Search criteria and rules for comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry analysis of airborne particulate matter

Direct thermal desorption-gas chromatography-time-of-flight mass spectrometry (DTD-GC-TOFMS) and comprehensive two-dimensional (2D) gas chromatography-time-of-flight mass spectrometry (GC x GC-TOFMS) was applied for characterisation of semi-volatile organic compounds (SVOC) in fine particulate matter (PM), with a diameter of up to 2.5 microm (PM2.5), from ambient air in Augsburg, Germany. DTD-GC-TOFMS measurements on the SVOC in PM2.5 are done on a daily basis (time series over several years). The data will be used in an epidemiological study questioning the influence of SVOC in PM2.5 on ambient aerosol related health effects. The outcome of the first measurements periods is that the organic inventory in the ambient aerosol can undergo drastic fluctuations, e.g. due to meteorological influences or specific emission sources. This includes also the large fraction of chromatographically not resolved peaks (unresolved carbonaceous matter (UCM)). The UCM fraction contains about 70% of the SVOC mass in PM2.5. GC x GC-TOFMS is a suited technique to study the nature of the yet unidentified compounds forming the UCM. The considerably increased chromatographic resolution in GC x GC allows separation of many UCM compounds while the TOFMS supplies mass spectral data of all separated compounds. However, the data sets are getting enormously complex. In a typical PM2.5 sample from Augsburg more than 15,000 peaks can be detected. Thus, it is important to classify the observed GC x GC peaks by rational means. A classification procedure based on GC x GC retention times and the fragmentation patterns is suggested. With a preliminary classification procedure it is already possible to group compounds with some certainty into substance classes. After some further development, this approach can be used for classifying GC x GC data, e.g. for environmental and epidemiological studies.     

Analysis of aromatic compounds in gasoline with flow-switching comprehensive two-dimensional gas chromatography

A comprehensive two-dimensional gas chromatography (GC x GC) instrument has been created by coupling a flow-switching modulator and a standard gas chromatograph. The instrument was used to characterize the aromatic composition of gasoline. The high-resolution separation produced by flow-switching GC x GC allowed gasoline aromatics to be fully resolved from saturated components. The aromatic compounds were further separated into groups having the same carbon number. A standard gasoline sample was analyzed to evaluate the quantitative accuracy and precision of this technique. The data show that flow-switching GC x GC produces results that are comparable to gas chromatography-mass spectrometry (GC-MS) and thermal modulation GC x GC. The simple, low-cost, and robust nature of flow-switching GC x GC makes it an ideal technique for the routine analysis of aromatic compounds in gasoline.     

On-line multi-bed sorption trap for VOC analysis of large-volume vapor samples: injection plug width, effects of water vapor and sample decomposition

A multibed on-line sorption trap is used to preconcentrate organic vapors from air samples and inject the analytes into a GC separation column. Injection plug widths depend on the boiling point for the lipophilic compounds and on the polarity and boiling point for the polar compounds. Injection plug widths are sufficiently small (0.7-0.8 s) as to allow the direct injection of the most volatile compounds into the GC column without the need for a second focusing device. The presence of water in the samples has an effect on the retention of polar compounds by the trap. However, this effect is reproducible for a fixed water content and so can be overcome by using calibration standards under the same conditions of humidity as the samples. The thermal decomposition of many volatile organic compounds in an on-line sorption trap during the GC analysis of air samples is examined. The results show that degradation of unstable compounds is governed by the amount of heat transferred to the compounds during desorption (i.e., applied temperature and pulse duration). The use of an on-line trap results in the immediate transfer of desorbed compounds to the analytical column, which can reduce the formation of artifacts.     

Investigation of sulphur compounds in coal tar using monodimensional and comprehensive two-dimensional gas chromatography

Coal is a non renewable fossil fuel, used mainly as a source of electrical energy and in the production of coke. It is subjected to thermal treatment, pyrolysis, which produces coke as a main product, in addition to a condensed liquid by-product, called tar. Tar is a complex mixture of organic compounds which contains different chemical classes, presenting aromatic and sulphur heterocyclic compounds. In general, identification of these compounds requires steps of isolation and fractionation, mainly due to co-elution of these compounds with polyaromatic hydrocarbons (PAH). The objective of this work is to characterize the sulphur compounds present in the coal tar obtained via pyrolysis, using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). Coal samples from the State of Paraná, Brazil were subjected to laboratorial scale pyrolysis. Several experimental conditions were tested, such as sample weight (5, 10 and 15g), heating ramp (10, 25 and 100°C/min) and final temperature (500, 700 and 900°C). Samples were analyzed by one dimensional gas chromatography (1D-GC) coupled to a quadrupole mass spectrometry detector (GC/qMS) and two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). The higher amount of sulphur compounds was obtained at a final temperature of 700°C and a heating ramp of 100°C/min. The main classes observed in the color plot were thiophenes, benzothiophenes and alkylated dibenzothiophenes. GC×GC/TOFMS allowed the identification of the greater number of compounds and the separation of several sulphur compounds from one another. Moreover, separation of sulphur compounds from polyaromatic hydrocarbons and phenols was achieved, which was not possible by 1D-GC. Comparing GC×GC/TOFMS and 1D-GC (SIM mode) also showed that 1D-GC, one of the most employed quantification tools for sulphur compounds, can be misleading for detection, identification and quantification, as the number of isomers of sulphur compounds found was greater than theoretically possible.     

Comparison of two-stage retention index monitoring capillary gas chromatography and selected ion monitoring capillary gas chromatography – mass spectrometry as analytical tools

Two-stage capillary GC with two-stage retention index monitoring is an efficient analytical technique which can be used for detection and determination of small amounts of volatile compounds in complex mixtures of hundreds or thousands of other compounds. The system employs two capillary columns, coated with different stationary phases, connected on-line with the aid of a micro valve; the first column acts as a pre-separating unit from which unresolved fractions of interest are cut (transferred) into another column for final, interference-free separation of the compounds to be determined. This technique has been compared with selected ion monitoring capillary GC-MS using a hydrocarbon mixture as a test sample for comparing resolution, repeatability, and the practical usefulness of the techniques. Results indicate that two-stage capillary GC is very useful for mixtures containing compounds which produce mostly non-specific ions in the MS ion source whereas compounds producing specific ions can be easily analyzed by capillary GC – single ion monitoring MS even if they are not perfectly separated by a single capillary column.     

Comprehensive two-dimensional gas chromatography/mass spectrometric analysis of pepper volatiles

The headspace compositions of 13 pepper and peppercorn samples of different species, colloquially also referred to as pepper, were analyzed, and more than 300 compounds were tentatively characterized by means of comprehensive two-dimensional gas chromatography in tandem with flame ionization detection, quadrupole mass spectrometric detection and time-of-flight mass spectrometric detection (GC x GC-FID, GC x GC/qMS and GC x GC/TOFMS, respectively). The analysis of volatile organic compounds (VOCs) was performed after solid-phase microextraction (SPME) using a 75-microm PDMS/DVB fibre. Fingerprint comparison between the three techniques permitted peaks to be assigned in the GC x GC-FID experiment based on the analogous MS analysis, taking into account retention shifts arising from method variations. When using GC x GC/TOFMS, about five times more peaks were identified than in GC x GC/qMS. Retention indices for all peaks were calculated in the bi-dimensional column set comprising of a 5% phenyl polysilphenylene-siloxane primary column and a polyethylene glycol second column. The spectra obtained by both mass detection techniques (qMS and TOFMS) give very similar results when spectral library searching was performed. The majority of the identified compounds eluted as pure components as a result of high-resolution GC x GC separations, which significantly reduces co-elution, and therefore increases the likelihood that pure spectra can be obtained. The differences between TOFMS and qMS (in fast scanning mode) spectra were generally small. Whilst spectral quality and relative ion ratios across a narrow peak (e.g. w(b) approximately 100-150 ms) do vary more for the fast peaks obtained in GC x GC/qMS operation, than with TOFMS, in general adequate spectral matching with the library can be achieved.     

Projection of multidimensional GC data into alternative dimensions—exploiting sample dimensionality and structured retention patterns

Comprehensive multidimensional gas chromatography (GC×GC) is a powerful separation technique. One of the features of this technique is that it offers separations with more apparent structure than that offered by conventional one-dimensional GC (1-D GC). While some previous studies have alluded to this structure, and used structured retention patterns for some simple classifications, the topic of structured retention in GC×GC has not been studied in any great detail. Using the separation of fatty acid methyl esters (FAME) on both nonpolar/polar and polar/nonpolar column sets, the interaction between the separation dimensions and the sample dimensions is explored here. The GC×GC separation of a series of compounds is presented as a projection of the sample from sample space, a p-dimensional space with dimensions defined by the dimensionality of the sample, into separation space: for GC×GC, a two-dimensional plane passing through the sample space in an orientation defined by the separation conditions. Using this conceptual model and some a priori knowledge of the sample, it is shown how the image of the sample in the separation space can be used to construct an image of the sample in alternate dimensions, such as second dimension retention factor (²k) vs. chain length in the case of FAME. These projections into alternate dimensions should facilitate the interpretation of the complex patterns found within the GC×GC chromatogram for the identification and classification of compounds.     

气提吸附／热脱附／气相色谱－质谱法分析污水中的痕量有机物

采用气提吸附／热脱附／气相色谱－质谱法对齐鲁公司所处地区工业污水进行分析。方法采用Ｔｅｎａｘ－ＧＣ吸附剂对样品进行气提吸附，脱附时样品直接进入色谱仪汽化室，一次进样即可完成全组分分析，共检测出含四氯丙醚在内的４０种有机组分，测定了各组分的程序升温保留指数。气相色谱－质谱法测定出四氯丙醚三个异构体的结构。     

Universal and discriminative detection using a miniaturized pulsed discharge detector in comprehensive two-dimensional GC

A miniaturized pulsed discharge detector (Mini-PDD) has been successfully demonstrated for comprehensive 2-D GC (GC x GC) analysis of pyrolysis gasoline and the pyrolysis GC x GC analysis of a polyethylene copolymer. The detector cell volume of the Mini-PDD is reduced to 25% of the Valco plug-in PDD D-3. An n-C11 peak width at base is 96 ms for the Mini-PDD, about 23% larger than a peak width of 78 ms detected by a flame ionization detector (FID). The Mini-PDD has sufficient response time for most GC x GC applications. When Mini-PDD is operated in helium photoionization mode (Mini He-PDD), it is a universal detector for both inorganic and organic compounds. This is especially useful when detection of water is needed in GC x GC applications. When krypton is doped in the helium discharge gas (Mini Kr-PDD), it can suppress signals of compounds having higher ionization potentials and enhance relative signal intensities of aromatic compounds. The determination of aliphatic to aromatic hydrocarbon ratios is essential to the operation of petroleum crackers. Comparison of the signal from two modes of the Mini-PDD is a simple and fast way to verify the location of aromatics in comprehensive 2-D gas chromatograms.     

Identification of volatiles from pineapple (Ananas comosus L.) pulp by comprehensive two-dimensional gas chromatography and gas chromatography/mass spectrometry

Combining qualitative data from the chromatographic structure of 2-D gas chromatography with flame ionization detection (GC×GC-FID) and that from gas chromatography-mass spectrometry (GC/MS) should result in a more accurate assignment of the peak identities than the simple analysis by GC/MS, where coelution of analytes is unavoidable in highly complex samples (rendering spectra unsuitable for qualitative purposes) or for compounds in very low concentrations. Using data from GC×GC-FID combined with GC/MS can reveal coelutions that were not detected by mass spectra deconvolution software. In addition, some compounds can be identified according to the structure of the GC×GC-FID chromatogram. In this article, the volatile fractions of fresh and dehydrated pineapple pulp were evaluated. The extraction of the volatiles was performed by dynamic headspace extraction coupled to solid-phase microextraction (DHS-SPME), a technique appropriate for slurries or solid matrices. Extracted analytes were then analyzed by GC×GC-FID and GC/MS. The results obtained using both techniques were combined to improve compound identifications.     

Global and selective detection of organohalogens in environmental samples by comprehensive two-dimensional gas chromatography-tandem mass spectrometry and high-resolution time-of-flight mass spectrometry

We successfully detected halogenated compounds from several kinds of environmental samples by using a comprehensive two-dimensional gas chromatograph coupled with a tandem mass spectrometer (GC×GC-MS/MS). For the global detection of organohalogens, fly ash sample extracts were directly measured without any cleanup process. The global and selective detection of halogenated compounds was achieved by neutral loss scans of chlorine, bromine and/or fluorine using an MS/MS. It was also possible to search for and identify compounds using two-dimensional mass chromatograms and mass profiles obtained from measurements of the same sample with a GC×GC-high resolution time-of-flight mass spectrometer (HRTofMS) under the same conditions as those used for the GC×GC-MS/MS. In this study, novel software tools were also developed to help find target (halogenated) compounds in the data provided by a GC×GC-HRTofMS. As a result, many dioxin and polychlorinated biphenyl congeners and many other halogenated compounds were found in fly ash extract and sediment samples. By extracting the desired information, which concerned organohalogens in this study, from huge quantities of data with the GC×GC-HRTofMS, we reveal the possibility of realizing the total global detection of compounds with one GC measurement of a sample without any pre-treatment.     

GC FPD method for the simultaneous speciation of butyltin and phenyltin compounds in waters

A method is described for the simultaneous determination of nanogram amounts of mono-, di- and tri-butyltin compounds in water. The procedure is based on the conversion of tin compounds to volatile species by Grignard pentylation and analysis using GC with flame photometric detection (GC FPD). The ionic compounds are extracted from diluted acidified (HBr) aqueous solutions by using a pentane-tropolone solution. The extracted organotin compounds are pentylated by a Grignard reagent and purified on a Fluorisil column before analysis by GC FPD. The detection limits are 20 ng dm^?3 for butyltin compounds and 50 ng dm^?3 for phenyltin compounds. Recoveries from spiking experiments in tap-water and natural seawater matrices, in which no organotin compounds were detected, were greater than 90% for most of the alkyltin compounds.     

Improved determination of flavour compounds in butter by solid-phase (micro)extraction and comprehensive two-dimensional gas chromatography

The practicability and potential of comprehensive two-dimensional gas chromatography (GC x GC) coupled to both conventional flame ionisation (FID) and time-of-flight mass spectrometric (TOF-MS) detection, were compared with those of conventional one-dimensional (1D) GC, with the determination of flavour compounds in butter as an application. For polar flavour compounds, which were collected from the aqueous fraction of butter by means of solid-phase extraction (SPE), it was found that GC x GC dramatically improves the overall separation. Consequently, quantification and preliminary identification based on the use of ordered structures, can be performed more reliably. The improvement effected by replacing 1D-GC by GC x GC is considerable also in the case of TOF-MS detection, as illustrated by the high match factors generally obtained during identification. GC x GC was also used successfully for the characterisation of volatile flavour compounds in the headspace of butter collected by solid-phase microextraction (SPME) and to study the effect of heat treatment on the composition of butter samples in more detail.     

Qualitative supercritical fluid extraction coupled to capillary gas chromatography

The usefulness and ease of utilizing supercritical fluid extraction (SFE) directly coupled to capillary gas chromatography (GC) as quantitative or qualitative analytical problem-solving tools will be demonstrated. As an alternative to conventional liquid solvent extractions, SFE presents itself as a means to achieve high extraction efficiencies of different compounds in complex solid matrices in very rapid tims frames. Moreover, SFE has an additional advantage of being able to achieve distinct extraction selectivities as a function of the solubilizing power of the supercritical fluid extracting phase. For on-line SFE/GC, the extraction effluent is directly transferred to the analytical chromatograph. On-line SFE/GC involves the decompression of pressurized extraction effluent directly into a heated, unmodified capillary split injection port of the GC. In this respect, SFE introduction into GC can be used as an alternative means of GC injection, comparable to such modes of injection as pyrolysis and thermal desorption. This paper will show applications of SFE/GC where mass spectrometric detection together with flame ionization detection was used for component identification from environmental, tobacco, and petroleum matrices.     

全二维气相色谱/飞行时间质谱用于柴油组成的研究

将全二维气相色谱法(GC×GC)用于柴油馏分的组成分布研究,建立了两种GC×GC方法,一种用于柴油组成的详细表征,另一种用于柴油族组成的快速分离和定量,两种方法均不需要样品预处理。用前一种方法对柴油馏分中的烃类化合物、主要的含硫化合物与含氮化合物组成进行了研究;对催化裂解柴油中的27种含氮化合物和42种含硫化合物进行了定性;用后一种方法在70 min内即可完成柴油馏分族组成的定量分析,应用所建立的方法测定了4个不同来源的柴油馏分中非芳烃、一环芳烃、二环芳烃、三环芳烃的含量,定量结果与ASTM D2425法     

Qualitative screening and quantitative determination of pesticides and contaminants in animal feed using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry

A method has been developed for the target analysis of over 100 pesticides and contaminants in a complex feed matrix. The method is based on extraction with ethyl acetate, cleanup by gel permeation chromatography (GPC) and dispersive solid-phase extraction (SPE) with primary secondary amine phase (PSA), and analysis by comprehensive two-dimensional gas chromatography with full scan time-of-flight mass spectrometric detection (GC x GC-TOF-MS). Parameters studied during method development included a dispersive SPE cleanup step after GPC, large volume injection into the GC system and the GC x GC separation. Qualitative and quantitative performance of the GC x GC system was evaluated by analyzing spiked extracts in the range equivalent to 1-100 microg/kg in feed. At levels of 50 microg/kg and higher, all compounds targeted for could be identified fully automatically by the software based on their mass spectra. At lower levels the hit rate decreased with the concentration. System linearity was excellent in solvent and only slightly affected by matrix (correlation coefficients r>or=0.995 for 90% of the compounds). Limits of quantification were in the 1-20 microg/kg range for most compounds. The overall method was validated for 106 compounds at the 10 and 100 microg/kg level. Recoveries between 70% and 110% and RSDs below 20% were obtained for the majority of the compounds.     

Combination of dynamic time warping and multivariate analysis for the comparison of comprehensive two-dimensional gas chromatograms: application to plant extracts

Comprehensive two-dimensional gas chromatography (GC x GC) is now recognized as the preferred technique for the detailed analysis and characterization of complex mixtures of volatile compounds. However, for comparison purposes, taking into account all the information contained in the chromatogram is far from trivial. In this paper, it is shown that the combination of peak alignment by dynamic time warping and multivariate analysis facilitated the comparison of complex chromatograms of tobacco extracts. The comparison is shown to be efficient enough to provide a clear discrimination among three types of tobacco. A tentative interpretation of loadings is presented in order to give access to the compounds which differ from one sample to another. Once located, mass spectrometry was used to identify markers of tobacco type.     

A Glimpse of Recent Developments in Brazilian Analytical Chemistry

Geting bituminous coal (GBC) was exhaustively extracted with isometric carbon disulfide/acetone at ambient temperature to provide twenty extracts and a residue. The extracts were characterized by gas chromatography/mass spectrometry (GC/MS), Fourier transform infrared spectroscopy, and atmospheric pressure solids analysis probe time-of-flight mass spectrometry. GBC and its residue were observed with a scanning electron microscope. The total extract yield is ca. 11.5%. The GC/MS-detectable compounds in extract 1 can be classified into alkanes, cyclanes, arenes, cyclenes, and heteroatomic compounds, among which arenes are predominant. The number of detected compounds decreases and they have higher molecular masses with increasing extraction times. The combination of multiple techniques facilitates understanding the molecular composition of the extractable species from coals.     

固相微萃取-气相色谱/质谱测定植物叶片中的挥发性物质

采用固相微萃取（SPME)方法吸附植物叶片中的挥发性物质,然后采用气相色谱/质谱法（GC/MS）分析了挥发性物 质的成分。在45 ℃水浴温度下,采用Polyacrylate(85 μm)固相微萃取头,在广口瓶中植物叶片的上方顶空吸附60 min,然后进行GC/MS分析。结果表明,植物叶片中的挥发性物质得到了很好的分离,受山楂叶螨(Tetraychus vienneis) 危害严重的植物的完好叶片中的挥发性物质均含有顺-3-己烯-1-醇乙酸酯、顺-3-己烯-1-醇丁酸酯和α-法呢烯,且含量 较大。初步确定这些物质是对山楂叶螨具有引诱作用的主要物质,从而为利用天然生物活性物质防治山楂叶螨提供了理论 依据。     

Dispersive liquid-liquid microextraction method based on solidification of floating organic drop combined with gas chromatography with electron-capture or mass spectrometry detection

A simple dispersive liquid-liquid microextraction (DLLME) method based on solidification of a floating organic drop (DLLME-SFO) technique combined with gas chromatography/electron-capture detection (GC/ECD) or gas chromatography/mass spectrometry (GC/MS) has been developed. The proposed method is simple, low in cost, and of high precision. It overcomes the most important problem in DLLME, the high-toxic solvent used. Halogenated organic compounds (HOCs) in water samples were determined as the model compounds. The parameters optimized for the DLLME-SFO technique were as follows: A mixture of 0.5 mL acetone, containing 10 microL 2-dodecanol (2-DD-OH), was rapidly injected by syringe into the 5 mL water sample. After centrifugation, the fine 2-DD-OH droplets (8+/-0.5 microL) were floated at the top of the screwcap test tube. The test tube was then cooled in an ice bath. After 5 min the 2-DD-OH solvent had solidified and was then transferred into a conical vial; it melted quickly at room temperature and 3 microL (for GC/ECD) or 2 microL (for GC/MS) of it was injected into a gas chromatograph for analysis. The limit of detection (LOD) for this technique was 0.005-0.05microgL(-1) for GC/ECD and was 0.005-0.047 microgL(-1) for GC/MS, respectively. The linear range of the calibration curve of DLLME-SFO was from 0.01 to 500 microgL(-1) with a coefficient of estimation (r2)>0.996 for GC/ECD and was from 0.02 to 500 microgL(-1) with a coefficient of estimation (r2)>0.996 for GC/MS.