Development of methodologies to determine aluminum, cadmium, chromium and lead in drinking water by ET AAS using permanent modifiers

In this work, methodologies were developed to determine aluminum (Al), cadmium chromium and lead in drinking water by electrothermal atomic absorption spectrometry using permanent modifiers. No use of modifier, iridium, ruthenium, rhodium and zirconium (independently, 500 μg) were tested to each one analyte through the pyrolysis and atomization temperatures curves. As the matrix is very simple, did not had occurred problems with the background for all metals. The best results obtained for cadmium and chromium was with the use of rhodium permanent modifier. For lead and aluminum, the best choice was the use of zirconium. The selection for the modifier took into account the sensitivity, form of the absorption pulse and low atomization temperature (what contributes to elevate the useful life of the graphite tube). For aluminum using zirconium permanent, the best pyrolysis and atomization temperatures were respectively, of 1000 and 2500 °C with a characteristic mass (1% of absorbance, m_o) of 19 pg (recommended of 20 pg). For cadmium, with use of rhodium the best temperatures for the pyrolysis and atomization were respectively of 400 and 1100 °C, with a symmetrical peak and with a m_o of 1.0 pg (recommended of 1.0 pg). For chromium with rhodium permanent, the best temperatures for pyrolysis and atomization were respectively of 1000 and 2200 °C, with symmetrical peak and m_o of 5.3 pg (recommended of 5.5 pg). For lead with zirconium permanent, the best temperatures for pyrolysis and atomization were of 700 and 2400 °C, with symmetrical peak and with m_o of 30 pg (recommended of 20 pg). Water samples spiked with each one of the metals in four different levels inside of the acceptable values presented recoveries always close to 100%. The detection limits were of 0.1 μg l⁻¹ for cadmium; 0.2 μg l⁻¹ for chromium; 0.5 μg l⁻¹ for lead and 1.4 μg l⁻¹ for aluminum.     

Comparison of direct solid sampling and slurry sampling for the determination of cadmium in wheat flour by electrothermal atomic absorption spectrometry

Two analytical methods for the determination of cadmium in wheat flour by electrothermal atomic absorption spectrometry without prior sample digestion have been compared: direct solid sampling analysis (SS) and slurry sampling (SlS). Besides the conventional modifier mixture of palladium and magnesium nitrates (10 μg Pd + 3 μg Mg), 0.05% (v/v) Triton X-100 has been added to improve the penetration of the modifier solution into the solid sample, and 0.1% H₂O₂ in order to promote an in situ digestion for SS. For SlS, 30 μg Pd, 12 μg Mg and 0.05% (v/v) Triton X-100 have been used as the modifier mixture. Under these conditions, and using a pyrolysis temperature of 800 °C, essentially no background absorption was observed with an atomization temperature of 1600 °C. About 2 mg of sample have been typically used for SS, although as much as 3-5 mg could have been introduced. In the case of SlS multiple injections had to be used to achieve the sensitivity required for this determination. Calibration against aqueous standards was feasible for both methods. The characteristic mass obtained with SS was 0.6 pg, and that with SlS was 1.0 pg. The limits of detection were 0.4 and 0.7 ng g⁻¹, the limits of quantification were 1.3 and 2.3 ng g⁻¹ and the relative standard deviation (n = 5) was 6-16% and 9-23% for SS and SlS, respectively. The accuracy was confirmed by the analysis of certified reference materials. The two methods were applied for the determination of cadmium in six wheat flour samples acquired in supermarkets of different Brazilian cities. The cadmium content varied between 8.9 ± 0.5 and 13 ± 2 ng g⁻¹ (n = 5). Direct SS gave results similar to those obtained with SlS using multi-injections; the values of both techniques showed no statistically significant difference at the 95% confidence level. Direct SS was finally adopted as the method of choice, due to its greater simplicity, the faster speed of analysis and the better figures of merit.     

Method development for the determination of cadmium in fertilizer samples using high-resolution continuum source graphite furnace atomic absorption spectrometry and slurry sampling

The determination of cadmium (Cd) in fertilizers is of major interest, as this element can cause growth problems in plants, and also affect animals and humans. High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) with charge-coupled device (CCD) array detection overcomes several of the limitations encountered with conventional line source AAS, especially the problem of accurate background measurement and correction. In this work an analytical method has been developed to determine Cd in fertilizer samples by HR-CS GF AAS using slurry sampling. Both a mixture of 10 μg Pd + 6 μg Mg in solution and 400 μg of iridium as permanent modifier have been investigated and aqueous standards were used for calibration. Pyrolysis and atomization temperatures were 600 °C and 1600 °C for the Pd-Mg modifier, and 500 °C and 1600 °C for Ir, respectively. The results obtained for Cd in the certified reference material NIST SRM 695 (Trace Elements in Multi-Nutrient Fertilizer) of 16.7 ± 1.3 μg g⁻¹ and 16.4 ± 0.75 μg g⁻¹ for the Pd-Mg and Ir modifier, respectively, were statistically not different from the certified value of 16.9 ± 0.2 μg g⁻¹ on a 95% confidence level; however, the results obtained with the Ir modifier were significantly lower than those for the Pd-Mg modifier for most of the samples. The characteristic mass was 1.0 pg for the Pd-Mg modifier and 1.1 pg Cd for the Ir modifier, and the correlation coefficients (R²) of the calibration were > 0.99. The instrumental limits of detection were 7.5 and 7.9 ng g⁻¹, and the limits of quantification were 25 and 27 ng g⁻¹ for Pd-Mg and Ir, respectively, based on a sample mass of 5 mg. The cadmium concentration in the investigated samples was between 0.07 and 5.5 μg g⁻¹ Cd, and hence below the maximum value of 20 μg g⁻¹ Cd permitted by Brazilian legislation.     

Determination of selenium in human milk by electrothermal atomic absorption spectrometry and chemical modification

A method was developed for the determination of selenium in human milk using electrothermal atomic absorption spectrometry. The use of chemical modifiers as well as their implications during the pyrolysis step was examined. The chemical modifiers that were studied were Zr, Ir as well as the mixed modifier Zr-Ir. The Ir modifier stabilized selenium at 1000 °C, Zr at 800 °C, while the mixed modifier at 1200 °C. The effect of modifier mass was studied and was found that better results are achieved with addition of 2 μg Zr and 2 μg Ir. The characteristic masses of selenium in the presence of Zr, Ir and the mixed modifier were found to be 73.3, 18.0 and 14.7 pg, respectively, while the corresponding limits of detection were found 2.0, 0.50 and 0.41 μg l⁻¹. Consequently better results were obtained with the mixed modifier. The developed method was applied for the determination of selenium in human milk, which was digested with a HNO₃ + H₂O₂ mixture in a microwave oven. The limit of detection of the method was 1.37 μg l⁻¹, the characteristic mass, m₀, was 48.8 pg and the repeatability was less than 5% as R.S.D.(%). Matrix matched calibration was used. Recoveries were estimated to be 93-105%. The method was applied to breast milk of Greek women (n = 9) and the Se content was found to be in the range 16.7-42.6 μg l⁻¹ with mean value 27.4 ± 5.5 μg l⁻¹.     

Rhodium and iridium complexes of N-heterocyclic carbenes: Structural investigations and their catalytic properties in the borylation reaction

Bridged and unbridged N-heterocyclic carbene (NHC) ligands are metalated with [Ir/Rh(COD)₂Cl]₂ to give rhodium(I/III) and iridium(I) mono- and biscarbene substituted complexes. All complexes were characterized by spectroscopy, in addition [Ir(COD)(NHC)₂][Cl,I] [COD = 1,5-cyclooctadiene, NHC =  1,3-dimethyl- or 1,3-dicyclohexylimidazolin-2-ylidene] (1, 4), and the biscarbene chelate complexes 12 [(η⁴-1,5-cyclooctadiene)(1,1′-di-n-butyl-3,3′-ethylene-diimidazolin-2,2′-diylidene)iridium(I) bromide] and 14 [(η⁴-1,5-cyclooctadiene)(1,1′-dimethyl-3,3′-o-xylylene-diimidazolin-2,2′-diylidene)iridium(I) bromide] were characterized by single crystal X-ray analysis. The relative σ-donor/π-acceptor qualities of various NHC ligands were examined and classified in monosubstituted NHC-Rh and NHC-Ir dicarbonyl complexes by means of IR spectroscopy. For the first time, bis(carbene) substituted iridium complexes were used as catalysts in the synthesis of arylboronic acids starting from pinacolborane and arene derivatives.     

Spectrofluorimetric determination of iridium(IV) traces using 4-pyridone derivatives

A new spectrofluorimetric determination of iridium(IV) with 3-hydroxy-2-methyl-1-phenyl-4-pyridone (HX) or 3-hydroxy-2-methyl-1-(4-tolyl)-4-pyridone (HY) is reported. Iridium(IV) react with HX or HY and chelates were extracted into chloroform or dichloromethane. The organic phase showed fluorescence. The fluorescence measurements to quantify iridium were carried out in its fluorescent band centred at λ_ex=373 nm and λ_em=480 nm. Under optimal conditions, the calibration graphs were linear over the concentration range of 0.1-7.6 μg ml⁻¹ of iridium for Ir(IV)-HX and 0.1-5.8 μg ml⁻¹ for Ir(IV)-HY with a correlation coefficients of 0.999 and 0.992 and relative standard deviation of ±1.1%.The method is free from interference by Rh(III) and Pt(IV), which normally interfere with other methods. Iridium can be determined in the presence of 300-fold excess of rhodium(III) and 10-fold excess of platinum(IV).The method was applied successfully to the determination of iridium in some synthetic mixtures and mineral sample gave satisfactory results.     

A comparative study of chemical modifiers in the determination of total arsenic in marine food by tungsten coil electrothermal atomic absorption spectrometry

Three platinum group elements (Pd, Ir and Rh) both in solution and in pre-reduced form, and also combined with Mg(NO₃)₂ or ascorbic acid, were assessed as possible chemical modifiers on the atomization of As in digest solutions of seafood matrices (clam and fish tissue) by tungsten coil electrothermal atomic absorption spectrometry (TCA-AAS) and compared without a modifier. Of 28 modifier alternatives in study including single form and binary mixtures, and based on maximum pyrolysis temperature without significant As loss and best As absorbance sensitivity during atomization, three modifiers: Rh (0.5 μg), Ir (1.0 μg) and Rh (0.5 μg) + ascorbic acid (0.5 μg), at optimum amounts were pre-selected and compared. The definitive modifier (rhodium (0.5 μg)) was selected by variance analysis. The mean within-day repeatability was 3% in consecutive measurements (25-300 μg l⁻¹) (three cycles, each of n = 6) and showed good short-term stability of the absorbance measurements. The mean reproducibility was 4% (n = 18 in a 3-day period) and the detection limit (3σ_blank/slope) was 42 pg (n = 16). Quantitation was by standard additions to compensate for matrix effects not corrected by the modifier. Three sample digestion procedures were compared in fish and clam tissue samples: microwave acid digestion alone (A) or combined with the addition of 2% (m/v) K₂S₂O₈ solution followed either by UV photo-oxidation (B) or re-digestion in a thermal block (C). The accuracy was established by determination of As in certified reference material of dogfish muscle (DORM-2). Procedures B and C showed good recoveries (102% (n = 4) and 103% (n = 7), respectively), whereas procedure A was not quantitative (85%). The methodology is simple, fast, reliable, of low cost and was applied to the determination of total As in lyophilized samples of clam and fish collected in the Chilean coast.     

Interference-free determination of thallium in aqua regia leaches from rocks, soils and sediments by D(2)-ETAAS method using mixed palladium-citric acid-lithium chemical modifier

The mixture of palladium (chloride) with citric acid and lithium is proposed as a new chemical modifier for the elimination of interference occurred during the determination of Tl in aqua regia extracts from rocks, soils and sediments by electrothermal atomic absorption spectrometry using instrumentation with deuterium-lamp background correction (D₂-ETAAS). Palladium was preferred to rhodium and platinum as to analyte stabilization, citric acid served as an effective reducing agent facilitating formation of Pd-Tl stable covalent bonds playing an important role in the analyte stabilization. Citric acid in addition helps to remove most of interfering chloride at low temperature. The further addition of Li increased significantly the robustness of chemical modifier against strongly interfering ZnCl₂ matrix by binding free chlorine into a more stable LiCl molecule. In the presence of the proposed chemical modifier the temperature for the final step of pyrolysis was adjustable up to 1000 °C, without any noticeable loss of volatile Tl species and the interference of the rest chloride matrix was significantly reduced. The application of the modifier to direct determination of Tl in aqua regia extracts from rocks, soils and sediments has ensured the characteristic mass and LOD value for the original sample 13 pg and 0.043 μg g⁻¹, respectively (10-μL aliquots of sample) and has enabled the use of matrix-free standard solutions for attaining accurate analysis. The accuracy was verified by the analysis of certified reference samples and by the comparison of results with those found by an inductively coupled plasma orthogonal acceleration time-of-flight mass spectrometer (ICP-oa-TOFMS) method.     

Study of binding and denaturation dynamics of IgG and anti-IgG using dual color fluorescence correlation spectroscopy

In this article, we present a systematic study on IgG and Fab fragment of anti-IgG molecules using fluorescence auto- and cross-correlation spectroscopy to investigate their diffusion characteristics, binding kinetics, and the effect of small organic molecule, urea on their binding. Through our analysis, we found that the diffusion coefficient for IgG and Fab fragment of anti-IgG molecules were 37 ± 2 μm² s⁻¹ and 56 ± 2 μm² s⁻¹, respectively. From the binding kinetics study, the respective forward (k_a) and backward (k_d) reaction rates were (5.25 ± 0.25) × 10⁶ M⁻¹ s⁻¹ and 0.08 ± 0.005 s⁻¹, respectively and the corresponding dissociation binding constant (K_D) was 15 ± 2 nM. We also found that urea inhibits the binding of these molecules at 4 M concentration due to denaturation.     

Cobalt as internal standard for arsenic and selenium determination in urine by simultaneous atomic absorption spectrometry

The effectiveness of internal standardization for simultaneous atomic absorption spectrometry (SIMAAS) was investigated for As and Se determination in urine. Co and Sn were selected as internal standard (IS) candidates based on the evaluation of some physico-chemical parameters related to the atomization. Correlation graphs, plotted from the normalized absorbance signals (n = 20) of internal standard (axis y) versus analyte (axis x), precision, and accuracy of the analytical results were the supportive parameters to choose Co as the most appropriate IS. The urine samples were diluted 1 + 2 to 1.0% (v/v) HNO₃ + 80 μg L⁻¹ Co²⁺. The mixture 20 μg Pd + 3 μg Mg was used as chemical modifier and the optimized temperatures for pyrolysis and atomization steps were 1400 and 2300 °C, respectively. The characteristic masses for As (47 ± 1 pg) and Se (72 ± 2 pg) were estimated from the analytical curves. The detection limits (n = 20, 3δ) were 1.8 ± 0.1 and 2.6 ± 0.1 μg L⁻¹ for As and Se, respectively. The reliability of the entire procedure was checked with the analysis of certified reference material from Sero AS(Seronorm™ Trace Elements in Urine). The obtained results showed the matrix interference disallowed the instrument calibration with aqueous standards. The best analytical condition was achieved when matrix-matched standards were used in combination with Co as IS, which improved the recoveries obtained for As. Under this experimental condition, eight urine samples were analysed and spiked with 10 and 25 μg L⁻¹ As and Se. The mean recoveries were 96 ± 6% (10 μg L⁻¹ As), 95 ± 6% (25 μg L⁻¹ As), 101 ± 7% (10 μg L⁻¹ Se), and 97 ± 4% (25 μg L⁻¹ Se).     

Application of heteroleptic iridium complexes with fluorenyl-modified 1-phenylisoquinoline ligand for high-efficiency red polymer light-emitting devices

A series of new heteroleptic iridium complexes bearing fluorenyl-modified 1-phenylisoquinoline as the first ligand and different ancillary ligands has been prepared and characterized. These complexes bis(1-(3-(9,9-dimethyl-fluoren-2-yl)phenyl)isoquinoline-C2,N′)iridium(III)acetylacetonate(Ir(DMFPQ)₂acac)), bis(1-(3-(9,9-dimethyl-fluoren-2-yl)phenyl)isoquinoline-C2,N′)iridium(III)(3-(pyridin-2-yl)-1,2,4-triazolate)(Ir(DMFPQ)₂pt) and bis(1-(3-(9,9-dimethyl-fluoren-2-yl)phenyl)isoquinoline-C2,N′)iridium(III)(2-(2-pyridyl)benzimidazolate)(Ir(DMFPQ)₂pbi) showed red phosphorescent emissions of 615-630 nm in dichloromethane solution. The device fabricated with these complexes doped into a host polyfluorene (PFO) blend with 30% of an electron transport material 2-(4-biphenyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD) showed high device efficiencies. Ir(DMFPQ)₂acac exhibited red emission with an external quantum efficiency(η_ext) of 14.3% and luminous efficiency(η_c) of 7.8 cd/A at 1.2 mA/cm² and the maximum brightness reached 10 006 cd/m² (Commission Internationale de I’Eclairage(CIE) chromaticity coordinates: (0.67, 0.32)) at 412 mA/cm². Ir(DMFPQ)₂pt showed a η_ext of 13.0% and η_c of 9.2 cd/A at 17 mA/cm², 1532 cd/m², and the maximum brightness reached 15085 cd/m² (CIE: 0.64, 0.34) at 360 mA/cm².     

Correction of structured molecular background by means of high-resolution continuum source electrothermal atomic absorption spectrometry—Determination of antimony in sediment reference materials using direct solid sampling

A simple, fast and accurate procedure is proposed for the determination of antimony in certified sediment reference materials using direct solid sampling high-resolution continuum source electrothermal atomic absorption spectrometry and iridium as a permanent modifier. The less sensitive resonance line at 231.147 nm has been used in order to allow the introduction of larger sample mass. Six certified reference materials, one river, one estuarine and four marine sediments have been analyzed. The use of iridium as a permanent modifier caused an increase of 30% in sensitivity and stabilized antimony in the sediment to a pyrolysis temperature of 1100 °C. Significant background absorption with pronounced rotational fine structure was observed at the optimum atomization temperature of 2100 °C, which coincided with the analyte atomic absorption in time. This background was found to be due to the electron excitation spectra of mostly the SiO and in part the PO molecules, and could be eliminated by applying a least-squares background correction algorithm. A characteristic mass of 28 pg Sb was obtained, and the limit of detection (3σ, n = 10) was 0.02 μg g⁻¹, calculated for 0.2 mg of sample. The results obtained for six certified reference materials with concentrations between 0.40 and 11.6 ± 2.6 μg g⁻¹ Sb were in agreement with the certified values according to a Student's t-test for a 95% confidence level, using aqueous standards for calibration. The precision, expressed as relative standard deviation, ranged between 7% and 17% (n = 5).     

Thermodynamic properties of hydrated sodium l-threonate Na(C4H7O5)·H2O(s)

Low-temperature heat capacities of the compound Na(C₄H₇O₅)·H₂O(s) have been measured with an automated adiabatic calorimeter. A solid-solid phase transition and dehydration occur at 290-318 K and 367-373 K, respectively. The enthalpy and entropy of the solid-solid transition are Δ_transH_m = (5.75 ± 0.01) kJ mol⁻¹ and Δ_transS_m = (18.47 ± 0.02) J K⁻¹ mol⁻¹. The enthalpy and entropy of the dehydration are Δ_dH_m = (15.35 ± 0.03) kJ mol⁻¹ and Δ_dS_m = (41.35 ± 0.08) J K⁻¹ mol⁻¹. Experimental values of heat capacities for the solids (I and II) and the solid-liquid mixture (III) have been fitted to polynomial equations.     

Purine-based carbenes at rhodium and iridium

Purine-based carbenes can be attached to catalysis-related metals like rhodium and iridium through the standard method of in situ deprotonation of the respective azolium salts. Thus, 1,3,7,9-tetramethylxanthinium tetrafluoroborate is obtained by the reaction of trimethyloxonium tetrafluoroborate and caffeine. The salt and 7,9-dimethylhypoxanthinium iodide were used as a consecutive precursor to form rhodium (I) and iridium (I) carbene complexes of the type [M(L)(L_Carbene)₂]I and M(L)(L_Carbene)(I) (M = Rh, Ir, L_Carbene = 1,3,7,9-tetramethylxanthine-8-ylidene, 7,9-dimethylhypoxanthine-8-ylidene, L = η⁴-1,5-COD, CO) (COD = 1,5-cyclooctadiene). All compounds were characterized by ¹H NMR, ¹³C NMR, mass spectrometry and/or elemental analysis.     

Enthalpy change and mechanism of oxidation of o-phenylenediamine by hydrogen peroxide catalyzed by horseradish peroxidase

The hydrogen peroxide-oxidation of o-phenylenediamine (OPD) catalyzed by horseradish peroxidase (HRP) at 37 °C in 50 mM phosphate buffer (pH 7.0) was studied by calorimetry. The apparent molar reaction enthalpy with respect to OPD and hydrogen peroxide were −447 ± 8 kJ mol⁻¹ and −298 ± 9 kJ mol⁻¹, respectively. Oxidation of OPD by H₂O₂ catalyzed by HRP (1.25 nM) at pH 7.0 and 37 °C follows a ping-pong mechanism. The maximum rate V_max (0.91 ± 0.05 μM s⁻¹), Michaelis constant for OPD K_m,S (51 ± 3 μM), Michaelis constant for hydrogen peroxide Km,H₂O₂ (136 ± 8 μM), the catalytic constant k_cat (364 ± 18 s⁻¹) and the second-order rate constants k₊₁ = (2.7 ± 0.3) × 10⁶ M⁻¹ s⁻¹ and k₊₅ = (7.1 ± 0.8) × 10⁶ M⁻¹ s⁻¹ were obtained by the initial rate method.     

Study on the simultaneous determination of some essential and toxic trace elements in honey by multi-element graphite furnace atomic absorption spectrometry

A multi-element graphite furnace atomic absorption spectrometry (GFAAS) method was elaborated and applied for the simultaneous determination of As, Cd, Cr, Cu, and Pb in various kinds of honey samples (acacia, floral, linden, rape, and milkweed) using the transversally heated graphite atomiser (THGA) with end-capped tubes and integrated graphite platforms (IGPs). For comparative GFAAS analysis, direct (without digestion) and indirect (with digestion in a microwave oven) sample preparation procedures were tested. The effects of several chemical modifiers, such as NH₄H₂PO₄, NH₄H₂PO₄-Mg(NO₃)₂, and Pd(NO₃)₂-Mg(NO₃)₂, were studied to obtain optimal pyrolysis and atomization conditions for the set of analytes studied. The most efficient modifier was proved to be the mixture of 5 μg Pd (applied as nitrate) plus 3 μg Mg(NO₃)₂, allowing the optimal 600 °C pyrolysis and 2300 °C atomization temperatures. To prevent the sputtering and foaming of the matrix during the drying and pyrolysis steps of the furnace heating program, the sample and modifier solutions (20 + 5 μl, respectively) were dispensed together onto the IGP of the THGA pre-heated at 80 °C.The effect of increasing concentration of honey matrix was studied on the integrated absorbance (A_int) signals of analytes. The A_int signals of Cr and Pb were not altered up to 10% (m/v) matrix content in the sample solutions. The matrix effect was slightly suppressive on the A_int signals of As, Cd, and Cu above 2% (m/v) honey concentration. The recovery was found to be ranged between 85 and 115% for Cd, Cr, Cu, and Pb, whereas it was a lower, compromise value of 70-99% for As. The limit of detection (LOD) data were 1, 0.04, 0.09, 0.3, and 0.6 μg l⁻¹ for As, Cd, Cr, Cu, and Pb, respectively, which values correspond to 20, 0.8, 1.8, 5.3, and 12 ng g⁻¹, respectively, in the solid samples. The characteristic masses were found to be 21 pg As, 1.3 pg Cd, 4 pg Cr, 12 pg Cu, and 33 pg Pb. The As, Cd, Cr, Cu, and Pb contents of the studied 42 honey samples varied significantly, i.e. from below the LOD up to 13, 3.3, 109, 445, and 163 ng g⁻¹, respectively.     

Determination of pKa value, kinetic studies of decomposition and oxygen transfer for chromium(VI) peroxide

The determination of pK_a value for the unstable chromium(VI) peroxide, CrO(O₂)₂(H₂O) in aqueous solution is presented. The pK_a value is found to be (1.55 ± 0.03). The kinetic decomposition of chromium(VI) peroxide is dependent on the concentration of hydrogen peroxide in the pH range between 2.5 and 4.0. We have proposed the possible explanation for the formation of triperoxo chromium complex of hydrogen peroxide which is dependent on decomposition. Activation of coordinate peroxide in chromium(VI) peroxide observed in the kinetic studies is by reduction of thiolato-cobalt(III) complex. The rate constant (M⁻¹ s⁻¹, 15 °C) for the oxygen atom transfer reaction from CrO(O₂)₂(OH)⁻ to (en)₂Co(SCH₂CH₂NH₂)²⁺ is found to be (25.0 ± 1.3).     

Synthesis and structure of N-heterocyclic carbene complexes of rhodium and iridium derived from an imidazolium-linked cyclophane

This paper describes the synthesis, spectroscopic and structural characterisation, and electrochemical behaviour of some rhodium and iridium complexes of the form LM(X₁)(X₂)⁺, where L is a chelating bis(carbene) derived from an imidazolium-linked ortho-cyclophane. The complexes where X₁/X₂ = 1,5-cycooctadiene or norbornadiene were prepared from the imidazolium-linked cyclophane and the appropriate metal source. In these complexes, the M-L bonding was quite robust, but the diene could be displaced by CO to give the dicarbonyl complexes , from which one or both carbonyl ligands could be displaced by monodentate or bidentate phosphines, respectively. Structural studies revealed only minor variations in the cyclophane unit upon exchange of the ancillary ligands, in each case the rhodium complex being isomorphous with its iridium analogue. In cyclovoltammetric studies of LRh(dppe)⁺, reversible Rh(I/II) and Rh(II/III) redox couples were observed. The other rhodium complexes displayed more complex electrochemical behaviours and did not undergo simple reversible redox reactions.     

Measurement of bisphenol A in human serum by gas chromatography/mass spectrometry

The purpose of this study is to establish an easy and accurate method for the determination of bisphenol A (BPA) in the human serum. The samples were applied to the C₁₈ solid phase extraction (SPE) column for clean up of samples. The BPA is conjugated with tetrabutylammonium hydrogen sulfate as the counter ion in alkali solution. The ion paired BPA is moves from the aqueous phase to the organic phase as an ion paired extraction. BPA extracted from human serum were derivatized with pentafluorobenzyl bromide (PFBBr). The derivative was analyzed by gas chromatography (GC)/mass spectrometry (MS) using negative chemical ionization (NCI). The instrumental detection limit of BPA was 5 pg/ml (10 fg). The instrumental response between 0.01 and 100 pg/ml of BPA standards was linear (r²=0.998). The recovery of BPA spiked into human serum was 101.0±4.63 (1 pg/ml) and 100.9±3.75 (10 pg/ml), respectively. The concentration of BPA in the human serum from 20 individuals was 0.54 pg/ml.     

Heat-capacity measurements and thermodynamic functions of crystalline adenine; revised thermodynamic properties of aqueous adenine

The standard molar heat capacity C^°_p,m of adenine(cr) has been measured using adiabatic calorimetry over the range 6<(T/K)<310 and the results used to derive thermodynamic functions for adenine(cr) at smoothed temperatures. At T=298.15 K, C^°_p,m=(142.67±0.29) J · K⁻¹ · mol⁻¹ and the third law entropy S^°_m=(145.62±0.29) J · K⁻¹ · mol⁻¹. The standard molar Gibbs free energy of formation Δ_fG^°_m at T=298.15 K for crystalline adenine was calculated, using the standard molar enthalpy of formation for the compound and entropies of the elements from the literature, and found to be Δ_fG^°_m=(301.4±1.0) kJ · mol⁻¹. The results were combined with solution calorimetry and solubility measurements from the literature to yield revised values for the standard molar thermodynamic properties of aqueous adenine at T=298.15 K: Δ_fG^°_m=(313.4±1.0) kJ · mol⁻¹, Δ_fH^°_m=(129.5±1.4) kJ · mol⁻¹, and S_m^°=(217.68±0.44) J · K⁻¹ · mol⁻¹.