Solid-phase extraction of polar compounds with a hydrophilic copolymeric sorbent

A new synthesized copolymer based on N-vinylimidazole-divinylbenzene (VIm-DVB) was tested as a sorbent for the solid-phase extraction (SPE) of polar analytes. In the on-line SPE, this synthesized sorbent enabled 100 ml of sample to be preconcentrated with recoveries as high as 80% for oxamyl, phenol (Ph) and derivates, bentazone and (4-chloro-2-methylphenoxy)acetic acid (MCPA). For the off-line SPE, 1000 ml of sample was extracted and recoveries were higher than 92% for all compounds with the exception of oxamyl (83%) and methomyl (78%). The VIm-DVB sorbent gives better recoveries than the previously synthesized 4-vinylpyridine-divinylbenzene (VP-DVB) resin and similar to such highly crosslinked commercial sorbents as LiChrolut EN or Oasis HLB. Real water samples were used to validate the on-line SPE method. Linearity was good and detection limits were between 0.1 and 0.2 microg l(-1).     

Comparison of several solid-phase extraction sorbents for continuous determination of amines in water by gas chromatography-mass spectrometry

A semiautomatic method has been proposed for the determination of different types of amines in water samples including anilines, chloroanilines, N-nitrosamines and aliphatic amines. The analytes were retained on a solid-phase extraction sorbent column and after elution, 1 μL of the extract was analysed by gas chromatography coupled with electron impact ionization mass spectrometry. A systematic overview is given of the advantages and disadvantages of several sorbents (LiChrolut EN, Oasis HLB, RP-C₁₈, graphitized carbon black, fullerenes and nanotubes) in the retention of amine compounds and based on sensitivity, selectivity and reliability. The retention efficiency for the studied amines was higher (ca. 100%) with LiChrolut EN and Oasis HLB than it was with RP-C₁₈ and fullerenes (53 and 62%, respectively, on average). Detection limits of 0.5-16 ng L⁻¹ for the 27 amines studied were obtained when using a sorbent column containing 75 mg of LiChrolut EN for 100 mL of sample, the RSD being lower than 6.5%. The method was applied with good accuracy and precision in the determination of amines in various types of water including river, pond, tap, well, drinking, swimming pool and waste.     

New hydrophilic polymeric resin based on 4-vinylpyridine-divinylbenzene for solid-phase extraction of polar compounds from water

A 4-vinylpyridine-divinylbenzene (VP-DVB) resin was synthesized to be used for on-line solid-phase extraction process and it was tested for a group of polar compounds. The high specific surface area and the nitrogen content of the VP-DVB sorbent increased the interactions with the polar analytes in the preconcentration process. The sorbent enabled 100 ml of water to be concentrated with recoveries higher than 70% for several polar compounds (including phenol) except for oxamyl (55%) and methomyl (43%). The method was used to analyse water samples by liquid chromatography and UV detection. Linearity was good and detection limits were 0.1-0.2 microg l(-1) for all compounds. Several tap and river water and waste water treatment plant samples were analyzed; phenol and (4-chloro-2-methyl-phenoxy)acetic acid (MCPA) were tentatively determined in some samples.     

Evaluation of a new hypercrosslinked polymer as a sorbent for solid-phase extraction of polar compounds

A new hypercrosslinked polymer (HXLGp) with hydrophilic character due to the presence of hydroxyl moieties has been tested as a sorbent for the solid-phase extraction (SPE) of several polar compounds from water samples. This new sorbent enables the on-line extraction of 300 ml of sample with recoveries higher than 80% for polar compounds such as oxamyl, methomyl or desisopropylatrazine (DIA). The HXLGp has also been compared to other commercially available sorbents such as Oasis HLB (hydrophilic macroporous), to hydrophobic hypercrosslinked resins and to a previously synthesized sorbent based on N-vinylimidazole-divinylbenzene. The results are consistently better with the new synthesized sorbent. The method was successfully applied to the on-line SPE-HPLC of tap and river water samples. The validation with river water samples provided good linearity range and detection limits between 0.03 for methomyl and 4-nitrophenol (4NP) to 0.2 microg l(-1) for phenol (Ph).     

Ultra-trace-level determination of polar pesticides and their transformation products in surface and estuarine water samples using column liquid chromatography-electrospray tandem mass spectrometry.

A method is developed for the determination of polar pesticides and their transformation products [atrazine, deethylatrazine, deisopropylatrazine, hydroxyatrazine, diuron, 3,4-dichlorophenylmethylurea, 3,4-dichlorophenylurea (DPU), monuron, bentazone, anthranil-isopropylamide, chloridazon, metolachlor] in surface, estuarine and sea water samples at the low ng/l level. Solid-phase extraction is combined off-line with column liquid chromatography-electrospray ionization tandem mass spectrometric detection (LC-ESI-MS-MS). The applicability of two solid-phase materials, i.e., LiChrolut EN cartridges and graphitized carbon black extraction disks, is evaluated. The influence of the organic solvent used in gradient LC, as well as the amount of co-extracted humic material on the ESI process is studied. The eluotropic strength of the organic solvent was found to have a distinct effect on the sensitivity of ESI-MS if coupled with LC gradient separations. Methanol gave much better results than acetonitrile and phenylurea compounds are more susceptible to solvent changes than triazines. Co-extracted humic material causes signal suppression in ESI-MS-MS detection. The degree of suppression depends upon the sample pH and the nature of the samples, i.e., surface or estuarine water. Detection limits in LC-ESI-MS-MS ranged from 0.2 to 2 ng/l, with the exception of DPU (8 ng/l). The applicability of the procedure was demonstrated by analyzing surface and estuarine water.     

Determination of haloacetic acids in aqueous environments by solid-phase extraction followed by ion-pair liquid chromatography-electrospray ionization mass spectrometric detection.

Haloacetic acids (HAAs) were determined in different water samples by a new, fast and simple analysis method based on enrichment of 50-ml water samples at pH 1.8 by solid-phase extraction (SPE) followed by liquid chromatography (LC) separation and electrospray ionization mass spectrometric detection in the negative ionization mode. Deprotonated (M-H)-haloacetates and decarboxylated (M-COOH)- ions were detected. Different polymeric SPE sorbents were tested, and LiChrolut EN was found to be the best material for the extraction. Complete LC separation of all compounds could only be achieved by ion-pair chromatography using triethylamine as volatile ion-pairing reagent. The detection limits were in the low microg/l range. High microg/l concentration levels for the chlorinated and brominated haloacetates were found in drinking water from a drinking water treatment plant in Barcelona, and the corresponding tap water. In swimming pool water samples from Catalonia mg/l levels and in surface river water from Portugal microg/l values were detected. These results confirm other recent reports on the ubiquitous occurrence of HAAs in aqueous environments.     

Evaluation of Polyaniline as a Sorbent for SPE of a Variety of Polar Pesticides from Water Followed by CD-MEKC-DAD

A recently synthesized polyaniline (PANI) has been used and evaluated as a sorbent for solid-phase extraction of a variety of polar pesticides and some of their degradation products from water samples. Several classes of pesticides including phenoxy acids, triazines, ureas, oxime carbamates and carbamates were selected for this study. The determination of these pesticides was carried out using cyclodextrin modified micellar electrokinetic chromatography equipped with diode array detection. The recovery results using PANI were compared with those obtained by C₁₈, Isolute ENV+, Oasis HLB and LiChrolut EN. Effect of humic acid, as a major interference, on extraction recovery was also studied. The performance of the method was evaluated by analysis of tap and river water. The RSD of method was between 6 and 14% (n=3) and detection limits were in the range of 0.01–0.5 g L^–1 using 350-mL water samples.     

Continuous solid-phase extraction and gas chromatographic determination of organophosphorus pesticides in natural and drinking waters

A simple, rapid continuous-flow solid-phase extraction method with gas chromatographic detection for the determination of organophosphorus pesticides is proposed. The continuous system consists of an adsorbent column where pesticides are preconcentrated and subsequently eluted with ethyl acetate. Various sorbent materials were assayed of which RP-C18 was found to provide the best results, with a sorption efficiency close to 100%. A comparative study of the determination of pesticides in aqueous samples was conducted using gas chromatography with nitrogen-phosphorus (NPD) and flame ionization (FID) detection. The detection limits of the method for 10 ml of sample were between 50-130 ng/l and 4.5-1 1.7 microg/l with NPD and FID detection, respectively. The method was used to determine organophosphorus pesticides in river, pond, well and tap waters, all with good precision (2.9-4.3%) and recoveries ranging from 93.8 to 104.5%.     

Analysis of atrazine, terbutylazine and their N-dealkylated chloro and hydroxy metabolites by solid-phase extraction and gas chromatography-mass spectrometry and capillary electrophoresis-ultraviolet detection

Solid-phase extraction (SPE) with the styrene-divinylbenzene adsorbent LiChrolut EN was investigated for the extraction of the s-triazine herbicides atrazine and terbutylazine, their polar N-dealkylated degradation products deethylatrazine (DEA), deisopropylatrazine (DIA) and deethylterbutylazine (DET) and for the hydrophilic hydroxytriazine degradation products (HTDPs) hydroxyatrazine (HA), hydroxyterbutylazine (HT), deethylhydroxyatrazine (DEHA), deisopropylhydroxyatrazine (DIHA) and deethyldeisopropylhydroxyatrazine (ameline). The optimum pH value for the extraction of the HTDPs from fortified tap water at 2 micrograms/l is 3.0. Recovery values with 200 mg LiChrolut EN are > 80% for HA, HT, DEHA and 30% for DIHA from 200 ml spiked tap and river water. Atrazine, terbutylazine, DEA, DIA and DET are quantitatively extracted by LiChrolut EN. The chlorotriazines are analyzed by GC-MS and the HTDPs by capillary zone electrophoresis (CZE) and micellar electrokinetic capillary chromatography (MECC) with an acetate buffer at pH 4.6 or a sodium borate-sodium dodecyl sulfate buffer at pH 9.3. The combined method of SPE enrichment and CE analysis allows the determination of HTDPs in the low microgram/l range.     

Pyrrole-based conductive polymer as the solid-phase extraction medium for the preconcentration of environmental pollutants in water samples followed by gas chromatography with flame ionization and mass spectrometry detection

A pyrrole-based polymer was synthesized and applied as a new sorbent for solid-phase extraction (SPE) of some environmental pollutants from water samples. Polypyrrole (PPy) was synthesized by chemical oxidation of the monomer in nonaqueous solution. SPE of selected phenols, pesticides, and polyaromatic hydrocarbons (PAHs) from aqueous samples were performed using 200 mg PPy. The determination was subsequently carried out by gas chromatography-flame ionization detection (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The polymer showed much higher recoveries for aromatic compounds than aliphatics. Preconcentration of sample volumes up 11 led to acceptable recoveries for aromatic and other tested polar compounds. The R.S.D. for a river water sample spiked with phenols, pesticides and PAHs at sub-ppb level was lower than 10% (n = 3) and limits of detection for these compounds were between 15 and 120 ng l(-1).     

Monitoring of antifouling agents in water samples by on-line solid-phase extraction-liquid chromatography-atmospheric pressure chemical ionization mass spectrometry

An automatic method for determining diuron, irgarol 1051, folpet and dichlofluanid in seawater samples have been developed. This method is based on the on-line coupling of solid-phase extraction (SPE) with a highly crosslinked polymeric sorbent, LiChrolut EN, to liquid chromatography followed by atmospheric pressure chemical ionization (APCI) and mass spectrometry. The operational parameters affecting the APCI interface have been studied in both positive and negative ionization modes. The use of LiChrolut EN in the SPE produced recoveries of over 85% for all the compounds when 100 ml of seawater sample was preconcentrated. Calibration was carried out in both ionization modes and in full-scan and selected-ion monitoring (SIM). The method allowed all the analytes to be detected at 5 ng l(-1) in SIM acquisition mode except folpet, which, because of its low response, could only be detected at 250 ng l(-1). The method was used to analyse water samples taken from five different marina and fishing ports along the coast of Tarragona, Catalonia (Spain), over a 5-month period. Diuron and irgarol 1051 were detected and quantified in most samples at concentration levels ranging from 27 to 420 ng l(-1) for diuron and from 15 to 511 ng l(-1) for irgarol 1051.     

Determination of endogenous and exogenous estrogens in effluents from sewage treatment plants at the ng/L-level

An analytical method for the determination of the major endogenous and exogenous estrogenic steriods in effluent water samples of sewage treatment plants (STPs) with a LOQ down to 1 ng/L and below has been developed. The exogenous estrogen 17alpha-ethynylestradiol, frequently used as estrogenic component in oral contraceptives, and the endogenous estrogen 17beta-estradiol show the highest estrogenic potential, therefore they were part of our target compounds. In addition, the content of the synthetic gestagen levonorgestrel, also often administered in oral contraceptives, was determined. A solid-phase extraction system for high volume sampling of water up to 25 L was implemented. Two types of adsorbent, Amberlite XAD 2 and a mixture of LiChrolut EN/Bondesil C-18, respectively, were tested for their extraction efficiency of these polar analytes. Recovery rates with LiChrolut EN/Bondesil C-18 ranged up to 94%, whereas sampling on XAD 2 led only to poor recoveries below 40%. After a liquid chromatographic clean-up step on silicagel the steroids were converted into their trimethylsilyl-ethers by the reaction with MSTFA/TMSI (N-methyl-N-trimethylsilyl-2,2,2-trifluoroacetamide, trimethylsilyliodide) and were then determined by HRGC/MS in the selected ion mode. A limit of quantification over the whole procedure of at least 1 ng/L was reached for all analytes. In several effluent samples the input of estrogens by the STP of the cities Ulm and New Ulm into the river Danube was characterised. The concentrations commonly found ranged from 1 ng/L up to 13 ng/L, depending on the respective steroid.     

Hydrophilic hypercrosslinked polymeric sorbents for the solid-phase extraction of polar contaminants from water

Three new hypercrosslinked polymers with hydrophilic character arising from hydroxyl moieties in their skeletons have been prepared in microsphere format and applied to the off-line solid-phase extraction (SPE) of polar compounds from water samples. For sample volumes of 1000 ml, the recoveries of various polar pesticides, such as oxamyl, methomyl, selected phenolic compounds, as well as some pharmaceuticals, were close to 90%. The HXLPP-polar polymer with the best performance characteristics was applied to real samples. Its performance was also compared to commercially available sorbents, such as LiChrolut EN (hydrophobic, hypercrosslinked), Oasis HLB (hydrophilic, macroporous) and Isolute ENV+ (hydrophilic, hypercrosslinked); the new sorbent out-performed the commercially available sorbents. The polymer was applied successfully in off-line SPE of river water samples followed by liquid chromatography and ultraviolet detection, providing a good linear range and detection limits of 0.2 μg l⁻¹ for the majority of the compounds, with the exception of oxamyl, methomyl, guaiacol and salicylic acid where the detection limit was 0.5 μg l⁻¹.     

Comparison of a non-aqueous capillary electrophoresis method with high performance liquid chromatography for the determination of herbicides and metabolites in water samples

A method of capillary electrophoresis (CE) for the determination of triazine herbicides and some of their main metabolites in water samples has been developed. The proposed CE method includes an off-line solid-phase extraction (SPE) procedure with LiChrolut EN sorbent coupled to a non-aqueous capillary electrophoresis (NACE) separation with UV detection. The target compounds were the chloro-s-triazines simazine, atrazine, propazine; the methyltio-s-triazines ametryn and prometryn and three main derivatives from the atrazine degradation products; namely, deethylatrazine, deethylhydroxyatrazine and deisopropylhydroxyatrazine. The analytical characteristics of the CE method are reported. The repeatability of the method was studied considering the different steps of the method separately in order to determine the contributions of each step to the total variability of the method. The NACE-UV results are compared with those obtained with a high performance liquid chromatography with UV detection (HPLC-UV) method. The same off-line SPE procedure was applied to both techniques. The results obtained show that both methods afford the same results in the analysis of surface and drinking water samples, with a level of significance regarding the F- and t-tests greater than 0.05 in all the cases. The detection limits in surface water samples were in the 0.04-0.32 microg l(-1) and 0.11-1.2 microg l(-1) ranges for the NACE-UV and HPLC-UV methods, respectively. The recoveries (spiked/found) were significantly 100% in all cases.     

Determination of endogenous and exogenous estrogens in effluents from sewage treatment plants at the ng/L-level

An analytical method for the determination of the major endogenous and exogenous estrogenic steriods in effluent water samples of sewage treatment plants (STPs) with a LOQ down to 1 ng/L and below has been developed. The exogenous estrogen 17α-ethynylestradiol, frequently used as estrogenic component in oral contraceptives, and the endogenous estrogen 17β-estradiol show the highest estrogenic potential, therefore they were part of our target compounds. In addition, the content of the synthetic gestagen levonorgestrel, also often administered in oral contraceptives, was determined. A solid-phase extraction system for high volume sampling of water up to 25 L was implemented. Two types of adsorbent, Amberlite XAD 2 and a mixture of LiChrolut EN/Bondesil C-18, respectively, were tested for their extraction efficiency of these polar analytes. Recovery rates with LiChrolut EN/¶Bondesil C-18 ranged up to 94 %, whereas sampling on XAD 2 led only to poor recoveries below 40 %. After a liquid chromatographic clean-up step on silicagel the steroids were converted into their trimethylsilyl-ethers by the reaction with MSTFA/TMSI (N-methyl-N-trimethylsilyl-2,2,2-trifluoroacetamide, trimethylsilyliodide) and were then determined by HRGC/MS in the selected ion mode. A limit of quantification over the whole procedure of at least 1 ng/L was reached for all analytes. In several effluent samples the input of estrogens by the STP of the cities Ulm and New Ulm into the river Danube was characterised. The concentrations commonly found ranged from 1 ng/L up to 13 ng/L, depending on the respective steroid.     

Liquid chromatographic determination of nine N-methylcarbamates in drinking water

A multi-residue method for the simultaneous extraction from drinking water using solid-phase extraction on LiChrolut EN [poly(styrene-divinylbenzene), PSDVB] and determination of nine N-methylcarbamate pesticides (NMCs) (aldicarb, its metabolites i.e. aldicarb sulfone and aldicarb sulfoxide and carbaryl, carbofuran, dioxacarb, ethiofencarb, methomyl and propoxur) using reversed-phase liquid chromatography was studied. A 1000-fold pre-concentration was achieved and the method was used for determination of the nine pesticides in water, with limits of detection in the range 3-15 ng L(-1). For all compounds the recoveries determined at the 0.1 and 1 microg L(-1) level generally ranged from 85 to 104% with relative standard deviations (RSD) of 1.4-8.8%.     

Preparation and evaluation of a molecularly imprinted sol-gel material for on-line solid-phase extraction coupled with high performance liquid chromatography for the determination of trace pentachlorophenol in water samples

A highly selective imprinted amino-functionalized silica gel sorbent was prepared by combining a surface molecular imprinting technique with a sol-gel process for on-line solid-phase extraction-HPLC determination of trace pentachlorophenol (PCP) in water samples. The PCP-imprinted amino-functionalized silica sorbent was characterized by FT-IR, SEM, nitrogen adsorption and the static adsorption experiments. The imprinted functionalized silica gel sorbent exhibited high selectivity and offered a fast kinetics for the adsorption and desorption of PCP. The prepared sorbent was shown to be promising for on-line solid-phase extraction for HPLC determination of trace levels of PCP in environmental samples. With a sample loading flow rate of 5 ml min(-1) for 2 min, an enhancement factor of 670 and a detection limit (S/N = 3) of 6 ng l(-1) were achieved at a sample throughput of five samples h(-1). The precision (RSD) for nine replicate on-line sorbent extractions of 10 microgl(-1) PCP was 3.8%. The sorbent also offered good linearity (r = 0.9997) for on-line solid-phase extraction of trace levels of PCP. The method was applied to the determination of PCP in local lake water, river water and wastewater samples.     

Comparison of several sorbents for continuous in situ derivatization and preconcentration of low-molecular mass aldehydes prior to liquid chromatography–tandem mass spectrometric determination in water samples

A comparative study of six SPE conventional and non-conventional sorbent materials (silica RP-C₁₈, LiChrolut EN, Amberlite XAD-2, C₆₀ fullerene, multiwall carbon nanotubes and graphitized carbon black) was carried out for the in situ derivatization/preconcentration of eight aldehydes with 2,4-dinitrophenylhydrazine. Although two of the sorbents, LiChrolut EN and RP-C₁₈, turned out to be the most suitable for ultratrace analysis of the aldehydes, LiChrolut EN showed higher capacity for 2,4-dinitrophenylhydrazine trapping (higher efficiency for the in situ derivatization reaction) and superior performance in terms of sensitivity (likely a result of its increased sample breakthrough volume). The LiChrolut EN-based method combined with LC–MS/MS allowed the determination of aldehydes over the linear range of 0.02–15 μg l⁻¹, with limits of detection at 6–24 ng l⁻¹ and precision of 3.2–7.2%. The method was applied to determine low-molecular mass aldehydes in water samples. These results indicate that the method proposed is a straightforward and sensitive tool for the determination of these aldehydes in water samples providing better results than those LC–MS/MS reported alternatives in terms of the limit of detection, sample requirements for analysis and cost.     

Tandem Solid-Phase Extraction Columns for Simultaneous Aroma Extraction and Fractionation of Wuliangye and Other Baijiu

Wuliangye baijiu is one of the most famous baijiu in China, with a rich, harmonic aroma profile highly appreciated by consumers. Thousands of volatiles have been identified for the unique aroma profile. Among them, fatty acid esters have been identified as the main contributors to the aroma profile. In addition, many non-ester minor compounds, many of which are more polar than the esters, have been identified to contribute to the characteristic aroma unique to Wuliangye baijiu. The analysis of these minor compounds has been challenging due to the dominance of esters in the sample. Thus, it is desirable to fractionate the aroma extract into subgroups based on functional group or polarity to simplify the analysis. This study attempts a new approach to achieve simultaneous volatile extraction and fractionation using tandem LiChrolut EN and silica gel solid-phase extraction (SPE) columns. A baijiu sample (10 mL, diluted in 40 mL of water) was first passed through the LiChrolut EN (1.0 g) column. The loaded LiChrolut EN column was then dried with air and coupled with a silica gel (5.0 g) SPE column with anhydrous Na₂SO₄ (10.0 g) in between. The volatile compounds were eluted from the LiChrolut EN column and simultaneously fractionated on the silica gel column based on polarity. The simultaneous extraction and fractionation technique enabled the fractionations of all fatty acid esters into less polar fractions. Fatty acids, alcohols, pyrazines, furans, phenols, hydroxy esters, and other polar compounds were collected in more polar fractions. This technique was used to study the volatile compounds in Wuliangye, Moutai, and Fengjiu baijiu. In addition to fatty acid esters, many minor polar compounds, including 2,6-dimethylpyrazine, 2-ethyl-6-methylpyrazine, 2-ethyl-3,5-dimethylpyrazine, p-cresol, and 2-acetylpyrrole, were unequivocally identified in the samples. The procedure is fast and straightforward, with low solvent consumption.