Nonextractable cyanopropyl polysiloxane stationary phases for capillary chromatography

Summary Crosslinkable cyanopropylpolysiloxane stationary phases have been difficult to produce because of steric effects of the large cyanopropyl groups or because of the interaction between the polar cyanopropyl groups and the groups added for crosslinking. Various polymers containing 50% to 90% cyanopropyl were synthesized which contained vinyl,p-tolyl, or 4-vinylphenyl groups for crosslinking. Thep-tolyl group was found to give satisfactory crosslinking if there were two such groups attached to one silicon atom.     

Synthesis of siloxane stationary phases for capillary gas chromatography and supercritical fluid chromatography

A comparison is made between dichlorosilanes and cyclic siloxanes as starting materials in the synthesis of stationary phases for capillary gas chromatography (CGC) and supercritical fluid chromatography (SFC). Siloxanes containing one or more of the side groups methyl, vinyl, phenyl, and cyanoethyl in various ratios were synthesized and compared. These phases were characterized by chromatographic (gel permeation, GPC), spectroscopic (IR, ¹H NMR, ²⁹Si NMR), and thermal (DSC) methods. Coated fused silica columns were evaluated with respect to polarity, crosslinkability with several free-radical initiators, and thermal stability. A new liquid phase, 7% cyanoethyl, 7% phenyl, 1% vinyl methyl polysiloxane is shown to be more polar than OV-1701, more temperature stable, easily crosslinked and suitable for use in supercritical fluid chromatography.     

Crosslinked methylphenylsilicones as stationary phases for capillary gas chromatography

Summary Methyl(phenyl)silicones offer useful selectivities when used as stationary phases in gas chromatography (GC). Such phases have, however, hitherto been of restricted importance in capillary GC due to the lack of phases having a viscosity high enough to ensure stationary phase film stability. Further, to utilize fully the possibilities of a methyl(phenyl)silicone capillary column, it must also possess high efficiency and a high degree of deactivation.In this work, the preparation of soda-glass capillary columns coated within situ cured methyl(phenyl) and methyl(tolyl)-silicones is presented. Vulcanization was made possible by the introduction of some vinyl substitution in the gum to be cured: tolyl-containing gums could be cured without the presence of vinyl groups. In addition, fused silica capillary columns coated with OV-1701 were prepared.The columns show a coating efficiency of above 80%, a thermal stability up to 320 °C and a high degree of deactivation. Their utility is demonstrated by the separation of samples containing polynuclear aromatics, antidepressants and some potent mutagens.Presented at the 14th International Symposium on Chromatography London, September, 1982     

Investigation of the role of adsorption at the stationary phase interface in capillary columns prepared with cross-linked phases

Summary On the basis of the adsorption-absorption additivity theory the influence of adsorption on the retention of polar samples has been quantitatively studied using fused-silica capillary columns coated with nonpolar cross-linked and non-cross-linked liquid stationary phases. It is shown that cross-linking of a nonpolar stationary phase increases the contribution of adsorption to the retention of polar compoments. As a result the retention of polar compounds increases on crosslinked stationary phases as compared with the initial (non cross-linked) phase. “The material of this paper was presented at the 15th International Symposium on Chromatography, Nürnberg, October, 1984”     

Autocrosslinkable methyl-2-phenylethylpolysiloxane stationary phase for capillary column gas chromatography

Methyl-2-phenylethylpolysiloxane polymers have been synthesized for comparison with methylphenylpolysiloxane stationary phases for gas chromatography. The 50% 2-phenylethyl polysiloxane was found to be autocrosslinkable at 260°C without addition of free redical initiator. Although the selectivity of this phase appears to be similar to the 50% phenyl polysiloxane, its thermal stability is not as high.     

Azo compounds for free radical crosslinking of polysiloxane stationary phases

There has been much effort spent in recent years developing the technology for free radical crosslinking of polysiloxane polymers to prepare capillary columns coated with thermally stable and nonextractable stationary phases. Organic peroxides have been used extensively as the free radical initiators for the in situ polymerization of the stationary phases. However, these peroxides adversely affect the phase polarity and column activity. Seven azo compounds were studied for crosslinking efficiency. Azo compounds can be used as free radical initiators to prepare nonextractable stationary phases without the adverse effects caused by peroxides.     

冠醚修饰型手性固定液的合成及其气相色谱性能的研究

合成了两种含冠醚功能基的手性固定液：（１Ｓ,２Ｓ）－１－对硝基苯基－２－（４＇－西佛碱基苯并１５－冠－５）－丙烷－１,３－烯丙氧基聚硅氧烷和３－甲基－２－（４＇－甲酰胺－苯并１５－冠－５）－丁酸乙酯。用它们涂制的石英毛细管柱呈强极性,色谱性能良好。并探讨了固定液的结构对分离能力的影响。     

Flexible soft glass capillary columns vs. flexible fused silica capillary columns for gas chromatography-a critique

The gas chromatographic use of flexible thin walled soft glass capillary columns coated with non-polar stationary phases is compared to similar columns made of fused silica glass. With non-polar soft glass columns, the use of surface roughening viagaseous HCI followed by a Carbowax 20 M pretreatment gave adsorptive phenomena, and thermal instability. With very polar soft glass columns where a variety of cyanopropyl silicone phases were coated directly onto the NaCI crystal matrix, adsorptive effects were again prominent and frequent break-down in film stability with time, was also observed. These undesirable effects were due to the presence of metal oxides in the soft glass. Attempts to remove these materials from the thin walled soft glass surface by means of acid leaching produced significant brittleness. This deleterious result was further increased by attempts at high temperature silylation or polysiloxane deactivation. In sharp contrast, the fused silica surface was essentially free of metal oxides and the surface silanol groups are easily neutralized by silylation or polysiloxane deactivation techniques. No brittleness was observed following these procedures. An increasing series of high molecular weight, viscous, polymeric vinyl containing non-polar and highly polar stationary phases have been produced which readily wet the surface of the fused silica and are easily crosslinked in the presence of free radical generators. These columns are essentially free of all the problems noted with flexible thin walled soft glass. When all of the parameters involved in the fabrication of a glass capillary column are assessed, it appears at this time, that the flexible fused silica glass column with cross linked phases approaches the “ideal” capillary column.     

Photovoltaic properties of the polymer solar cells comprising crosslinked maleimide polymers and fullerene‐derivative PCBM

A series of crosslinkable maleimide conjugated polymers with different vinyl group contents as side‐chain crosslinking sites have been synthesized by the Suzuki coupling reaction. Polymer solar cells (PSCs) were fabricated based on an interpenetrating network of the crosslinkable maleimide polymers as the electron donor, and a fullerene derivative, (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), as the electron acceptor. The crosslinkable maleimide polymers underwent crosslinking reaction at the side‐chain vinyl groups upon the thermal treatment with or without the addition of initiator, azobisisobutyronitrile (AIBN). Better photovoltaic (PV) performances were obtained for the PSCs based on the polymer crosslinking without using initiator, whereas poorer PV performances were observed for the PSCs based on the polymer crosslinking with the AIBN initiator. In addition, higher operational stability was observed for the crosslinked polymer based solar cell as compared to the solar cell based on the un‐crosslinked polymer. The photo‐physical and PV properties of the cross‐linked maleimide polymers/PCBM based PSCs are discussed in detail as the morphology and crosslinking density of the polymers are taken into account. Copyright © 2010 John Wiley & Sons, Ltd.     

Aptamer stationary phase for protein capture in affinity capillary chromatography

The thrombin-binding DNA aptamer was used with thrombin as a model system to investigate protein capture using aptamer stationary phases in affinity capillary chromatography. The aptamer was covalently attached to the inner surface of a bare fused-silica glass capillary to serve as the stationary phase. Proteins were loaded onto the capillary via an applied pressure. The capillary was then washed to remove unbound and non-specifically associated proteins. Finally, the bound protein was released and eluted using 20 mM Tris buffer containing 8 M urea, pH 7.3, at 50 degrees C. Eluate was collected after each step (load, wash and elute) and relative amounts of protein each were compared using fluorescence spectroscopy. The identity of the protein in the collections was confirmed using matrix assisted laser desorption ionization-time-of-flight (MALDI-TOF) mass spectrometry. The experiment was repeated for thrombin on a bare (unmodified) capillary and a capillary coated with a scrambled-sequence, non-G-quartet forming oligonucleotide that does not bind with thrombin. The results show that the aptamer stationary phase captures approximately three times as much thrombin as the control columns. The experiment was also repeated using human serum albumin (HSA) alone and in an equimolar mixture with thrombin. HSA was not retained on the aptamer capillary, nor did it affect the capture of thrombin from the mixture.     

Application of capillary supercritical fluid chromatography to the analysis of a middle distillate fuel

Summary The application of capillary supercritical fluid chromatography (SFC) to the analysis of a middle distillate fuel is described. Small diameter (50m i.d.) fused-silica capillary columns coated with crosslinked 50% phenyl polymethylphenyl siloxane provided high separation efficiency and good compatibility with flame ionization detection. High resolution separations of the chemical class fractions obtained by adsorption chromatography on alumina were obtained using carbon dioxide as the supercritical mobile phase and simple pressure programming techniques. In addition to the less polar fuel components, supercritical carbon dioxide allowed chromatography of the nitrogen-containing polycyclic aromatic hydrocarbon fraction and the hydroxylated polycyclic aromatic materials.     

一种非晶硅膜改性弹性玻璃毛细管交联中等极性固定相色谱柱的制备

研究了非晶硅膜改性的弹性玻璃毛细管交联ＯＶ－１７０１中等极性固定相色谱柱。在适当温度下，采用过氧化二异丙苯（ＤＣＵＰ）游离基引发交联ＯＶ－１７０１固定液，成功地制备了交联ＯＶ－１７０１柱，该柱具有柱效高、惰性好、耐溶剂、抗腐蚀和耐高温等性能，是一种新型高性能的中等极性交联柱。     

Siloxane/silarylene copolymers as stationary phases for capillary gas chromatography. Part II: Phenylsubstituted polymers

A commercially available silanol terminated silicone stationary phase, OV-61-OH (33% phenyl), and two phenyl-substituted siloxane/silarylene copolymers, Sila 3 (27% phenyl) and 4 (35% phenyl), have been evaluated for use as stationary phases in fused silica capillary columns for gas chromatography. Ulterations in column adsorptive activity, separation efficiency, stationary phase film thickness and selectivity after column conditioning for 50 h at 370°C have been studied. A high thermal stability was experienced with the stationary phases tested here. For OV-61-OH, the best thermal stability was obtained when coated on untreated fused silica, which illustrates the importance of grafting reactions here. The heat treatment resulted in some deactivation of adsorptive sites in the column. A higher degree of column deactivation was achieved when surface silylation was performed prior to coating. High thermal stability was achieved with Sila 3 when coated on such surfaces. Sila 3 would thus be preferred in cases when high thermal stability in combination with high dsorptive inertness is desired. Sila 4 showed low column bleeding at 370 °C, but prolonged heating at this temperature resulted in the broadening of n-alkane peaks when eluted at 90 °C. This indicates that excessive crosslinking has taken place during the heat treatment and the minimum allowable column operation temperature is thereby increased to ca. 120 °C. The separation of aza-arenes and of triglycerides are shown as applications.     

Synergistic effect of resorcarene and cyclodextrin mixed stationary phase in gas chromatography

Summary A new resorcarene derivatives, ethylhexylresorcarene, was synthesized and used as stationary phase in opentubular (capillary) columns. It was combined with heptakis(2,6-di-O-pentyl-3-O-trifluoroacetyl)-β-CD and coated on fused-silica capillary tubes. By studying the chromatographic properties of the mixed stationary phase and its selectivity for different isomers, as well as comparing with the resorcarene and the CD used as individual stationary phases, a synergistic effect was observed on the mixed stationary phase.     

Capillary gas chromatography of hydrogenation products of 1,5,9-cyclododecatriene stereoisomers

Summary The separation of the products obtained by the hydrogenation of 1,5,9-cyclododecatriene stereoisomers on fused-silica capillary columns coated with dimethylsilicone and cyanopropylmethylsilicone stationary phases was investigated. Retention indices of cyclododecatrienes, cyclododecadienes, cyclododecenes and cyclododecane were determined at three temperatures. The respective standard deviations were 0.3 and 0.6 i.u. The influence of the polarity of the stationary phases on the chromatographic retention of these cyclic hydrocarbones is discussed.     

Gas chromatography of tricyclic spiro esters

Summary The separation of some tricyclic spiro esters on fused-silica capillary columns coated with dimethylsiloxane, cyanopropyl methyl siloxane and poly(ethylene glycol) stationary phases was investigated. Retention indices were determined at two temperatures to interpret their chromatographic behaviour. The repeatability of the measurements was 0.2, 0.3 and 0.5 index units. The influence of the polarity of the stationary phases on the chromatographic retention of these tricyclic spiro esters is discussed.     

Preparation of thermostable,phenyl silicone coated,glass capillary columns for separation of polyaromatic hydrocarbons

Summary A procedure for the preparation of glass capillary columns coated with non-extractable phenyl polysiloxanes has been developed, the phenyl silicone being synthesised in situ in the column. The non-extractability can be explained in terms of a certain degree of crosslinking in the polymer and possibly also by some chemical bonding to the capillary glass wall. Rearrangement of the film at higher temperatures is counteracted by crosslinking in the phase. Column bleeding is thus decreased, and column efficiency is maintained even at higher temperatures. Such capillary columns showed suitable selectivities for separation of polyaromatic hydrocarbons, and the high temperatures necessary for these analyses could be attained.     

Polymerization of allyl(vinyl phenyl) ethers and reactions of the resulting polymers

Solution polymerizations of allyl(o-vinyl phenyl)ether and allyl(p-vinyl phenyl)ether with cationic and radical initiators were investigated. Soluble polymers were formed in polymerizations with boron trifluoride etherate and with benzoyl peroxide. In polymerization with azobisisobutyronitrile the polymerization in dilute solution gave a soluble polymer, whereas that in concentrated solution gave a crosslinked, insoluble one. For informationon the polymerization behavior some infrared and ultraviolet spectroscopic investigations of the soluble polymers were made. From these results it appears that polymers with pendant allyl groups are formed in polymerization with boron trifluoride etherate at low temperature, and polymers containing pendant vinyl groups and allyl groups are obtained with the two types of radical initiator. Copolymerizations of these monomers with ethyl vinyl ether and styrene with the use of boron trifluoride etherate were sucessfully effected. Such reactions as Claisen rearrangement, crosslinking induced with radical initiators, and epoxidation with perbenzoic acid were examined for the polymers prepared in the polymerization with boron trifluoride etherate. Good results were obtained for the former two reactions. However, the latter was unsuccessful.     

高分子冠醚毛细管柱的性能研究

本文报道了3种新的聚硅氧烷侧链冠醚作气相色谱固定液,并涂渍成弹性石英毛细管柱,这种毛细管柱具有优良的色谱性能,它们具有柱效高,热稳定性好,选择性强的特点,适于分离各种异构体。     

Chromatographic properties of tetramethyl-p-silphenylene-dimethyl,diphenylsiloxane copolymers as stationary phases for gas-liquid chromatography

Seven tetramethyl-p-silphenylene-dimethyl, diphenylsiloxane copolymers were coated on fused-silica capillary columns to evaluate their properties as stationary phases in gas-liquid chromatography. The capillary columns were tested concerning their selectivity, separation efficiency, column bleed, inertness, elution temperatures, and working range. The following characteristic properties of the silphenylene unit were found: (i) the impact of the silphenylene group on the chromatographic selectivity is similar to that of two dimethylsiloxy groups and half of a diphenylsiloxy group; (ii) silphenylene-siloxane copolymers offer reduced column bleed and increased maximum allowable operating temperature in comparison to polysiloxanes, since the backbone stiffing phenylene group enhances thermal stability; (iii) the elution temperatures of analytes are increased by 15-30 degrees C on silphenylene-siloxane copolymers compared to polysiloxanes; (iv) the silphenylene unit increases the glass transition temperature of the polymers resulting in elevated minimum allowable operating temperatures.