Comprehensive two-dimensional gas chromatography/mass spectrometric analysis of pepper volatiles

The headspace compositions of 13 pepper and peppercorn samples of different species, colloquially also referred to as pepper, were analyzed, and more than 300 compounds were tentatively characterized by means of comprehensive two-dimensional gas chromatography in tandem with flame ionization detection, quadrupole mass spectrometric detection and time-of-flight mass spectrometric detection (GC x GC-FID, GC x GC/qMS and GC x GC/TOFMS, respectively). The analysis of volatile organic compounds (VOCs) was performed after solid-phase microextraction (SPME) using a 75-microm PDMS/DVB fibre. Fingerprint comparison between the three techniques permitted peaks to be assigned in the GC x GC-FID experiment based on the analogous MS analysis, taking into account retention shifts arising from method variations. When using GC x GC/TOFMS, about five times more peaks were identified than in GC x GC/qMS. Retention indices for all peaks were calculated in the bi-dimensional column set comprising of a 5% phenyl polysilphenylene-siloxane primary column and a polyethylene glycol second column. The spectra obtained by both mass detection techniques (qMS and TOFMS) give very similar results when spectral library searching was performed. The majority of the identified compounds eluted as pure components as a result of high-resolution GC x GC separations, which significantly reduces co-elution, and therefore increases the likelihood that pure spectra can be obtained. The differences between TOFMS and qMS (in fast scanning mode) spectra were generally small. Whilst spectral quality and relative ion ratios across a narrow peak (e.g. w(b) approximately 100-150 ms) do vary more for the fast peaks obtained in GC x GC/qMS operation, than with TOFMS, in general adequate spectral matching with the library can be achieved.     

A Comparison of One-Dimensional and Comprehensive Two-Dimensional Gas Chromatography for Decomposition Odour Profiling Using Inter-Year Replicate Field Trials

Decomposition odour analysis involves the chemical profiling of volatile organic compounds produced by decomposing remains. This is important for areas of forensic science that rely on the detection of decomposition odour such as insect attraction to carrion, positive alerts of cadaver dogs to decomposing remains, and the development of field instrumentation for search and recovery procedures. Traditionally decomposition odour analysis has been performed using gas chromatography–quadrupole mass spectrometry (GC–qMS); however, the use of comprehensive two-dimensional gas chromatography–time-of-flight mass spectrometry (GC×GC–TOFMS) is rapidly becoming more prevalent. The objective of this study was to compare GC–qMS and GC×GC–TOFMS for decomposition odour profiling based on inter-year replicate field studies using decomposing porcine remains. The increased peak capacity, sensitivity and selectivity afforded by GC×GC–TOFMS allowed peak co-elutions, chromatographic artefacts, and dynamic range to be more easily addressed and managed. Furthermore, the software associated with GC×GC–TOFMS provided several additional benefits including improved peak alignment between samples and increased consistency of reported results, overall allowing for additional statistical tests to be applied following data processing. Future GC–qMS results could be improved by implementing some of these software-associated procedures, potentially reducing the magnitude of variation observed between GC–qMS and GC×GC–TOFMS studies. One-dimensional GC analysis may also benefit substantially from coupling with TOFMS detection to provide an indirect increase in peak capacity using deconvolution. However, the wealth of information gained by using GC×GC–TOFMS in decomposition odour profiling is undoubtedly an asset in this field of research.

     

The combination of gas chromatography-olfactometry and multidimensional gas chromatography for the characterisation of essential oils

A research area of great interest to the flavour industry is the analysis of odour active compounds in essential oils. In this paper, a methodology is presented for the identification of character-impact odorants in essential oil samples using (a) gas chromatography-olfactometry (GC-O); (b) comprehensive two-dimensional gas chromatography (GC x GC) combined to time-of-flight mass spectrometry (TOFMS) and (c) heart-cut multidimensional gas chromatography-olfactometry (MDGC-O). The specific advantages and limitations of each technique are discussed. The advantage of combining these techniques in a strategy to identify character-impact odorants is demonstrated using examples from coriander leaf (Coriandrum sativum) and hop (Humulus lupulus) essential oils. In particular, resolution of co-eluting regions of compounds and evaluation of their individual odour activity is discussed. In coriander leaf, only E-2-dodecenal was found to contribute to a co-eluting odour region, E-2-dodecen-1-ol and 1-dodecanol being present below detection threshold. Using MDGC on a hop essential oil sample, eight significant peaks were resolved from an 18 s heart-cut where a potent odorant was perceived during GC-O.     

全二维气相色谱/飞行时间质谱用于柴油组成的研究

将全二维气相色谱法(GC×GC)用于柴油馏分的组成分布研究,建立了两种GC×GC方法,一种用于柴油组成的详细表征,另一种用于柴油族组成的快速分离和定量,两种方法均不需要样品预处理。用前一种方法对柴油馏分中的烃类化合物、主要的含硫化合物与含氮化合物组成进行了研究;对催化裂解柴油中的27种含氮化合物和42种含硫化合物进行了定性;用后一种方法在70 min内即可完成柴油馏分族组成的定量分析,应用所建立的方法测定了4个不同来源的柴油馏分中非芳烃、一环芳烃、二环芳烃、三环芳烃的含量,定量结果与ASTM D2425法     

Characterization of cigarette smoke condensates by comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry (GC x GC/TOFMS). Part 2: basic fraction

Cigarette smoke condensate is a complex chemical matrix. Analysis of nitrogen-containing compounds present therein is very difficult because of the limitation of the peak capacity of conventional one-dimensional chromatography. Extensive and laborious sample preparation is frequently required or selective detectors are frequently used. In this study, the basic fraction of mainstream cigarette smoke condensate has been investigated by using comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry (GC x GC/TOFMS). Auto data processing by TOFMS software combined with manual identification was used to assign the components. 377 nitrogen-containing compounds, including 155 pyridine derivatives, 104 quinoline/isoquinoine derivatives, and 56 pyrazine derivatives were tentatively identified. By selecting appropriate unique masses and in the light of the component positions in the structured chromatogram, alkyl-substituted pyridines, pyrazines, and quinolines/isoquinolines were separately shown and further validated. The peaks of eight individual positional isomers of two-carbon-substituted pyridines and thirteen positional isomers of methyl-substituted quinolines/isoquinolines were further confirmed, based on linear incremental retention behavior in combination with TOFMS and the structured chromatogram of GC x GC.     

Application of headspace solid-phase microextraction (HS-SPME) and comprehensive two-dimensional gas chromatography (GC x GC) for the chemical profiling of volatile oils in complex herbal mixtures

The coupling of headspace solid-phase microextraction (HS-SPME) with comprehensive two-dimensional gas chromatography (GC x GC) was shown to be a powerful technique for the rapid sampling and analysis of volatile oils in complex herbal materials. When compared to one-dimensional (1-D) GC, the improved analytical capabilities of GC x GC in terms of increased detection sensitivity and separation power were demonstrated by using HS-SPME/GC x GC for the chemical profiling (fingerprinting) of essential/volatile oils contained in herbal materials of increasing analytical complexity. More than 20 marker compounds belonging to Panax quinquefolius (American ginseng) can be observed within the 2-D contour plots of ginseng itself, a mixture of ginseng and another important herb (P. quinquefolius/Radix angelicae sinensis), as well as a mixture of ginseng and three other herbs (P. quinquefolius /R. angelicae sinensis/R. astragali/R. rehmanniae preparata). Such analytical capabilities should be important towards the authentication and quality control of herbal products, which are receiving increasing attention as alternative medicines worldwide. In particular, the presence of Panax in the herb formulation could be readily identified through its specific peak pattern in the 2-D GC x GC plot.     

Comparison of comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry and gas chromatography-mass spectrometry for the analysis of tobacco essential oils

A sample of tobacco essential oil was analyzed using gas chromatography-mass spectrometry (GC/MS) and comprehensive two-dimensional gas chromatography coupled to a time-of-flight mass spectrometry (GC × GC/TOFMS), respectively. In the GC/MS analysis, serially coupled columns were used. By comparing the GC/MS results with GC × GC/TOFMS results, many more components in the essential oil could be found within the two-dimensional separation space of GC × GC. The quantitative determination of components in the essential oil was performed by GC × GC with flame ionization detection (FID), using a method of multiple internal standards calibration.     

Investigation of sulphur compounds in coal tar using monodimensional and comprehensive two-dimensional gas chromatography

Coal is a non renewable fossil fuel, used mainly as a source of electrical energy and in the production of coke. It is subjected to thermal treatment, pyrolysis, which produces coke as a main product, in addition to a condensed liquid by-product, called tar. Tar is a complex mixture of organic compounds which contains different chemical classes, presenting aromatic and sulphur heterocyclic compounds. In general, identification of these compounds requires steps of isolation and fractionation, mainly due to co-elution of these compounds with polyaromatic hydrocarbons (PAH). The objective of this work is to characterize the sulphur compounds present in the coal tar obtained via pyrolysis, using comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). Coal samples from the State of Paraná, Brazil were subjected to laboratorial scale pyrolysis. Several experimental conditions were tested, such as sample weight (5, 10 and 15g), heating ramp (10, 25 and 100°C/min) and final temperature (500, 700 and 900°C). Samples were analyzed by one dimensional gas chromatography (1D-GC) coupled to a quadrupole mass spectrometry detector (GC/qMS) and two-dimensional gas chromatography with time-of-flight mass spectrometry detector (GC×GC/TOFMS). The higher amount of sulphur compounds was obtained at a final temperature of 700°C and a heating ramp of 100°C/min. The main classes observed in the color plot were thiophenes, benzothiophenes and alkylated dibenzothiophenes. GC×GC/TOFMS allowed the identification of the greater number of compounds and the separation of several sulphur compounds from one another. Moreover, separation of sulphur compounds from polyaromatic hydrocarbons and phenols was achieved, which was not possible by 1D-GC. Comparing GC×GC/TOFMS and 1D-GC (SIM mode) also showed that 1D-GC, one of the most employed quantification tools for sulphur compounds, can be misleading for detection, identification and quantification, as the number of isomers of sulphur compounds found was greater than theoretically possible.     

Comprehensive two-dimensional gas chromatography with flame ionization and time-of-flight mass spectrometry detection: qualitative and quantitative analysis of West Australian sandalwood oil

The use of gas chromatography (GC)-mass spectrometry (MS), GC-time-of-flight MS (TOFMS), comprehensive two-dimensional GC (GCxGC)-flame ionization detection (FID), and GCxGC-TOFMS is discussed for the characterization of the eight important representative components, including Z-alpha-santalol, epi-alpha-bisabolol, Z-alpha-trans-bergamotol, epi-beta-santalol, Z-beta-santalol, E,E-farnesol, Z-nuciferol, and Z-lanceol, in the oil of west Australian sandalwood (Santalum spicatum). Single-column GC-MS lacks the resolving power to separate all of the listed components as pure peaks and allow precise analytical measurement of individual component abundances. With enhanced peak resolution capabilities in GCxGC, these components are sufficiently well resolved to be quantitated using flame ionization detection, following initial characterization of components by using GCxGC-TOFMS.     

Recent advances in mass spectrometric measurement of dioxins

Past years, many efforts have been dedicated to the development of alternative analytical methods for the measurement of dioxins in various types of matrices. Polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and polychlorinated biphenyls (PCBs) are compounds that are present in samples at part-per-billion (ppb) or part-per-trillion (ppt) level. Their measurement requires the use of very sensitive analytical methods. Gas chromatography (GC) coupled to quadrupole ion storage mass spectrometry (QISTMS), fast GC (FGC) coupled to time-of-flight mass spectrometry (TOFMS) and comprehensive two-dimensional gas chromatography (GC x GC) coupled to TOFMS are the more promising tools challenging the reference GC high resolution mass spectrometry (HRMS) based on sector instruments. We report herein some of the advances we achieved in the past years in our laboratory on the development of alternative measurement methods for those compounds.     

Characterization of military fog oil by comprehensive two-dimensional gas chromatography

The most commonly used military fog oil is characterized by comprehensive two-dimensional gas chromatography (GC×GC) coupled to either Flame Ionization Detection (FID) or Time-of-Flight Mass Spectrometric Detection (TOFMS) to advance the knowledge regarding the complete chemical makeup of this complex matrix. Two different GC×GC column sets were investigated, one employing a non-polar column combined with a shape selective column and the other an inverse column set (medium-polar/non-polar). The inverse set maximizes the use of the two-dimensional separation space and segregates aliphatic from aromatic fractions. The shape selective column best separates individual polycyclic aromatic hydrocarbons (PAHs) from the bulk oil. The results reveal that fog oil (FO) is composed mainly of aliphatic compounds ranging from C₁₀ to C₃₀, where naphthenes comprise the major fraction. Although many different species of aromatics are present, they constitute only a minor fraction in this oil, and no conjugated PAHs are found. The composition of chemically similar aliphatic constituents limits the analytical power of silica gel fractionation and GC–MS analysis to characterize FO. Among the aliphatic compounds identified are alkanes, cyclohexanes, hexahydroindanes, decalins, adamantanes, and bicyclohexane. The aromatic fraction is composed of alkylbenzene compounds, indanes, tetrahydronaphthalenes, partially hydrogenated PAHs, biphenyls, dibenzofurans and dibenzothiophenes. This work represents the best characterization of military fog oil to date. As the characterization process shows, information on such complex samples can only be parsed using a combination of sample preprocessing steps, multiple detection schemes, and an intelligent selection of column chemistries.     

Quantification in comprehensive two-dimensional gas chromatography and a model of quantification based on selected summed modulated peaks

In common with all gas chromatography (GC) methods, comprehensive two-dimensional gas chromatography (GC x GC) has the potential to provide both qualitative and quantitative analysis. There are fundamental differences in the way one-dimensional (1D-GC) and GC x GC results are interpreted for these parameters. Since 1D-GC produces a single measured peak in the chromatogram, there is a single retention time, and associated with this a single peak response (either area or height). Peak area and height are related by peak width. GC x GC produces a series of modulated peaks at the detector. Thus, the peak metrics of retention, area and height for one component are now not simple single values for one peak, but rather are derived from the multiple peak distribution generated by the modulation process. The peak retention is interpreted in terms of two-dimensional coordinates in a retention plane. In this study, a brief background review to quantification in GC x GC is provided. Previous reviews cover aspects of quantitative GC x GC studies up to the year 2005, including different approaches to quantification, and reports of quantitative analysis with different detectors, for different compounds classes, and in different matrices. Other studies have developed chemometric approaches based on multivariate analysis to provide quantitative reporting of individual compounds. The coverage of the earlier reviews has been updated to include material that has been presented since 2005 and includes considerations of valve-based modulation. Recently the modulation ratio (M(R)) concept was proposed and intended to clarify the meaning of modulation number (n(M)) in GC x GC, which was shown to be a rather poorly defined parameter. Based on the prior studies that introduced this concept, the role of quantitative analysis is investigated here through calculation of the peak areas and peak area ratios of selected series of modulated peaks in GC x GC. The application of isotopically labelled reference compounds for polycyclic aromatic hydrocarbon (PAH) analysis is used here to develop the quantitative metric approach. It is shown that by selecting the two or three major modulated peaks for solutes and internal standards, comparing the response ratio with the sum of all modulated peaks and also with the reference non-modulated result, quantification is statistically equivalent. Thus, adequate quantitative analysis and calibration can be accomplished by using selected major modulated peaks for each compound. This may simplify quantitative interpretation of GC x GC data.     

Quantification of polychlorinated dibenzo-p-dioxins and dibenzofurans by direct injection of sample extract into the comprehensive multidimensional gas chromatograph/high-resolution time-of-flight mass spectrometer

Polychlorinated dibenzo-p-dioxins and dibenzofurans in crude extracts of fly ash and flue gas from municipal waste incinerators were quantified using a comprehensive multidimensional gas chromatograph (GC x GC) coupled to a high-resolution time-of-flight mass spectrometer (HR-TOFMS). For identification and quantification, we developed our own program to prepare 3D chromatograms of selected mass numbers from the data of the GC x GC/HR-TOFMS. Isolation of all congeners with a TCDD toxic equivalency factor from the other isomers by only one injection was confirmed. The instrumental detection limit of TCDD on the GC x GC/HR-TOFMS was 0.9 pg by the relative calibration method. Quantification of these substances in the crude extracts was achieved by direct injection to the GC x GC/HR-TOFMS. The results agree with the values obtained using a generic gas chromatography/high-resolution mass spectrometry (GC/HRMS) system. It was confirmed that measurement by high-resolution TOFMS and GC x GC effectively reduces interference from other chemicals.     

Universal and discriminative detection using a miniaturized pulsed discharge detector in comprehensive two-dimensional GC

A miniaturized pulsed discharge detector (Mini-PDD) has been successfully demonstrated for comprehensive 2-D GC (GC x GC) analysis of pyrolysis gasoline and the pyrolysis GC x GC analysis of a polyethylene copolymer. The detector cell volume of the Mini-PDD is reduced to 25% of the Valco plug-in PDD D-3. An n-C11 peak width at base is 96 ms for the Mini-PDD, about 23% larger than a peak width of 78 ms detected by a flame ionization detector (FID). The Mini-PDD has sufficient response time for most GC x GC applications. When Mini-PDD is operated in helium photoionization mode (Mini He-PDD), it is a universal detector for both inorganic and organic compounds. This is especially useful when detection of water is needed in GC x GC applications. When krypton is doped in the helium discharge gas (Mini Kr-PDD), it can suppress signals of compounds having higher ionization potentials and enhance relative signal intensities of aromatic compounds. The determination of aliphatic to aromatic hydrocarbon ratios is essential to the operation of petroleum crackers. Comparison of the signal from two modes of the Mini-PDD is a simple and fast way to verify the location of aromatics in comprehensive 2-D gas chromatograms.     

Quantification of naphthalenes in jet fuel with GC x GC/Tri-PLS and windowed rank minimization retention time alignment

Comprehensive, two-dimensional gas chromatography (GC x GC) is used in conjunction with trilinear partial least squares (Tri-PLS) to quantify the percent weight of naphthalenes (two-ring aromatic compounds) in jet fuel samples. The increased peak capacity and selectivity of GC x GC makes the technique attractive for the rapid, and possibly less tedious analysis of jet fuel. The analysis of complex mixtures by GC x GC is further enhanced through the use of chemometric techniques, including those designed for use on 2-D data such as Tri-PLS. Unfortunately, retention time variation, unless corrected, can be an impediment to chemometric analysis. Previous work has demonstrated that the effects of retention time variation can be mitigated in sub-regions of GC x GC chromatograms through the application of an objective retention time alignment algorithm based on rank minimization. Building upon this previous work, it is demonstrated here that the effects of retention time variation can be mitigated throughout an entire GC x GC chromatogram with an objective retention time alignment algorithm based on windowed rank minimization alignment. A significant decrease in calibration error is observed when the algorithm is applied to chromatograms prior to construction of Tri-PLS models. Fourteen jet fuel samples with known weight percentages of naphthalenes (ASTM D1840) were obtained. Each sample was subjected to five replicate five-minute GC x GC separations over a period of two days. A subset of nine samples spanning the range of weight percentages of naphthalenes was chosen as a calibration set and Tri-PLS calibration models were subsequently developed in order to predict the naphthalene content of the samples from the GC x GC chromatograms of the remaining five samples. Calibration models constructed from GC x GC chromatograms that were retention time corrected are shown to exhibit a root mean square error of prediction of roughly half that of calibration models constructed from uncorrected chromatograms. The error of prediction is lowered further to a value that nearly matches the uncertainty in the standard percent weight values (ca. 1% of the median percent volume value) when the aligned chromatograms are truncated to include only regions of the chromatogram populated by naphthalenes and compounds of similar polarity and boiling point.     

Pressure‐Tunable Dual‐Column Ensembles for High‐Speed GC and GC/MS

A series‐coupled ensemble of two capillary GC columns of different selectivity with an adjustable pressure at the column junction point is used to obtain tunable selectivity for high‐speed GC and GC/TOFMS. An electronic pressure controller with a 0.1‐psi step size is used to obtain numerous computer‐selected unique selectivities. System configurations for conventional, atmospheric‐pressure outlet operation with flame ionization detection and for vacuum‐outlet operation with photoionization detection are described for GC‐only experiments. Polydimethylsiloxane is used as the non‐polar column and polyethylene glycol (atmospheric outlet) or triflouropropylpolysiloxane (vacuum outlet) is used as the polar column. For GC/TOFMS experiments, 5% phenyl polydimethylsiloxane was used as the non‐polar column, and polyethylene glycol was used as the polar column. The time‐of‐flight mass spectrometer can acquire up to 500 complete mass spectra per second. Since spectral continuity is achieved across the entire chromatographic peak profile, severely overlapping peaks can be spectrally deconvoluted for high‐speed characterization of completely unknown mixtures. For mixture components with significantly different fragmentation patterns, spectral deconvolution can be achieved for chromatographic peak separations of as little as 6.0 ms. This can result is very large peak capacity for time compressed (not completely resolved) chromatograms. The use of columns with tunable selectivity allows for precise peak‐position control, which can result in more efficient utilization of available peak capacity and thus further time compression of chromatograms. The limits of tunability and deconvolution are tested for near co‐elutions of different classes of hydrocarbon compounds as well as for more multi‐functional mixtures.     

Identification of volatiles from pineapple (Ananas comosus L.) pulp by comprehensive two-dimensional gas chromatography and gas chromatography/mass spectrometry

Combining qualitative data from the chromatographic structure of 2-D gas chromatography with flame ionization detection (GC×GC-FID) and that from gas chromatography-mass spectrometry (GC/MS) should result in a more accurate assignment of the peak identities than the simple analysis by GC/MS, where coelution of analytes is unavoidable in highly complex samples (rendering spectra unsuitable for qualitative purposes) or for compounds in very low concentrations. Using data from GC×GC-FID combined with GC/MS can reveal coelutions that were not detected by mass spectra deconvolution software. In addition, some compounds can be identified according to the structure of the GC×GC-FID chromatogram. In this article, the volatile fractions of fresh and dehydrated pineapple pulp were evaluated. The extraction of the volatiles was performed by dynamic headspace extraction coupled to solid-phase microextraction (DHS-SPME), a technique appropriate for slurries or solid matrices. Extracted analytes were then analyzed by GC×GC-FID and GC/MS. The results obtained using both techniques were combined to improve compound identifications.     

Analysis of methoxypyrazines in wine using headspace solid phase microextraction with isotope dilution and comprehensive two-dimensional gas chromatography

This study reports an optimized headspace-solid phase microextraction (HS-SPME) method for the determination of methoxypyrazines in wine. Analysis was performed by using comprehensive two-dimensional gas chromatography with novel detection capabilities, including nitrogen phosphorus detection (GC x GC-NPD) and time-of-flight mass spectrometry (GC x GC-TOFMS). In the latter, stable isotope dilution was performed for the quantitation of 2-methoxy-3-(2-methylpropyl) pyrazine (IBMP), using labelled 2-(2H3)methoxy-3-(2-methylpropyl)pyrazine (d3-IBMP) as the internal standard, and resolution of the two analogues was facilitated using the deconvolution capabilities of the TOFMS. This research represents the first report of HS-SPME with isotope dilution and GC x GC-TOFMS (GC x GC-IDTOFMS). Analysis by GC x GC-NPD enabled detection limits of 0.5 ng/L for the quantitation of IBMP, which was superior to that obtained using GC x GC-IDTOFMS (1.95 ng/L). Nevertheless, both methods were adequately sensitive for real wine analysis, yielding highly comparable IBMP concentrations of 26.1 and 27.8 ng/L, respectively, from a Sauvignon blanc wine. The complexity of the real wine headspace was simplified as a result of selective detection using GC x GC-NPD and, in the case of GC x GC-IDTOFMS, the use of extracted ion chromatograms (EICs).     

Identification of organic sulfur compounds in coal bitumen obtained by different extraction techniques using comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometric detection

The determination of organic sulfur compounds (OSC) in coal is of great interest. Technically and operationally these compounds are not easily removed and promote corrosion of equipment. Environmentally, the burning of sulfur compounds leads to the emission of SO _x gases, which are major contributors to acid rain. Health-wise, it is well known that these compounds have mutagenic and carcinogenic properties. Bitumen can be extracted from coal by different techniques, and use of gas chromatography coupled to mass spectrometric detection enables identification of compounds present in coal extracts. The OSC from three different bitumens were tentatively identified by use of three different extraction techniques: accelerated solvent extraction (ASE), ultrasonic extraction (UE), and supercritical-fluid extraction (SFE). Results obtained from one-dimensional gas chromatography (1D GC) coupled to quadrupole mass spectrometric detection (GC–qMS) and from two-dimensional gas chromatography with time-of-flight mass spectrometric detection (GC × GC–TOFMS) were compared. By use of 2D GC, a greater number of OSC were found in ASE bitumen than in SFE and UE bitumens. No OSC were identified with 1D GC–qMS, although some benzothiophenes and dibenzothiophenes were detected by use of EIM and SIM modes. GC × GC–TOFMS applied to investigation of OSC in bitumens resulted in analytical improvement, as more OSC classes and compounds were identified (thiols, sulfides, thiophenes, naphthothiophenes, benzothiophenes, and benzonaphthothiophenes). The roof-tile effect was observed for OSC and PAH in all bitumens. Several co-elutions among analytes and with matrix interferents were solved by use of GC×GC.