Comparative study of optimised BCR sequential extraction scheme and acid leaching of elements in the certified reference material NIST 2711

The optimised BCR sequential extraction procedure and a 4 h 1 mol L⁻¹ HCl partial extraction have been performed on the NIST 2711 reference material for a suite of 12 elements (Cd, Sb, Pb, Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, As) using magnetic sector ICP-MS. A pseudo-total aqua regia digest of NIST 2711 has also been undertaken for quality assurance purposes, and comparison of the sum of the four BCR fractions, which included an aqua regia digest on the residue, with the pseudo-total aqua regia digest has been used to assess the accuracy of the BCR partitioning approach. As a result of this work, discrepancies between previous studies about BCR partitioning of elements in NIST 2711 have been discussed and an increase in confidence about the use of BCR partitioning scheme on seven elements (Cd, Pb, Al, Mn, Fe, Cu, Zn) in this standard material has been obtained. On the other hand, BCR partitioning for Sb, Cr, Co, Ni and As has been provided for the first time. Partial extraction results are also reported for the same 12 elements analysed by the optimised BCR procedure, with the partial extraction results exhibiting a strong correlation with the sum of the three labile steps of the BCR procedure.     

Comparison of metal analysis in sediments using EDXRF and ICP-OES with the HCl and Tessie extraction methods

The work presents an investigation on metal availability in sediments during 13 months using the dispersive-energy X-ray fluorescence (EDXRF) and atomic emission spectrometry with induced argon plasma (ICP-OES) techniques and single extraction (0.1 mol l⁻¹ HCl) and Tessie’s sequential speciation methods. The EDXRF technique could yield essentially the same profile as ICP-OES for the seasonal variation of metals in sediments, but in a more practical way. The sequential extraction procedure (SEP) was more efficient in metal dissolution than single extraction. The Pb, Ni, Al, Cr, and Fe elements were less efficiently extracted with single extraction in relation to sequential extraction. For Co both methodologies were equivalent, but for Cu and Mn the extraction was higher with single extraction. Single extraction does not mobilize Pb, Ni, Al, Cr, and Fe adsorbed on oxides and bound to organic matter. However for Cu and Mn, not only extracted these metals from the four fractions, but it also dissolved part of the fifth fraction (residual). Principal Component Analysis discriminated seasonal variations in the content of several metals, mainly Fe, Co, Ni, and Zn. The mobility of metallic ions in the sediments is conditioned to the seasonal flow of organic and inorganic material coming from the river or by the erosion of adjacent soils.     

Comparison of original and modified BCR sequential extraction procedures for the fractionation of copper, iron, lead, manganese and zinc in soils and sediments

This article describes a detailed comparison between the original BCR sequential extraction procedure, step 2 of which involves treatment with 0.1 mol l⁻¹ hydroxylammonium chloride at pH 2, and the revised BCR procedure (step 2: 0.5 mol l⁻¹ hydroxylammonium chloride at pH 1.5). An intermediate protocol was also evaluated in which 0.5 mol l⁻¹ hydroxylammonium chloride at pH 2 was used. The procedures were applied to five soil and sediment substrates: a sewage sludge-amended soil, two different industrially contaminated soils, a river sediment and an inter-tidal sediment. Extractable iron and manganese concentrations were measured to assess the effects of the procedural modifications on dissolution of the reducible matrix components. Trace elements copper, lead and zinc were also determined. Statistical analysis (two-tailed t-tests at 95% confidence interval) indicated that recovery of iron in step 2 was not markedly enhanced when the intermediate protocol was used. However, significantly greater amounts were isolated with the revised BCR scheme than with the original procedure. Copper behaved similarly to iron. Lead recoveries were increased by use of both modified protocols, with the greatest effect occurring for the revised BCR extraction. In contrast, manganese and zinc extraction did not vary markedly between procedures. The work indicates that the revised BCR sequential extraction provides better attack on the iron-based components of the reducible matrix for a wide range of soils and sediments.     

Determination of bioavailable fractions of Zn, Cu, Ni, Pb and Cd in soils and sludges by atomic absorption spectrometry

The single extraction procedures validated by the standards, measurement and testing programme (formerly BCR), extraction with 0.05 mol l⁻¹ EDTA and 0.43 mol l⁻¹ acetic acid, have been applied to reference materials of soils and sludges with certified total values of elements, in order to determine bioavailable contents of Cd, Cu, Ni, Pb and Zn. These soils, which represent uncontaminated pedologically different types of soils from Slovakia and sludges from city water treatment are characterized for the bioavailable fraction of the metals using the procedures followed by SM&T Programme. Concentrations of the elements under the study in the extracts were determined by flame (FAAS) using calibration curves in appropriate extractants and by electrothermal (ETAAS) atomic absorption spectrometry, using technique of standard additions for the evaluation of the results. The accuracy of the extraction procedures and determinations of the elements in the extracts was controlled using CRM 483 certified for EDTA- and acetic acid-extractable contents of Cd, Cu, Ni, Pb and Zn in sewage sludge amended soil.     

Should acid ammonium oxalate replace hydroxylammonium chloride in step 2 of the revised BCR sequential extraction protocol for soil and sediment?

The revised, four-step BCR sequential extraction for soil or sediment has been compared with an alternative procedure in which 0.2 mol l⁻¹ ammonium oxalate (pH 3) replaced 0.5 mol l⁻¹ hydroxylammonium chloride (pH 1.5) in step 2, the reducible step. A variety of substrates were studied: BCR CRM601, a sewage sludge amended soil, two industrial soils, and a steel manufacturing by-product (basic oxygen furnace filter cake). Greater amounts of iron were recovered in step 2 when acid ammonium oxalate was used, for all substrates. Similar trends were observed for copper. Manganese and zinc were not strongly affected by the procedural modification, except for zinc in the two industrial soils, where oxalate extraction proved more efficient than use of hydroxylammonium chloride. A large proportion of the calcium and lead isolated in step 2 of the BCR procedure was not released until step 3 when the alternative procedure with oxalate in step 2 was used. This is probably due to rapid precipitation of analyte oxalates from solution. Thus, whilst oxalate offers superior dissolution of iron-containing matrix components, it should not be used if calcium or lead concentrations are to be measured. Selection of the most appropriated sequential extraction protocol for use in a particular study must always be carried out on the basis of “fitness for purpose” criteria. However, the revised BCR protocol, involving use of 0.5 mol l⁻¹ NH₂OH·HCl in the reducible step, appears to be more generally applicable than procedures involving acid ammonium oxalate.     

Assessment of trace metals contamination in estuarine sediments using a sequential extraction technique and principal component analysis

Fractionation of the metals Cd, Cr, Cu, Ni, Pb and Zn in sediments was performed for samples collected from eight locations in the Poxim river estuary of Sergipe State, northeast Brazil, using the 3-stage sequential extraction procedure proposed by the European Community Bureau of Reference (BCR). The extraction method was found to be satisfactory for analysis of certified reference material BCR-701, with recovery values ranging from 85% (Cu) to 117% (Cr). The detection limits obtained were 0.001 to 0.305 µg g^− 1. Zn exhibited greatest mobility and bioavailability, indicative of anthropogenic sources, while Cr was mainly found in the residual fraction and could be used as an indicator for the contribution from natural sources. Cd, Cu, Ni and Pb were associated with the oxidizable fraction, and Pb, Cr and Ni with the reducible fraction. Principal component analysis (PCA) clearly separated the metals into three groups: I (Zn); II (Pb); III (Cd, Cu, Cr and Ni). These groupings were mainly due to different distributions of the metals in the various fractions, in sediments from the different locations. Risk assessment code (RAC) analysis indicated that although the metals presented a moderate overall risk to the aquatic environment, nickel showed a low risk (RAC < 10%) at three sites, while zinc presented a high risk (RAC > 30%) at four other sites.     

Assessment of CaCl2, NaNO3 and NH4NO3 extraction procedures for the study of Cd, Cu, Pb and Zn extractability in contaminated soils

The variety of extraction procedures used in environmental studies makes it very difficult to compare the results obtained; therefore, harmonisation and standardisation is required. The extraction of heavy metals from soil by un-buffered salt solutions is a method used to estimate soil contamination and trace metal availability to plants. The present study assesses three of these methods. All the three methods are standardised or is undergoing standardisation in Europe: 0.01 mol l⁻¹ CaCl₂ (The Netherlands), 0.1 mol l⁻¹ NaNO₃ (Switzerland) and 1 mol l⁻¹ NH₄NO₃ (Germany). The soil-reference material BCR CRM 483, with indicative values for CaCl₂, NaNO₃, NH₄NO₃ extractable metals, was analysed for quality control purposes. The three methods were also applied to 10 contaminated soils and the extracted metals (Cd, Cu, Pb, and Zn) were determined. The procedures were found to be precise (typically <10%) for all metals, taking into account the low metal concentrations extracted. The metal extraction efficiency obtained with each procedure was slightly different, and the three methods provided equivalent information while predicting the relative trace-metal mobility (Cd>Zn>Cu>Pb) in the soils studied. From the experience obtained, the 0.01 mol l⁻¹ CaCl₂ extraction procedure seems to be the most suitable method for performing a harmonisation process, since this procedure combines an appropriate extraction capacity for this type of studies with the lowest salt concentration in the extracts and, consequently, with a more simple matrix for metal determination.     

Liquid-liquid extraction and recovery of indium using Cyanex 923

The extraction of In(III) from HCl, H₂SO₄, and HNO₃ media using a 0.20 mol l⁻¹ Cyanex 923 solution in toluene is investigated. In(III) is quantitatively extracted over a fairly wide range of HCl molarity while from H₂SO₄ and HNO₃ media the extraction is quantitative at low acid concentration. The extracted metal ion has been recovered by stripping with 1.0 mol l⁻¹ H₂SO₄. The stoichiometry of the In(III): Cyanex 923 complex is observed to be 1:2. The extraction of In(III) is insignificantly changed in diluents namely toluene, n-hexane, kerosene (160-200 °C), cyclohexane, and xylene having more or less the same dielectric constants, whereas, it decreases with increasing polarity of diluents such as cyclohexanone and chloroform. The extractant is stable towards prolonged acid contact and there is a negligible loss in its extraction efficiency even after recycling for 20 times. The extraction behavior of some commonly associated metal ions namely V(IV), Ti(IV), Al(III), Cr(III), Fe(III), Ga(III), Sb(III), Tl(III), Mn(II), Fe(II), Cu(II), Zn(II), Cd(II), Pb(II), and Tl(I) has also been investigated. Based on the partition data the conditions have been identified for attaining some binary separations of In(III). These conditions are extended for the recovery of pure indium from zinc blend, zinc plating mud, and galena. The recovery of the metal ions is around 95% with purity approximately 99%.     

Ultrasound-Assisted Extraction for the Evaluation of Element Mobility in Bottom Sediment Collected at Mining and Smelting Pb–Zn Ores Area in Poland

The current BCR procedure for metal fractionation recommended by the Standard Measurement and Testing Programme requires rather time-consuming sample pretreatment. Ultrasonic energy seems to be an attractive alternative for leaching metal from solid samples into a liquid extractant phase. This study aims at optimizing ultrasonic extraction in order to replace the BCR method of leaching using acetic acid and to apply the procedure of assessing element mobility in bottom sediment rich in moderately soluble carbonate minerals. The application of ICP-MS allowed the determination of As, Cd, Cr, Cu, Pb, Ni, Tl and Zn in extracts, in a wide range of concentration without any special treatment. Finally, 40’min extraction in an ultrasonic bath was proposed for evaluation of the mobile fraction of As, Cd, Cr, Cu, Pb and Zn as an assessment of environmental risk. The recovery of the ultrasound-assisted extraction in comparison to the shake-filter method, as applied in the common BCR procedure, was slightly higher than 100% for As, Cr and Pb, reasonably high (about 70%) for Cd, Zn and Cd, but did not exceed 21% for Tl. Also, the mobility and extractability (relative mobility) of the studied elements from sediment collected over one year were compares. According to the results obtained after 40’min of ultrasound-assisted extraction it can be concluded that mobility did not change over one year for Cr, Cu, As, Cd, Ni and Tl, but noticeable differences for Zn and Pb were observed. The total content of all studied elements was almost the same in samples taken in the years 2003 and 2004, respectively.     

Solid phase extraction of zinc(II) using a PVC-based polymer inclusion membrane with di(2-ethylhexyl)phosphoric acid (D2EHPA) as the carrier

A polymer inclusion membrane (PIM) is reported consisting of 45% (m/m) di(2-ethylhexyl)phosphoric acid (D2EHPA) immobilized in poly(vinyl chloride) (PVC) for use as a solid phase absorbent for selectively extracting Zn(II) from aqueous solutions in the presence of Cd(II), Co(II), Cu(II), Ni(II) and Fe(II). Interference from Fe(III) in the sample is eliminated by precipitation with orthophosphate prior to the extraction of Zn(II). Studies using a dual compartment transport cell have shown that the Zn(II) flux (2.58 × 10⁻⁶ mol m⁻² s⁻¹) is comparable to that observed for supported liquid membranes. The stoichiometry of the extracted complex is shown to be ZnR₂·HR, where R is the D2EHPA anion.     

Antimony-film electrode for the determination of trace metals by sequential-injection analysis/anodic stripping voltammetry

The possibility of applying antimony-film modified glassy carbon electrode in sequential-injection analysis (SIA) was investigated with the objective of determining Pb(II) and Cd(II) by anodic stripping voltammetry (ASV). The conditions of antimony-film deposition concerning composition of the plating/carrier solutions, concentrations of Sb(III) and hydrochloric acid, effects of different supporting electrolyte salts, and plating potential were optimized. It was found that the antimony-film deposition on glassy carbon substrate in a sample solution consisting of 750 μg L⁻¹ Sb(III), 0.5 mol L⁻¹ HCl at −1.5 V (vs. Ag/AgCl/3 mol L⁻¹ KCl) yielded a modified electrode suitable for the determination of Pb(II) and Cd(II) at the μg L⁻¹ level. The reproducibility of the analytical signals was characterized by a relative standard deviation lower than 2.8%, and the calculated values of detection limits were 1.2 μg L⁻¹ for Pb(II) and 1.4 μg L⁻¹ for Cd(II). The presence of KSCN in the sample solution offers the possibility of detecting ions with more negative oxidation potentials like Zn(II), Mn(II) or Cr(III). The developed SIA-ASV procedure was compared with the commonly used batch method, and its applicability was tested on a spiked tap water sample.     

Assessment of heavy metals leachability from metallo-organic sorbent-iron humate-with the aid of sequential extraction test

The sequential extraction test, known as a BCR procedure, was used to assess a leachability of heavy metals (Zn, Cd, Pb, Cu) from the metallo-organic sorbent—iron humate—loaded with these metals. The sequential test allowed to discriminate between various fractions of heavy metals, namely the acid-extractable fraction, the fraction bound to Fe oxides, and the fraction bound to organic matter. It was proven that the heavy metals are bound mainly to Fe oxides and organic matter, and thus they may be relatively hardly liberated into the environment. The BCR sequential extraction test exhibited a very good repeatability, when it was applied to the loaded sorbent—relative standard deviations were typically lower than 10%.     

Ligandless cloud point extraction of Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II) ions in environmental samples with Tween 80 and flame atomic absorption spectrometric determination

A cloud point extraction (CPE) procedure has been developed for the determination trace amounts of Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II) ions by using flame atomic absorption spectrometry. The proposed cloud point extraction method was based on cloud point extraction of analyte metal ions without ligand using Tween 80 as surfactant. The surfactant-rich phase was dissolved with 1.0 mL 1.0 mol L⁻¹ HNO₃ in methanol to decrease the viscosity. The analytical parameters were investigated such as pH, surfactant concentration, incubation temperature, and sample volume, etc. Accuracy of method was checked analysis by reference material and spiked samples. Developed method was applied to several matrices such as water, food and pharmaceutical samples. The detection limits of proposed method were calculated 2.8, 7.2, 0.4, 1.1, 0.8 and 1.7 μg L⁻¹ for Cr(III), Pb(II), Cu(II), Ni(II), Bi(III), and Cd(II), respectively.     

Solid phase extractive preconcentration of trace metals using p-tert-butylcalix[4]arene-1,2-crown-4-anchored chloromethylated polymeric resin beads

5,11,17,23-Tetrakis(1,1-dimethylethyl)-25,26-dihydroxy-27,28-crown-4-calix[4]arene in the cone conformation was synthesized. This p-tert-butylcalix[4]arene-1,2-crown-4 compound was then anchored with Merrifield chloromethylated resin beads. The modified polymeric resin was characterized by ¹H NMR, FT-IR and elemental analysis and used successfully for the separation and preconcentration of Cu(II), Cd(II), Co(II), Ni(II) and Zn(II) prior to their determination by FAAS. Effective extraction conditions were optimized in both batch and column methods. The resin exhibits good separating ability with maximum between pH 6.0-7.0 for Cu(II), pH 6.0 for Cd(II), pH 5.0 for Co(II), pH 4.0-4.5 for Ni(II), and pH 4.5 for Zn(II). The elution studies were carried out with 0.5 mol L⁻¹ HCl for Cu(II), Co(II) and Co(II), 1.0 mol L⁻¹ HCl for Cd(II) and Zn(II). The sorption capacity, preconcentration factor and distribution coefficient of each metal ion were determined. The detection limits were 1.10, 1.25, 1.83, 1.68 and 2.01 μg L⁻¹ for Cu(II), Cd(II), Co(II), Ni(II) and Zn(II). The influence of several ions on the resin performance was also investigated. The validity of the proposed method was checked for these metal ions in NIST standard reference material 2709 (San Joaquin Soil) and 2711 (Montana Soil).     

Artifacts in the Determination of Trace Metal Binding Forms in Anoxic Sediments by Sequential Extraction

Abstract

The binding forms of Co, Cd, Cu, Pb, and Zn in an anoxic, sulfide-bearing sediment were investigated by performing both thermodynamic equilibrium calculations and sequential extractions. Care was taken to maintain oxygen-free conditions during the whole experiment. The calculations suggested that trace metals were bound to sulfidic minerals. Sequential extraction results, however, showed increased importance of exchangeable and reducible fractions in the order Cu < Cd < Pb < Zn < Co. Thermodynamic equilibrium calculations of the chemical reactions during extraction showed that Cd, Co, Pb, and Zn sulfides are to a significant extent soluble in the acetate-exchangeable (step 1 + 2) and oxalate-reducible (step 3) fractions. Neglecting the dissolution of sulfide minerals would lead to a misinterpretation of the experimental results.     

Chemically modified silica gel with p-dimethylaminobenzaldehyde for selective solid-phase extraction and preconcentration of Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II) by ICP-OES

Silica gel-bound amines phase modified with p-dimethylaminobenzaldehyde (p-DMABD) was prepared based on chemical immobilization technique. The product (SG-p-DMABD) was used as an adsorbent for the solid-phase extraction (SPE) Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II) prior to their determination by inductively coupled plasma optical emission spectrometry (ICP-OES). The uptake behaviors of SG-p-DMABD for extracting these metal ions were studied using batch and column procedures. For the batch method, the optimum pH range for Cr(III) and Ni(II) extraction was ≥ 3, for Cu(II), Pb(II) and Zn(II) extraction it was ≥ 4. For simultaneous enrichment and determination of all the metals on the newly designed adsorbent, the pH value if 4.0 was selected. All the metal ions can be desorbed with 2.0 mL of 0.5 mol L^− 1 of HCl. The results indicate that SG-p-DMABD has rapid adsorption kinetics using the batch method. The adsorption capacity for these metal ions is in the range of 0.40-1.15 mmol g^− 1, with a high enrichment factor of 125. The presence of commonly coexisting ions does not affect the sorption capacities. The detection limits of the method were found to be 1.10, 0.69, 0.99, 1.10 and 6.50 μg L^− 1 for Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was 5.0% (n = 8) for all metal ions. The method was applied to the preconcentration of Cr(III), Cu(II), Ni(II), Pb(II) and Zn(II) from the certified reference material (GBW 08301, river sediment) and water samples with satisfactory results.     

A new and direct method for the trace element determination in cauliflower by differential pulse polarography

Using the DPP polarograms of wet digested cauliflower sample in acetate buffer at pH values of 2, 4 and 6, Fe, Zn, Mo, Se, Cr, Cd, Pb, Ti and Cu quantities were determined. The best separation and determination conditions for Zn, Se and Mo was pH 2; for Cr, Zn, Mo and As was pH 4; for Pb pH 6, for Ti, Cu and Fe was pH 6-7 EDTA, for Cd pH 2 EDTA and for lead pH 6, all in acetate buffer. The trace element ranges for cauliflowers from two different seasons were (first figure for winter, the second for summer) for Se 120-250 μg g⁻¹, Fe 70-85 μg g⁻¹, Cu 320-150 μg g⁻¹, Ti 90-120 μg g⁻¹, Cr 130-630 μg g⁻¹, Zn 90-550 μg g⁻¹, Mo 170-230 μg g⁻¹, Cd 20 μg g⁻¹ (in winter) and Pb 130-300 μg g⁻¹ in dry sample. Cd was under the detection limit in summer. The length of digestion time had no effect on the recovery of copper, iron, molybdenum and zinc between 15 and 3 h of digestion.     

An rhodamine-based fluorescence probe for iron(III) ion determination in aqueous solution

An “off-on” rhodamine-based fluorescence probe for the selective signaling of Fe(III) has been designed exploiting the guest-induced structure transform mechanism. This system shows a sharp Fe(III)-selective fluorescence enhancement response in 100% aqueous system under physiological pH value and possesses high selectivity against the background of environmentally and biologically relevant metal ions including Al(III), Cd(II), Fe(II), Co(II), Cu(II), Ni(II), Zn(II), Mg(II), Ba(II), Pb(II), Na(I), and K(I). Under optimum conditions, the fluorescence intensity enhancement of this system is linearly proportional to Fe(III) concentration from 6.0 × 10⁻⁸ to 7.2 × 10⁻⁶ mol L⁻¹ with a detection limit of 1.4 × 10⁻⁸ mol L⁻¹.     

Multivariate optimization by exploratory analysis applied to the determination of microelements in fruit juice by inductively coupled plasma optical emission spectrometry

A method for the direct determination (without sample pre-digestion) of microelements in fruit juice by inductively coupled plasma optical emission spectrometry has been developed. The method has been optimized by a 2³ factorial design, which evaluated the plasma conditions (nebulization gas flow rate, applied power, and sample flow rate). A 1:1 diluted juice sample with 2% HNO₃ (Tetra Packed, peach flavor) and spiked with 0.5 mg L^− 1 of Al, Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Sb, Sn, and Zn was employed in the optimization. The results of the factorial design were evaluated by exploratory analysis (Hierarchical Cluster Analysis, HCA, and Principal Component Analysis, PCA) to determine the optimum analytical conditions for all elements. Central point condition differentiation (0.75 L min^− 1, 1.3 kW, and 1.25 mL min^− 1) was observed for both methods, Principal Component Analysis and Hierarchical Cluster Analysis, with higher analytical signal values, suggesting that these are the optimal analytical conditions. F and t-student tests were used to compare the slopes of the calibration curves for aqueous and matrix-matched standards. No significant differences were observed at 95% confidence level. The correlation coefficient was higher than 0.99 for all the elements evaluated. The limits of quantification were: Al 253, Cu 3.6, Fe 84, Mn 0.4, Zn 71, Ni 67, Cd 69, Pb 129, Sn 206, Cr 79, Co 24, and Ba 2.1 µg L^− 1. The spiking experiments with fruit juice samples resulted in recoveries between 80 and 120%, except for Co and Sn. Al, Cd, Pb, Sn and Cr could not be quantified in any of the samples investigated. The method was applied to the determination of several elements in fruit juice samples commercialized in Brazil.     

Chromium available fractions in arousa sediments using a modified microwave BCR protocol based on microwave assisted extraction

In a research of chromium availability, the three-stage sequential extraction procedure, proposed by European Community Bureau of Reference (BCR), has been applied for the metal fractionation in marine sediment samples. The procedure has been modified, evaluating the effect of microwave energy to perform the sequential method. Results achieved a substantial reduction in time in comparison to the traditional shaking technique. The time of the first and the second extractions were reduced to 30 s in both steps using microwave heating and working at 66 W of power. To the third extraction, higher power was necessary so it was chosen to work at 198 W. In the last step investigated, time was reduced to 1 min, being a great improvement respect to the conventional BCR sequential extraction protocol.Chromium determinations in these extracts were carried out by Electrothermal Atomic Absorption Spectrometry (ETAAS). The developed method was applied for chromium determination in marine sediment samples from Ria de Arousa (Galicia, NW of Spain). The values obtained by our laboratory ranged from 0.10 to 1.02 μg g⁻¹ for soluble and reducible fractions, and from 5.5 to 60.0 μg g⁻¹ for the oxidisable fraction. The higher concentrations obtained were the chromium associated with the organic fraction of the marine sediments.