrous Membrane via Blow Spinning for Separation of Oil/Water Emulsions

Developing a porous separation membrane that can efficiently separate oil–water emulsions still represents a challenge. In this study, nanofiber membranes with polydopamine clusters polymerized and embedded on the surface were successfully constructed using a solution blow-spinning process. The hierarchical surface structure enhanced the selective wettability, superhydrophilicity in air (≈0°), and underwater oleophobicity (≈160.2°) of the membrane. This membrane can effectively separate oil–water emulsions, achieving an excellent permeation flux (1552 Lm⁻² h⁻¹) and high separation efficiency (~99.86%) while operating only under the force of gravity. When the external driving pressure was increased to 20 kPa, the separation efficiency hardly changed (99.81%). However, the permeation flux significantly increased to 5894 Lm⁻² h⁻¹. These results show that the as-prepared polydopamine nanocluster-embedded nanofiber membrane has an excellent potential for oily wastewater treatment applications.     

Uniformly Oriented Zeolite ZSM‐5 Membranes with Tunable Wettability on a Porous Ceramic

Facile fabrication of well‐intergrown, oriented zeolite membranes with tunable chemical properties on commercially proven substrates is crucial to broadening their applications for separation and catalysis. Rationally determined electrostatic adsorption can enable the direct attachment of a b‐oriented silicalite‐1 monolayer on a commercial porous ceramic substrate. Homoepitaxially oriented, well‐intergrown zeolite ZSM‐5 membranes with a tunable composition of Si/Al=25–∞ were obtained by secondary growth of the monolayer. Intercrystallite defects can be eliminated by using Na⁺ as the mineralizer to promote lateral crystal growth and suppress surface nucleation in the direction of the straight channels, as evidenced by atomic force microscopy measurements. Water permeation testing shows tunable wettability from hydrophobic to highly hydrophilic, giving the potential for a wide range of applications.     

Molecular Heterostructures of Covalent Triazine Frameworks for Enhanced Photocatalytic Hydrogen Production

Conjugated polymers have emerged as promising candidates for photocatalytic H₂ production owing to their structural designability and functional diversity. However, the fast recombination of photoexcited electrons and holes limits their H₂ production rates. We have now designed molecular heterostructures of covalent triazine frameworks to facilitate charge‐carrier separation and promote photocatalytic H₂ production. Benzothiadiazole and thiophene moieties were selectively incorporated into the covalent triazine frameworks as electron‐withdrawing and electron‐donating units, respectively, by a sequential polymerization strategy. The resulting hybrids exhibited much improved charge‐carrier‐separation efficiency as evidenced by photophysical and electrochemical characterization. An H₂ evolution rate of 6.6 mmol g^?1 h^?1 was measured for the optimal sample under visible‐light irradiation (λ>420 nm), which is far superior to that of most reported conjugated‐polymer photocatalysts.     

Host–Guest Chemistry Within Cellulose Nanocrystal Gel Receptors

Cellulose nanocrystals (CNCs) spontaneously assemble into gels when mixed with a polyionic organic or inorganic salt. Here, we have used this ion‐induced gelation strategy to create functional CNC gels with a rigid tetracationic macrocycle, cyclobis(paraquat‐p‐phenylene) ( CBPQT ⁴⁺). Addition of [ CBPQT ]Cl₄ to CNCs causes gelation and embeds an active host inside the material. The fabricated CNC gels can reversibly absorb guest molecules from solution then undergo molecular recognition processes that create colorful host–guest complexes. These materials have been implemented in gel chromatography (for guest exchange and separation), and as elements to encode 2‐ and 3‐dimensional patterns. We anticipate that this concept might be extended to design a set of responsive and selective gel‐like materials functioning as, for instance, water‐pollutant scavengers, substrates for chiral separations, or molecular flasks.     

Preparation of hierarchically structured PCL superhydrophobic membrane via alternate electrospinning/electrospraying techniques

Superhydrophobic polycaprolactone (PCL) membranes with hierarchical structure were fabricated via alternate electrospinning/electrospraying techniques. Electrospun PCL/methyl silicone oil (PCL/MSO) nanofibers were employed as substrate. PCL/MSO‐PCL microspheres (PCL/MSO‐PCL_MS) hierarchical membrane was prepared via electrosprayed PCL_MS as an additional layer on the substrate. Field emission scanning electron microscopy images showed the formation of hierarchical PCL/MSO‐PCL_MS membranes. Compared to pure PCL fibers substrate (120 ± 1.3°), the water contact angle (WCA) of MSO‐modified PCL membrane was 142 ± 0.7°. The most interesting observation was that the WCA of PCL_MS without any modification could be achieved to 146 ± 2.8°. On this basis, PCL/MSO‐PCL_MS hierarchical membrane possessed superhydrophobic surface with 150 ± 0.6° of WCA. The excellent surface roughness and air‐pocket capacity of hierarchical membranes would make the membranes more hydrophobic. The maximum oil (n‐hexane) adsorption capacity of PCL/MSO‐PCL_MS membrane was 32.53 g g^?1. Oil–water separation efficiencies of the superhydrophobic membranes were all higher than 99.93% after 10 cycles. The hierarchically structured PCL superhydrophobic membranes indicate the potential applications of environmentally friendly biopolymers as separation membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 421–430     

One‐Step Assembly of Phytic Acid Metal Complexes for Superhydrophilic Coatings

While of immense scientific interest, superhydrophilic surfaces are usually difficult to prepare, and preparation methods are typically substrate specific. Herein, a one‐step coating method is described that can endow superhydrophilicity to a variety of substrates, both inorganic and organic, using the coordination complexes of natural phytic acid and Fe^III ions. Coating deposition occurs in minutes, and coatings are ultrathin, colorless, and transparent. Superhydrophilicity is attributed, in part, to the high density of phosphonic acid groups. The ease, rapidness, and mildness of the assembly process, which is also cost‐effective and environmental‐friendly, points towards potential applications, such as self‐cleaning, oil/water separation, antifogging.     

Janus Copper Mesh Film with Unidirectional Water Transportation Ability toward High Efficiency Oil/Water Separation

Inspired by the special asymmetric wettability and controllable permeation function of cell membranes, we report a Janus nanostructured copper mesh film with unidirectional water transportation ability. Water can permeate from the hydrophobic side to the hydrophilic side, but is retained in the opposite direction. Notably, based on this special unidirectional water permeation property, both heavy oil/water mixtures (ρ _oil>ρ _water) and light oil/water mixtures (ρ _oil<ρ _water) can be separated. Additionally, the film demonstrates high separation efficiency and good recyclability. This paper reports a new Janus film that achieved highly efficient oil/water separation based on smart control of the wettability of the film. It is believed to have the potential to be used in many practical applications, such as wastewater treatment and oil‐spill cleanup.     

pH stimuli-responsive and fouling resistance PES membrane fabricated by using photochromic spiropyran and spironaphthoxazine nanofillers for pesticide removal

New fouling resistance and stimulus–responsive nanofiltration membranes were fabricated by adding photochromic spiropyran (SPO) and spironaphthoxazine (SNO) nanofillers to the polyethersulfone (PES) matrix via the phase inversion method. The effect of SPO and SNO, as novel photoresponsive molecule nanofillers, were evaluated in terms of membrane morphology, porosity, wettability, pure water flux (PWF), antifouling resistance, and stimulus–responsive properties. All the modified membranes indicated better performance compared to the bare PES. The membrane PWF was notably enhanced from 7.7 kg/m²h for the bare PES up to 18.68 and 20.58 kg/m²h for the 0.1 wt.% SPO and SNO blended membranes, respectively. Also, the 0.1 wt.% of SNO-based PES membrane indicated the best flux recovery ratio compared to the other membranes. The photo stimulus–responsive assessment showed a color change for both SPO and SNO photochromic in membranes. In the case of variable effect investigation, the response surface methodology at three levels (pressure: 4, 5, 6 bar and flow rate: 50, 100, and 150 L/h) was applied. A suitable flux (23.39 kg/m² h) and high removal efficiency (more than 90%) was achieved at optimum conditions. Also, the modified membranes by photochromic materials were sensitive to environmental variables such as acidic and alkaline conditions by changing their color.     

Formation of Ultrathin,Continuous Metal–Organic Framework Membranes on Flexible Polymer Substrates

Metal–organic framework (MOF) materials have an enormous potential in separation applications, but to realize their potential as semipermeable membranes they need to be assembled into thin continuous macroscopic films for fabrication into devices. By using a facile immersion technique, we prepared ultrathin, continuous zeolitic imidazolate framework (ZIF‐8) membranes on titania‐functionalized porous polymeric supports. The coherent ZIF‐8 layer was surprisingly flexible and adhered well to the support, and the composite membrane could sustain bending and elongation. The membranes exhibited molecular sieving behavior, close to the theoretical permeability of ZIF‐8, with hydrogen permeance up to 201×10^?7 mol m^?2 s^?1 Pa^?1 and an ideal H₂/CO₂ selectivity of 7:1. This approach offers significant opportunities to exploit the unique properties of MOFs in the fabrication of separation and sensing devices.     

Formation of Ultrathin,Continuous Metal–Organic Framework Membranes on Flexible Polymer Substrates

Metal–organic framework (MOF) materials have an enormous potential in separation applications, but to realize their potential as semipermeable membranes they need to be assembled into thin continuous macroscopic films for fabrication into devices. By using a facile immersion technique, we prepared ultrathin, continuous zeolitic imidazolate framework (ZIF‐8) membranes on titania‐functionalized porous polymeric supports. The coherent ZIF‐8 layer was surprisingly flexible and adhered well to the support, and the composite membrane could sustain bending and elongation. The membranes exhibited molecular sieving behavior, close to the theoretical permeability of ZIF‐8, with hydrogen permeance up to 201×10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ and an ideal H₂/CO₂ selectivity of 7:1. This approach offers significant opportunities to exploit the unique properties of MOFs in the fabrication of separation and sensing devices.     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

A General Strategy for the Separation of Immiscible Organic Liquids by Manipulating the Surface Tensions of Nanofibrous Membranes

Oil/water separation membranes with different wettability towards water are attractive for their economic efficiency and convenience. The key factor for the separation process is the roughness‐enhanced wettability of membranes based on the intrinsic wetting threshold (IWT) of water, that is, the limitation of the wettability caused by hydrophobicity and hydrophilicity. However, the separation of organic liquids (OLs) remains a challenge. Herein, we manipulate the surface tensions of nanofibrous membranes to lie between the IWTs of the two OLs to be separated so that the nanofibrous membranes can be endowed with superlyophobicity and superlyophilicity for the two liquids, and thus lead to successful separation. Our investigations provide a general strategy to separate any immiscible liquids efficiently, and may lead to the development of membranes with a large capacity, high flux, and high selectivity for organic reactions or liquid extraction in chemical engineering.     

Chitosan/polyvinyl alcohol/amino functionalized multiwalled carbon nanotube pervaporation membranes: Synthesis,characterization, and performance

In the present study, novel biodegradable nanocomposite membranes were prepared by adding the amino functionalized multiwalled carbon nanotube (NH₂‐MWCNT) to the chitosan/polyvinyl alcohol blend polymers, and the obtained membranes were used for dehydration of isopropyl alcohol through pervaporation process. For this purpose, the membranes were prepared with chitosan/polyvinyl alcohol ratio of 4:1 on the basis of “solution casting” method and then crosslinked using glutaraldehyde, after addition of different amounts of NH₂‐MWCNT. The prepared membranes were characterized using scanning electron microscopy, contact angle, mechanical strength, degree of swelling (DS), and biodegradability. Also, the ability of the prepared membranes in dehydration of isopropyl alcohol was determined using pervaporation experiments. Results indicated that contact angle, mechanical resistance, separation factor (α), and pervaporation separation index were increased with the addition of NH₂‐MWCNT up to 10 wt% (relative to the total amount of polymer) and then decreased in the higher presence of nanotubes (15 wt%). Furthermore, the DS and permeate flux were first decreased and then increased for the same mentioned amounts of additive. In this study, optimized membrane was obtained by the addition of 10 wt% NH₂‐MWCNT. This membrane showed the maximum α (99.5), pervaporation separation index parameter (78.29 kg m⁻² h⁻¹), biodegradability, and mechanical stability as well as minimum DS.     

Fabrication of a Hydrogen‐Bonded Organic Framework Membrane through Solution Processing for Pressure‐Regulated Gas Separation

Ordered and flexible porous frameworks with solution processability are highly desirable to fabricate continuous and large‐scale membranes for the efficient gas separation. Herein, the first microporous hydrogen‐bonded organic framework (HOF) membrane has been fabricated by an optimized solution‐processing technique. The framework exhibits the superior stability because of the abundant hydrogen bonds and strong π–π interactions. Thanks to the flexible HOF structure, the membrane possesses the unprecedented pressure‐responsive H₂/N₂ separation performance. Furthermore, the scratched membrane can be healed by the treatment of solvent vapor, achieving the recovery of separation performance.