Performance evaluation of nickel as anode catalyst for DMFC in acidic and alkaline medium

Direct methanol fuel cell (DMFC) research is highly focused due to its high energy density, portability and inexpensive. In the present study conventional platinum catalyst used for methanol oxidation is being replaced with nickel catalyst supported over nickel mesh. The electrode is synthesized by single step electro deposition technique. Synthesized electrode was characterized by SEM, EDAX and AFM techniques to know the surface morphology, composition and thickness of the catalyst respectively. The electro catalytic behavior of the nickel for methanol oxidation was evaluated using cyclic voltammetry technique. As the DMFC is compatible with both the acidic and alkaline electrolytes the working of the nickel mesh electrode is analyzed in both media. The results showed maximum current density of 0.025 and 0.030 A/cm² in alkaline and acidic medium respectively with less potential around 0.4 and 0.2 V. The other parameters such as varying the concentration of methanol, electrolyte medium, scan rate and thickness of the catalytic layer were analyzed and optimized.     

Synthesis of Ultrafine Mesoporous Tungsten Carbide by High‐energy Ball Milling and Its Electrocatalytic Activity for Methanol Oxidation

Ultrafine mesoporous tungsten carbide (WC) was prepared from as‐synthesized mesoporous WC using high‐energy ball milling treatment. X‐ray diffraction (XRD), scanning electron microscopy (SEM), and nitrogen adsorption‐desorption techniques were used to characterize the samples. Brunauer‐Emmett‐Teller (BET) surface areas of WC samples increased with the increasing ball milling time and kept constant at 10–11 m²·g^?1 for over 9 h. The electrocatalytic properties of methanol electro‐oxidation at WC powder microelectrodes were investigated by cyclic voltammetry, chronoamperometry, and quasi‐steady‐state polarization techniques. The results reveal that ball‐milled WC exhibits higher activity for methanol electro‐oxidation than as‐synthesized mesoporous WC. The suitability of ball‐milled WC for methanol electro‐oxidation is better than platinum (Pt) micro‐disk, although the current peak is not as high as the Pt micro‐disk. Moreover, increasing the methanol concentration and reaction temperature promotes methanol electro‐oxidation on ultrafine mesoporous WC.     

Synthesis and characterization of ZnO-Al2 O3 oxides as energetic electro-catalytic material for glucose fuel cell

One of the thrust areas of research is to find an alternative fuel to meet the increasing demand for energy. Glucose is a good source of alternative fuel for clean energy and is easily available in abundance from both naturally occurring plants and industrial processes. Electrochemical oxidation of glucose in fuel cell requires high electro-catalytic surface of the electrode to produce the clean electrical energy with minimum energy losses in the cell. Pt and Pt based alloys exhibit high electro-catalytic properties but they are expensive. For energy synthesis at economically cheap price, non Pt based inexpensive high electro catalytic material is required. Electro synthesized ZnO-Al₂O₃ composite is found to exhibit high electro-catalytic properties for glucose oxidation. The Cyclic Voltammetry and Chronoamperometry curves reflect that the material is very much comparable to Pt as far as the maximum current and the steady state current delivered from the glucose oxidation are concerned. XRD image confirms the mixed oxide composite. SEM images morphology show increased 3D surface areas at higher magnification. This attributed high current delivered from electrochemical oxidation of glucose on this electrode surface.     

Photo(UV)-enhanced performance of Pt–TiO2 nanostructure electrode for methanol oxidation

We report an improved performance of Pt–TiO₂ nanostructure electrode for methanol oxidation in methanol fuel cells. The nanostructure electrode consisting of Pt nanophases and a titanium oxide matrix was fabricated by means of co-sputtering deposition method. The electrode showed a remarkably enhanced performance for methanol oxidation under UV illumination compared to that without UV illumination. Such a remarkably improved performance of the Pt–TiO₂ electrode might be due to the enhanced methanol oxidation by photo-generated holes in the TiO₂ under UV illumination.     

Pd/Pt core–shell nanowire arrays as highly effective electrocatalysts for methanol electrooxidation in direct methanol fuel cells

Highly ordered Pd/Pt–core–shell nanowire arrays (Pd/Pt NWAs) have been prepared by anodized aluminum oxide (AAO) template-electrodeposition and magnetron sputtering methods. Pd/Pt NWA electrode shows a very high electrochemical active surface area and high electrocatalytic activity for the methanol electrooxidation in acid medium for direct methanol fuel cells (DMFCs). The mass specific anodic peak current density is 756.7 mA mg⁻¹ Pt for the methanol oxidation on the Pd/Pt NWA electrode, an increase by a factor of four as compared to conventional E-TEK PtRu/C electrocatalysts. The mechanism of the significant enhancement of the Pd/Pt core/shell NWA nanostructure in the efficiency and electrocatalytic activity of Pt for the methanol electrooxidation in acid medium is discussed.     

2D Bi2WO6/MoS2 as a new photo-activated carrier for boosting electrocatalytic methanol oxidation with visible light illumination

In this paper, a new two-dimensional (2D)/2D composite of Bi₂WO₆/MoS₂ was facile synthesized, and then was used as supporting material for depositing Pt nanoparticles. The as-synthesized Pt-Bi₂WO₆/MoS₂ was extended into photo-assisted electrocatalytic oxidation of methanol, which is a model anode reaction for direct methanol fuel cell. Compare with traditional electrocatalytic process, Pt-Bi₂WO₆/MoS₂ displays 1.5 times enhanced electrocatalytic performance on methanol oxidation with assistance of visible light irradiation and 2.2 times for commercial Pt/C. Besides, from the results of chronoamperometric and chronopotentiometry experiments, the stability of Pt-Bi₂WO₆/MoS₂ electrode is clearly improved under visible light irradiation. The synergistic effects of photo- and electro-catalytic in the heterojunction of Pt-Bi₂WO₆/MoS₂ in favor of the above enhancement. This research gives more insights in the fields of photo-assisted traditional electrocatalytic application by constructing of semiconductor heterojunction carrier.     

ESR study of spin adducts of the direct electrocatalytic decomposition of light aliphatic alcohols in a polymer electrolyte fuel cell

Spin adducts of methanol and ethanol electrocatalytic oxidation were detected by the spin trap method using a tiny ?₂/O₂ fuel cell (FC) designed for ESR in situ with a Nafion/Pt membrane electrode assembly. Spin adducts of intermediates of the direct electrooxidation of ethanol, which have not been observed earlier, were obtained by the variation of oxidation conditions, in particular, the FC potential. The work of the FC was controlled by monitoring the diagnostic curves potential3-current density, power density3-current density, and efficiency—power density.     

Composite electrodes consisting Pt nano-particles and poly (aminophenols) film on pre-treated aluminum substrate as electrocatalysts for methanol oxidation

Electrochemically platinum plated aluminum (Al/Pt) was used as an electrode substrate for the electropolymerization of aminophenols and fabrication of composite electrodes based on platinum nano-particles. The poly(o-aminophenol) (PoAP), poly(m-aminophenol) (PmAP), and poly(p-aminophenol) (PpAP) were synthesized on the Al/Pt electrode, and further modification was performed by deposition of platinum nano-particles onto polymer matrixes. The electrochemical and morphological characteristic of the composed electrodes were carried out by cyclic voltammetry and scanning electron microscopy, respectively. The electrocatalytic oxidation of methanol on the composite electrodes was studied by cyclic voltammetry in 0.1 M sulfuric acid as supporting electrolyte. It was found that the Al/Pt/PoAP electrode incorporated Pt nano-particles (Al/Pt/PoAP/Pt) exhibits a higher electrocatalytic activity for the oxidation of methanol than the Al/Pt/PmAP/Pt and Al/Pt/PpAP/Pt electrodes. On the other hand, a higher catalytic current for methanol oxidation was found on the Al/Pt/PoAP/Pt electrode in comparison to bulk Pt and Al–Pt (Al with 0.2 mg cm⁻² of Pt particles) electrodes. The effects of various parameters such as thickness of the polymer film, concentration of the monomer, Pt loading method and the Pt amounts, concentration of the methanol, and the medium temperature were studied on the electrooxidation of methanol. The long-term stability of the modified electrode has also been investigated.     

Electrodeposition and electrocatalytic properties of platinum nanoparticles on multi-walled carbon nanotubes: effect of the deposition conditions

Platinum (Pt) nanoparticles were electrochemically deposited on multi-walled carbon nanotubes (MWCNTs) through a three-step process, including an electrochemical treatment of MWCNT, electro-oxidation of PtCl₄ ²⁻ to Pt(IV) complex, and an electro-conversion of Pt(0) on MWCNT. The effect of formation conditions for Pt(IV) complexes on the Pt nanoparticals transformed was investigated. The structure and elemental composition of the resulting Pt/MWCNT electrode were characterized by transmission electron micrograph (TEM) and energy dispersive X-ray spectroscopy (EDX). The electrocatalytic properties of the resulting Pt/MWCNT electrode for methanol oxidation have been investigated. The high electrocatalytic activity and good stability of Pt/MWCNT electrode may be attributed to the high dispersion of platinum nanoparticles and the particular properties of the MWCNT supports.     

碳黑预处理对Pt/C催化剂对甲醇氧化电催化活性的影响

直接甲醇燃料电池(DMFC)由于具有较多的优点而受到广泛的关注. 但是碳载Pt (Pt/C)阳极催化剂电催化活性低是限制其应用的一个主要问题. 为了提高Pt/C催化剂对甲醇氧化的电催化性能, 分别用CO₂, 空气, H₂O₂或HNO₃对常用作为载体的Vulcan XC-72碳黑进行预处理. 结果表明, 在用CO₂, 空气, HNO₃, H₂O₂处理的及未处理的碳黑作载体制得的Pt/C催化剂电极上, 甲醇氧化峰的峰电流密度顺序为39, 33, 32, 20和18 mA•cm^－2, 表明用CO₂处理的碳载体制备的Pt/C催化剂对甲醇氧化有最好的电催化活性和稳定性. 其主要原因是用CO₂处理能减少碳黑表面的含氧基团和增加石墨化程度, 而使碳黑的电阻降低及Pt粒子在碳黑上的分散性变好.     

The effect of electrochemically treated glassy carbon on the activity of supported Pt catalyst in methanol oxidation

Effect of electrochemical oxidation of glassy carbon on deposition of platinum particles and electrocatalytic activity of platinum supported on oxidized glassy carbon (Pt/GC_OX) were studied for methanol oxidation in H₂SO₄ solution. Platinum was potentiostatically deposited from H₂SO₄ + H₂PtCl₆ solution. Glassy carbon was anodically polarised in 0.5 M H₂SO₄ at 2.25 V vs. saturated calomel electrode (SCE) during 35 s. Electrochemical treatment of GC support, affecting not significantly the real Pt surface area, leads to a better distribution of platinum on the substrate and has remarkable effect on the activity. The activity of the Pt/GC_OX electrode for methanol oxidation is larger than polycrystalline Pt and for more than one order of magnitude larger than Pt/GC electrode. This increase in activity indicates the pronounced role of organic residues of GC support on the properties of Pt particles deposited on glassy carbon.     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

Electrochemical synthesis of a novel platinum nanostructure on a glassy carbon electrode, and its application to the electrooxidation of methanol

We show that the addition of white dextrin during the electrochemical deposition of platinum nanostructures (nano-Pt) on a glassy carbon electrode (GCE) results in an electrochemically active surface that is much larger than that of platinum microparticles prepared by the same procedure but in the absence of dextrin. The nano-Pt deposits are characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy, and electrochemical methods. The SEM images reveal deposits composed of mainly nanoparticles and short nanorods. The GCE was applied as a novel and cost-effective catalyst for methanol oxidation. The use of nano-Pt improves the electrocatalytic activity and the stability of the electrodes.

Electrocatalytic mechanism and kinetics of SOMs oxidation on ordered PtPb and PtBi intermetallic compounds: DEMS and FTIRS study

The electrocatalytic activities and mechanisms of PtPb and PtBi ordered intermetallic phases towards formic acid, formaldehyde and methanol oxidation have been studied by DEMS and FTIRS, and the results compared to those for a pure polycrystalline platinum electrode. While PtPb exhibits an enhanced electrocatalytic activity for the oxidation of all three organic molecules when compared to a Pt electrode, PtBi exhibits an enhanced catalytic activity towards formic acid and formaldehyde oxidation, but not methanol. FTIRS data indicate that adsorbed CO does not form on PtPb or PtBi intermetallic compounds during the oxidation of formic acid, formaldehyde and methanol, and therefore their oxidation on both PtPb and PtBi intermetallic compounds proceeds via a non-CO(ads) pathway. Quantitative DEMS measurements indicate that only CO(2) was detected as a final product during formic acid oxidation on Pt, PtPb and PtBi electrodes. At a smooth polycrystalline platinum electrode, the oxidation of formaldehyde and methanol produces mainly intermediates (formaldehyde and formic acid), while CO(2) is a minor product. In contrast, CO(2) is the major product for formaldehyde and methanol oxidation at a PtPb electrode. The high current efficiency of CO(2) formation for methanol and formaldehyde oxidation at a PtPb electrode can be ascribed to the complete dehydrogenation of formaldehyde and formic acid due to electronic effects. The low onset potential, high current density and high CO(2) yield make PtPb one of the most promising electrocatalysts for fuel cell applications using small organic molecules as fuels.     

Preparation and electrochemical performance of graphene–Pt black nanocomposite for electrochemical methanol oxidation

This work reports the preparation, characterization, and electrocatalytic characteristics of a new metallic nanocatalyst. The catalyst, Pt black–graphene oxide (Pt-GO), was prepared by deposition of Pt black on the surface of graphene oxide nanosheet and characterized by transmission electron microscopy (TEM), energy-dispersive spectroscopy (EDS), and voltammetry. The Pt-graphene (Pt-GR) composite modified glassy carbon electrode (Pt-GR/GCE) was prepared with cyclic voltammetric scanning of Pt-GO/GCE in the potential range from ?1.5 to 0.2 in 0.1 M phosphate buffer solution at 50 mV·s^?1 for 5 cycles. The electrocatalytic properties of the Pt-GR/GCE for methanol (CH₃OH) oxidation have been investigated by cyclic voltammetry (CV); high electrocatalytic activity of the Pt-GR/GCE can be observed. This may be attributed to the high dispersion of Pt catalyst and the particular properties of GR support. The long-term stability of Pt-GR composite was investigated in 0.05 M CH₃OH in 0.1 M H₂SO₄ solution. It can be observed that the peak current decreases gradually with the successive scans. The loss may result from the consumption of methanol during the CV scan. It also may be due to the poisoning organic compounds. The results imply that the Pt-GR composite has good potential applications in fuel cells.     

Electrocatalytic Acitivity of rGO/PEDOT : PSS Nanocomposite towards Methanol Oxidation in Alkaline Media

Increasing demand of alternative energy sources leads to the development of new electrocatalytic materials for fuel cells. In present work, we report the synthesis of rGO/PEDOT : PSS (reduced graphene oxide/ Poly (3,4‐ethylenedioxythiophene) : Polystyrene sulfonate) nanocomposite by in‐situ polymerization method using EDOT as precursor and the nanocomposite is used as anode catalyst for methanol oxidation. Structural and chemical characterizations such as XRD, FTIR and Micro‐Raman confirm the formation of the nanocomposite. From TEM image, growth of nanofibrous PEDOT : PSS on rGO nanosheets is observed. Electrochemical characterizations of rGO/PEDOT : PSS/ITO electrode are performed by Cyclic Voltammetry (CV), Electrochemical Impedance Spectroscopy (EIS) and Chronoamperometry (CA) measurements. Methanol oxidation reactions are performed in 0.5 M NaOH solution. The anodic current of the nanocomposite coated ITO is found be 37.5 mA at 0.59 V due to methanol electro‐oxidation and retentivity of the electrode is 92 % of initial scan after 800 cycles. The chronoamperometric results reveal that the nanocomposite modified electrode exhibits better stability with retention factor of 42.4 % up to 3000 seconds. The rGO/PEDOT : PSS/ITO electrode exhibits enhanced electrocatalytic activity towards methanol oxidation reaction due to larger surface area and excellent conductivity of rGO nanosheet.     

A new simple preparation of platinum-nickel alloy nanoparticles and their characterization as an electrocatalyst for methanol oxidation

Pt-Ni alloy nanoparticles were produced by casting 2 or 10 mM H₂PtCl₆ solutions on a Ni column. The apparent particle size for the resultant Pt-Ni alloys increased with the concentration of the H₂PtCl₆ solution, while the content of Pt in the alloy decreased. The potential sweeps of 5 cycles in an H₂SO₄ aqueous solution for Pt-Ni (2 mM)/Ni and Pt-Ni (10 mM)/Ni electrodes led to electrochemical behavior similar to a polycrystalline Pt electrode, suggesting the formation of a few thin Pt layers on each Pt-Ni alloy surface. In electrochemical measurements, both Pt-Ni/Ni electrodes showed more negative onset potential of methanol oxidation and slower degradation of oxidation current of methanol than the polycrystalline Pt electrode. X-ray photoelectron spectroscopy of both Pt-Ni/Ni electrodes showed the shift of Pt4f peaks to a higher binding energy, suggesting that the increase in the d vacancy in the balance band 5d orbital of Pt contributed to the improved electrocatalytic activity and durability of the Pt-Ni/Ni electrodes.     

Exploration of electrodeposited platinum alloy catalysts for methanol electro-oxidation in 0.5 M H<Subscript>2</Subscript>SO<Subscript>4</Subscript>: Pt-Ni system

In this work, we examine the electrocatalytic activity of electrodeposited Platinum (Pt)-Nickel (Ni) alloy layers on an inert substrate electrode for methanol oxidation reaction. Analyses using energy-dispersive fluorescent X-ray analysis and powder X-ray diffractometry confirm alloying of Pt with Ni in a range of compositions. Steady-state polarisation measurements in 0.5 M methanol+0.5 M H₂SO₄ solutions clearly show that the onset of electro-oxidation shifts to less anodic potential values (approximately 160 mV), while also exhibiting current enhancements up to ~15 times the currents obtained for the pure Pt electrodeposit. A linear relationship between the cyclic voltammetric peak (oxidation) current and [MeOH] is observed at a scan rate of 50 mVs^–1, thus indicating reduced influence of adsorbed CO (CO_ads) surface poison. A critical composition, Pt (92%)/Ni (8%) [denoted Pt-Ni(3) alloy] is found to exhibit maximum electrocatalytic activity, beyond which the activity drops, whereas pure Ni does not catalyse the reaction. While the promotion of electro-oxidation is understood to be largely due to the alloy catalyst, surface redox species of Ni oxide formed during the electro-oxidation process may also contribute to the oxygenation of CO_ads, thereby enhancing the oxidation current. Plausible mechanisms of methanol oxidation on Pt/ transition metal alloy electrocatalysts are discussed in terms of electron transfer (in the alloy) and the role of Ni oxide species.     

Controllable Electrodeposition of Platinum Nanoparticles on Graphene Nanosheet for Methanol Oxidation Reaction

A simple and cost-effective electrochemical method synthesized platinum nanoparticles on graphene nanosheet (PtNPs@GNS) is reported, and the Pt loading of the PtNPs@GNS can be controlled by electrodeposition. The structure and element analysis of the PtNPs@GNS have been investigated by scanning electron microscopy (SEM), Raman spectrum, X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS). The electrochemical measurement including electrochemical active surface area, current density, mass activity, oxidation peak potential,shows the PtNPs@GNS have more performance electrocatalytic properties for methanol oxidation reaction (MOR) compared to Vulcan XC-72 carbon (XC-72) supported PtNPs electrocatalysts. Probably, the cause which may be attributes to no aggregation of PtNPs and the well-dispersion on surface of GNS, so PtNPs@GNS show large electrochemically active surface area, highly electrocatalytic activity and stability in direct methanol fuel cells.     

Dealloying of Mesoporous PtCu Alloy Film for the Synthesis of Mesoporous Pt Films with High Electrocatalytic Activity

Mesoporous Pt film with highly electrocatalytic activity is successfully synthesized by dealloying of mesoporous PtCu alloy film prepared through electrochemical micelle assembly. The resulting mesoporous electrode exhibits high current density and superior stability toward the methanol oxidation reaction.